ath79: add support for I-O DATA WN-AC1600DGR2

I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- Qualcomm Atheros QCA9557
- 128 MB of RAM
- 16 MB of Flash
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 3T3R (QCA9880)
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR2
2. Connect power cable to WN-AC1600DGR2 and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi 2018-08-10 09:07:53 +09:00 committed by Mathias Kresin
parent 97de133368
commit a6369206fe
7 changed files with 257 additions and 9 deletions

View file

@ -264,6 +264,11 @@ define Build/openmesh-image
"$(call param_get_default,rootfs,$(1),$@)" "rootfs"
endef
define Build/senao-header
$(STAGING_DIR_HOST)/bin/mksenaofw $(1) -e $@ -o $@.new
mv $@.new $@
endef
define Build/sysupgrade-tar
sh $(TOPDIR)/scripts/sysupgrade-tar.sh \
--board $(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)) \

View file

@ -46,6 +46,11 @@ ath79_setup_interfaces()
glinet,ar300m)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
iodata,wn-ac1600dgr2|\
pcs,cr5000)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
;;
netgear,wndr3800)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
@ -66,10 +71,6 @@ ath79_setup_interfaces()
"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
ucidef_set_interface_wan "eth0"
;;
pcs,cr5000)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
;;
phicomm,k2t)
ucidef_add_switch "switch0" \
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
@ -152,6 +153,10 @@ ath79_setup_macs()
lan_mac=$(mtd_get_mac_text "caldata" 65440)
wan_mac=$(mtd_get_mac_text "caldata" 65460)
;;
iodata,wn-ac1600dgr2)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
;;
phicomm,k2t)
lan_mac=$(k2t_get_mac "lan_mac")
wan_mac=$(k2t_get_mac "wan_mac")

View file

@ -95,6 +95,17 @@ ath9k_patch_fw_mac_crc() {
board=$(board_name)
case "$FIRMWARE" in
"ath9k-eeprom-ahb-18100000.wmac.bin")
case $board in
iodata,wn-ac1600dgr2)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
esac
;;
"ath9k-eeprom-pci-0000:00:00.0.bin")
case $board in
avm,fritz300e)

View file

@ -87,6 +87,10 @@ board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
iodata,wn-ac1600dgr2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
;;
ocedo,koala)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)

View file

@ -0,0 +1,216 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca9557.dtsi"
/ {
compatible = "iodata,wn-ac1600dgr2", "qca,qca9557";
model = "I-O DATA WN-AC1600DGR2";
aliases {
led-status = &power;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
leds {
compatible = "gpio-leds";
power: power {
label = "wn-ac1600dgr2:green:power";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
copy {
label = "wn-ac1600dgr2:green:copy";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
default-state = "off";
};
eco {
label = "wn-ac1600dgr2:green:eco";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
default-state = "off";
};
wlan5g {
label = "wn-ac1600dgr2:green:wlan5g";
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
wlan2g {
label = "wn-ac1600dgr2:green:wlan2g";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy1tpt";
};
notification {
label = "wn-ac1600dgr2:amber:notification";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
default-state = "off";
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
button_eco {
label = "eco";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
debounce-interval = <60>;
};
auto {
label = "auto";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
button_copy {
label = "copy";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
debounce-interval = <60>;
};
wps {
label = "wps";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
reset {
label = "reset";
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
router {
label = "router";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x030000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x030000 0x010000>;
read-only;
};
partition@40000 {
label = "firmware";
reg = <0x040000 0xe50000>;
};
partition@e90000 {
label = "manufacture";
reg = <0xe90000 0x100000>;
read-only;
};
partition@f90000 {
label = "backup";
reg = <0xf90000 0x010000>;
read-only;
};
partition@fa0000 {
label = "storage";
reg = <0xfa0000 0x050000>;
read-only;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
qca,ar8327-initvals = <
0x04 0x87600000 /* PORT0 PAD MODE CTRL */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
};
&eth0 {
status = "okay";
pll-data = <0x56000000 0x00000101 0x00001616>;
phy-handle = <&phy0>;
};
&pcie1 {
status = "okay";
wifi@0,0 {
compatible = "pci168c,003c";
reg = <0x0000 0 0 0 0>;
qca,no-eeprom;
};
};
&uart {
status = "okay";
};
&usb_phy0 {
status = "okay";
};
&usb0 {
status = "okay";
};
&wmac {
status = "okay";
qca,no-eeprom;
};

View file

@ -67,6 +67,18 @@ define Device/glinet_ar300m_nor
endef
TARGET_DEVICES += glinet_ar300m_nor
define Device/iodata_wn-ac1600dgr2
ATH_SOC := qca9557
DEVICE_TITLE := I-O DATA WN-AC1600DGR2
IMAGE_SIZE := 14656k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
senao-header -r 0x30a -p 0x60 -t 2 -v 200
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k ath10k-firmware-qca988x
endef
TARGET_DEVICES += iodata_wn-ac1600dgr2
define Device/ocedo_koala
ATH_SOC := qca9558
DEVICE_TITLE := OCEDO Koala

View file

@ -108,11 +108,6 @@ define Build/poray-header
mv $@.new $@
endef
define Build/senao-header
$(STAGING_DIR_HOST)/bin/mksenaofw $(1) -e $@ -o $@.new
mv $@.new $@
endef
define Build/seama
$(STAGING_DIR_HOST)/bin/seama -i $@ $(1)
mv $@.seama $@