Commit graph

955 commits

Author SHA1 Message Date
Piotr Dymacz
2eeb8ac271 ar71xx: image: fix typo in tp-link.mk
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Henryk Heisig
ca6002c0ef ar71xx: increase kernel partition size for some TP-Link boards
This patch increases kernel partition size and re-enables image
generation for below TP-Link boards:

- archer-c58-v1
- archer-c60-v1
- tl-wr902ac-v1
- tl-wr942n-v1

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[commit message and title reworded]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Henryk Heisig
34958c8269 ar71xx: Archer C58/C59/C60 fix qca9886 wireless interface
This commit fix 5GHz wireless interface used in Archer C58/C59/C60v1
and set correctly MAC address on this interface.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-10-26 14:44:08 +02:00
Julien Dusser
8d9ff6b6f7 ar71xx: lzma loader use LTO
Change the Makefile to use LTO for better code optimisations. Gains are
very low, only 270 bytes saved, but it's only Makefile changes.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2017-10-24 13:24:04 +02:00
Julien Dusser
8c5702f2a0 ar71xx: fix lzma loader performance issues
Some bootloaders set a cache cohenrency to a very slow mode. Use code from
Linux kernel to set it to "Cacheable, noncoherent, write-back, write
allocate".

Perfomance impact is significant on TP-Link EAP245 board, kernel
decompression time fall from 33 seconds to less than 1.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2017-10-24 13:24:04 +02:00
Hauke Mehrtens
f7a6fd3153 ar71xx: deactivate some boards with too small kernel partitions
This affects the following boards:
 * dr344
 * archer-c58-v1
 * archer-c60-v1
 * tl-wr902ac-v1
 * tl-wr942n-v1
 * ubnt-uap-pro
 * ubnt-unifi-outdoor-plus

The build fails for any of these boards because the resulting kernel
image will not fit into the kernel partition.

When CONFIG_KERNEL_KALLSYMS  is not set it could be that the kernel will
fit onto the board again, this is the case for release images.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-22 23:15:11 +02:00
Felix Fietkau
9887afb1af ar71xx: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 16:14:19 +02:00
Felix Fietkau
2c9aff289e ar71xx: add support for Nokia WI2A-AC200i
Specifications:
 - SoC: Qualcomm QCA9558 (720 MHz)
 - RAM: 256MB
 - Storage: 1MB NOR, 128 MB NAND flash
 - Ethernet: 1x1000M

Installation:
 1. Connect to serial console on the board
 2. Boot initramfs image over u-boot
 3. Copy image to the device and run sysupgrade

Installation without serial console is not supported at this time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 12:27:42 +02:00
Robert Marko
443abb8ccd ar71xx: add support for Mikrotik RB750P-PBr2
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 4 PoE out)
- Outdoor use ready

This ethernet router is based on the same platform as the hEX PoE lite.

Installation

1. login to the Mikrotik WebUI to backup your licence keys
2. setup a DHCP/BOOTP Server with:
     * DHCP-Option 66 (TFTP server name) pointing to a local TFTP
       Server within the same subnet of the DHCP range
     * DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
       of the to be booted image
3. connect the port labled internet to your local network
4. keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
Server. Login as root/without password to the started LEDE via ssh
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
  * rbcfg set boot_protocol bootp
  * rbcfg set boot_device ethnand
  * rbcfg apply

Open Netinstall and reboot routerboard. Now netinstall sees routerboard
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-10-14 10:48:29 +02:00
Mathias Kresin
1c4a116a30 ar71xx: add rssileds to WA850RE v1 image
A default rssileds config exists for the TP-Link WA850RE v1 but the
rssiled package is not included by default.

The compressed 17.01.3 image size increases by 3302 bytes which should
be tolerable even for a 4MB flash board.

Fixes: FS#1043

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-07 20:15:03 +02:00
Catrinel Catrinescu
cd4b60c329 ar71xx: ew-dorin target moved from legacy to generic
Embedded Wireless Dorin platform moved from legacy to generic

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2017-10-07 09:20:04 +02:00
Enrique Giraldo
b8b410fba3 ar71xx: add metadata to wpj344 and wpj558 images
This adds metadata to wpj344 and wpj558 images to prevent loading
firmware of wpj344 into wpj558 and vice versa. This until now was
possible and break the units and had to be recovered from the uboot.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
2017-09-10 22:15:04 +02:00
Enrique Giraldo
fefdb1e0b9 ar71xx: add support for COMFAST CF-E355AC
COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9882.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 64MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
[whitespace fixes, ac radio caldata offset fix]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:15:03 +02:00
Piotr Dymacz
90d8c0f0a2 ar71xx: add support for GL.iNet GL-USB150
GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:14:43 +02:00
Piotr Dymacz
2ad2946777 ar71xx: image: use tplink-v1-header in place of mktplinkfw-kernel
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
f08f754993 build: move mktplinkfw-combined command to image-commands.mk
We will need "mktplinkfw-combined" command also in the "ramips" target
for new MediaTek based TP-Link devices, with "safeloader" image type.

Also, rename the command to "tplink-v1-header", use "VERSION_DIST"
variable instead of "OpenWrt" and allow passing additional parameters.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
b3cb0e7588 firmware-utils: mktplinkfw: rework combined image option
We use combined option in "mktplinkfw" tool for generating initramfs
kernel images and header for kernel inside "safeloader" image type (in
fact, only for TL-WR1043ND v4 at this moment).

There is also "mktplinkfw-kernel" tool, a stripped-down version, used
only for generating "simple" header, for safeloader image types.

This changes how "mktplinkfw" handles combined images (which then will
allow us to drop the stripped-down version of the tool):

- drop "ignore size" command line option (it was used only for combined
  images anyway)
- don't require "flash layout id" for combined images (we don't need and
  shouldn't limit size of the initramfs kernel and for kernels inside
  safeloader images, the "tplink-safeloader" tool does the size check)
- require kernel address and entry point in command line parameters for
  combined images (consequence of previous point)
- don't include md5 sum and firmware length values in header (they are
  needed only for update from vendor GUI and are ingored in case of
  initramfs and "tplink-safeloader" images)
- drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed

Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to
match introduced changes in "mktplinkfw" tool.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
0c6165d21a ar71xx: add support for ALFA Network AP121F
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB

Flash instruction (under U-Boot web recovery mode):

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
   wait for first blink of all LEDs (indicates network setup), then keep
   button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:13:55 +02:00
Alexander Couzens
8c96eb2fdb
ar71xx/image: change unifi UBNT_CHIP to ar7240
Verified by OEM firmware images which contains the same
chip.

Tested-by: Andreas Bräu <ab@andi95.de>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-07-13 23:56:24 +02:00
Matthias Schiffer
16222a1010
ar71xx: set US region code for TP-Link TL-WR710N v1 image
Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so
far, so we can just set US unconditionally.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-12 21:30:08 +02:00
Piotr Dymacz
9d07d2dc56 ar71xx: image: simplify Meraki MR16 device definition
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:46:53 +02:00
Henryk Heisig
096a604df0 ar71xx: add metadata to some TP-Link images
This commit adds metadata to TP-Link sysupgrade images
created by tplink-safeloader with uImage kernel header.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-07-09 22:45:59 +02:00
Piotr Dymacz
cf23547e57 ar71xx: fix TPLINK_BOARD_ID for Archer C58 and TL-WA855RE
Rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID for two ommited devices.

Fixes: 7d6c63d ("build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 15:09:52 +02:00
Piotr Dymacz
6165e4aab0 ar71xx: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

Root access over serial line in vendor firmware: root/sohoadmin.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
a73471dea7 ar71xx: image: specify TPLINK_HWID for TP-Link RE450
TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin.
As we don't want to break sysupgrade (all existing LEDE release images
for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0.

Fixes FS#852

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:46:08 +02:00
Piotr Dymacz
7d6c63d875 build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Henryk Heisig
b05c7193fd ar71xx: add support for TP-Link Archer C58 v1
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-06-29 10:37:36 +02:00
Federico Cappon
9fec39a033 ar71xx: add support for TP-Link TL-WA855RE v1
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Federico Cappon <dududede371@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
656ed7544f ar71xx: fix EnGenius ENS202EXT mtd definition
Use statically defined sizes for kernel and rootfs mtd partitions.
Vendor upgrade script writes both firmware parts independently which
ends up in a gap between kernel and rootfs images. This results in
incorrectly calculated rootfs_data start offset.

Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL
definition.

Fixes FS#835

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Camille Bilodeau
bb46b635df ar71xx: move Arduino Yun to generic building code
Migrate Arduino Yun from legacy to generic building code.

Note: the mtd partitioning is changed to adopt the LEDE default
partitioning. It allows to have a kernel bigger than 1280k. It is
necessary as kernel > 4.4 with default LEDE configuration grows
bigger.

To use the new partitioning, you need to update your U-Boot env in
advance:

setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
saveenv

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Camille Bilodeau
2fa58a8d7c ar71xx: remove Arduino Yun 8 MiB prototype
The Arduino Yun has 16 MiB flash. Early prototype boards with 8 MiB were
not available for sell:

https://blog.arduino.cc/2013/08/21/updating-about-arduino-yun-and-arduino-robot/

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Alexander Couzens
d98cafc7b6
ar71xx/images/senao: fix reproducible issue using tar
Use deterministic sorting
Use numeric owner/group
Set uid/gid to 0

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-25 12:14:26 +02:00
Alexander Couzens
d6331d5583 ar71xx/image: make tar calls reproducible
Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-25 12:11:41 +02:00
Mathias Kresin
e7cd6f5d66 ar71xx: add AVM FRITZ!WLAN Repeater 300E support
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Piotr Dymacz
3ff31586eb ar71xx: image: simplify TP-Link devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
8b556fb056 ar71xx: image: fix TP-Link TL-WR710N v2/v2.1 BOARDNAME
All TP-Link TL-WR710N versions share the same machine code.

This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
7efe0cd83d ar71xx: image: tp-link.mk: keep devices in alphabetical order
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Ludwig Thomeczek
b4711dbad3 ar71xx: add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[minor code style fixes, boards alphabetical order fixes,
reworked commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Serg Studzinskii
b7cc661615 ar71xx: add support for TP-Link TL-WR942N v1
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
641af0c39d ar71xx: move WRTnode2Q to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
636ae9e9a0 ar71xx: image: simplify Ubiquiti devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
01aa23acf7 ar71xx: image: mikrotik: shorten DEVICE_TITLE
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
7bc5571d14 ar71xx: image: use simply expanded variables
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
80136e57a4 ar71xx: image: update GL.iNet boards DEVICE_TITLE
Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:31:25 +02:00
Piotr Dymacz
93198b8335 ar71xx: image: fix 8devices boards DEVICE_TITLE
Be consistent with DEVICE_TITLE syntax and use vendor + board names.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:30:05 +02:00
Piotr Dymacz
bd92a6cf57 ar71xx: image: drop unused mtdlayouts from legacy.mk
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
708cc2bd3c ar71xx: image: cosmetic: drop redundant empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
e83cac1a8f ar71xx: image: add ROOTFS_SIZE to DEVICE_VARS
Also use ROOTFS_SIZE variable in place of static values.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
c00fb14329 ar71xx: image: keep custom Build/* functions in separate files
Most of the custom Build/* functions in ar71xx target are rarely used by
image building code for devices from more than one subtarget. As they
don't need to be always included, move them to corresponding *.mk files.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
3a3cd0ac43 ar71xx: image: keep DEVICE_VARS and Build/* at the beginning
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:21:45 +02:00
Piotr Dymacz
af27dd1a51 ar71xx: image: simplify Compex devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Piotr Dymacz
43c0ef1010 ar71xx: image: drop redundant kmod-usb-ohci from DEVICE_PACKAGES
kmod-usb-ohci is needed only on devices with AR71xx and AR7240 SoCs.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Piotr Dymacz
05e276c071 ar71xx: image: drop redundant uboot-envtools from DEVICE_PACKAGES
uboot-envtools is already included in DEFAULT_PACKAGES for ar71xx.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Piotr Dymacz
6173f6d8f1 ar71xx: move Wallys DR344 to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:34:09 +02:00
Marty Plummer
558d86923e ar71xx: add support for EnGenius ENS202EXT
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.

The device is based on Qualcomm/Atheros AR9341 v1.

Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button

Flash instructions:

You have three options:

- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.

- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.

- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:

*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
      stat -- Status
       sys -- System
    wless2 -- 2.4G-Wireless
      mgmt -- Management
      tree -- Tree
      help -- Help
    reboot -- Reboot
ens202ext>mgmt
  Management
---========= Commands Help =========---
     admin -- Administration
     mvlan -- Management VLAN settings
      snmp -- SNMP settings
    backup -- Backup/Restore settings
    autorb -- Auto reboot settings
   fwgrade -- Firmware upgrade
      time -- Time settings
   wifisch -- Wifi schedule
       log -- Log
      diag -- Diagnostics
      disc -- Device Discovery
    logout -- Logout
      help -- Help
      exit -- Exit
ens202ext/mgmt>fwgrade
  Management --> Firmware upgrade
---========= Commands Help =========---
      fwup -- Firmware upgrade
      help -- Help
      exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin

Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
2017-05-30 14:15:25 +02:00
Andrey Polischuk
0f21873f7f ar71xx: fix LED defines for TP-Link TL-WR740N v6
Signed-off-by: Andrey Polischuk <androld.b@gmail.com>
[changed commit subject, dropped redundant kernel config symbol]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:15:25 +02:00
Filip Moc
43e4e1f4a5 Move enablemodem from ramips to new package adb-enablemodem and make it used also by TL-MR6400
Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:40 +02:00
Filip Moc
a639cbfd00 ar71xx: Add support for TP-Link MR6400
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.

Hardware Specification (v1.0 EU):
 - SoC: QCA9531
 - Flash: Winbond W25Q64FV (8MiB)
 - RAM: EtronTech EM6AB160TSE-5G (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 2NIC (3x100M + 1x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 12V 1A

Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:21 +02:00
Matthias Fritzsche
a4e63e2679 ar71xx: change image version for ubiquiti devices
changes the image version from hardcoded OpenWrt to
$VERSION_DIST. AirOS shows a notification with the image version
during a firmware upgrade.

fixes #582

Signed-off-by: Matthias Fritzsche <txt.file@txtfile.eu>
2017-05-25 09:22:37 +02:00
John Crispin
bad2f9c4dc Revert "ar71xx: Add support for Teltonika RUT900"
This reverts commit 224e5f5efa.

pepe2k pointed out that this was not ready to merge

Signed-off-by: John Crispin <john@phrozen.org>
2017-05-18 15:31:47 +02:00
Steffen Weinreich
224e5f5efa ar71xx: Add support for Teltonika RUT900
Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet
ports, I/O, RS232, RS485, GPS.

The device ist based on a Atheros AR9344 rev 3,

Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM
- 16 MB of FLASH
- Serial Console header on a Card Board edge connector
- 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN)
- 2.4 GHz Wifi
- 2x external, detachable Wifi antennas
- LTE Modem Huawei ME909u-521 (Also other Modem seen)
- 2x LTE antennas
- 1x GPS antenna
- 7x LED, 1x button
- 1x USB Connector
- 1x Serial RS232
- 1x Serial RS485
- 1x MicroSD Card

The GPL sources of the device are available at www.teltonika.lt/gpl/
and are based on OpenWRT Barrier Breaker (14.07)

Running from tftp:

The Router starts into the uboot Webupdater if the Button ist pressed
more than 3 seconds, if no Network cable is attached it starts the
uboot serial console, from there the router loads the firmware image
via tftpboot from 192.168.1.2:firmware.bin (the router has the
192.168.1.1). With bootm the loaded image will be booted.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
2017-05-18 14:47:53 +02:00
Chris Blake
10d11859df ar71xx: add support for Aerohive AP-121
This adds support for Aerohive AP-121 access point.

Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204

Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:

dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[minor text changes in commit subject and description, fixed
alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh,
fixed code style issues in mach-hiveap-121.c, ubinized factory image]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:58:59 +02:00
Mantas Pucka
68b5d34f69 ar71xx: add support for 8devices Rambutan development board
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan

This commit adds basic support for Rambutan development kit

Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header

Flash instructions:
Stock firmware is OpenWrt, so use:
 sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
 tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
 nand erase.part ubi
 nand write 80060000 ubi ${filesize}

Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Ludwig Thomeczek
43a7a1a05e ar71xx: add support for UniFi-AC-Mesh
This adds the build option for the new UniFi AC Mesh.
It is a direct hardware copy from the AC Lite.

- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 1 1000M - POE
- Wireless:
        2.4G: QCA9563
          5G: UniFi Chip, QCA988X compatible

Thanks to Frank Dietz for testing.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[wrapped too long lines in mach-ubnt-unifiac.c]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Piotr Dymacz
1c56a7929a ar71xx: move Zbtlink ZBT-WE1526 to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-15 22:43:33 +02:00
Felix Fietkau
c536c50171 ar71xx: enable nand-utils in the mikrotik subtarget to ensure it makes it to initramfs
Without it, sysupgrade from initramfs to nand fails

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-05-12 13:29:55 +02:00
Piotr Dymacz
190db43615 ar71xx: tp-link.mk: always include device version in image and DEVICE_TITLE
There are currently several supported TP-Link devices without specified
version number in image name and/or DEVICE_TITLE (e.g. WBS210, WBS510,
TL-WR810N, TL-WA7510N, TL-WPA8630), but vendor website shows that there
are already more than one version of them on the market.

For devices like Archer C5, which second version is based on a total
different platform, missing version number in DEVICE_TITLE (used in
menuconfig) might be misleading for users.

To make it less confusing for users and easier to maintain in future,
include version number in image name and DEVICE_TITLE for all TP-Link
devices, even if there is only one version of device at the moment.

Also, keep DEVICE_TITLE in same format for all TP-Link devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
2017-04-03 12:29:07 +02:00
Vittorio Gambaletta
539e2a78f0 ar71xx: add TP-LINK TL-WR841N/ND v12 image
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).

If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.

The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2017-04-03 12:29:07 +02:00
Christian Mehlis
dc4eae7a8c ar71xx: Compex WPJ563 support
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G

Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer

Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000

Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize

Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-30 09:57:22 +02:00
John Crispin
95c333a3b5 ar71xx: drop default CONSOLE values
Compex boards dont need to set these as they are default.

Signed-off-by: John Crispin <john@phrozen.org>
2017-03-29 09:22:46 +02:00
Christian Mehlis
be11ce8f26 ar71xx: move Compex WPJ342 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-29 09:04:08 +02:00
Christian Mehlis
0af487033e ar71xx: move Compex WPJ344 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-29 09:04:08 +02:00
Christian Mehlis
f5ece7326a ar71xx: move Compex WPJ531 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-29 09:04:08 +02:00
Christian Mehlis
f940fe8964 ar71xx: move Compex WPJ558 to generic build target
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-29 09:04:08 +02:00
Mathias Kresin
86a0cbb333 treewide: select ath10k firmware explicit
Do not rely on the default firmware selected by ath10k.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
Piotr Dymacz
597c9f0be5 ar71xx: image: fix indentation
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 22:02:47 +01:00
Piotr Dymacz
4436979c83 ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.

CPE505 is an outdoor CPE with PoE support and detachable antennas.

Both devices are based on Qualcomm/Atheros QCA9531 v2.

Common specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB

R602N specification:

- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button

CPE505N specification:

- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button

Flash instructions:

It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").

Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:

fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"

Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.

If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:

1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset

These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".

Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 17:59:47 +01:00
Vaclav Svoboda
0d9adb4832 ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.

- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
   (v2: Macronix MX 25L323F)
   (v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-23 09:41:15 +01:00
Ryan Mounce
978998628f ar71xx: add support for MikroTik hAP ac
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).

All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Ryan Mounce
540edf7045 ar71xx: add support for MikroTik hAP ac lite
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).

The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Thibaut VARENE
e3dc036cbf ar71xx: add support for RB LHG 5nD
This patch adds support for the MikroTik RouterBOARD LHG 5
https://routerboard.com/RBLHG-5nD

Specifications:
- SoC: Atheros AR9344 (600MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin AR9344 5GHz, 2x2:2
- Ethernet: 1x100M

Initial flash via initramfs, like all other RB devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Shuanglin Liu
53ef20f65a ar71xx: add support for Rockeetech AP531B0
Specification:
- SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB))
- RAM: 64 MiB DDR2
- Storage: 16 MiB of flash (optional 16 MiB second flash)
- Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0) 1x100M (port 4)
- PCI-E: x1
- SIMcard slot: x1
- USB 2.0 port: x1 (optional)
- Ext GPIO pin: x8
- UART for serial console: x1
- External watchdog: x1 (optional)
- Power supply: 9-48V (DC jack/passive PoE)

Installation through tftp:
- Copy <Firmware Image Name> into tftp directory
- Connect board via ttl port and Ethernet port
- Boot the AP531B0
- When "Autobooting in 1 seconds" appears press Enter
- Set serverip and ipaddr appropriate
  (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1)
- Enter "tftp 0x8050000 <Firmware Image Name>"
- Enter "erase 0x9f050000 +$filesize"
- Enter "cp.b 0x80500000 0x9f050000 $filesize"
- Enter "reset"

Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
2017-03-12 17:38:31 +01:00
Stijn Segers
0ad82375cd ar71xx: add ath10k driver and firmware for Netgear R6100 to firmware image
A Netgear R6100 owner reported the LEDE images lack the ath10k driver and firmware [1]. This patch adds both to the R6100 image.

[1] https://forum.lede-project.org/t/netgear-r6100-5ghz-wifi-not-working-after-initial-install/2222

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2017-03-11 08:30:56 +01:00
Felix Fietkau
eb4f70a3cd ar71xx: use common firmware partition for WNDAP360
Patch from https://github.com/openwrt/openwrt/pull/398

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-23 16:27:47 +01:00
Thibaut VARENE
f6a52bf337 ar71xx: Enable mtdsplit support for RB SPI NOR devices
This patch enables mtdsplit for the MikroTik subtarget.
It converts mach-rbspi.c to use a single "firmware" partition.
Finally, it converts the SPI NOR profile to metadata images:
the original combined-image format is gone, the images are now
"standard" sysupgrade images with metadata appended.

Note: kernel2minor apparently pads the kernel container to erase-block
boundary, but this is undocumented behaviour, so we do not rely on it
and call pad-to anyway.

Note: in platform.sh, the boards are tested last in platform_check_image()
as this should eventually become the "*)" default case when more devices
switch to metadata images.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-22 22:52:20 +01:00
Thomas Roberts
f9278337cf ar71xx: add support for TL-WR802N Version 2
This patch adds support for the TP-Link TL-WR802N Version 2.

Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
2017-02-20 09:10:17 +01:00
Karol Dudek
58fc50f1b0 ar71xx: add support for 8devices Lima board
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.

Specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO

Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery

Tested on:

- Lima development kit

Signed-off-by: Karol Dudek <karoiz@sli.pl>
2017-02-17 10:19:09 +01:00
Thibaut VARENE
b18bae37a4 ar71xx: provide support for RB-941-2nD via mach-rbspi.c
This patch implements support for the hAP lite in mach-rbspi.c

hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Thibaut VARENE
c59fa94eee ar71xx: add support for RB mAP L-2nD
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD

Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M

This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Felix Fietkau
f533b94436 ar71xx: fix DEFAULT_PACKAGES for mikrotik devices
Include packages from the default profile for NAND devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-14 13:15:44 +01:00
Alexandru Gagniuc
6cce9557a0 ar71xx: Add support for D-Link EBR-2310 Rev. C
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2017-02-14 12:27:14 +01:00
Piotr Dymacz
56561b9f51 ar71xx: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-14 12:25:33 +01:00
Sven Eckelmann
3d16c16eb6 ar71xx: Add missing device package om-watchdog for MR1750
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
391d498fe5 ar71xx: add OpenMesh A40 to OpenMesh A60 profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
5e50adeed3 ar71xx: create profile and build image for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
019276a9c6 ar71xx: Remove the v2/v3 from the OpenMesh profile names
The list of v2/v3 devices is getting longer and makes reading the names of
the profiles unnecessary hard.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Piotr Dymacz
f5416b0622 ar71xx: image: drop redundant CONSOLE assignment
Default CONSOLE value for ar71xx target is "ttyS0,115200", so there
is no need to specify the same value in device profiles.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-09 09:45:27 +01:00
Piotr Dymacz
a4d12aed30 ar71xx: image: fix DEVICE_TITLE for several devices
Be consistent with form and format of the vendor names.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Felix Fietkau
1533f1db92 ar71xx: add missing DEVICE_TITLE for mikrotik devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-29 17:32:48 +01:00
FUKAUMI Naoki
e5a0eb2af5 ar71xx: prepare jffs2 partition properly in factory.bin for BHR-4GRV2
"pad-rootfs" is required just after "append-rootfs".

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-28 20:29:00 +01:00
Henryk Heisig
e39dc8d823 ar71xx: add support to TP-Link Archer C59v1 and C60v1
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB

TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")

Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:21 +01:00
Alex Samorukov
17401b3d5c ar71xx: improve Mikrotik hAP Lite device support
- remove CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
- enable jffs2 support
- fix sysupgrade

Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
2017-01-25 08:00:11 +01:00
Felix Fietkau
83783f296a uboot-ar71xx: switch to using u-boot.mk
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 16:21:24 +01:00
John Crispin
236fcedc51 Revert "ar71xx: wrt400n: lift size limit on kernel and rootfs part"
This reverts commit 78c2ec0f47.

The builders were failing with a segfault when generating the image

Signed-off-by: John Crispin <john@phrozen.org>
2017-01-20 06:43:13 +01:00
YuheiOKAWA
261415a660 ar71xx: add support for PQI Air Pen
SoC: AR9331
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

Changes in v2:
alphabetical ordering, tabs fron spaces.
2017-01-20 00:52:48 +01:00
Yousong Zhou
78c2ec0f47 ar71xx: wrt400n: lift size limit on kernel and rootfs part
While at it, convert to new build method

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-20 00:44:46 +01:00
Conor O'Gorman
274546046d ar71xx: add Abicom SC1750 support
Support Abicom International Scorpion SC1750 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB Nor Flash
1x SFP, 1x PCIe
2x 10/100/1000 Ethernet
135x100 mm
802.11ng/g/b
802.11ac/an/a

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:40 +01:00
Conor O'Gorman
d38ffd8cd9 ar71xx: add Abicom SC450 support
Support Abicom International Scorpion SC450 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:33 +01:00
Conor O'Gorman
eb97f41fc2 ar71xx: add Abicom SC300M support
Support Abicom International Scorpion SC300M Module

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:27 +01:00
Thibaut VARENE
3f7841a70a ar71xx: add support for RB-941-2nD
Add full support for Mikrotik RB-941-2nD (hAP lite)

Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
Felix Fietkau
9db9072d67 ar71xx: convert mikrotik routerboard support to UBI
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.

There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
Felix Fietkau
b1dbe6028e ar71xx: fix legacy image build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:09:21 +01:00
Stijn Tintel
0d3dc16931 ar71xx: drop references to madwifi
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:02:00 +01:00
Matthias Schiffer
1fef80f29c
ar71xx: add support for TP-Link WBS210/510
The devices are mostly identical to the CPE210/510, but use external
antennas.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-01-05 16:01:17 +01:00
Radek Dostál
3561d89ad6 ar71xx: RE450: enable building of TP-Link RE450
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:06 +01:00
Tal Keren
0d9d980ecd firmware-utils: kernel image generator for TP-Link RE450
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:05 +01:00
Matthias Schiffer
324bdf3ecc
ar71xx: remove redundant -j from TL-WR1043ND v4 kernel build command
mktplinkfw ignores -j in combined mode, the EOF marker is added by
tplink-safeloader.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-21 23:29:00 +01:00
Ludwig Thomeczek
1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
Matthias Schiffer
0495181529
ar71xx: rename mktplinkfw-initramfs to more generic mktplinkfw-combined
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-20 14:38:48 +01:00
David Lutz
aada15af93
ar71xx: add support for TP-LINK TL-WR940N v4
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
2016-12-16 11:12:46 +01:00
Gad Krumholz
21cb84435a ar71xx: Added missing support for Linksys E2100L
It's based on the WRT160NL according to
https://wiki.openwrt.org/toh/linksys/e2100l

Based on research done here: https://forum.openwrt.org/viewtopic.php?id=24244
and here: https://forum.openwrt.org/viewtopic.php?pid=120791#p120791 this patch
was conceived.

Signed-off-by: Gad Krumholz <gad.krumholz@gmail.com>
[Jo-Philipp Wich: fix ordering, move addpattern change into separate commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-14 18:42:48 +01:00
Huan Truong
fd62fa752b ar71xx: Add support for Netgear WNR2000v1
This patch adds supports for the WNR2000v1 board with 4MB flash, and
produces device-specific factory, rootfs, and sysupgrade files for the
WNR2000v1. This board is errorneously claimed as supported on the OpenWRT
wiki as AP81, but AP81 image would not work because of APT81 image
requiring having 8MB of flash, while WNR2000v1 has only 4MB.

The image requires the u-boot bootloader to be modified to fuhry's
bootloader first.

Short specification:

- CPU: Atheros AR9132
- 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps
- 4 MB of Flash
- 32 MB of RAM
- UART header (J1) on board
- 1x button

Factory/Initial flash instructions:

- Set up a TFTP server on your local machine.
- Download the uImage for ar71xx-generic and the rootfs image for
  ar71xx-generic-wnr2000 and save in the tftp server root.
- Gain serial access to the router via the UART port (telnetenable over
  the network only won't work!).
- Upgrade the u-boot bootloader to fuhry's version by running the
  script: http://fuhry.com/b/wnr2000/install-repart.sh
- When the router restarts, interrupt u-boot and gain access to u-boot command line.
- Repartititon the board and flash initial uImage and rootfs as follow.

Commands to type in u-boot:

	# tells u-boot that we have a tftp server on 192.168.1.10
	setenv serverip 192.168.1.10

	# tells u-boot that the router should take the address 192.168.1.1
	setenv ipaddr 192.168.1.1

	# erase the region from 0x050000-0x3f0000
	erase 0xbf050000 +0x3A0000

	# loads sqfs.bin on TFTP server, and put it to memory address 0x81000000
	tftpboot 0x81000000 sqfs.bin
	# it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ
	# copy bit by bit 0xZZZZZZ bytes from offset 0x050000
	cp.b 0x81000000 0xbf050000 0xZZZZZZ

	# same to the uImage.bin, write it right next to sqfs.bin
	# again, 0xYYYYYY is the length that tftpboot reports
	tftpboot 0x81000000 uImage.bin
	cp.b 0x81000000 0xbf2a0000 0xYYYYYY

	# We need to tell the kernel what board it is booting into, and where to find the partitions
	setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd"

	# Tell u-boot where to find the uImage
	setenv bootcmd "bootm 0xbf2a0000"

	# Tell u-boot to save parameters to the u-boot-env partitions
	saveenv

	# Reset the board
	reset

Tested on:

- WNR2000v1 board.
- Initial flash works.

Known bugs:

- I don't know why factory image doesn't work on initial flash on stock
  firmware in u-boot recovery mode while it should.
- Sysupgrade does not yet work, if you do -f it will mess up your
  installation (requiring a reinstall of sqfs and uImage).

Signed-off-by: Huan Truong <htruong@tnhh.net>
2016-12-14 10:37:01 +01:00
Jing Lin
c9a9f9b8ce ar71xx: Add ath10k-firmware-qca988x for DomyWifi DW33D
The default package selection was missing the correct FW for ath10k to
work.

Signed-off-by: Jing Lin <mumuqz@163.com>
2016-12-14 10:37:01 +01:00
Felix Fietkau
4c8a9b8e39 ar71xx: remove AP81 reference design board support
This board is very old and unlikely to still be relevant today.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
441ee62931 ar71xx: remove AP83 reference design board support
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Piotr Dymacz
c198ca682c ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00
Felix Fietkau
1cd7ff3e96 ar71xx: remove squashfs-64k rootfs image from bin directory, the generic one is enough
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 10:20:27 +01:00
Felix Fietkau
eff858e8df ar71xx: remove split kernel/rootfs images where the sysupgrade image can be written to flash directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 10:20:27 +01:00
Felix Fietkau
cc550d0005 ar71xx: remove 2MB flash variant of WP543
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:55:05 +01:00
Felix Fietkau
12e2beaaed ar71xx: remove legacy devices that cannot be supported due to kernel partition size limits
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:51:57 +01:00
Felix Fietkau
35dda35114 ar71xx: remove legacy gzip images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:44:39 +01:00
Felix Fietkau
88f6f0120d ar71xx: remove obsolete jffs2 image building code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:44:39 +01:00
Piotr Dymacz
6998b8a054 ar71xx: move DomyWifi DW33D to nand subtarget
This device uses NAND FLASH, so it should be kept in nand subtarget.

Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-24 22:37:40 +01:00
Piotr Dymacz
e33dcd1cfe ar71xx: add support for YunCore CPE830
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.

Use the same flash approach as for YunCore AP90Q.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
eb9ba2b91e ar71xx: add support for YunCore CPE870
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:

- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset

Vendor firmware access (login/password): Admin/5up

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
01dda0659e ar71xx: add support for YunCore AP90Q
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Flash instruction under vendor fimrware, using telnet/SSH:

1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
31952dbd1c ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530N
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.

All 3 devices are based on Qualcomm/Atheros QCA9531 v2.

COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Henryk Heisig
0d760bfba8 ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partition
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-16 11:01:18 +01:00
FUKAUMI Naoki
0165203304 ar71xx: add support for Buffalo BHR-4GRV2
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2016-11-16 10:54:33 +01:00
Matthias Schiffer
60983a486c
ar71xx: fix DEVICE_TITLE for Ubiquiti UAP Outdoor+
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-15 18:54:06 +01:00
Matthias Schiffer
9cac5e8be0
ar71xx: generate region-coded factory images for TP-Link TL-WR841ND v11
The latest stock firmwares for US and EU regions have started checking the
region code.

Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-11 03:29:59 +01:00
Felix Fietkau
462a7c0e96 ar71xx: fix kernel relocate stub parallel build issue
Use per-kernel directory

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-08 11:51:27 +01:00
Henryk Heisig
4ad68fa0a2 ar71xx: tl-wpa8630: Fix kernel lenght
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
6b0d279ca5 ar71xx: build relocate stub for generic and legacy images
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Chuanhong Guo
c5a7e2c2fb ar71xx: Ignore firmware building errors of UBNT and CyberTAN devices
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-10-26 14:07:20 +02:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00