ar71xx: add support for EnGenius ENS202EXT

EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.

The device is based on Qualcomm/Atheros AR9341 v1.

Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button

Flash instructions:

You have three options:

- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.

- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.

- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:

*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
      stat -- Status
       sys -- System
    wless2 -- 2.4G-Wireless
      mgmt -- Management
      tree -- Tree
      help -- Help
    reboot -- Reboot
ens202ext>mgmt
  Management
---========= Commands Help =========---
     admin -- Administration
     mvlan -- Management VLAN settings
      snmp -- SNMP settings
    backup -- Backup/Restore settings
    autorb -- Auto reboot settings
   fwgrade -- Firmware upgrade
      time -- Time settings
   wifisch -- Wifi schedule
       log -- Log
      diag -- Diagnostics
      disc -- Device Discovery
    logout -- Logout
      help -- Help
      exit -- Exit
ens202ext/mgmt>fwgrade
  Management --> Firmware upgrade
---========= Commands Help =========---
      fwup -- Firmware upgrade
      help -- Help
      exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin

Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
This commit is contained in:
Marty Plummer 2017-04-14 12:08:17 -05:00 committed by Piotr Dymacz
parent 0f21873f7f
commit 558d86923e
12 changed files with 180 additions and 1 deletions

View file

@ -27,6 +27,7 @@ cpe870|\
cr3000|\
cr5000|\
eap300v2|\
ens202ext|\
gl-ar300m|\
hornet-ub|\
hornet-ub-x2|\

View file

@ -220,6 +220,13 @@ eap300v2)
ucidef_set_led_netdev "lan" "LAN" "engenius:blue:lan" "eth0"
ucidef_set_led_wlan "wlan" "WLAN" "engenius:blue:wlan" "phy0tpt"
;;
ens202ext)
ucidef_set_rssimon "wlan0" "200000" "1"
ucidef_set_led_rssi "rssilow" "RSSILOW" "engenius:amber:wlan1" "wlan0" "1" "100" "0" "13"
ucidef_set_led_rssi "rssimedium" "RSSIMEDIUM" "engenius:red:wlan2" "wlan0" "25" "100" "-39" "13"
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "engenius:amber:wlan3" "wlan0" "50" "100" "-59" "13"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "engenius:green:wlan4" "wlan0" "75" "100" "-79" "13"
;;
f9k1115v2)
ucidef_set_led_usbdev "usb2" "USB2" "belkin:green:usb2" "1-1"
;;

View file

@ -175,6 +175,9 @@ get_status_led() {
eap300v2)
status_led="engenius:blue:power"
;;
ens202ext)
status_led="engenius:amber:power"
;;
eap7660d)
status_led="$board:green:ds4"
;;

View file

@ -625,6 +625,9 @@ ar71xx_board_detect() {
*"EmbWir-Dorin-Router")
name="ew-dorin-router"
;;
*"ENS202EXT")
name="ens202ext"
;;
*"EPG5000")
name="epg5000"
;;

View file

@ -236,6 +236,7 @@ platform_check_image() {
dr531|\
dragino2|\
ebr-2310-c1|\
ens202ext|\
epg5000|\
esr1750|\
esr900|\
@ -757,7 +758,8 @@ platform_do_upgrade() {
platform_do_upgrade_allnet "0x9f080000" "$ARGV"
;;
cap4200ag|\
eap300v2)
eap300v2|\
ens202ext)
platform_do_upgrade_allnet "0xbf0a0000" "$ARGV"
;;
dir-825-b1|\

View file

@ -100,6 +100,7 @@ CONFIG_ATH79_MACH_EAP300V2=y
CONFIG_ATH79_MACH_EAP7660D=y
CONFIG_ATH79_MACH_EL_M150=y
CONFIG_ATH79_MACH_EL_MINI=y
CONFIG_ATH79_MACH_ENS202EXT=y
CONFIG_ATH79_MACH_EPG5000=y
CONFIG_ATH79_MACH_ESR1750=y
CONFIG_ATH79_MACH_ESR900=y

View file

@ -767,6 +767,15 @@ config ATH79_MACH_EAP120
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_ENS202EXT
bool "EnGenius ENS202EXT support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_EAP300V2
bool "EnGenius EAP300 v2 support"
select SOC_AR934X

View file

@ -104,6 +104,7 @@ obj-$(CONFIG_ATH79_MACH_EAP300V2) += mach-eap300v2.o
obj-$(CONFIG_ATH79_MACH_EAP7660D) += mach-eap7660d.o
obj-$(CONFIG_ATH79_MACH_EL_M150) += mach-el-m150.o
obj-$(CONFIG_ATH79_MACH_EL_MINI) += mach-el-mini.o
obj-$(CONFIG_ATH79_MACH_ENS202EXT) += mach-ens202ext.o
obj-$(CONFIG_ATH79_MACH_EPG5000) += mach-epg5000.o
obj-$(CONFIG_ATH79_MACH_ESR1750) += mach-esr1750.o
obj-$(CONFIG_ATH79_MACH_ESR900) += mach-esr900.o

View file

@ -0,0 +1,124 @@
/*
* EnGenius ENS202EXT board support
*
* Copyright (C) 2017 Marty Plummer <netz.kernel@gmail.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include <linux/gpio.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/platform_device.h>
#include <asm/mach-ath79/ar71xx_regs.h>
#include <asm/mach-ath79/ath79.h>
#include "common.h"
#include "dev-eth.h"
#include "dev-gpio-buttons.h"
#include "dev-leds-gpio.h"
#include "dev-m25p80.h"
#include "dev-wmac.h"
#include "machtypes.h"
#include "nvram.h"
#define ENS202_GPIO_LED_WLAN4 0
#define ENS202_GPIO_LED_POWER 14
#define ENS202_GPIO_LED_WLAN2 16
#define ENS202_GPIO_LED_WLAN3 17
#define ENS202_GPIO_LED_WLAN1 18
#define ENS202_GPIO_BTN_RESET 1
#define ENS202_KEYS_POLL_INTERVAL 20 /* msecs */
#define ENS202_KEYS_DEBOUNCE_INTERVAL (3 * ENS202_KEYS_POLL_INTERVAL)
static struct gpio_led ens202_leds_gpio[] __initdata = {
{
.name = "engenius:amber:wlan1",
.gpio = ENS202_GPIO_LED_WLAN1,
.active_low = 1,
}, {
.name = "engenius:red:wlan2",
.gpio = ENS202_GPIO_LED_WLAN2,
.active_low = 1,
}, {
.name = "engenius:amber:wlan3",
.gpio = ENS202_GPIO_LED_WLAN3,
.active_low = 1,
}, {
.name = "engenius:green:wlan4",
.gpio = ENS202_GPIO_LED_WLAN4,
.active_low = 1,
}, {
.name = "engenius:amber:power",
.gpio = ENS202_GPIO_LED_POWER,
.active_low = 1,
}
};
static struct gpio_keys_button ens202_gpio_keys[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
.code = KEY_RESTART,
.debounce_interval = ENS202_KEYS_DEBOUNCE_INTERVAL,
.gpio = ENS202_GPIO_BTN_RESET,
.active_low = 1,
}
};
static void __init ens202_setup(void)
{
const char *nvram = (char *) KSEG1ADDR(0x1f040000);
u8 mac_buff[6];
u8 *mac = NULL;
u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
if (ath79_nvram_parse_mac_addr(nvram, 0x10000,
"ethaddr=", mac_buff) == 0) {
ath79_init_mac(ath79_eth0_data.mac_addr, mac_buff, 0);
ath79_init_mac(ath79_eth1_data.mac_addr, mac_buff, 1);
mac = mac_buff;
}
ath79_gpio_function_enable(AR934X_GPIO_FUNC_JTAG_DISABLE);
ath79_gpio_output_select(ENS202_GPIO_LED_POWER, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(ENS202_GPIO_LED_WLAN1, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(ENS202_GPIO_LED_WLAN2, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(ENS202_GPIO_LED_WLAN3, AR934X_GPIO_OUT_GPIO);
ath79_gpio_output_select(ENS202_GPIO_LED_WLAN4, AR934X_GPIO_OUT_GPIO);
ath79_register_leds_gpio(-1, ARRAY_SIZE(ens202_leds_gpio),
ens202_leds_gpio);
ath79_register_gpio_keys_polled(-1, ENS202_KEYS_POLL_INTERVAL,
ARRAY_SIZE(ens202_gpio_keys),
ens202_gpio_keys);
ath79_register_m25p80(NULL);
ath79_register_wmac(art + 0x1000, NULL);
ath79_register_mdio(1, 0);
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0 |
AR934X_ETH_CFG_SW_ONLY_MODE);
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
ath79_eth0_data.phy_mask = BIT(0);
ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
ath79_eth0_pll_data.pll_1000 = 0x06000000;
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
ath79_eth1_data.speed = SPEED_1000;
ath79_eth1_data.duplex = DUPLEX_FULL;
ath79_register_eth(0);
ath79_register_eth(1);
}
MIPS_MACHINE(ATH79_MACH_ENS202EXT, "ENS202EXT", "EnGenius ENS202EXT",
ens202_setup);

View file

@ -95,6 +95,7 @@ enum ath79_mach_type {
ATH79_MACH_EBR_2310_C1, /* D-link EBR-2310 rev. C1 */
ATH79_MACH_EL_M150, /* EasyLink EL-M150 */
ATH79_MACH_EL_MINI, /* EasyLink EL-MINI */
ATH79_MACH_ENS202EXT, /* EnGenius ENS202EXT */
ATH79_MACH_EPG5000, /* EnGenius EPG5000 */
ATH79_MACH_ESR1750, /* EnGenius ESR1750 */
ATH79_MACH_ESR900, /* EnGenius ESR900 */

View file

@ -17,6 +17,7 @@ include ./tp-link.mk
include ./ubnt.mk
include ./generic.mk
include ./legacy-devices.mk
include ./senao.mk
endif
ifeq ($(SUBTARGET),nand)
include ./nand.mk

View file

@ -0,0 +1,26 @@
define Build/senao-factory-image
$(eval board=$(word 1,$(1)))
$(eval rootfs=$(word 2,$(1)))
mkdir -p $@.senao
touch $@.senao/FWINFO-OpenWrt-$(REVISION)-$(board)
$(CP) $(IMAGE_KERNEL) $@.senao/openwrt-senao-$(board)-uImage-lzma.bin
$(CP) $(rootfs) $@.senao/openwrt-senao-$(board)-root.squashfs
$(TAR) -czf $@ -C $@.senao .
rm -rf $@.senao
endef
define Device/ens202ext
DEVICE_TITLE := EnGenius ENS202EXT
BOARDNAME := ENS202EXT
DEVICE_PACKAGES += rssileds
KERNEL_SIZE := 1536k
KERNEL := kernel-bin | patch-cmdline | lzma | uImage lzma | check-size $$(KERNEL_SIZE)
IMAGE_SIZE := 12096k
IMAGES += factory.bin
IMAGE/factory.bin/squashfs := append-rootfs | pad-rootfs | senao-factory-image ens202ext $$$$@
MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),320k(custom)ro,13632k(firmware),2048k(failsafe)ro,64k(art)ro
endef
TARGET_DEVICES += ens202ext