Commit graph

1189 commits

Author SHA1 Message Date
René Mayrhofer
e457d22261 Make GBit switch work on RB2011
This change is required to make the GBit switch work on my Mikrotik Routerboard RB2011UiAS-RM, and I assume that the other RB2011 variants are exactly the same in terms of the switch. I have tested the board without and with the patch and confirm that the GBit ports are not supported at all (i.e. no communication works) with the current version in trunk and that everything works with the patch applied. The test box has been running for a few days with the patch applied, and does not show any performance problems in a test setting. I have not used it with LEDE in production so far, but with a previous turnk version of OpenWRT for many years - with the same patch applied. I therefore have good indication that it is stable.

For the record, the switch chip on my test box is identified as
	switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0

The value 0x6f000000 has been taken from the table at https://wiki.openwrt.org/toh/mikrotik/rb2011uias with the previous discussion thread still online at https://lists.openwrt.org/pipermail/openwrt-devel/2014-December/029949.html.
One definite improvement from the older OpenWRT trunk version I have been running in production and current LEDE trunk is that the SFP interface can be kept in the default configuration without excessive kernel messages about it constantly going up and down. I have not yet tested an actual SFP module, though.

Performance seems to be reasonable. Routing between two GBit ports on that switch separated by different VLANs with the default firewall ruleset (and one additional rule two allow traffic between the VLANs), but without NAT, iperf3 results are:
	[ ID] Interval           Transfer     Bandwidth       Retr
	[  4]   0.00-10.00  sec   508 MBytes   426 Mbits/sec  102             sender
	[  4]   0.00-10.00  sec   506 MBytes   425 Mbits/sec                  receiver
With a connection going through NAT (also 2 ports on the same GBit switch, same ruleset, but NAT active), routing performance drops to around 250 MBit/s.
(Note that RouterOS achieves beyond 900 MBit/s on the same hardware with the default rule set and the FastTrack rule active even for NAT, see https://wiki.mikrotik.com/index.php?title=Manual:IP/Fasttrack and http://www.mikrotik.com/download/share/FastTrack.pdf).

Summarizing, I strongly recommend to apply this patch in trunk, so that the GBit switch chip rev. 4 can be supported upstream in the next LEDE release (hopefully soon).

Signed-off-by: René Mayrhofer <rene@mayrhofer.eu.org>
2017-05-25 09:22:42 +02:00
John Crispin
bad2f9c4dc Revert "ar71xx: Add support for Teltonika RUT900"
This reverts commit 224e5f5efa.

pepe2k pointed out that this was not ready to merge

Signed-off-by: John Crispin <john@phrozen.org>
2017-05-18 15:31:47 +02:00
Steffen Weinreich
224e5f5efa ar71xx: Add support for Teltonika RUT900
Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet
ports, I/O, RS232, RS485, GPS.

The device ist based on a Atheros AR9344 rev 3,

Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM
- 16 MB of FLASH
- Serial Console header on a Card Board edge connector
- 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN)
- 2.4 GHz Wifi
- 2x external, detachable Wifi antennas
- LTE Modem Huawei ME909u-521 (Also other Modem seen)
- 2x LTE antennas
- 1x GPS antenna
- 7x LED, 1x button
- 1x USB Connector
- 1x Serial RS232
- 1x Serial RS485
- 1x MicroSD Card

The GPL sources of the device are available at www.teltonika.lt/gpl/
and are based on OpenWRT Barrier Breaker (14.07)

Running from tftp:

The Router starts into the uboot Webupdater if the Button ist pressed
more than 3 seconds, if no Network cable is attached it starts the
uboot serial console, from there the router loads the firmware image
via tftpboot from 192.168.1.2:firmware.bin (the router has the
192.168.1.1). With bootm the loaded image will be booted.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
2017-05-18 14:47:53 +02:00
Chris Blake
10d11859df ar71xx: add support for Aerohive AP-121
This adds support for Aerohive AP-121 access point.

Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204

Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:

dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[minor text changes in commit subject and description, fixed
alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh,
fixed code style issues in mach-hiveap-121.c, ubinized factory image]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:58:59 +02:00
Mantas Pucka
68b5d34f69 ar71xx: add support for 8devices Rambutan development board
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan

This commit adds basic support for Rambutan development kit

Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header

Flash instructions:
Stock firmware is OpenWrt, so use:
 sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
 tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
 nand erase.part ubi
 nand write 80060000 ubi ${filesize}

Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Ludwig Thomeczek
43a7a1a05e ar71xx: add support for UniFi-AC-Mesh
This adds the build option for the new UniFi AC Mesh.
It is a direct hardware copy from the AC Lite.

- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 1 1000M - POE
- Wireless:
        2.4G: QCA9563
          5G: UniFi Chip, QCA988X compatible

Thanks to Frank Dietz for testing.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[wrapped too long lines in mach-ubnt-unifiac.c]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Mathias Kresin
e20965811d ar71xx: fix ath9k default LED changes fallout
Since 192f0a3db8 ("ath9k: unset the default LED pin if used by
platform leds") the default ath9k wireless LED is not set as soon as
any pin of the ath ath9k gpio controller is used.

All touched boards have leds defined which are using the gpio pins
exposed by the ath9k driver but rely on a default set wireless led
trigger.

Add the wireless leds were missing and setup the wireless phy trigger
in userspace.

Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
1f5ea4eae4 ar71xx: add correct named default wireless led by using platform leds
Instead of renaming the default wireless led attached to the wireless
chip, add a new led using the platform leds with the phy0tpt trigger
set in userspace.

When switching ar71xx to device tree, the same can be done by using the
build in GPIO controller and without adding new bindings.

Drop the now unused platform code.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-08 14:30:00 +02:00
Christian Mehlis
dc4eae7a8c ar71xx: Compex WPJ563 support
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G

Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer

Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000

Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize

Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-30 09:57:22 +02:00
Leon M. George
6c937df749 ar71xx: wpj531: fix GPIOs for LED
/sys/devices/platform/leds-gpio/leds/ was not initialised with working LEDs.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-03-27 08:36:32 +02:00
Piotr Dymacz
4436979c83 ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.

CPE505 is an outdoor CPE with PoE support and detachable antennas.

Both devices are based on Qualcomm/Atheros QCA9531 v2.

Common specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB

R602N specification:

- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button

CPE505N specification:

- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button

Flash instructions:

It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").

Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:

fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"

Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.

If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:

1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset

These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".

Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 17:59:47 +01:00
Vaclav Svoboda
0d9adb4832 ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.

- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
   (v2: Macronix MX 25L323F)
   (v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-23 09:41:15 +01:00
Ryan Mounce
978998628f ar71xx: add support for MikroTik hAP ac
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).

All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Ryan Mounce
540edf7045 ar71xx: add support for MikroTik hAP ac lite
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).

The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Thibaut VARENE
e1f3cf7ede ar71xx: mikrotik: prepend "RouterBOARD" to machine name for NOR devices
When the device name doesn't already contain "RouterBOARD", this patch adds
this string to the machine name.

Most NOR devices already have "RouterBOARD" in their hardware-stored device name,
but not all of them.

This patch also makes the code more robust against buffer overflows.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Thibaut VARENE
e3dc036cbf ar71xx: add support for RB LHG 5nD
This patch adds support for the MikroTik RouterBOARD LHG 5
https://routerboard.com/RBLHG-5nD

Specifications:
- SoC: Atheros AR9344 (600MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin AR9344 5GHz, 2x2:2
- Ethernet: 1x100M

Initial flash via initramfs, like all other RB devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Daniel Gonzalez Cabanelas
ad9ad376bb ar71xx: WNDR4300: Fix switch HW controlled LEDs
The Netgear WNDR4300, equipped with an Atheros AR8327 Gigabit Switch,
has two LEDs on each port for monitoring LAN activity, but it currently
only uses one. Fix the configuration to use both.

The patch provides this new configuration:
- green LED: 1 Gbps link, 4Hz blink frequency
- amber LED: 10/100 Mbps link. 4Hz for 100Mbps, 2Hz for 10Mbps

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2017-03-13 00:12:07 +01:00
Piotr Dymacz
09862bb006 ar71xx: fix Wallys DR344 ethernet MAC addresses offsets
Without this fix, ethernet interfaces on Wallys DR344 use random MAC
addresses.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:52:19 +01:00
Piotr Dymacz
e213647399 ar71xx: fix machine name for several devices
Be consistent with form and format of the vendor name.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 17:39:12 +01:00
Shuanglin Liu
53ef20f65a ar71xx: add support for Rockeetech AP531B0
Specification:
- SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB))
- RAM: 64 MiB DDR2
- Storage: 16 MiB of flash (optional 16 MiB second flash)
- Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0) 1x100M (port 4)
- PCI-E: x1
- SIMcard slot: x1
- USB 2.0 port: x1 (optional)
- Ext GPIO pin: x8
- UART for serial console: x1
- External watchdog: x1 (optional)
- Power supply: 9-48V (DC jack/passive PoE)

Installation through tftp:
- Copy <Firmware Image Name> into tftp directory
- Connect board via ttl port and Ethernet port
- Boot the AP531B0
- When "Autobooting in 1 seconds" appears press Enter
- Set serverip and ipaddr appropriate
  (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1)
- Enter "tftp 0x8050000 <Firmware Image Name>"
- Enter "erase 0x9f050000 +$filesize"
- Enter "cp.b 0x80500000 0x9f050000 $filesize"
- Enter "reset"

Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
2017-03-12 17:38:31 +01:00
Wojciech Jowsa
f223c4a923 ar71xx: set status led for the gl-* boards
Signed-off-by: Wojciech Jowsa <w.jowsa@radytek.com>
2017-03-06 07:50:11 +01:00
Thibaut VARENE
f6a52bf337 ar71xx: Enable mtdsplit support for RB SPI NOR devices
This patch enables mtdsplit for the MikroTik subtarget.
It converts mach-rbspi.c to use a single "firmware" partition.
Finally, it converts the SPI NOR profile to metadata images:
the original combined-image format is gone, the images are now
"standard" sysupgrade images with metadata appended.

Note: kernel2minor apparently pads the kernel container to erase-block
boundary, but this is undocumented behaviour, so we do not rely on it
and call pad-to anyway.

Note: in platform.sh, the boards are tested last in platform_check_image()
as this should eventually become the "*)" default case when more devices
switch to metadata images.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-22 22:52:20 +01:00
Thomas Roberts
f9278337cf ar71xx: add support for TL-WR802N Version 2
This patch adds support for the TP-Link TL-WR802N Version 2.

Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
2017-02-20 09:10:17 +01:00
Felix Fietkau
72327d1757 ar71xx: fix ethernet PLL configuration for QCA956x
QCA956x is configured like AR934x, not like the older chips.
Should fix ethernet hangs when using the WAN port without SGMII

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-17 12:16:13 +01:00
Henryk Heisig
d6baeb5c48 ar71xx: fix lan ports on archer C59 and C60
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-02-17 10:30:48 +01:00
Karol Dudek
58fc50f1b0 ar71xx: add support for 8devices Lima board
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.

Specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO

Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery

Tested on:

- Lima development kit

Signed-off-by: Karol Dudek <karoiz@sli.pl>
2017-02-17 10:19:09 +01:00
Thibaut VARENE
748e701b74 ar71xx: add preliminary kernel support for several RB SPI NOR devices
The cAP 2nD, mAP 2nD and wAP 2nD apparently all share the same QCA953x/SPI-NOR
platform.

This patch adds preliminary kernel support based on init data used in
Mikrotik's linux-3.3.5 kernel patch. Since this is totally experimental and
untested, the necessary glue in base-files has not been added, the code is
provided as a starting point in case somebody with that hardware wants to help
getting it supported.

The cAP lite (cAPL 2nD) should also be supported once it is determined whether
or not it uses the same board identifier as the mAP lite.

Code has been successfully built and has no side effect (no impact on already
supported devices).

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:59 +01:00
Thibaut VARENE
b2044a7f60 ar71xx: add support for RB750r2
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2

Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)

This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
19f42663d2 ar71xx: add support for RB750UPr2
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

This ethernet router is based on the same platform as the wireless router hAP.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
8cbb2ac633 ar71xx: add support for RB951Ui-2nD
This patch adds support for the MikroTik RouterBOARD hAP
https://routerboard.com/RB951Ui-2nD

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
b18bae37a4 ar71xx: provide support for RB-941-2nD via mach-rbspi.c
This patch implements support for the hAP lite in mach-rbspi.c

hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Thibaut VARENE
c59fa94eee ar71xx: add support for RB mAP L-2nD
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD

Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M

This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Alexandru Gagniuc
6cce9557a0 ar71xx: Add support for D-Link EBR-2310 Rev. C
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2017-02-14 12:27:14 +01:00
Piotr Dymacz
56561b9f51 ar71xx: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-14 12:25:33 +01:00
Sven Eckelmann
5e61a8331d ar71xx: add kernel support for the OpenMesh A40 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
417f9e7e82 ar71xx: add kernel support for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
e1b50457b0 ar71xx: add kernel support for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Piotr Dymacz
c3ef8daff4 ar71xx: fix indentation in Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Piotr Dymacz
cc1fb9662c ar71xx: drop help sections from Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Piotr Dymacz
4fe92554ac ar71xx: select ATH79_NVRAM only by boards actually use it
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Mathias Kresin
893962bcf8 Revert "ar71xx: fix Archer C7 LED colour names"
This reverts commit e79ecb4c26.

The commit was incomplete and the issue that should be fixed isn't
that easy fixable. The Archer C7 mach file is used for the Archer C5,
WDR4900 and WDR7500 as well. Where the WDRs in compare to the Archer
do have blue LEDs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-27 22:16:24 +01:00
Mathias Kresin
e79ecb4c26 ar71xx: fix Archer C7 LED colour names
All LEDs on this board are green.

Fixes: FS#409

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-27 11:10:10 +01:00
Henryk Heisig
e39dc8d823 ar71xx: add support to TP-Link Archer C59v1 and C60v1
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB

TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")

Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:21 +01:00
Henryk Heisig
eec0c41375 ar71xx: QCA956X: add missing register
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-01-26 11:38:20 +01:00
John Crispin
236fcedc51 Revert "ar71xx: wrt400n: lift size limit on kernel and rootfs part"
This reverts commit 78c2ec0f47.

The builders were failing with a segfault when generating the image

Signed-off-by: John Crispin <john@phrozen.org>
2017-01-20 06:43:13 +01:00
YuheiOKAWA
261415a660 ar71xx: add support for PQI Air Pen
SoC: AR9331
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

Changes in v2:
alphabetical ordering, tabs fron spaces.
2017-01-20 00:52:48 +01:00
Yousong Zhou
78c2ec0f47 ar71xx: wrt400n: lift size limit on kernel and rootfs part
While at it, convert to new build method

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-20 00:44:46 +01:00
Conor O'Gorman
274546046d ar71xx: add Abicom SC1750 support
Support Abicom International Scorpion SC1750 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB Nor Flash
1x SFP, 1x PCIe
2x 10/100/1000 Ethernet
135x100 mm
802.11ng/g/b
802.11ac/an/a

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:40 +01:00
Conor O'Gorman
d38ffd8cd9 ar71xx: add Abicom SC450 support
Support Abicom International Scorpion SC450 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:33 +01:00
Conor O'Gorman
eb97f41fc2 ar71xx: add Abicom SC300M support
Support Abicom International Scorpion SC300M Module

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:27 +01:00
Thibaut VARENE
29d0ac35bd ar71xx: mark soft_config mtd part as writeable for RB-941-2nD
The soft_config partition must be writeable for rbcfg to be able to
enact changes to the routerboot configuration.
The read-only flag was a mistake in the initial patch. Removing it
brings mach-rb941.c in line with all other RB platforms.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-01-18 12:05:43 +01:00
Thibaut VARENE
3f7841a70a ar71xx: add support for RB-941-2nD
Add full support for Mikrotik RB-941-2nD (hAP lite)

Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
Felix Fietkau
9db9072d67 ar71xx: convert mikrotik routerboard support to UBI
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.

There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
João Chaínho
ace9d1fb6f ar71xx: Detect USB port on Mikrotik RB750UP
The USB port on Mikrotik RB750UP isn’t detected. This patch provides a fix. Tested and working.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2017-01-15 17:43:14 +01:00
Matthias Schiffer
1fef80f29c
ar71xx: add support for TP-Link WBS210/510
The devices are mostly identical to the CPE210/510, but use external
antennas.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-01-05 16:01:17 +01:00
Felix Fietkau
af79fdbe4a ar71xx: remove a non-upstream spi core patch
- use standard flags instead
- remove dead code from the rb4xx spi drivers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:13 +01:00
Tal Keren
9c475eca3e ar71xx: add support for TP-Link RE450
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.

The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)

The result factory image is flashable from the stock web ui.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-22 14:50:05 +01:00
Ludwig Thomeczek
1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
David Lutz
aada15af93
ar71xx: add support for TP-LINK TL-WR940N v4
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
2016-12-16 11:12:46 +01:00
Gad Krumholz
21cb84435a ar71xx: Added missing support for Linksys E2100L
It's based on the WRT160NL according to
https://wiki.openwrt.org/toh/linksys/e2100l

Based on research done here: https://forum.openwrt.org/viewtopic.php?id=24244
and here: https://forum.openwrt.org/viewtopic.php?pid=120791#p120791 this patch
was conceived.

Signed-off-by: Gad Krumholz <gad.krumholz@gmail.com>
[Jo-Philipp Wich: fix ordering, move addpattern change into separate commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-14 18:42:48 +01:00
Huan Truong
fd62fa752b ar71xx: Add support for Netgear WNR2000v1
This patch adds supports for the WNR2000v1 board with 4MB flash, and
produces device-specific factory, rootfs, and sysupgrade files for the
WNR2000v1. This board is errorneously claimed as supported on the OpenWRT
wiki as AP81, but AP81 image would not work because of APT81 image
requiring having 8MB of flash, while WNR2000v1 has only 4MB.

The image requires the u-boot bootloader to be modified to fuhry's
bootloader first.

Short specification:

- CPU: Atheros AR9132
- 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps
- 4 MB of Flash
- 32 MB of RAM
- UART header (J1) on board
- 1x button

Factory/Initial flash instructions:

- Set up a TFTP server on your local machine.
- Download the uImage for ar71xx-generic and the rootfs image for
  ar71xx-generic-wnr2000 and save in the tftp server root.
- Gain serial access to the router via the UART port (telnetenable over
  the network only won't work!).
- Upgrade the u-boot bootloader to fuhry's version by running the
  script: http://fuhry.com/b/wnr2000/install-repart.sh
- When the router restarts, interrupt u-boot and gain access to u-boot command line.
- Repartititon the board and flash initial uImage and rootfs as follow.

Commands to type in u-boot:

	# tells u-boot that we have a tftp server on 192.168.1.10
	setenv serverip 192.168.1.10

	# tells u-boot that the router should take the address 192.168.1.1
	setenv ipaddr 192.168.1.1

	# erase the region from 0x050000-0x3f0000
	erase 0xbf050000 +0x3A0000

	# loads sqfs.bin on TFTP server, and put it to memory address 0x81000000
	tftpboot 0x81000000 sqfs.bin
	# it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ
	# copy bit by bit 0xZZZZZZ bytes from offset 0x050000
	cp.b 0x81000000 0xbf050000 0xZZZZZZ

	# same to the uImage.bin, write it right next to sqfs.bin
	# again, 0xYYYYYY is the length that tftpboot reports
	tftpboot 0x81000000 uImage.bin
	cp.b 0x81000000 0xbf2a0000 0xYYYYYY

	# We need to tell the kernel what board it is booting into, and where to find the partitions
	setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd"

	# Tell u-boot where to find the uImage
	setenv bootcmd "bootm 0xbf2a0000"

	# Tell u-boot to save parameters to the u-boot-env partitions
	saveenv

	# Reset the board
	reset

Tested on:

- WNR2000v1 board.
- Initial flash works.

Known bugs:

- I don't know why factory image doesn't work on initial flash on stock
  firmware in u-boot recovery mode while it should.
- Sysupgrade does not yet work, if you do -f it will mess up your
  installation (requiring a reinstall of sqfs and uImage).

Signed-off-by: Huan Truong <htruong@tnhh.net>
2016-12-14 10:37:01 +01:00
Felix Fietkau
a5923cd549 ar71xx: remove PB92 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
30285facbe ar71xx: remove AP113 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
4c8a9b8e39 ar71xx: remove AP81 reference design board support
This board is very old and unlikely to still be relevant today.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
441ee62931 ar71xx: remove AP83 reference design board support
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
fa04682f21 ar71xx: clean up spi controller related patches
Remove various hacks for fast read, un-break device tree support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:17 +01:00
Piotr Dymacz
c198ca682c ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00
Matthias Schiffer
9c5af2489a
ar71xx: fix LEDs and sysupgrade support for TL-WA801ND v3
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-06 19:08:35 +01:00
Felix Fietkau
2135e54c00 ar71xx: set GPIO reset line for Ubiquiti NanoStation Loco XW
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-04 11:41:50 +01:00
Piotr Dymacz
6998b8a054 ar71xx: move DomyWifi DW33D to nand subtarget
This device uses NAND FLASH, so it should be kept in nand subtarget.

Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-24 22:37:40 +01:00
Piotr Dymacz
e33dcd1cfe ar71xx: add support for YunCore CPE830
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.

Use the same flash approach as for YunCore AP90Q.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
eb9ba2b91e ar71xx: add support for YunCore CPE870
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:

- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset

Vendor firmware access (login/password): Admin/5up

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
01dda0659e ar71xx: add support for YunCore AP90Q
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Flash instruction under vendor fimrware, using telnet/SSH:

1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
31952dbd1c ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530N
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.

All 3 devices are based on Qualcomm/Atheros QCA9531 v2.

COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Henryk Heisig
0d760bfba8 ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partition
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-16 11:01:18 +01:00
FUKAUMI Naoki
0165203304 ar71xx: add support for Buffalo BHR-4GRV2
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2016-11-16 10:54:33 +01:00
Matthias Schiffer
7ef0d7c4fc
ar71xx: enable HSR tuner on Ubiquiti UAP Outdoor+
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-15 18:54:07 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Christian Mehlis
7cb82d4b70 ar71xx: fix ethernet on wpj344 board
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
2016-10-31 12:52:56 +01:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Chris Blake
28dd52b079 ar71xx: add mac partition to the MR12/MR16
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).

The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.

Once this partition is added to a device, you can set your MAC doing the
following:

mtd erase mac
echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5
sync && reboot

Where 00:18:0a:33:44:55 is your MAC address.

This was tested, and confirmed working on both the MR12 and MR16.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Christian Lamparter
098f7156cc ar71xx: add support for the Airtight C-60
This patch adds support for the Airtight C-60.

SOC:	Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM:	128 MiB
NOR:	MX25L3205D 4MiB
NAND:	ST Micro NAND 32MiB 3,3V 8-bit
SW-NET:	AR8327N (2 Ports)
WLAN1:	Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2:	Dual-Band AR9300 Rev:4 PCIe Chip

The switch is setup for an accesspoint:
	LAN1: (gigabit) is the wan-port.
	LAN2: (fast ethernet) is bridged with the br-lan.

Flashing Guide (via initramfs):
  1. Connect a PC to the serial port of the C-60.
     power up the C-60.

     Enter u-boot command prompt:
     #> nand erase
     #> setenv bootcmd "bootm 0x9f060000"
     #> saveenv
     #> setenv ipaddr 192.168.1.1
     #> setenv netmask 255.255.255.0
     #> setenv serverip 192.168.1.100
     #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
     #> tftpboot
     #> bootm

  2. Wait for the C-60 to boot LEDE.
     On the root prompt. Enter:
     # ubiformat /dev/mtd4
     # ubiattach -p /dev/mtd4

  3. After that copy the sysupgrade.tar onto the router and run:
     # sysupgrade sysupgrade.tar

     to flash the image.

Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-15 11:36:50 +02:00
Matthias Schiffer
594f0e80ce
ar71xx: add kernel support for D-Link DIR-869 A1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:36 +02:00
Piotr Dymacz
92870eac27 ar71xx: comsetic cleanups in files/arch/mips/ath79/{Makefile,machtypes.h}
Keep everything in alphabetical order and aligned in columns.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
c142df3094 ar71xx: fix LED names for GL Innovations boards
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Chris Blake
68d649f5cd ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker Gateway
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-09-27 17:50:22 +02:00
Felix Fietkau
83997146e7 ar71xx: disable flow control to the built-in switch on AR934x
It apparently causes a regression on some devices if the ethernet cable
is plugged in while booting.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-25 11:54:31 +02:00
Piotr Dymacz
f478fba663 ar71xx: add support for Zbtlink ZBT-WE1526
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)

Flash instruction:

Use sysupgrade in vendor firmare which is based on OpenWrt.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-08-18 09:49:18 +02:00
Zhao Gang
42305ae24a ar71xx: add support for gl-mifi
This add initial support for gl-mifi.
Product page: http://www.gl-inet.com/mifi/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-24 06:38:30 +02:00
Zhao Gang
d963ddf042 ar71xx: add support for gl-ar300m
This add initial support for gl-ar300m router.
Product page: http://www.gl-inet.com/ar300m/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-20 00:21:48 +02:00
Piotr Dymacz
d2c9b169b3 ar71xx: add support for jjPlus JWAP230
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers

Default configuration:

- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space

Flash instruction (do it under U-Boot, using RS232):

1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Piotr Dymacz
e767980eb8 ar71xx: add support for Wallys DR531
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers

Default configuration:

- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Felix Fietkau
be08fdd007 ar71xx: disable pdata->use_flow_control for QCA9558
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-27 12:12:40 +02:00
Felix Fietkau
75b2105cd3 ar71xx: rename ethernet pdata->builtin_switch to use_flow_control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-27 12:12:40 +02:00
Felix Fietkau
26b8db2537 ar71xx: enable flow control for ethernet MACs with built-in switch
Should fix LAN speed issues on some devices. This is an updated version
of the previously reverted commit with the same name.
It improves the check for MACs connected to a built-in switch

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-26 11:21:17 +02:00
Alexander Couzens
c2e0c41842 Revert "ar71xx/cpe510: use second wifi calibration table"
Using the high power table can damage the device in some cases.

This reverts commit bf27ac019c.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-16 21:11:24 -07:00
Arne Zachlod
f869ffdd62 ar71xx: mach-ubnt-xm.c convert patches to mach file
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2016-06-13 22:51:43 +02:00
Allan Nick Pedrana
e61fe4e4d7 ar71xx: add support for OpenEmbed SOM9331
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.

Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
2016-06-07 11:21:55 +02:00
Felix Fietkau
7eeb254cc4 treewide: replace nbd@openwrt.org with nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-07 08:58:42 +02:00
KeLei Liang
563e9d5e1b ar71xx: add WRTnode2Q support
Signed-off-by: KeLei Liang <xzmu@wrtnode.com>
2016-06-06 14:58:11 +02:00
Stijn Segers
d2a91f9853
ar71xx: Fix TL-WR841N v11 LEDs, use separate machine
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-05-31 17:36:51 +02:00
Alexander Couzens
bf27ac019c ar71xx/cpe510: use second wifi calibration table
The cpe510 has two calibration tables. The first calibration
table requires to modify ath9k driver to work (patched tx gain table).

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:50 +02:00
Alexander Couzens
c5ff273d85 ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510
Split profile into 2GHz and 5GHz. The 5GHz devices are
quite "special". The 2 GHz works perfect.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:49 +02:00
Sven Eckelmann
f7719dca71 ar71xx: add kernel support for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
8010e8a370 ar71xx: add kernel support for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Alexander Couzens
94e23bf740 ar71xx/cpe510: enable LNA for CPE210/220/510/520
The LNA improves the rx path. Within a simple test setup
it improved the signal from -60dbm to -40dbm.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-20 13:18:57 +02:00
Felix Fietkau
5b34dffcbd ar71xx: fix DDR write buffer flushing issues with 4.4
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-15 20:55:39 +02:00
Cezary Jackiewicz
0b45bec22c
ar71xx: add support for TP-LINK TL-WR842N/ND v3
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB

AP143 platform, similar to tl-wr841n v10/v11, but with USB

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-14 21:45:16 +02:00
John Crispin
cc831e23e1 ar71xx: add proper support for Archer-C7 V2
This has minor differences to the V1

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-14 21:26:08 +02:00
John Crispin
f816472f78 ar71xx: Fix TP-LINK Archer-C5/C7 v2 rfkill
Fix ARCHER_C7_GPIO_BTN_RFKILL, which is attached to GPIO23

Signed-off-by: Lars Buerding <lb.wrt@metatux.net>
2016-05-12 03:29:36 +02:00
P.Wassi
8307c2fe68 ar71xx: Add support for Ubiquiti UniFi AP AC PRO
Add support for the Ubiquiti UniFi AP AC PRO
Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
P.Wassi
c855e70491 ar71xx: Rename unifiac to unifiac-lite
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.

Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
blogic
75629fb2a8 ar71xx: add TP-Link TL-WR810N support
This patch adds support for the TP-Link TL-WR810N.
https://wiki.openwrt.org/toh/tp-link/tl-wr810n

Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com>

SVN-Revision: 49286
2016-05-10 10:43:12 +02:00
blogic
ba3ed629ea ar71xx: Fix eth0 support for Ubiquiti UniFi AP AC
Fix eth0 support for the Ubiquiti UniFi AP AC
Signed-off-by: Paul Wassi <p.wassi at gmx.at>

SVN-Revision: 49277
2016-05-10 10:43:12 +02:00
John Crispin
ee53a240ac ar71xx: Add support for the OMYlink OMY-G1
https://wiki.openwrt.org/toh/omylink/omy-g1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49258
2016-04-26 11:44:36 +00:00
Hauke Mehrtens
9759aba429 ar71xx: fix build error
This fixes a build error introduced in r49193.

This closes #22230

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49194
2016-04-17 22:03:58 +00:00
Hauke Mehrtens
00675abc3b ar71xx: fix build with kernel 4.4
The file linux/mdio-gpio.h was moved to linux/platform_data/mdio-gpio.h
in kernel 4.4

Reported-by: Arjen de Korte <arjen+openwrt@de-korte.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49193
2016-04-17 19:10:13 +00:00
John Crispin
5f1a82ec4f ar71xx: add TP-Link TL-WA901ND-v4 support
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 49158
2016-04-09 10:26:46 +00:00
John Crispin
d9799dea89 ar71xx: add support for Compex WPJ342
OpenWrt can be flashed with following uboot commands:

tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 49157
2016-04-09 10:26:41 +00:00
John Crispin
886cb9a744 ar71xx: add kernel support for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49149
2016-04-09 10:26:15 +00:00
John Crispin
69965212bd ar71xx: add kernel support for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49141
2016-04-09 10:25:47 +00:00
John Crispin
8e2a35afc6 ar71xx: WPN824N: enable buttons
Enable buttons connected to the GPIOs of the AR9285.

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 49109
2016-04-01 07:12:07 +00:00
John Crispin
38a48a9b42 ar71xx: WPN824N: set WLAN LED name
Make use of ap9x_pci_setup_wmac_led_name() to set the name of the WLAN
LED.

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 49108
2016-04-01 07:12:03 +00:00
John Crispin
ba2d1ccffa ar71xx: WNR2200: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49101
2016-04-01 07:11:34 +00:00
John Crispin
3da1ef38c1 ar71xx: WNR2200: fix for random WLAN MAC
Fix for invalid/random/duplicate WLAN MAC address in WNR2200.
Permanent platform MAC is calculated and assigned during system startup.
WLAN MAC follows wired Ethernet interface addresses.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49100
2016-04-01 07:11:27 +00:00
Luka Perkov
8258f8edb6 ar71xx: cosmetic fix of alfa ap120c/ap96 ordering
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49086
2016-03-24 21:09:34 +00:00
Luka Perkov
ebaba15331 ar71xx: add support for ap120c
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49082
2016-03-23 22:31:38 +00:00
John Crispin
5b2d89f060 ar71xx: WNR1000v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49076
2016-03-23 12:52:35 +00:00
John Crispin
58143e9b65 Revert "ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg"
Not all mach-* files set all boards correctly in ETH_CFG. They depend on
some preset values by u-boot which were not previously modified by
ath79_setup_qca955x_eth_cfg. Avoiding to modify them in this function keeps
it backward compatible for these boards.

This reverts commit 119b8ab2c2eac237ec4e9c4d0ed53df22b5c6978.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49072
2016-03-23 12:52:20 +00:00
John Crispin
b269a3520d Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x"
The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some
boards. These boards depend on the preset values of u-boot which may
differ.

This reverts commit f2d4bb96b62512caa161dcc2867c91692fb16a38.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49071
2016-03-23 12:52:17 +00:00
John Crispin
26d18d4e07 ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR1750
The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR1750 can be used instead.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49070
2016-03-23 12:52:12 +00:00
John Crispin
bdf76faa3e ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR900
The MR900 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR900 can be used instead.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49069
2016-03-23 12:52:09 +00:00
John Crispin
1cdd3403ba ar71xx: WNR1000v2: fix for random WLAN MAC
Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3
and WNR612v2.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49051
2016-03-20 14:41:58 +00:00
John Crispin
4d6c4994fc ar71xx: Use PHY fixups for Open Mesh MR1750
The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.

This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.

Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49031
2016-03-16 09:27:14 +00:00
John Crispin
ebcce35be4 ar71xx: Use PHY fixups for Open Mesh MR900
The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.

This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.

Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49030
2016-03-16 09:27:11 +00:00
John Crispin
22c5f96c6b ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x
Some u-boot versions for QCA955x change the delays based on the link speed
during boot. This usually breaks the support of other linkspeeds when
OpenWrt is booted. It also conflicts with the
at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own
values in QCA955X_GMAC_REG_ETH_CFG.

The default RGMII values from the Atheros u-boot are currently used to
preset the existing mach files. These may have to be adjusted for boards
using different values but which are not currently set them explicitely in
OpenWrt.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Christian Beier <cb@shoutrlabs.com>
Cc: Chris R Blake <chrisrblake93@gmail.com>
Cc: Benjamin Berg <benjamin@sipsolutions.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Dirk Neukirchen <dirkneukirchen@web.de>
Cc: Christian Mehlis <christian@m3hlis.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 49029
2016-03-16 09:27:08 +00:00
John Crispin
be68f34708 ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg
Some u-boot versions for QCA955x set currently not cleared bits depending
on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c
file is responsible to select the correct configuration bits and thus the
ath79_setup_qca955x_eth_cfg has to clear the unset.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49028
2016-03-16 09:27:04 +00:00
John Crispin
3fd98db818 ar71xx: Add support for the OMYlink OMY-X1
This patch adds support for the OMYlink OMY-X1

https://wiki.openwrt.org/toh/omylink/omy-x1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49026
2016-03-16 09:26:58 +00:00
John Crispin
05d73a2a73 ar71xx: Arduino Yun board 'WLAN RST' button support
This patch adds support for Arduino Yun board "WLAN RST" button.

Signed-off-by: Hirokazu MORIKAWA <morikw2@gmail.com>

SVN-Revision: 48983
2016-03-10 19:11:13 +00:00
John Crispin
346b1905fb ar71xx: add support for the Telldus TellStick ZNet Lite
Signed-off-by: Micke Prag <micke.prag@telldus.se>

SVN-Revision: 48977
2016-03-10 19:07:26 +00:00
Felix Fietkau
4802f611cb ar71xx: fix qca956x ethernet initialization
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 48937
2016-03-07 08:45:01 +00:00
Felix Fietkau
3f971c0dc8 ar71xx: WNR612v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48924
2016-03-05 09:45:15 +00:00
Felix Fietkau
53b3872ddf ar71xx: WNR2000v3: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48922
2016-03-05 09:45:06 +00:00
Felix Fietkau
6bece706ec mac80211: ath9k: enable GPIO buttons
Enable platform-defined GPIO button support for ath9k device.
Key poller is activated for attached platform buttons.
Requires ath9k GPIO chip access.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48921
2016-03-05 09:45:03 +00:00
Felix Fietkau
a8c15c0204 mac80211: ath9k: enable platform WLAN LED name
Enable platform-supplied WLAN LED name for ath9k device.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 48879
2016-03-02 13:22:40 +00:00