This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other
.dts files that utilize it, ar7161_ubnt_routerstation.dts and
ar7161_ubnt_routerstation-pro.dts.
The modifications to generic-ubnt.mk, config-default, and base-files
necessary for image generation, parsing RedBoot FIS partitions, network
configuration, and sysupgrade are also included.
This reintroduces vital bits from platform_do_upgrade_combined() and its
supporting functions to /lib/upgrade/platform.sh, which were previously
removed from ath79 in 3e9d9f6225 "ath79:
sysupgrade: drop unused platform checks". The new function is called
"routerstation_do_upgrade" and will *only* work for the RouterStation
series of boards. It does however retain the ability to downgrade (e.g.
from master -> 17.01.x using sysupgrade -F).
All hardware is functional including the AR8216 switch (for the Pro),
wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button,
and LED.
Switch and LAN/WAN configuration is the same as it is with the
equivalent ar71xx targets. MAC addresses are assigned based upon the
content stored in the RedBoot config partition.
Flashing via both sysupgrade and TFTP has been confirmed to work. Also,
the initramfs images are now raw .bin files instead of being wrapped in
a uImage (as they currently are in ar71xx), which makes them bootable
with RedBoot.
One notable difference to ar71xx is the inclusion of the RedBoot
"fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in
DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD
parser’s DT binding, whose proper usage is mutually exclusive to
defining a separate fixed-partitions node for "RedBoot config". This
config partition contains the board's base MAC address. The lack of a
hard-coded flash location means that the mtd-mac-address property cannot
be used in the .dts, so instead fconfig is used to read the MAC
addresses from flash in userspace during first boot.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The mt7620 doesn't have a pinmux group named spi_cs1. The cs1 is part
of the "spi refclk" group. The function "spi refclk" enables the second
chip select.
On reset, the pins of the "spi refclk" group are used as reference
clock and GPIO.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds a configuration options which is needed now.
Without this patch the geode build will fail.
Fixes: 4eda2fddf2 ("x86/geode: enable X86_INTEL_LPSS to select PINCTRL")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
WNDR3400v3 needs GPIO 21 pulled high to enable power to USB ports. Add a
kernel patch to do that.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
- Specifications -
CuBox i1:
- SoC: i.MX6 Solo
- Cores: 1
- Memory Size: 512MB
- GPU: GC880
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
CuBox i2 | i2eX:
- SoC: i.MX6 Dual Lite
- Cores: 2
- Memory Size: 1GB
- GPU: GC2000
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
CuBox i4Pro | i4x4:
- SoC: i.MX6 Quad
- Cores: 4
- Memory Size: 2/4 GB
- GPU: GC2000
- Wifi/Bluetooth: Build In
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
Built-in u-boot requires SPL (secondary program loader) to be present on the SD-card regardless of the image type which will be loaded.
SPL is generated by the u-boot-mx6cuboxi package which is preselected by the target device and can be found in bin/u-boot-mx6cuboxi directory.
Flashing the SPL:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=4
dd if=bin/targets/imx6/generic/u-boot-mx6cuboxi/SPL of=/dev/mmcblk0 bs=1K seek=1
Preparing the firmware on the SD-card:
(echo o; echo n; echo p; echo 1; echo ''; echo ''; echo w) | fdisk /dev/mmcblk0
mkfs.ext4 /dev/mmcblk0p1
mount /dev/mmcblk0p1 /mnt
tar -xzf bin/targets/imx6/generic/openwrt-imx6-device-cubox-i-rootfs.tar.gz -C /mnt/
mkdir -p /mnt/boot
cp bin/targets/imx6/generic/{*-uImage,*.dtb,*.scr} /mnt/boot/
Generated u-boot.img needs to be placed on the first partition:
cp bin/targets/imx6/generic/u-boot-mx6cuboxi/u-boot.img /mnt/
To boot from the SD card:
Boot script which sets mmc/dtb parameters and boots the board is automatically sourced.
If this does not work for any reason:
mmc dev 0; load mmc 0:1 $scriptaddr boot/boot.scr; source $scriptaddr
Currently imx6dl-cubox-i.dtb (Dual Lite) and imx6q-cubox-i.dtb (Quad) device trees are available.
Tested on i4Pro, MMC, USB (+ HiD), HDMI and ethernet ports are working.
Wireless and bluetooth are broken ATM. According to SolidRun forums, BCM4329/BCM4330 firmware is used which works fine on older kernels.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Without UHCI a non-trivial number of machines will have no keyboard
without BIOS assistance.
Add XHCI as well in case there are chipsets which don't support legacy
interfaces, and support PCI OHCI controllers also.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
This patch improves faf64056dd by correcting
the partition scheme for the "RouterBoot" section of the flash.
The partition scheme initially submitted is incorrect and does not reflect
the actual flash structure.
The "RouterBoot" section (name matching OEM) is subdivided in several
static segments, as they are on ar71xx RB devices albeit with different
offsets and sizes.
The naming convention from ar71xx has been preserved, except for the
bootloaders which are named "bootloader1" and "bootloader2" to avoid
confusion with the master "RouterBoot" partition.
The preferred 'fixed-partitions' DTS node syntax is used, with nesting
support as introduced in 2a598bbaa3.
"partition" is used for node names, with associated "label" to match
policy set by 6dd94c2781.
Leave a note in DTS to explain how the original author selected the SPI speed.
Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
This patch improves 5684d08741 by correcting
the partition scheme for the "RouterBoot" section of the flash.
The partition scheme initially submitted is incorrect and does not reflect
the actual flash structure.
The "RouterBoot" section (name matching OEM) is subdivided in several
static segments, as they are on ar71xx RB devices albeit with different
offsets and sizes.
The naming convention from ar71xx has been preserved, except for the
bootloaders which are named "bootloader1" and "bootloader2" to avoid
confusion with the master "RouterBoot" partition.
The preferred 'fixed-partitions' DTS node syntax is used, with nesting
support as introduced in 2a598bbaa3.
"partition" is used for node names, with associated "label" to match
policy set by 6dd94c2781.
The OEM source code also define a "RouterBootFake" partition at the
beginning of the secondary flash chip: to avoid trouble if OEM ever makes
use of that space, it is also defined here.
The resulting partition scheme looks like this:
[ 10.114241] m25p80 spi0.0: w25x40 (512 Kbytes)
[ 10.118708] 1 fixed-partitions partitions found on MTD device spi0.0
[ 10.125049] Creating 1 MTD partitions on "spi0.0":
[ 10.129824] 0x000000000000-0x000000040000 : "RouterBoot"
[ 10.136215] 5 fixed-partitions partitions found on MTD device RouterBoot
[ 10.142894] Creating 5 MTD partitions on "RouterBoot":
[ 10.148032] 0x000000000000-0x00000000f000 : "bootloader1"
[ 10.154336] 0x00000000f000-0x000000010000 : "hard_config"
[ 10.160665] 0x000000010000-0x00000001f000 : "bootloader2"
[ 10.167046] 0x000000020000-0x000000021000 : "soft_config"
[ 10.173461] 0x000000030000-0x000000031000 : "bios"
[ 10.190191] m25p80 spi0.1: w25q128 (16384 Kbytes)
[ 10.194950] 2 fixed-partitions partitions found on MTD device spi0.1
[ 10.201271] Creating 2 MTD partitions on "spi0.1":
[ 10.206071] 0x000000000000-0x000000040000 : "RouterBootFake"
[ 10.212746] 0x000000040000-0x000001000000 : "firmware"
[ 10.307216] 2 minor-fw partitions found on MTD device firmware
[ 10.313044] 0x000000040000-0x000000220000 : "kernel"
[ 10.319002] 0x000000220000-0x000001000000 : "rootfs"
[ 10.324906] mtd: device 9 (rootfs) set to be root filesystem
[ 10.330678] 1 squashfs-split partitions found on MTD device rootfs
[ 10.336886] 0x000000b40000-0x000001000000 : "rootfs_data"
Leave a note in DTS to explain how the original author selected the SPI speed.
Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
[rmilecki: dropped "RouterBootFake" partition]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Ubiquiti XM series boards contain a set of RSSI LEDs. Create an UCI
mapping for them, so visual feedback on RSSI is available, when using
userspace RSSI monitor daemon.
Runtime tested using rssileds.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Create aliases for led-booting and led-failsafe pointing at
ubnt:green:link4 LED, forUbiquiti XM series, so visual feedback
on device status becomes available, in order to enter failsafe mode
via button. led-running and led-upgrade aliases are omitted to avoid
conflicting with RSSI LEDs when in normal operation.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ubnt,bullet-m and ubnt,rocket-m targets support only single Ethernet
port, therefore disable creation of WAN zone and interfaces for them,
as their intended purpose is a wireless bridge. This aligns the
configuration with one found in ar71xx target.
ubnt,nano-m target is kept as is, being a two-port device.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Enable ath9k EEPROM extraction on boot for Ubiquiti XM-series boards.
This is required for wireless interface to function.
Runtime tested on Nanobridge M5.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
I-O DATA ETG3-R is a wired router, based on Atheros AR9342.
Specification:
- Atheros AR9342
- 64 MB of RAM
- 8 MB of Flash
- 5x 10/100/1000 Ethernet
- AR8327N
- 2x LEDs, 1x key
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using initramfs image:
1. Connect serial cable to UART header on ETG3-R
2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in
the TFTP directory
3. Set IP address of the computer to 192.168.0.10, connect to the
LAN port of ETG3-R, and start the TFTP server on the computer
4. Connect power cable to ETG3-R and turn on the router
5. Press "Enter" key when the "Hit any key to stop autoboot:" message
is displayed on the console and enter the u-boot cli
6. execute following commands to change kernel address for u-boot
setenv bootsf 1
setenv mtd_kernel1 "bootm 0x9f050000"
saveenv
7. execute "tftpboot; bootm" command to download the initramfs image from
TFTP server and boot with it
8. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for ETG3-R
9. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The device was not included in the /etc/board.d/02_network file, so
the network wouldn't be properly set up on boot.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A.
This is almost same as WRC-2533GST except wireless specs.
Specifications:
- SoC : MT7621A (four logical CPU cores)
- RAM : 128MiB
- ROM : 16MiB of SPI NOR-FLASH
- wireless :
5GHz : 3T3R up to 1300Mbps/11ac with MT7615
2.4GHz : 3T3R up to 600Mbps/11n with MT7615
- Ethernet : 5 ports, all ports is capable of 1000base-T
- Ether switch : MT7530 (MT7621A built-in)
- LEDs : 4 LEDs
- buttons : 2 buttons and 1 slide-switch
- UART : header is on PCB, 57600bps
Flash instruction using factory image:
1. Connect the computer to the LAN port of WRC-1900GST
2. Connect power cable to WRC-1900GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
The former used compatibles aren't defined anywhere and aren't used by
the devicetree source files including them.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to abbfcc8525 ("ramips: add support for GL-inet
GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC
compatible to match the used hardware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
RT5350 neither have rgmii nor a mdio pinmux group. MT7628an doesn't
have a jtag group. Having these groups defined might cause a boot
panic.
The pin controller fails to initialise for kernels > 4.9 if invalid
groups are used. If a subsystem references a pin controller
configuration node, it can not find this node and errors out. In worst
case it's the SPI driver which errors out and we have no root
filesystem to mount.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The intention of 967b6be118 ("ar8327: Add workarounds for AR8337
switch") was to remove the register fixups for AR8337. But instead they
were removed for AR8327.
The RGMII RX delay is forced even if the port is used as phy instead of
mac, which results in no package flow at least for one board.
Fixes: FS#1664
Signed-off-by: Mathias Kresin <dev@kresin.me>
While "rawnand.h" is available in kernel 4.14,
the default for this target is kernel 4.9 in which "nand.h" should be used.
Add an extra check to include the correct file depending on kernel version
Fixes these build errors:
drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory
#include <linux/mtd/rawnand.h>
^~~~~~~~~~~~~~~~~~~~~
compilation terminated.
Fixes: 318e19ba67 ("ar71xx: add v4.14 support")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Sysupgrading to ath79 from ar71xx currently fails because of mismatching
supported_devices. ar71xx is expecting "tl-mr3020" which is missing in
the ath79 image. Upgrading from ath79 is unaffected, as the image
contains the old string for ar71xx and the new one coming from the
device-tree.
Signed-off-by: David Bauer <mail@david-bauer.net>
PISEN WMM003N is never supported by ar71xx, this commit also removed
SUPPORTED_DEVICES for it because it's completely useless.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
The USB port doesn't work. Both Root Hubs are detected as having 0 Ports:
[ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.723267] usbcore: registered new interface driver usbfs
[ 3.729058] usbcore: registered new interface driver hub
[ 3.734616] usbcore: registered new device driver usb
[ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.758357] SCSI subsystem initialized
[ 3.766026] ehci-platform: EHCI generic platform driver
[ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller
[ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00
[ 3.824001] hub 1-0:1.0: USB hub found
[ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller
[ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00
[ 3.894011] hub 2-0:1.0: USB hub found
[ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.908928] usbcore: registered new interface driver usb-storage
[ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
A few words about the shift-register:
AVM used a trick to control the shift-register for the LEDs with only 2
pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple
shift-registers, pulls the latch, moving the shift register-state to
the storage register. It also pulls down MR (normally pulled up) to
clear the storage register, so the latch gets released and will not be
pulled by the remaining bits in the shift-register. Shift register is
all-zero after this.
For that we need to make sure output 7 is set to high on driver probe.
We accomplish this by using gpio-hogging.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1).
Firmware can be uploaded like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link Archer C7 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.
Specification:
- 720 MHz CPU
- 128 MB of RAM (Various chips)
- 8 MB of FLASH (Various chips)
- SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
- minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!)
- 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
- 10x LEDs, 2x software buttons
For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c7-1750>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- Qualcomm Atheros QCA9557
- 128 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz wifi
- 2.4 GHz: SoC internal
- 5 GHz: QCA988x
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1167DGR
2. Connect power cable to WN-AC1167DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Adding tl-wr841-v11 and the rename of tl-wr841n-v9 to tl-wr841-v9 in 01_leds
and 02_network script files are missing in commits cc35c91 and 8db6522.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[merged with identical case in 02_network]
Signed-off-by: Mathias Kresin <dev@kresin.me>
If it isn't a usb led, it shouldn't be used as one by default. It is up
to the user to add such a (mis)configuration for the board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240.
Ported from ar71xx target.
Specification:
- Atheros AR7240
- 32 MB of RAM
- 4 MB of Flash
- 2.4 GHz 2T2R wifi
- 5x 10/100 Mbps Ethernet
- 9x LEDs, 4x keys
- LED: 8x gpio-leds, 1x ath9k-leds
- key: 2x buttons, 1x slide switch
- UART header on PCB
- Vcc, GND, TX, RX from LEDs side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WHR-G301N
2. Connect power cable to WHR-G301N and turn on it
3. Access to "http://192.168.11.1/" and open firmware update page
("ファーム更新")
4. Select the OpenWrt factory image and click execute ("実行") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[fix the SUPPORTED_DEVICES to be compatible with the ar71xx image]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh
script en par with the other implementations using devicetree aliases
to define multiple leds for boot status indication.
By default, use the boot finished led to indicate an upgrade for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The upgrade led is only used if a running led is defined. If no running
led is defined, the upgrade led is ignored and upgrade isn't indicated
at all.
Instead, turn off the running led prior to turning the upgrade led on.
In most cases there isn't any visual change, but it allows to use an
independent led for upgrade indication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the (sys)upgrade state when sourcing the stage2 script instead of
setting the state for each target individual.
This change fixes the, due to a missing state set, not working upgrade
led on ath79 and apm821xx.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device
min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which
is [68, 1500] by default.
It's necessary to set a max_mtu if a mtu > 1500 is supported.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following patch was integrated upstream:
* target/linux/generic/backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
This fixes tries to work around the following security problems:
* CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
* CVE-2018-3646 L1 Terminal Fault Virtualization related aspects
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were integrated upstream:
* target/linux/ipq40xx/patches-4.14/050-0006-mtd-nand-qcom-Add-a-NULL-check-for-devm_kasprintf.patch
* target/linux/mediatek/patches-4.14/0177-phy-phy-mtk-tphy-use-auto-instead-of-force-to-bypass.patch
This fixes tries to work around the following security problems:
* CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
* CVE-2018-3646 L1 Terminal Fault Virtualization related aspects
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the orange led by default to match the bootloader/stock firmware
behaviour. Turn on the green power led after boot to indicate a
finished boot and the orange one off.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message, keep orange power led enabled during early
kernel boot]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the orange led by default to match the bootloader/stock firmware
behaviour. Turn on the blue power led after boot to indicate a finished
boot and the orange one off.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message, keep orange power led enabled during early
kernel boot]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.
The existing led sequences should be the same as before.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The DWR-118-A2 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612EN)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN)
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader
Known issues:
- GELAN not working
- flash is very slow
The status led has been assigned to the dwr-118-a2:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN
https://www.hiwifi.com/enjoy-view
Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7612EN 802.11ac 2T2R 867Mbps
- 5x 10/100 Mbps Ethernet
Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot
Everything is working
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Move the alias node of the TP-Link WR841v9 and rename the phandle of
the qss led to qss_led in preparation for adding the very similar
TP-Link WR841v11.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Remove SUPPORTED_DEVICES from wr841-v9 because it´s not needed and
for consistency rename everything to tl-wr841-v9.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Add ath9k wifi capabilities to WNDR3700 family.
* use kmod-owl-loader to load firmware from "art"
* add wifi to DTS
* add wifi LEDs
Avoid using the same MAC for eth0 LAN and wlan0 by
toggling the eth0 MAC into a locally administered MAC.
That is currently done by in user-space by adding a
uci config item into /etc/config/network
(More elegant solution might be setting it already in
preinit phase.)
Known issues:
* wifi firmware file may not get created on the first boot
after flashing on time to bring wifi normally up. Likely
the overlay jffs2 is not yet ready for creating the
firmware file. "wifi up" may still bring wifi up.
Wifi will work normally at subsequent boots.
* phy0 and phy1 may get assigned mixed, so that phy0 may
be the 5GHz radio instead of the normal 2.4GHz, and vice
versa for phy1. Does not happen always, but may happen.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[fix the wifi unit address in the dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Pisen WMM003N (sold under the name of Cloud Easy Power) is an
AR9331-based router and power bank combo device. The device uses a
stock firmware modified from OpenWRT for TP-Link TL-WR703N; however
some GPIO definition is different on this device with TL-WR703N. An
AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also
added, and the stock Flash/RAM configuration is 8MiB/64MiB.
The stock firmware is an old and heavily modified OpenWRT-based
firmware, which has telnetd defaultly open, and the root password is
"ifconfig" (quotation marks not included). The factory image format is
not known yet, however the stock firmware ships the OpenWRT's sysupgrade
command, and it can be used to install a newer firmware.
Due to the lack of the access to the STM8 embedded controller, the SD
slot is currently not usable (because it's muxed with the on-board USB
port) and the AXP PMIC cannot be monitored.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
This target is on 4.9 currently.
It seems the support for this old kernel never got dropped.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This router is called RE450 and the tl prefix was used to identify it
as a TP-Link device. Drop the tl prefix since we now have tplink in
dts and device name.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
In "brcm47xx: rework model detection" the file 01_detect was moved
to 01_network, therefore also update the warning message in case
everything fails.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
PLL for eth0 internal clock on ar913x is at 0x18050014
and AR913X_ETH0_PLL_SHIFT is 20 instead of 17
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add support for WNDR3700 and WNDR3700v2.
They share most things with WNDR3800.
Only device IDs and partition structure needs to be set.
Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has
also the NA version of the factory image.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prepare for addition of WNDR3700 and WNDR3700v2 by
separating the common parts into wndr3700.dtsi and
leaving just the device-specific things into wndr3800.dts
The three routers are identical except
* device IDs
* WNDR3700 (v1) has only 8 MB flash, while others have 16 MB.
Partition structure needs to be defined for each device.
* (WNDR3800 has 128 MB RAM, but RAM size is not in DTS)
Also separate the common parts of the image recipe.
(Drop also the initramfs recipe.)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The wholesale changes introduced in commit f9b8328 missed this DTS file
because it hadn't been merged yet. This patch brings it in line to match
the other mt7620a devices' DTS files.
Additionally, the Internet LED is now labeled correctly and set to unused
by default, since the WAN interface is not known in every configuration.
Using sysupgrade between images before and after this commit will require
the -F flag.
Tested-by: Rohan Murch <rohan.murch@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[drop internet led default setting]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the Netgear R6120, aka Netgear AC1200.
Specification:
- SoC: MediaTek MT7628 (580 MHz)
- Flash: 16 MiB
- RAM: 64 MiB
- Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E)
- LAN speed: 10/100
- LAN ports: 4
- WAN speed: 10/100
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600
To flash use nmrpflash with the provided factory.img.
Flashing via webinterface will not work, for now.
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
The kernel image of the at91-q5xr5 is getting too bing now and this is
breaking the build. Remove the image for the at91-q5xr5 from the build
to at least build images for the other devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- Qualcomm Atheros QCA9557
- 128 MB of RAM
- 16 MB of Flash
- 2.4/5 GHz wifi
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR2
2. Connect power cable to WN-AC1600DGR2 and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch copies over the MAC patching helper functions from lantiq's
target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
file.
Not all vendors bothered to write the correct MAC addresses for the
ath9k wifi into the calibration data. And while ath9k does have some
special dt-properties to extract the addresses from a fixed position,
there are still devices that require userspace to edit or modify
the caldata.
In my case, the MAC address for the Wi-Fi device is stored in an
unsorted key-value based "nvram" database and there's an existing
userspace tool to extract the data.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Bit 8/12 of reset controller which is marked as PHY_RESET/SWITCH_RESET
in datasheets will trigger either a reset for builtin switch or assert
an external ETH0_RESET_L/ETH1_RESET_L pin, which are usually connected
to external PHY/switch. None of them should be triggered every time an
interface is brought up in ethernet driver.
Remove PHY reset support from ag71xx and definition for them in dtsi.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros
QCA9558.
Ported from ar71xx target.
Specification:
- Qualcomm Atheros QCA9558
- 64 MB of RAM
- 16 MB of Flash
- 5x 10/100/1000 Ethernet
- QCA8337N
- 4x LEDs, 2x keys
- UART header on PCB
- Vcc, TX, RX, GND from LED side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Connect power cable to BHR-4GRV2 and turn on it
3. Access to "http://192.168.12.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新実行")
button
5. Wait ~120 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This adds PLL settings for the ethernet ports of the TP-Link TL-WR1043
v2/v3 and the Openmesh OM5P-AC-v2.
We also change the PLL-settings in the qca9557.dtsi to match the ones
used as default on the ar71xx target.
As of 4b9680f138 those devices have broken ethernet ports as the default
PLL settings defined in the QCA9557.dtsi are applied which are off for
those devices.
Signed-off-by: David Bauer <mail@david-bauer.net>
commit 4b9680f fixed pll settings and the correct pll set
by bootloader is overrided by value in qca9557.dtsi which
is incorrect for Archer C7 and breaks ethernet. Add pll
values for archer c7 to fix ethernet connection.
This individual pll tweak has been cherry picked from github pr 1260
which changes a couple of things in a single commit and should be
ideally split. This commit get archer v7 back and working.
Tested: archer c7 v2
Original combined commit authored by:
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
c7 fix only split out by:
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Changed default role of Orange Pi PC2 MSUB port to host (in dts)
Changed default function of Orange Pi PC2 power button to PWR_BTN
Signed-off-by: Antonio Silverio <menion@gmail.com>
CPU: H5 High Performance Quad-core 64-bit Cortex-A53
GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL
Memory: 1GB DDR3 (shared with GPU)
Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB)
Onboard Network: 1000M/100M Ethernet RJ45
USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode
role by default in DTS
Buttons: Power Button(SW4) Debug TTL
UART: ..DC-IN..
>[GND][RX][TX] ..HDMI..
Signed-off-by: Antonio Silverio <menion@gmail.com>
When checking the outcome of the PHY autonegotiation status, at803x
currently returns false in case the SGMII side is not established.
Due to a hardware-bug, ag71xx needs to fixup the SoCs SGMII side, which
it can't as it is not aware of the link-establishment.
This commit allows to ignore the SGMII side autonegotiation status to
allow ag71xx to do the fixup work.
Signed-off-by: David Bauer <mail@david-bauer.net>
The QCA955X is affected by a hardware bug which causes link-loss of the
SGMII link between SoC and PHY. This happens on change of link-state or
speed.
It is not really known what causes this bug. It definitely occurs when
using a AR8033 Gigabit Ethernet PHY.
Qualcomm solves this Bug in a similar fashion. We need to apply the fix
on a per-device base via platform-data as performing the fixup work will
break connectivity in case the SGMII interface is connected to a Switch.
This bug was first proposed to be fixed by Sven Eckelmann in 2016.
https://patchwork.ozlabs.org/patch/604782/
Based-on-patch-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds the ability to configure specific functions of the
at803x series ethernet-PHYs, which were previously configured
exclusively with the help of platform-data, via device-tree.
This is needed to fully support existing boards of the ar71xx platform.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport an upstream fix for a remotely exploitable TCP denial of service
flaw in Linux 4.9+.
The fixes are included in Linux 4.14.59 and later but did not yet end up in
version 4.9.118.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The QCA9557 dtsi is currently missing pll-handle and pll-regs for both
eth0 and eth1, therefore PLL settings won't be applied. This commit
fixes this behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
While finalizing support for the U7623 with 512MB, I made an embarresing
error and configured 1GB RAM for the board. I also forgot to move memory
from the dtsi and to the dts. This commit takes care of my mistakes.
While I am confessing my mistakes, I also note that I made a mistake in
the commit message of the initial U7623 commit. It is the .bin-file, and
not the .gz file that shall be sent to the device via tftp.
v1->v2:
* Remove redundant memory node (thanks Jonas Gorski)
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Including the tl-wdr3600 image build code just to overwrite most of it
doesn't make much sense and only makes it hard to read.
Furthermore, the tl-wdr4300 image will be marked as compatible with the
tl-wdr3600 this way.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The variables are used in image build recipes and need to be marked as
per devices vars to be stored individual per image define. Otherwise
the last defined variable will be used for all boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch did the following things:
1. Separate ath9k-leds out of gpio leds so that all other leds will work
before ath9k loded (e.g. during preinit/init stage).
2. Rename wps led to qss since that's how TP-Link mark it.
3. Rename LED prefix to tp-link because that dts is shared by many devices.
4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1.
(This will require a forced sysupgrade if you comes from
the previous wr740n v2 image.)
5. Remove SUPPORTED_DEVICES.
(tl-wr740n-v2 doesn't exist anywhere so it's useless.)
6. Add all WR741ND v1 clones found in ar71xx.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the same method for setting queue index pointers consistenly
throughout the source file.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This router is called Archer C7 and the tl was used to identify
TP-LINK. Since we have added tplink in dts/board name, the tl
prefix is useless now.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Change lan and it's LED to eth0
It's broken since c7c807cb8c
where I changed the dts but forgot to change default configurations.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
1. Swap eth0/eth1
Both devices are using AR9331, the builtin switch on AR9331 is
connected to gmac1 and gmac1 is named as eth1 in ath79.
PS: gmac1 is eth0 and gmac0 is eth1 in ar71xx because of the
reversed initialization order.
2. Fix the incorrect compatible string in dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
phy-handle is used to poll link status. They are useless when
we need fixed-link on these interfaces.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Jonas Gorski commented on the previous patch:
|This is actually the wrong fix and papers over an issue in one of our
|local patches.
|
|We intentionally allow regmap to be built as a module, see
|
|/target/linux/generic/hack-4.14/259-regmap_dynamic.patch
|[...]
|[The regulator code] optionally supports regmap thanks to the stubs
|provided if regmap is disabled - which breaks if you compile regmap
|as a module.
In order to mitigate this issue, this patch reverts the previous patch
and replaces the existing IS_ENABLED(CONFIG_REGMAP) with
IS_REACHABLE(CONFIG_REGMAP). This solves this particular issue as the
regulator code will now automatically fallback to the regmap stubs in
case the kmod-regmap module is enabled, but nothing else sets
CONFIG_REGMAP=y.
Note: There's still a potential issue that this patch doesn't solve:
If someone ever wants to make a OpenWrt kernel package for a
regulator module that requires the REGMAP feature for a target that
doesn't set CONFIG_REGMAP=y but has CONFIG_REGULATOR=y, the resulting
kmod-regulator-xyz package will not work on the target.
Luckily, there aren't any in-tree OpenWrt kernel module packages for
regulators at the moment. On the bright side: regmap is a critical
part nowadays and all new and upcoming architectures require it by
default. This will likely only ever be a problem for legacy targets
and devices that cannot afford to enable REGMAP.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
Fixes: d00913d121 ("kernel: modules: fix kmod-regmap")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To share mdio addr for IntPHY and ExtPHY,
as described in the documentation (MT7620_ProgrammingGuide.pdf).
(refer: http://download.villagetelco.org/hardware/MT7620/MT7620_ProgrammingGuide.pdf)
when port4 setup to work as gmac mode, dts like:
&gsw {
mediatek,port4 = "gmac";
};
we should set SYSCFG1.GE2_MODE==0x0 (RGMII).
but SYSCFG1.GE2_MODE may have been set to 3(RJ-45) by uboot/default
so we need to re-set it to 0x0
before this changes:
gsw: 4FE + 2GE may not work correctly and MDIO addr 4 cannot be used by ExtPHY
after this changes:
gsw: 4FE + 2GE works and MDIO addr 4 can be used by ExtPHY
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.
Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
This really simplifies debugging, if a package is not found or a feed is
not reachable, a proper stderr is printed. Currently it would only say
`_call_manifest` failed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Fix space vs. tabs issue and trainling whitespaces. Use C style
comments or drop the comments if they explain what is already to see in
the devicetree parameters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.
Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.
Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.
Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.
If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.
Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.
Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.
Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.
gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.
Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
Revert 290c54473e ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.
Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.
The correct MAC adress increments for this board are:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
Fixes: FS#408
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Linux headers on arm64 architectures contain references to common
arch/arm/ headers which were not bundled by the SDK so far.
Check if we're packing the SDK for an arm64 target and if we do, also
include arch/arm headers as well.
Fixes FS#1725.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It seems to have been missed when the patch was accepted.
Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The integrated SoC wifi will likely never be supported, and if,
it will go through DT with the sprom contents there.
Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
1) Add comments so it's clear why we did things; this may prevent
someone (e.g. me) from sinking time into fixing things that
aren't broken and/or were done for reason.
2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0.
3) Cosmetic reording of some code (tested) that makes the defintion
more clear.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The CR3000 stock firmware is now irrelevant as it required a now defunct
cloud service. Therefore only build images that use the entire flash
(overwriting stock firwmare-specific partitions that no longer matter),
previously called 'nocloud' images.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering. It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:
1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.
2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.
3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.
4) eth0 is wan and eth1 is lan (switch)
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Refreshed all patches
Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch
Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.
Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9
Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Bundle the usbip utility sources shipped with the Linux kernel tree in
order to allow the usbip packages from the package feed to build within
the OpenWrt SDK.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for
ARM64. Add this symbol to all ARM64 targets using kernel 4.14.
This mitigates CVE-2018-3639 on ARM64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.
Fixes: f791fb4af4 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch was wrongly removed by a kernel version bump to 4.9.105 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.
Fixes: 7dca1bae82 (kernel: bump to 4.9.105)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The previous round of fixes for the 82574 chip cause an issue with
emulated e1000e devices in VMware ESXi 6.5. It also contains changes
that are not strictly necessary. These patches fix the issues introduced
in the previous series, revert the unnecessary changes to avoid
unforeseen fallout, and avoid a case where interrupts can be missed.
The final two patches of this series are already in the kernel, so no
need to include them here.
Patchwork: https://patchwork.ozlabs.org/cover/881776/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This changes the DT binding's compatible property to
"ecoscentric,redboot-fis-partitions", removing the existing reference to
Red Hat.
Per the documentation hosted at eCosCentric's website, eCosCentric is
RedBoot's sole commercial maintainer since 2002, and the project has
been under the stewardship of the Free Software Foundation since 2008.
This also updates the property in the Inventel Livebox 1 .dts, the
binding's only current user.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
The OpenMesh A62 is a tri-band device (1x 2.4GHz, 2x 5GHz) with special
filters in front of the RX+TX paths to the 5GHz PHYs. These filtered
channel can in theory still be used by the hardware but the signal strength
is reduced so much that it makes no sense.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.
The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.
While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Add missing definitions for the orange WAN LED on the
TL-WR1043N(D) v4 and v5.
Change the name of a MAC address offset constant to
make it consistent with the format of the
existing constants.
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
- MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 57600 bps
Flash instruction using factory image:
1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list
This PR is based on the work of @fewckert[1] with slight improvements.
Add function `manifest` to show the manifest of the produced image,
before actually building it. The manifest contains an orderd list of
package name and version.
This is usefull to check package dependencies but also determine a
unique and reproducible image name before building the package. The
sysupgrade server[2] builds images on request with individual package
selection. To distignish between created images which contain differnt
packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the
manifest's content. So far the image was renamed afterwards as the
manifests content was unknown, however this corrupts the signed
sha256sums. This patch allows a clean solution as to dtermine the
manifest in advance and set the EXTRA_IMAGE_NAME accordingly.
[1]: https://github.com/lede-project/source/pull/1591
[2]: https://github.com/aparcar/attendedsysupgrade-server
Signed-off-by: Paul Spooren <mail@aparcar.org>
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB
Flash instruction:
- via web UI:
1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
2. Login to router and open the Advanced tab
3. Navigate to System Tools -> Firmware Upgrade
4. Upload firmware using the Manual Upgrade form
- via TFTP:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Keith Maika <keithm@aoeex.com>
This fixes:
drivers/mtd/redboot.c:299:34: error: array type has incomplete element type 'struct of_device_id'
Fixes: 5e8b4be531 ("kernel: add DT binding support to the mtd redboot parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
linux,part-probe should be avoided as its only supported with OpenWrt
downstream patch that is going to be dropped eventually.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.
Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.
As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.
Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.
Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
fixes FS#1034, squash fs images fails to boot because of missing ARM BCJ filter decoder
also activate squashf image creation
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.
Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.
This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.
Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This is required for the Traverse LS1043 family, we generate a FIT image
that works on all boards across the family. This is done by creating
multiple configurations that select the right DTB for the board.
The bootloader on these boards is configured to boot like this:
bootm $kernel_load#ls1043s
bootm $kernel_load#ls1043v
This is based on earlier work by Jason Wu for Zynq:
https://lists.openwrt.org/pipermail/openwrt-devel/2016-March/040460.html
Modified to add FDT load addresses and multiple configurations with DTB.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This is required on the Traverse LS1043 boards to support SFP
and xDSL plug-ins.
This will not be needed on kernel 4.14.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
In boards with fdt is impossible to use kmod-w1-gpio-custom.
w1-gpio-custom create platform structure for w1-gpio module,
but if board use fdt, data is ignored in w1-gpio probe.
This workaround fix the problem.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.
Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.
Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested on HC5661A and it now fixes the issue that when enabling sd card
in HC5661A, the wan and 3 lan ports will down.
Known issue:
- When enabling SD card support, the led light of system will down and the rest 2 lights keep working.
Signed-off-by: LoveSy <shana@zju.edu.cn>
There is another thing about crc to do when initialize SD card on
MT7628.
This commit is to fix this init issue.
Signed-off-by: LoveSy <shana@zju.edu.cn>
Qxwlan E750G v8 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (PoE support)
- 2x 10/100/1000 Mbps Ethernet
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
The driver is written in such a way that with a board defintion that
connects a fixed phy, mdio, and switch in a certain way, a kernel oops could
result because of lack of previously probed mdio bus.
This commit allows for easier debugging in this case by casting the
correct blame with serial console messages.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
It's a little noisier but makes it obvious when the ar7240 switch was
connected to the MDIO bus, and to which phy device (or the failure
to do so).
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
NB: Error only appears with ag71xx debug messages and dynamic printk
enabled. This is probably why no one has caught it before.
Previously phy probe debug messages used old (now wrong) functions
to get the phy name for printing. There was also the chance of
a NULL pointer in the event no phy_device was found.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
mdio bus isn't a standalone device on ar7240. (and maybe older SoCs?)
Use simple-mfd for ar7241 and later SoCs to get mdio1 ready before gmac0
For ar7240 and older chips, manually create platform device after
ag71xx_hw_init() in ag71xx_probe()to get mdio0 ready between
ag71xx_hw_init() and ag71xx_phy_connect().
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Allow specifying desired mdio clock frequency in dts.
Use default frequency around 5MHz for builtin switch and 2MHz for other mdio bus.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Remove mdio1 and phy1 handle. AR8327N is controlled through mdio0.
Add gmac-config for Archer C7.
Remove ucidef_set_interfaces_lan_wan. They can be determined by config_generate automatically.
The following are for adding support for WDR4900 v2/Archer C7 v1 and other
devices that shared the same machine file in ar71xx:
Move mtd partitions to archer-c7-v2.dts. Only Archer C7 v2 has 16M flash.
Flash on Archer C7 v1/TL-WDR4900 v2 is 8M.
Add label for wlan leds. The default trigger for archer c7/wdr4900 is different.
Move wlan5g led to archer-c7-v2.dts. 5G led on WDR4900 is connected to ar9380.
Move rfkill definition to archer-c7-v2.dts. There is no such a button on wdr4900 v2.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
enable mdio1 by default because mdio1 node is a subnode of eth1
and eth1 node is a "simple-mfd", which makes mdio1 disabled when
eth1 isn't enabled.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Most qca devices use 115200n8 as it's default uart baudrate.
Add 'chosen' node for qca953x like other SoCs in ath79 target.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Commit c7efc93 renamed controller name
to qca,ar9340-intc and added some functions but qca9533.dtsi was overlooked.
Correct the dtsi and adust it to the new format
Add gmac and correct reset for cascaded irq and build-in switch
Also add the reference clock to soc dtsi so we don't have to have it in every dts
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Remove switch reset definition
Fix gmac compatible string (We only need SW_PHY_SWAP and SW_PHY_ADDR_SWAP on qca953x so use ar9330-gmac instead of ar9340-gmac.)
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
gmac0 is always connected to switch phy4 and mdio1 is always needed.
So add phy handle for eth0 and enable mdio1 by default.
Move fixed-link for gmac1 from device dts to ar9331.dtsi because gmac1 is always connected to builtin switch.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Enable mdio1 by default because mdio1 is needed when eth1 is enabled.
PS: If a ar9341 device has only one port and you only want to use gmac0,
change compatible of gmac1 to "syscon", "simple-mfd" in dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch did several things:
1. Probe the builtin switch as a separated mdio device.
2. Register a separated mdio bus for builtin switch.
3. Use generic mdio read/write function instead of calling ag71xx_mdio_mii_read/write directly.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
We need to have mdio1 belonging to gmac1 initialized before gmac0.
Split it into a separated mdio device to get both mdios ready before probing gmac.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The builtin switch has it's initial valid mac address(00:00:01:00:00:00).
Since the builtin switch is an independent device, setting mac address of gmac1 to builtin switch isn't a good idea and this makes it impossilbe to split builtin switch apart as an independent platform device.
Remove these functions and apply default VLAN during initialization as a preparation for further driver splitting.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Only build images for straight OpenWrt (using all flash; wipes out
partitions that contain information only important for accessing a
now defunct cloud service with the stock firmware) since the stock
firmware is now irrelevant.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The wrong MAC addresses (from the point of view of the physical device
label) were being assigned to the wrong interfaces. Fix that.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
While the stock firmware and previous ar71xx versions of openwrt used the
single ethernet port as a DHCP client, for unmodified openwrt usage it
makes more sense to do the standard openwrt thing and make the ethernet
port a static lan with known address so that users can find the device on
the network more easily.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The Skydog cloud service no longer exists hence supporting going back
to stock firmware with cloud support is no longer applicable.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The reset button was incorrectly returning KEY_WPS_BUTTON as the key
code. We want KEY_RESTART., so make that fix.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The PCIe wireless MAC address address is better labelled as WMAC
than MAC to emphasize that it is for a wireless interface.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The CAP324 was an AP for a NaaS offering that is now defunct. While
previously supported in the ar71xx arch, there were some errata (to
be fixed shortly).
Notable differences from ar71xx support:
1) The method of getting the ath9k firmware for the PCIe 2ghz wifi has
changed (due to changes in how the arch handles this), since this device
doesn't use the EEPROM except to get the MAC address of the wifi.
2) /etc/config/wireless will need to be regenerated as the path(s) to
the wireless device(s) have changed.
3) ath79 OpenWrt firmware no longer supports build an image that allows
reverting to stock firmware (as the cloud service no longer exists, the
stock firmware is useless), instead using all of the flash for image and
overlay (less u-boot/env and art).
4) Initial network config treats the ethernet port as a Lan port with
the standard default address (192.168.1.1 unless changed in .config
--e.g. via menuconfig) instead of using DHCP (this was the default for
the stock firmware, however for openwrt use this is rather confusion and
counter-productive as the user has a harder time finding the device on
the network.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Add ath79 arch support for PowerCloud Systems CR5000. Previously
supported under ar71xx (however there are some errors in that support;
to be fixed shortly).
Info:
* This board is based on the Atheros DB120 reference design, but doesn't
use the on-board switch. Instead it attachs GMAC0 to an AR8327 switch.
* It only uses GMAC0 and the WAN is simply a VLAN in the stock firmware.
* It has 64MB RAM and 8MB flash.
* In the dts version we get rid of using 'open-drain' for the AR8327
LED controls.
* As with the platform data version we disable JTAG as this conflicts
with one of the pair of GPIO's required for the power/status LED
(GPIO2 and GPIO4 are used for this LED).
* The pcie card wifi has an EEPROM but gets it's MAC address from
the ART partition.
* The SoC wifi (2.4 GHz) is all from the ART.
* The USB is support comes from the SoC.
NB. This is actually an AR9342 rather than AR9344 but we use the 9344
definitions because there are no relevant differences for this board.
NB: Building only images that don't support reverting to the old
cloud-based firmware as the Skydog cloud service for the CR5000 no
longer exists.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
81d446b045 introduced incomplete
support for this device.
This patch attempts to correct the situation based on OEM source
code.
LED1-3 are GSM mode on OFW (2G/3G/4G) hence unassigned here.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: David Ehrmann <ehrmann@gmail.com>
The active_low flag was missing for the user LED. This LED is open drain
(confirmed in OEM source) and open drain only makes sense for active low
GPIOs.
The two wireless LEDs mentioned in the comments are also #defined for
future reference.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.
Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.
This patch fixes these issues and renames the corresponding #defines for
clarity
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The gpios that control power toggle for USB on the RouterBOARD devices
are active low _off_ switches.
When they are active (low), power is off. When they are inactive
(high), power is on.
Rename GPIO defines, set gpios to GPIOF_ACTIVE_LOW for consistency and
reflect their true action in the display name. This brings openwrt code
in line with OEM.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
convert the usb and both sata port power related gpio-hogs to
what they really are: fixed-regulators.
The ethernet phy-reset gpio-hog is replaced by a proper
upstream (4.15+) reset-gpios property in the mdio-node.
So this will work eventually.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
The MBL's rootfs.img.gz image is generated in much the same way.
Hence this patch preemptively splits the rootfs.img.gz image into
a sysupgrade and a factory image.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for squashfs as the root filesystem.
advantages:
- migrate from a existing -ext4 installation and back
with the sysupgrade utility
- existing partition layout will not be lost during switch
- slightly smaller image size as compared to the -ext4 image.
disadvantages:
- needs f2fs + tools. This is because fstools rootdisk.c decides based
on the partition size (currently root partitions > 100 MiB) f2fs is
used as the rootfs_data filesystem.
- rootfs_data is placed into the rootfs partition after the squashfs.
This makes it difficult for tools that expect a /dev/sda${X} device.
It also makes it difficult for data recovery tools as they might not
expect to find a embedded partition or will be slightly confused.
... or will not support f2fs.
For people with existing build configurations: make sure to include mkf2fs
and f2fsck packages into the image. Otherwise the new -squashfs image will
only boot from the ram-overlay.
Note:
All overlay data (configurations/all installed packages/...) will be
placed in inside the rootfs partition (i.e. /dev/sda2) just after the
squashfs image.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It was present as 4.4 compatibility, but since we now use 4.9 or later
with the new upstream solution, we don't need it anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This includes Linksys EA9500 support, BCM53573 timer fix and
upstream-ready partitions patch that replaces two downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
USB 3.0 PHY is attached to the MDIO bus and should be supported
(accessed) as a MDIO device. This wasn't known initially which resulted
in writing driver that was working with MDIO bus (using some magic
values) without knowing it.
This commit updates DT to properly describe MDIO & USB 3.0 PHY and
enables required kernel drivers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is a new & warm feature that allows nesting partiitons in DT and
mixing their types (e.g. static vs. dynamic). It's very useful for
boards that have most partitions static but some of them require extra
parsing (e.g. a "firmware" partition).
It's required to successfully backport support for new devices using
that new syntax in their DT files.
Since brcm63xx has a custom alternative patch the upstream one is being
reverted for it. The plan is to make brcm63xx use the upstream
implementation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The OCEDO Raccoon only has one ethernet port, but currently uci sections
for WAN and LAN are created.
Additionally, newer versions of the devices U-Boot (units with SteelWRT)
set the kernel-cmdline and therefore overwrite the partition-layout.
We fix this by overwriting the cmdline supplied by the bootloader.
Signed-off-by: David Bauer <mail@david-bauer.net>
The get_status_led() function was removed due to the convertion to dts
alias based status led.
Since we don't need the boardname any longer, the functions.sh include
isn't required any more.
Fixes: c9c4b2116c ("ramips: Use dts alias based status led")
Signed-off-by: Mathias Kresin <dev@kresin.me>
With a10a204aab ("kernel: make ubi auto-attach check for a tar file
magic") the check for the magic was added without considering a failing
mtd_read(). If the read fails, no check is done and the mount code is
called straight away.
Failing with an error message for such cases seems to me the cleaner way,
as it would allow to spot hidden/workaround issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The first block(s) of the ubi mtd device might be bad. We need to take
care on our own to skip the bad block(s) and read the next one(s).
Don't treat recoverable read errors as fatal and check for the UBI magic
if the data of a block could be recovered using ECC or similar.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the put_mtd_device() called on multiple error conditions to a goto
label to use it later for more error conditions.
The early return on failed open of the mtd device and mismatching mtd
type allows to get rid of one level of indentation. By jumping to the
cleanup code, a refcount bug is fixed for the wrong flash type condition.
While at it, make clear that we only check for the UBI magic if the read
from flash was successful.
Signed-off-by: Mathias Kresin <dev@kresin.me>
By takimata:
"Come to think of it, an MBL Single board boots up just fine on an
MBL Duo image, and the MBL Single board identifies completely
identical to the MBL Duo
(Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB).
I wonder if there is any downside to just using the MBL Duo firmware
on a MBL Single. I wonder if the two firmwares could even be unified."
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All these devices share the exact same image format.
The usb3 kmod is added for the rbm11g, as the rbm11g has a mini-pcie
slot like its bigger sibling. The usb kmod is necessary for
usb-over-pcie support, which is mandatory for a lot of LTE modules.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.
Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info
LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)
The Fon LED is labeled as internet in avm gpl sources.
Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)
Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC
PCIe
GPIO#21: reset (active low)
Installation:
To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
ftp> quote REBOOT
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Use of_mdiobus_register() to pass the ethernet phy node to the phy
drivers. This is needed for the at8030 phy driver which needs to know
the GPIO which is connected to the ar8030 reset pin.
This driver expects a child in gsw/etop node named "mdio-bus", which has
the ethernet phys defined:
&gsw {
phy-mode = "rmii";
phy-handle = <&phy0>;
mtd-mac-address = <&ath9k_cal 0xa91>;
mtd-mac-address-increment = <(-2)>;
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
};
};
};
Fallback to mdiobus_register() if no mdio-bus child node exists. This
way we don't need to touch all xway dts files, for which we don't know
the actual address on the mdio bus.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
The mac address for the 2.4 wireless need to be decremented by one.
Correct MAC adress increments for this board are:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Drop the parallel-unsafe custom Build/dtb macro and use the .dtb artifacts
produced by the generic image build code.
Also remove unused .dtb references in the mt7623 subtarget.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
F9K1115v2 has a kernel partition size of 1408 kB.
Since kernel 4.9.x+ the kernel image for this device compiled had exceeded
the kernel partition size limit and thus failing size check.
The kernel image generated for this device
under ar71xx tiny target is 1329.67 kB < 1408 kB.
Signed-off-by: Kin Chan <kcchan1@outlook.com>
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD
Specifications:
* SoC: Qualcomm QCA9533 (650MHz)
* RAM: 32MiB
* Storage: 16MiB SPI NOR flash
* Ethernet: 3x100M
* Wireless: QCA9533 built-in, dual-chain 802.11b/g/n
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its Internet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Now connect the board via either of its LAN ports (2 or 3).
6. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
7. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
8. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
SOC: BCM63168 (BMIPS4350 V8.0 @400MHz)
Flash size: 16 MiB
RAM size: 128 MiB
Heavily based on patch for OpenWRT Chaos Chalmer.
Original patch and more info can be found at:
https://openwrt.org/toh/sky/sr102
Known issues:
- Wireless and ADSL modem are not working.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" could very
well fix the freezes that have been reported on the forum by
@ticerex and @takimata.
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/46>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The code has some remaining issues that cause ethernet hangs, so
disable it for now until we can get it fixed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The line that produces factory image was accidentally left by me while
testing before inital commit.
I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).
I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.
So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Extend the small_flash feature to disable swap, core dumps, and
kernel debug info, and change the squashfs block size to 1024KiB.
Also change squashfs fragment cache to 2 for small_flash to ease memory
usage.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add a new config option to allow to select the default compile
optimization level for the kernel.
Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.
Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.
Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.
Exceptions to the above are:
- lantiq, where the optimization for size is only required for the
xway_legacy subtarget but was set for the whole target
- mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
plenty of space and an optimization for size doesn't make much sense
- rb532, which has 128MByte flash
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move boards to the tiny subtarget which break the build if the kernel is
set to "Optimize for performance".
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the latest version of u-boot (2018.05) there was a swith to
Hush shell for ARC AXS10x boards(arc770/archs38):
commit 9249d74781e1 ("ARC: AXS10x: Enable hush shell").
In Hush shell using "$()" to declare envitonment variables is forbidden,
instead of this "${}" need to be used.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
The changed applied to BananaPi R2 in upstream commit c0b0d540db1a,
which was backported to 4.14 in 4.14.53, is also required for the U7623.
Without updating the memory node, the board refuses to boot.
Fixes: d0839e020d ("kernel: bump 4.14 to 4.14.53")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align
Let the MTD core take care of both
Fixes messages like these:
[ 102.820541] Data buffer not 16 bytes aligned: 87daf08c
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Newer kernels have a patch that implements compatible functionality
directly. Adjust the attribute of our own patch in preparation for
dropping it later
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rereshed all patches
Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.
This fixes UBI support for devices that have kernel flashed on partition
with a bad block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit adds support for the OCEDO Raccoon
SOC: Atheros AR9344
RAM: 128MB
FLASH: 16MiB
WLAN1: AR9344 2.4 GHz 802.11bgn 2x2
WLAN2: AR9382 5 GHz 802.11an 2x2
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
NOTE: The U-Boot won't boot with the serial attached.
Boot the device without serial attached and attach it
after 3 seconds.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_USB_MTU3 is not visible for the mediatek target by default, but
only when CONFIG_USB_GADGET is set. This will config option will be
remove with when running "make kernel_oldconfig", move this option to
the generic config to prevent this.
This fixes the build of the mt7623 subtarget of the mediatek target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shrink the tiny kernel by moving all switch and ethernet phy drivers to
the generic kernel config instead of the target kernel config.
All boards in the tiny and nand target are either ar7240 or ar9331 based,
which don't support external xMII and therefore no external ethernet phy
can be connected. None of the boards uses a realtek switch either.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
