openwrtv3/target/linux/ar71xx/config-4.4

469 lines
13 KiB
Groff
Raw Normal View History

CONFIG_AG71XX=y
CONFIG_AG71XX_AR8216_SUPPORT=y
# CONFIG_AG71XX_DEBUG is not set
# CONFIG_AG71XX_DEBUG_FS is not set
CONFIG_AR8216_PHY=y
CONFIG_AR8216_PHY_LEDS=y
CONFIG_ARCH_BINFMT_ELF_STATE=y
CONFIG_ARCH_CLOCKSOURCE_DATA=y
CONFIG_ARCH_DISCARD_MEMBLOCK=y
CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
# CONFIG_ARCH_HAS_GCOV_PROFILE_ALL is not set
CONFIG_ARCH_HAS_RESET_CONTROLLER=y
# CONFIG_ARCH_HAS_SG_CHAIN is not set
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_ARCH_SUPPORTS_UPROBES=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARCH_USE_BUILTIN_BSWAP=y
CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
CONFIG_AT803X_PHY=y
CONFIG_ATH79=y
CONFIG_ATH79_DEV_AP9X_PCI=y
CONFIG_ATH79_DEV_DSA=y
CONFIG_ATH79_DEV_ETH=y
CONFIG_ATH79_DEV_GPIO_BUTTONS=y
CONFIG_ATH79_DEV_LEDS_GPIO=y
CONFIG_ATH79_DEV_M25P80=y
CONFIG_ATH79_DEV_NFC=y
CONFIG_ATH79_DEV_SPI=y
CONFIG_ATH79_DEV_USB=y
CONFIG_ATH79_DEV_WMAC=y
CONFIG_ATH79_MACH_A60=y
CONFIG_ATH79_MACH_ALFA_AP120C=y
CONFIG_ATH79_MACH_ALFA_AP96=y
CONFIG_ATH79_MACH_ALFA_NX=y
CONFIG_ATH79_MACH_ALL0258N=y
CONFIG_ATH79_MACH_ALL0315N=y
CONFIG_ATH79_MACH_ANTMINER_S1=y
CONFIG_ATH79_MACH_ANTMINER_S3=y
CONFIG_ATH79_MACH_ANTROUTER_R1=y
CONFIG_ATH79_MACH_AP121=y
CONFIG_ATH79_MACH_AP132=y
CONFIG_ATH79_MACH_AP136=y
CONFIG_ATH79_MACH_AP143=y
CONFIG_ATH79_MACH_AP147=y
CONFIG_ATH79_MACH_AP152=y
CONFIG_ATH79_MACH_AP531B0=y
# CONFIG_ATH79_MACH_AP81 is not set
CONFIG_ATH79_MACH_AP90Q=y
CONFIG_ATH79_MACH_AP96=y
ar71xx: add support to TP-Link Archer C59v1 and C60v1 TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-27 21:41:41 +00:00
CONFIG_ATH79_MACH_ARCHER_C59_V1=y
CONFIG_ATH79_MACH_ARCHER_C60_V1=y
CONFIG_ATH79_MACH_ARCHER_C7=y
CONFIG_ATH79_MACH_ARDUINO_YUN=y
CONFIG_ATH79_MACH_AW_NR580=y
CONFIG_ATH79_MACH_BHR_4GRV2=y
CONFIG_ATH79_MACH_BHU_BXU2000N2_A=y
CONFIG_ATH79_MACH_BSB=y
CONFIG_ATH79_MACH_C55=y
CONFIG_ATH79_MACH_C60=y
CONFIG_ATH79_MACH_CAP324=y
CONFIG_ATH79_MACH_CAP4200AG=y
CONFIG_ATH79_MACH_CARAMBOLA2=y
CONFIG_ATH79_MACH_CF_E316N_V2=y
CONFIG_ATH79_MACH_CF_E320N_V2=y
CONFIG_ATH79_MACH_CF_E380AC_V1=y
CONFIG_ATH79_MACH_CF_E380AC_V2=y
CONFIG_ATH79_MACH_CF_E520N=y
CONFIG_ATH79_MACH_CF_E530N=y
ar71xx: add support for P&W R602N and CPE505N P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-15 23:54:08 +00:00
CONFIG_ATH79_MACH_CPE505N=y
CONFIG_ATH79_MACH_CPE510=y
CONFIG_ATH79_MACH_CPE830=y
CONFIG_ATH79_MACH_CPE870=y
CONFIG_ATH79_MACH_CR3000=y
CONFIG_ATH79_MACH_CR5000=y
CONFIG_ATH79_MACH_DAP_2695_A1=y
CONFIG_ATH79_MACH_DB120=y
CONFIG_ATH79_MACH_DGL_5500_A1=y
CONFIG_ATH79_MACH_DHP_1565_A1=y
CONFIG_ATH79_MACH_DIR_505_A1=y
CONFIG_ATH79_MACH_DIR_600_A1=y
CONFIG_ATH79_MACH_DIR_615_C1=y
CONFIG_ATH79_MACH_DIR_615_I1=y
CONFIG_ATH79_MACH_DIR_825_B1=y
CONFIG_ATH79_MACH_DIR_825_C1=y
CONFIG_ATH79_MACH_DIR_869_A1=y
CONFIG_ATH79_MACH_DLAN_HOTSPOT=y
CONFIG_ATH79_MACH_DLAN_PRO_1200_AC=y
CONFIG_ATH79_MACH_DLAN_PRO_500_WP=y
CONFIG_ATH79_MACH_DOMYWIFI_DW33D=y
CONFIG_ATH79_MACH_DR344=y
CONFIG_ATH79_MACH_DR531=y
CONFIG_ATH79_MACH_DRAGINO2=y
CONFIG_ATH79_MACH_E2100L=y
CONFIG_ATH79_MACH_EAP120=y
CONFIG_ATH79_MACH_EAP300V2=y
CONFIG_ATH79_MACH_EAP7660D=y
CONFIG_ATH79_MACH_EL_M150=y
CONFIG_ATH79_MACH_EL_MINI=y
ar71xx: add support for EnGenius ENS202EXT EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
2017-04-14 17:08:17 +00:00
CONFIG_ATH79_MACH_ENS202EXT=y
CONFIG_ATH79_MACH_EPG5000=y
CONFIG_ATH79_MACH_ESR1750=y
CONFIG_ATH79_MACH_ESR900=y
CONFIG_ATH79_MACH_EW_DORIN=y
CONFIG_ATH79_MACH_F9K1115V2=y
CONFIG_ATH79_MACH_GL_AR150=y
CONFIG_ATH79_MACH_GL_AR300=y
CONFIG_ATH79_MACH_GL_AR300M=y
CONFIG_ATH79_MACH_GL_DOMINO=y
CONFIG_ATH79_MACH_GL_INET=y
CONFIG_ATH79_MACH_GL_MIFI=y
CONFIG_ATH79_MACH_GS_MINIBOX_V1=y
CONFIG_ATH79_MACH_GS_OOLITE=y
# CONFIG_ATH79_MACH_HIVEAP_121 is not set
CONFIG_ATH79_MACH_HIWIFI_HC6361=y
CONFIG_ATH79_MACH_HORNET_UB=y
CONFIG_ATH79_MACH_JA76PF=y
CONFIG_ATH79_MACH_JWAP003=y
CONFIG_ATH79_MACH_JWAP230=y
CONFIG_ATH79_MACH_LIMA=y
CONFIG_ATH79_MACH_MC_MAC1200R=y
CONFIG_ATH79_MACH_MR12=y
CONFIG_ATH79_MACH_MR16=y
CONFIG_ATH79_MACH_MR1750=y
CONFIG_ATH79_MACH_MR18=y
CONFIG_ATH79_MACH_MR600=y
CONFIG_ATH79_MACH_MR900=y
CONFIG_ATH79_MACH_MYNET_N600=y
CONFIG_ATH79_MACH_MYNET_N750=y
CONFIG_ATH79_MACH_MYNET_REXT=y
CONFIG_ATH79_MACH_MZK_W04NU=y
CONFIG_ATH79_MACH_MZK_W300NH=y
CONFIG_ATH79_MACH_NBG460N=y
CONFIG_ATH79_MACH_NBG6716=y
CONFIG_ATH79_MACH_OM2P=y
CONFIG_ATH79_MACH_OM5P=y
CONFIG_ATH79_MACH_OM5P_AC=y
CONFIG_ATH79_MACH_OM5P_ACv2=y
CONFIG_ATH79_MACH_OMY_G1=y
CONFIG_ATH79_MACH_OMY_X1=y
CONFIG_ATH79_MACH_ONION_OMEGA=y
CONFIG_ATH79_MACH_PB42=y
CONFIG_ATH79_MACH_PB44=y
CONFIG_ATH79_MACH_PQI_AIR_PEN=y
CONFIG_ATH79_MACH_QIHOO_C301=y
ar71xx: add support for P&W R602N and CPE505N P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-15 23:54:08 +00:00
CONFIG_ATH79_MACH_R602N=y
CONFIG_ATH79_MACH_R6100=y
# CONFIG_ATH79_MACH_RAMBUTAN is not set
# CONFIG_ATH79_MACH_RB2011 is not set
# CONFIG_ATH79_MACH_RB4XX is not set
# CONFIG_ATH79_MACH_RB750 is not set
# CONFIG_ATH79_MACH_RB91X is not set
# CONFIG_ATH79_MACH_RB922 is not set
# CONFIG_ATH79_MACH_RB95X is not set
# CONFIG_ATH79_MACH_RBSPI is not set
# CONFIG_ATH79_MACH_RBSXTLITE is not set
CONFIG_ATH79_MACH_RE450=y
CONFIG_ATH79_MACH_RW2458N=y
CONFIG_ATH79_MACH_SC1750=y
CONFIG_ATH79_MACH_SC300M=y
CONFIG_ATH79_MACH_SC450=y
CONFIG_ATH79_MACH_SMART_300=y
CONFIG_ATH79_MACH_SOM9331=y
ar71xx: add support for YunCore SR3200 and XD3200 YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-02 21:42:41 +00:00
CONFIG_ATH79_MACH_SR3200=y
CONFIG_ATH79_MACH_TELLSTICK_ZNET_LITE=y
CONFIG_ATH79_MACH_TEW_632BRP=y
CONFIG_ATH79_MACH_TEW_673GRU=y
CONFIG_ATH79_MACH_TEW_712BR=y
CONFIG_ATH79_MACH_TEW_732BR=y
CONFIG_ATH79_MACH_TEW_823DRU=y
CONFIG_ATH79_MACH_TL_MR11U=y
CONFIG_ATH79_MACH_TL_MR13U=y
CONFIG_ATH79_MACH_TL_MR3020=y
CONFIG_ATH79_MACH_TL_MR3X20=y
CONFIG_ATH79_MACH_TL_MR6400=y
CONFIG_ATH79_MACH_TL_WA701ND_V2=y
CONFIG_ATH79_MACH_TL_WA7210N_V2=y
CONFIG_ATH79_MACH_TL_WA801ND_V3=y
CONFIG_ATH79_MACH_TL_WA830RE_V2=y
CONFIG_ATH79_MACH_TL_WA850RE_V2=y
CONFIG_ATH79_MACH_TL_WA901ND=y
CONFIG_ATH79_MACH_TL_WA901ND_V2=y
CONFIG_ATH79_MACH_TL_WA901ND_V4=y
CONFIG_ATH79_MACH_TL_WAX50RE=y
CONFIG_ATH79_MACH_TL_WDR3320_V2=y
CONFIG_ATH79_MACH_TL_WDR3500=y
CONFIG_ATH79_MACH_TL_WDR4300=y
CONFIG_ATH79_MACH_TL_WDR6500_V2=y
CONFIG_ATH79_MACH_TL_WPA8630=y
CONFIG_ATH79_MACH_TL_WR1041N_V2=y
CONFIG_ATH79_MACH_TL_WR1043ND=y
CONFIG_ATH79_MACH_TL_WR1043ND_V2=y
CONFIG_ATH79_MACH_TL_WR1043ND_V4=y
CONFIG_ATH79_MACH_TL_WR2543N=y
CONFIG_ATH79_MACH_TL_WR703N=y
CONFIG_ATH79_MACH_TL_WR720N_V3=y
CONFIG_ATH79_MACH_TL_WR741ND=y
CONFIG_ATH79_MACH_TL_WR741ND_V4=y
CONFIG_ATH79_MACH_TL_WR802N_V1=y
CONFIG_ATH79_MACH_TL_WR802N_V2=y
CONFIG_ATH79_MACH_TL_WR810N=y
CONFIG_ATH79_MACH_TL_WR840N_V2=y
CONFIG_ATH79_MACH_TL_WR841N_V1=y
CONFIG_ATH79_MACH_TL_WR841N_V8=y
CONFIG_ATH79_MACH_TL_WR841N_V9=y
CONFIG_ATH79_MACH_TL_WR941ND=y
CONFIG_ATH79_MACH_TL_WR941ND_V6=y
CONFIG_ATH79_MACH_TL_WR940N_V4=y
CONFIG_ATH79_MACH_TUBE2H=y
CONFIG_ATH79_MACH_UBNT=y
CONFIG_ATH79_MACH_UBNT_UNIFIAC=y
CONFIG_ATH79_MACH_UBNT_XM=y
CONFIG_ATH79_MACH_WEIO=y
CONFIG_ATH79_MACH_WHR_HP_G300N=y
CONFIG_ATH79_MACH_WLAE_AG300N=y
CONFIG_ATH79_MACH_WLR8100=y
CONFIG_ATH79_MACH_WNDAP360=y
CONFIG_ATH79_MACH_WNDR3700=y
CONFIG_ATH79_MACH_WNDR4300=y
CONFIG_ATH79_MACH_WNR2000=y
CONFIG_ATH79_MACH_WNR2000_V3=y
CONFIG_ATH79_MACH_WNR2000_V4=y
CONFIG_ATH79_MACH_WNR2200=y
CONFIG_ATH79_MACH_WP543=y
CONFIG_ATH79_MACH_WPE72=y
CONFIG_ATH79_MACH_WPJ342=y
CONFIG_ATH79_MACH_WPJ344=y
CONFIG_ATH79_MACH_WPJ531=y
CONFIG_ATH79_MACH_WPJ558=y
CONFIG_ATH79_MACH_WPJ563=y
CONFIG_ATH79_MACH_WRT160NL=y
CONFIG_ATH79_MACH_WRT400N=y
CONFIG_ATH79_MACH_WRTNODE2Q=y
CONFIG_ATH79_MACH_WZR_450HP2=y
CONFIG_ATH79_MACH_WZR_HP_AG300H=y
CONFIG_ATH79_MACH_WZR_HP_G300NH=y
CONFIG_ATH79_MACH_WZR_HP_G300NH2=y
CONFIG_ATH79_MACH_WZR_HP_G450H=y
ar71xx: add support for YunCore SR3200 and XD3200 YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-02 21:42:41 +00:00
CONFIG_ATH79_MACH_XD3200=y
CONFIG_ATH79_MACH_Z1=y
CONFIG_ATH79_MACH_ZBT_WE1526=y
CONFIG_ATH79_MACH_ZCN_1523H=y
CONFIG_ATH79_NVRAM=y
CONFIG_ATH79_PCI_ATH9K_FIXUP=y
# CONFIG_ATH79_ROUTERBOOT is not set
CONFIG_ATH79_WDT=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_CEVT_R4K=y
CONFIG_CLKDEV_LOOKUP=y
CONFIG_CLONE_BACKWARDS=y
CONFIG_CMDLINE="rootfstype=squashfs,jffs2 noinitrd"
CONFIG_CMDLINE_BOOL=y
# CONFIG_CMDLINE_OVERRIDE is not set
CONFIG_COMMON_CLK=y
CONFIG_CPU_BIG_ENDIAN=y
CONFIG_CPU_GENERIC_DUMP_TLB=y
CONFIG_CPU_HAS_PREFETCH=y
CONFIG_CPU_HAS_SYNC=y
CONFIG_CPU_MIPS32=y
CONFIG_CPU_MIPS32_R2=y
CONFIG_CPU_MIPSR2=y
CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y
CONFIG_CPU_R4K_CACHE_TLB=y
CONFIG_CPU_R4K_FPU=y
CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
CONFIG_CPU_SUPPORTS_HIGHMEM=y
CONFIG_CPU_SUPPORTS_MSA=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_WORKQUEUE=y
CONFIG_CSRC_R4K=y
CONFIG_DMA_NONCOHERENT=y
CONFIG_DTC=y
CONFIG_EARLY_PRINTK=y
CONFIG_ETHERNET_PACKET_MANGLE=y
CONFIG_GENERIC_ATOMIC64=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_GENERIC_IO=y
CONFIG_GENERIC_IRQ_CHIP=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_SCHED_CLOCK=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GPIOLIB=y
CONFIG_GPIOLIB_IRQCHIP=y
ar71xx: add support to TP-Link Archer C59v1 and C60v1 TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-27 21:41:41 +00:00
CONFIG_GPIO_74X164=y
CONFIG_GPIO_DEVRES=y
# CONFIG_GPIO_LATCH is not set
CONFIG_GPIO_NXP_74HC153=y
CONFIG_GPIO_PCF857X=y
CONFIG_GPIO_SYSFS=y
CONFIG_HARDWARE_WATCHPOINTS=y
CONFIG_HAS_DMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT_MAP=y
# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
# CONFIG_HAVE_ARCH_BITREVERSE is not set
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
CONFIG_HAVE_BPF_JIT=y
CONFIG_HAVE_CC_STACKPROTECTOR=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_CLK_PREPARE=y
CONFIG_HAVE_CONTEXT_TRACKING=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_HAVE_DEBUG_KMEMLEAK=y
CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DMA_CONTIGUOUS=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
CONFIG_HAVE_KVM=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_HAVE_NET_DSA=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
CONFIG_HW_HAS_PCI=y
CONFIG_HZ_PERIODIC=y
CONFIG_I2C=y
CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_GPIO=y
CONFIG_IMAGE_CMDLINE_HACK=y
CONFIG_INITRAMFS_ROOT_GID=0
CONFIG_INITRAMFS_ROOT_UID=0
CONFIG_INITRAMFS_SOURCE="../../root"
CONFIG_IP17XX_PHY=y
CONFIG_IRQCHIP=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_IRQ_MIPS_CPU=y
CONFIG_IRQ_WORK=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_NU801=y
# CONFIG_LEDS_WNDR3700_USB is not set
CONFIG_LIBFDT=y
CONFIG_MARVELL_PHY=y
CONFIG_MDIO_BITBANG=y
CONFIG_MDIO_BOARDINFO=y
CONFIG_MDIO_GPIO=y
CONFIG_MICREL_PHY=y
CONFIG_MIPS=y
CONFIG_MIPS_CLOCK_VSYSCALL=y
# CONFIG_MIPS_CMDLINE_DTB_EXTEND is not set
CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER=y
# CONFIG_MIPS_CMDLINE_FROM_DTB is not set
# CONFIG_MIPS_ELF_APPENDED_DTB is not set
# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set
CONFIG_MIPS_L1_CACHE_SHIFT=5
CONFIG_MIPS_MACHINE=y
CONFIG_MIPS_NO_APPENDED_DTB=y
# CONFIG_MIPS_RAW_APPENDED_DTB is not set
CONFIG_MIPS_SPRAM=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_MTD_CFI_ADV_OPTIONS=y
CONFIG_MTD_CFI_GEOMETRY=y
# CONFIG_MTD_CFI_I2 is not set
# CONFIG_MTD_CFI_INTELEXT is not set
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CYBERTAN_PARTS=y
CONFIG_MTD_M25P80=y
# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
CONFIG_MTD_MYLOADER_PARTS=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-2
CONFIG_MTD_REDBOOT_PARTS=y
CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPLIT_FIRMWARE=y
CONFIG_MTD_SPLIT_LZMA_FW=y
CONFIG_MTD_SPLIT_SEAMA_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_MTD_SPLIT_WRGG_FW=y
CONFIG_MTD_SPLIT_MINOR_FW=y
CONFIG_MTD_TPLINK_PARTS=y
CONFIG_MYLOADER=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NEED_PER_CPU_KM=y
CONFIG_NET_DSA=y
CONFIG_NET_DSA_MV88E6060=y
CONFIG_NET_DSA_MV88E6063=y
CONFIG_NET_DSA_TAG_TRAILER=y
CONFIG_NET_SWITCHDEV=y
CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
# CONFIG_NO_IOPORT_MAP is not set
CONFIG_OF=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_ADDRESS_PCI=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_FLATTREE=y
CONFIG_OF_GPIO=y
CONFIG_OF_IRQ=y
CONFIG_OF_MDIO=y
CONFIG_OF_MTD=y
CONFIG_OF_NET=y
CONFIG_OF_PCI=y
CONFIG_OF_PCI_IRQ=y
CONFIG_PCI=y
CONFIG_PCI_AR724X=y
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
CONFIG_PCI_DOMAINS=y
CONFIG_PERF_USE_VMALLOC=y
CONFIG_PGTABLE_LEVELS=2
CONFIG_PHYLIB=y
CONFIG_RATIONAL=y
# CONFIG_RCU_STALL_COMMON is not set
CONFIG_RTL8306_PHY=y
CONFIG_RTL8366RB_PHY=y
CONFIG_RTL8366S_PHY=y
CONFIG_RTL8366_SMI=y
CONFIG_RTL8367_PHY=y
CONFIG_SCHED_HRTICK=y
# CONFIG_SCHED_INFO is not set
# CONFIG_SCSI_DMA is not set
# CONFIG_SERIAL_8250_FSL is not set
CONFIG_SERIAL_8250_NR_UARTS=1
CONFIG_SERIAL_8250_RUNTIME_UARTS=1
CONFIG_SERIAL_AR933X=y
CONFIG_SERIAL_AR933X_CONSOLE=y
CONFIG_SERIAL_AR933X_NR_UARTS=2
CONFIG_SOC_AR71XX=y
CONFIG_SOC_AR724X=y
CONFIG_SOC_AR913X=y
CONFIG_SOC_AR933X=y
CONFIG_SOC_AR934X=y
CONFIG_SOC_QCA953X=y
CONFIG_SOC_QCA955X=y
CONFIG_SOC_QCA956X=y
CONFIG_SPI=y
CONFIG_SPI_ATH79=y
CONFIG_SPI_BITBANG=y
ar71xx: add support to TP-Link Archer C59v1 and C60v1 TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-27 21:41:41 +00:00
CONFIG_SPI_GPIO=y
CONFIG_SPI_MASTER=y
# CONFIG_SPI_RB4XX is not set
# CONFIG_SPI_VSC7385 is not set
CONFIG_SRCU=y
CONFIG_SWCONFIG=y
CONFIG_SWCONFIG_LEDS=y
CONFIG_SYSCTL_EXCEPTION_TRACE=y
CONFIG_SYS_HAS_CPU_MIPS32_R2=y
CONFIG_SYS_HAS_EARLY_PRINTK=y
CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
CONFIG_SYS_SUPPORTS_MIPS16=y
CONFIG_SYS_SUPPORTS_ZBOOT=y
CONFIG_TICK_CPU_ACCOUNTING=y
CONFIG_USB_SUPPORT=y
CONFIG_USE_OF=y
CONFIG_ZONE_DMA_FLAG=0