ar71xx:add support for E750G v8

Qxwlan E750G v8 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (PoE support)
 - 2x 10/100/1000 Mbps Ethernet
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
This commit is contained in:
张鹏 2018-07-17 18:14:25 +08:00 committed by John Crispin
parent ac03d51a3f
commit 53a4502013
12 changed files with 194 additions and 2 deletions

View file

@ -67,7 +67,7 @@ cpe870|\
dr531|\
e600g-v2|\
e600gac-v2|\
e750a-v2)
e750a-v4)
ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0"
ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1"
@ -373,7 +373,8 @@ e1700ac-v2)
ucidef_set_led_usbdev "usb" "USB" "$board:green:usb" "1-1"
ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2g" "phy1tpt"
;;
e558-v2)
e558-v2|\
e750g-v8)
ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
;;
esr900)

View file

@ -385,6 +385,7 @@ ar71xx_setup_interfaces()
ucidef_add_switch_attr "switch0" "enable" "false"
;;
e1700ac-v2|\
e750g-v8|\
unifiac-pro|\
xd3200)
ucidef_add_switch "switch0" \

View file

@ -27,6 +27,7 @@ get_status_led() {
e558-v2|\
e600gac-v2|\
e750a-v4|\
e750g-v8|\
eap120|\
minibox-v1|\
packet-squirrel|\

View file

@ -687,6 +687,9 @@ ar71xx_board_detect() {
*"E750A v4")
name="e750a-v4"
;;
*"E750G v8")
name="e750g-v8"
;;
*"EAP120")
name="eap120"
tplink_pharos_board_detect "$(tplink_pharos_get_model_string | tr -d '\r')"

View file

@ -254,6 +254,7 @@ platform_check_image() {
e600g-v2|\
e600gac-v2|\
e750a-v4|\
e750g-v8|\
ebr-2310-c1|\
ens202ext|\
epg5000|\

View file

@ -104,6 +104,7 @@ CONFIG_ATH79=y
# CONFIG_ATH79_MACH_E558_V2 is not set
# CONFIG_ATH79_MACH_E600G_V2 is not set
# CONFIG_ATH79_MACH_E750A_V4 is not set
# CONFIG_ATH79_MACH_E750G_V8 is not set
# CONFIG_ATH79_MACH_EAP120 is not set
# CONFIG_ATH79_MACH_EAP300V2 is not set
# CONFIG_ATH79_MACH_EAP7660D is not set

View file

@ -744,6 +744,17 @@ config ATH79_MACH_E750A_V4
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_E750G_V8
bool "Qxwlan E750G v8 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ESR900
bool "EnGenius ESR900 board support"
select SOC_QCA955X

View file

@ -115,6 +115,7 @@ obj-$(CONFIG_ATH79_MACH_E1700AC_V2) += mach-e1700ac-v2.o
obj-$(CONFIG_ATH79_MACH_E558_V2) += mach-e558-v2.o
obj-$(CONFIG_ATH79_MACH_E600G_V2) += mach-e600g-v2.o
obj-$(CONFIG_ATH79_MACH_E750A_V4) += mach-e750a-v4.o
obj-$(CONFIG_ATH79_MACH_E750G_V8) += mach-e750g-v8.o
obj-$(CONFIG_ATH79_MACH_EAP120) += mach-eap120.o
obj-$(CONFIG_ATH79_MACH_EAP300V2) += mach-eap300v2.o
obj-$(CONFIG_ATH79_MACH_EAP7660D) += mach-eap7660d.o

View file

@ -0,0 +1,151 @@
/*
* Qxwlan E750G v8 board support
*
* Copyright (C) 2017 Peng Zhang <sd20@qxwlan.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include <linux/phy.h>
#include <linux/platform_device.h>
#include <linux/ath9k_platform.h>
#include <linux/ar8216_platform.h>
#include <asm/mach-ath79/ar71xx_regs.h>
#include "common.h"
#include "pci.h"
#include "dev-ap9x-pci.h"
#include "dev-gpio-buttons.h"
#include "dev-eth.h"
#include "dev-usb.h"
#include "dev-leds-gpio.h"
#include "dev-m25p80.h"
#include "dev-spi.h"
#include "dev-wmac.h"
#include "machtypes.h"
#define E750G_V8_GPIO_LED_SYS 14
#define E750G_V8_GPIO_LED_DS20 15
#define E750G_V8_GPIO_LED_DS10 20
#define E750G_V8_GPIO_LED_WLAN 21
#define E750G_V8_GPIO_BTN_RESET 12
#define E750G_V8_KEYS_POLL_INTERVAL 20 /* msecs */
#define E750G_V8_KEYS_DEBOUNCE_INTERVAL (3 * E750G_V8_KEYS_POLL_INTERVAL)
static struct gpio_led e750g_v8_leds_gpio[] __initdata = {
{
.name = "e750g-v8:green:system",
.gpio = E750G_V8_GPIO_LED_SYS,
.active_low = 1,
},
{
.name = "e750g-v8:green:ds10",
.gpio = E750G_V8_GPIO_LED_DS10,
.active_low = 1,
},
{
.name = "e750g-v8:green:ds20",
.gpio = E750G_V8_GPIO_LED_DS20,
.active_low = 1,
},
{
.name = "e750g-v8:green:wlan",
.gpio = E750G_V8_GPIO_LED_WLAN,
.active_low = 1,
},
};
static struct gpio_keys_button e750g_v8_gpio_keys[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = E750G_V8_KEYS_DEBOUNCE_INTERVAL,
.gpio = E750G_V8_GPIO_BTN_RESET,
.active_low = 1,
},
};
static const struct ar8327_led_info e750g_v8_leds_qca8334[] = {
AR8327_LED_INFO(PHY1_0, HW, "e750g-v8:green:lan"),
AR8327_LED_INFO(PHY2_0, HW, "e750g-v8:green:wan"),
};
static struct ar8327_pad_cfg e750g_v8_ar8327_pad0_cfg = {
.mode = AR8327_PAD_MAC_RGMII,
.txclk_delay_en = true,
.rxclk_delay_en = true,
.txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
.mac06_exchange_dis = true,
};
static struct ar8327_led_cfg e750g_v8_ar8327_led_cfg = {
.led_ctrl0 = 0x00000000,
.led_ctrl1 = 0xc737c737,
.led_ctrl2 = 0x00000000,
.led_ctrl3 = 0x00c30c00,
.open_drain = true,
};
static struct ar8327_platform_data e750g_v8_ar8327_data = {
.pad0_cfg = &e750g_v8_ar8327_pad0_cfg,
.port0_cfg = {
.force_link = 1,
.speed = AR8327_PORT_SPEED_1000,
.duplex = 1,
.txpause = 1,
.rxpause = 1,
},
.led_cfg = &e750g_v8_ar8327_led_cfg,
.leds = e750g_v8_leds_qca8334,
.num_leds = ARRAY_SIZE(e750g_v8_leds_qca8334),
};
static struct mdio_board_info e750g_v8_mdio0_info[] = {
{
.bus_id = "ag71xx-mdio.0",
.phy_addr = 0,
.platform_data = &e750g_v8_ar8327_data,
},
};
static void __init e750g_v8_setup(void)
{
u8 *mac = (u8 *) KSEG1ADDR(0x1f050400);
u8 *art = (u8 *) KSEG1ADDR(0x1f061000);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(e750g_v8_leds_gpio),
e750g_v8_leds_gpio);
ath79_register_gpio_keys_polled(-1, E750G_V8_KEYS_POLL_INTERVAL,
ARRAY_SIZE(e750g_v8_gpio_keys),
e750g_v8_gpio_keys);
mdiobus_register_board_info(e750g_v8_mdio0_info,
ARRAY_SIZE(e750g_v8_mdio0_info));
ath79_register_mdio(0, 0x0);
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0 |
AR934X_ETH_CFG_SW_ONLY_MODE);
/* GMAC0 is connected to an AR8327 switch */
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ath79_eth0_data.phy_mask = BIT(0);
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
ath79_eth0_pll_data.pll_1000 = 0x06000000;
ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
ath79_register_eth(0);
ath79_register_pci();
ath79_register_usb();
ath79_register_wmac(art, NULL);
}
MIPS_MACHINE(ATH79_MACH_E750G_V8, "E750G-V8", "Qxwlan E750G v8",
e750g_v8_setup);

View file

@ -109,6 +109,7 @@ enum ath79_mach_type {
ATH79_MACH_E600G_V2, /* Qxwlan E600G v2 */
ATH79_MACH_E600GAC_V2, /* Qxwlan E600GAC v2 */
ATH79_MACH_E750A_V4, /* Qxwlan E750A v4 */
ATH79_MACH_E750G_V8, /* Qxwlan E750G v8 */
ATH79_MACH_EAP120, /* TP-LINK EAP120 */
ATH79_MACH_EAP300V2, /* EnGenius EAP300 v2 */
ATH79_MACH_EAP7660D, /* Senao EAP7660D */

View file

@ -76,6 +76,7 @@ CONFIG_ATH79_MACH_E2100L=y
CONFIG_ATH79_MACH_E558_V2=y
CONFIG_ATH79_MACH_E600G_V2=y
CONFIG_ATH79_MACH_E750A_V4=y
CONFIG_ATH79_MACH_E750G_V8=y
CONFIG_ATH79_MACH_EAP120=y
CONFIG_ATH79_MACH_EAP300V2=y
CONFIG_ATH79_MACH_EAP7660D=y

View file

@ -403,6 +403,25 @@ define Device/e750a-v4-8M
endef
TARGET_DEVICES += e750a-v4-8M
define Device/e750g-v8-16M
DEVICE_TITLE := Qxwlan E750G v8 (16MB flash)
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 -swconfig
BOARDNAME := E750G-V8
SUPPORTED_DEVICES := e750g-v8
IMAGE_SIZE := 15936k
MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(pri-data)ro,64k(art),-(firmware)
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
endef
TARGET_DEVICES += e750g-v8-16M
define Device/e750g-v8-8M
$(Device/e750g-v8-16M)
DEVICE_TITLE := Qxwlan E750G v8 (8MB flash)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += e750g-v8-8M
define Device/ew-balin
DEVICE_TITLE := Embedded Wireless Balin Platform
DEVICE_PACKAGES := kmod-usb-core kmod-usb-chipidea