openwrtv4/target/linux/ramips/base-files/lib/ramips.sh

602 lines
7.7 KiB
Bash
Raw Normal View History

#!/bin/sh
#
# Copyright (C) 2010-2013 OpenWrt.org
#
RAMIPS_BOARD_NAME=
RAMIPS_MODEL=
ramips_board_detect() {
local machine
local name
machine=$(awk 'BEGIN{FS="[ \t]+:[ \t]"} /machine/ {print $2}' /proc/cpuinfo)
case "$machine" in
*"3G150B")
name="3g150b"
;;
*"3G300M")
name="3g300m"
;;
*"3g-6200n")
name="3g-6200n"
;;
*"3g-6200nl")
name="3g-6200nl"
;;
*"A5-V11")
name="a5-v11"
;;
*"Ai-BR100")
name="ai-br100"
;;
*"Air3GII")
name="air3gii"
;;
*"ALL0239-3G")
name="all0239-3g"
;;
*"ALL0256N")
name="all0256n"
;;
*"ALL5002")
name="all5002"
;;
*"ALL5003")
name="all5003"
;;
*"AR670W")
name="ar670w"
;;
*"AR725W")
name="ar725w"
;;
*"ASL26555")
name="asl26555"
;;
*"ATP-52B")
name="atp-52b"
;;
*"AWAPN2403")
name="awapn2403"
;;
*"AWM002 EVB")
name="awm002-evb"
;;
*"AWM003 EVB")
name="awm003-evb"
;;
*"BC2")
name="bc2"
;;
*"BR-6425")
name="br-6425"
;;
*"BR-6475nD")
name="br-6475nd"
;;
*"Broadway")
name="broadway"
;;
*"C20i")
name="c20i"
;;
*"C50")
name="c50"
;;
*"Carambola")
name="carambola"
;;
*"CF-WR800N")
name="cf-wr800n"
;;
*"CS-QR10")
name="cs-qr10"
;;
*"CY-SWR1100")
name="cy-swr1100"
;;
*"D105")
name="d105"
;;
*"DAP-1350")
name="dap-1350"
;;
*"DB-WRT01")
name="db-wrt01"
;;
*"DCH-M225")
name="dch-m225"
;;
*"DCS-930")
name="dcs-930"
;;
*"DCS-930L B1")
name="dcs-930l-b1"
;;
*"DIR-300 B1")
name="dir-300-b1"
;;
*"DIR-300 B7")
name="dir-300-b7"
;;
*"DIR-320 B1")
name="dir-320-b1"
;;
*"DIR-600 B1")
name="dir-600-b1"
;;
*"DIR-600 B2")
name="dir-600-b2"
;;
*"DIR-610 A1")
name="dir-610-a1"
;;
*"DIR-615 D")
name="dir-615-d"
;;
*"DIR-615 H1")
name="dir-615-h1"
;;
*"DIR-620 A1")
name="dir-620-a1"
;;
*"DIR-620 D1")
name="dir-620-d1"
;;
*"DIR-645")
name="dir-645"
;;
*"DIR-810L")
name="dir-810l"
;;
*"DIR-860L B1")
name="dir-860l-b1"
;;
*"Dovado Tiny AC")
name="tiny-ac"
;;
*"DuZun DM06")
name="duzun-dm06"
;;
*"E1700")
name="e1700"
;;
*"ESR-9753")
name="esr-9753"
;;
*"EX2700")
name="ex2700";
;;
*"F5D8235 v1")
name="f5d8235-v1"
;;
*"F5D8235 v2")
name="f5d8235-v2"
;;
*"F7C027")
name="f7c027"
;;
*"FireWRT")
name="firewrt"
;;
*"Fonera 2.0N")
name="fonera20n"
;;
*"FreeStation5")
name="freestation5"
;;
*"GL-MT300A")
name="gl-mt300a"
;;
*"GL-MT300N")
name="gl-mt300n"
;;
*"GL-MT750")
name="gl-mt750"
;;
*"HC5661")
name="hc5661"
;;
*"HC5761")
name="hc5761"
;;
*"HC5861")
name="hc5861"
;;
*"HG255D")
name="hg255d"
;;
*"HLK-RM04")
name="hlk-rm04"
;;
*"HPM")
name="hpm"
;;
*"HT-TM02")
name="ht-tm02"
;;
*"HW550-3G")
name="hw550-3g"
;;
*"IP2202")
name="ip2202"
;;
*"JHR-N805R")
name="jhr-n805r"
;;
*"JHR-N825R")
name="jhr-n825r"
;;
*"JHR-N926R")
name="jhr-n926r"
;;
*"M3")
name="m3"
;;
*"M4")
name="m4"
;;
*"MediaTek LinkIt Smart 7688")
linkit="$(dd bs=1 skip=1024 count=12 if=/dev/mtd2 2> /dev/null)"
if [ "${linkit}" = "LINKITS7688D" ]; then
name="linkits7688d"
RAMIPS_MODEL="${machine} DUO"
else
name="linkits7688"
fi
;;
*"Memory 2 Move")
name="m2m"
;;
*"Mercury MAC1200R v2")
name="mac1200rv2"
;;
*"MicroWRT")
name="microwrt"
;;
*"MiniEMBPlug")
name="miniembplug"
;;
*"MiniEMBWiFi")
name="miniembwifi"
;;
*"MiWiFi Mini")
name="miwifi-mini"
;;
*"MiWiFi Nano")
name="miwifi-nano"
;;
*"MLW221")
name="mlw221"
;;
*"MLWG2")
name="mlwg2"
;;
*"MOFI3500-3GN")
name="mofi3500-3gn"
;;
*"MPR-A1")
name="mpr-a1"
;;
*"MPR-A2")
name="mpr-a2"
;;
*"MR-102N")
name="mr-102n"
;;
*"MT7620a + MT7530 evaluation"*)
name="mt7620a_mt7530"
;;
*"MT7620a V22SG"*)
name="mt7620a_v22sg"
;;
*"MT7621 evaluation"*)
name="mt7621"
;;
*"MT7628AN evaluation"*)
name="mt7628"
;;
*"MT7688 evaluation"*)
name="mt7688"
;;
*"MZK-750DHP")
name="mzk-750dhp"
;;
*"MZK-DP150N")
name="mzk-dp150n"
;;
*"MZK-EX300NP")
name="mzk-ex300np"
;;
*"MZK-EX750NP")
name="mzk-ex750np"
;;
*"MZK-W300NH2"*)
name="mzk-w300nh2"
;;
*"MZK-WDPR"*)
name="mzk-wdpr"
;;
*"NA930")
name="na930"
;;
*"NBG-419N")
name="nbg-419n"
;;
*"NBG-419N v2")
name="nbg-419n2"
;;
*"Newifi-D1")
name="newifi-d1"
;;
*"NCS601W")
name="ncs601w"
;;
*"NixcoreX1")
name="nixcore-x1"
;;
*"NW718")
name="nw718"
;;
*"OY-0001")
name="oy-0001"
;;
*"PBR-D1")
name="pbr-d1"
;;
*"PBR-M1")
name="pbr-m1"
;;
*"PSG1208")
name="psg1208"
;;
*"PSG1218")
name="psg1218"
;;
*"PSR-680W"*)
name="psr-680w"
;;
*"PWH2004")
name="pwh2004"
;;
*"PX-4885")
name="px-4885"
;;
*"Q7")
name="zte-q7"
;;
*"RE6500")
name="re6500"
;;
*"RN502J")
name="xdxrn502j"
;;
*"RP-N53")
name="rp-n53"
;;
*"RT5350F-OLinuXino")
name="rt5350f-olinuxino"
;;
*"RT5350F-OLinuXino-EVB")
name="rt5350f-olinuxino-evb"
;;
*"RT-G32 B1")
name="rt-g32-b1"
;;
*"RT-N10+")
name="rt-n10-plus"
;;
*"RT-N13U")
name="rt-n13u"
;;
*"RT-N14U")
name="rt-n14u"
;;
*"RT-N15")
name="rt-n15"
;;
*"RT-N56U")
name="rt-n56u"
;;
*"RUT5XX")
name="rut5xx"
;;
*"SamKnows Whitebox 8")
name="sk-wb8"
;;
*"SAP-G3200U3")
name="sap-g3200u3"
;;
*"SL-R7205"*)
name="sl-r7205"
;;
*"TEW-691GR")
name="tew-691gr"
;;
*"TEW-692GR")
name="tew-692gr"
;;
*"TEW-714TRU")
name="tew-714tru"
;;
*"Timecloud")
name="timecloud"
;;
ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX) This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
*"UBNT-ERX")
name="ubnt-erx"
;;
*"UR-326N4G")
name="ur-326n4g"
;;
*"UR-336UN")
name="ur-336un"
;;
*"V11ST-FE")
name="v11st-fe"
;;
*"V22RW-2X2")
name="v22rw-2x2"
;;
*"VoCore")
name="vocore"
;;
*"VR500")
name="vr500"
;;
*"W150M")
name="w150m"
;;
*"W306R V2.0")
name="w306r-v20"
;;
*"W502U")
name="w502u"
;;
*"WCR-150GN")
name="wcr-150gn"
;;
*"WF-2881")
name="wf-2881"
;;
*"WHR-1166D")
name="whr-1166d"
;;
*"WHR-300HP2")
name="whr-300hp2"
;;
*"WHR-600D")
name="whr-600d"
;;
*"WHR-G300N")
name="whr-g300n"
;;
*"Widora-NEO")
name="widora-neo"
;;
*"WiTi")
name="witi"
;;
*"WIZARD 8800")
name="wizard8800"
;;
*"WizFi630A")
name="wizfi630a"
ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX) This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
;;
*"WL-330N")
name="wl-330n"
;;
*"WL-330N3G")
name="wl-330n3g"
;;
*"WL-341 v3")
name="wl-341v3"
;;
*"WL-351 v1 002")
name="wl-351"
;;
*"WLI-TX4-AG300N")
name="wli-tx4-ag300n"
;;
*"WMR-300")
name="wmr-300"
;;
*"WNCE2001")
name="wnce2001"
;;
*"WNDR3700v5")
name="wndr3700v5"
;;
*"WR512-3GN-like"*)
name="wr512-3gn"
;;
*"WR6202")
name="wr6202"
;;
*"WRH-300CR")
name="wrh-300cr"
;;
*"WRTNODE")
name="wrtnode"
;;
*"WRTnode2R")
name="wrtnode2r"
;;
*"WRTnode2P")
name="wrtnode2p"
;;
*"WSR-1166DHP")
name="wsr-1166"
;;
*"WSR-600DHP")
name="wsr-600"
;;
*"WT1520")
name="wt1520"
;;
*"WT3020")
name="wt3020"
;;
*"WZR-AGL300NH")
name="wzr-agl300nh"
;;
*"X5")
name="x5"
;;
*"X8")
name="x8"
;;
*"Y1")
name="y1"
;;
*"Y1S")
name="y1s"
;;
*"ZBT-APE522II")
name="zbt-ape522ii"
;;
*"ZBT-CPE102")
name="zbt-cpe102"
;;
*"ZBT-WA05")
name="zbt-wa05"
;;
*"ZBT-WE826")
name="zbt-we826"
;;
*"ZBT-WG2626")
name="zbt-wg2626"
;;
*"ZBT-WG3526")
name="zbt-wg3526"
;;
*"ZBT-WR8305RT")
name="zbt-wr8305rt"
;;
*"YK1")
name="youku-yk1"
;;
*)
name="generic"
;;
esac
[ -z "$RAMIPS_BOARD_NAME" ] && RAMIPS_BOARD_NAME="$name"
[ -z "$RAMIPS_MODEL" ] && RAMIPS_MODEL="$machine"
[ -e "/tmp/sysinfo/" ] || mkdir -p "/tmp/sysinfo/"
echo "$RAMIPS_BOARD_NAME" > /tmp/sysinfo/board_name
echo "$RAMIPS_MODEL" > /tmp/sysinfo/model
}
ramips_board_name() {
local name
[ -f /tmp/sysinfo/board_name ] && name=$(cat /tmp/sysinfo/board_name)
[ -z "$name" ] && name="unknown"
echo "$name"
}