Kernel 4.9 support was added about 2 weeks ago and we haven't seen any
major regression so far. This patch was not ported to kernel 4.9, this
needs some additional work:
821-serial-core-add-support-for-boot-console-with-arbitr.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When the kmod-at91-adc package is activated for the at91 target the new
option CONFIG_AT91_SAMA5D2_ADC is selectable and not handled. Add this
option to the kernel 4.9 configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Specifications:
- SoC: Qualcomm QCA9558 (720 MHz)
- RAM: 256MB
- Storage: 1MB NOR, 128 MB NAND flash
- Ethernet: 1x1000M
Installation:
1. Connect to serial console on the board
2. Boot initramfs image over u-boot
3. Copy image to the device and run sysupgrade
Installation without serial console is not supported at this time
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kernel 4.9 is now working on the brcm47xx boards, we just recently fixed
the problem that some boards did not boot at all, by changing the memory
regions used to relocate the kernel to in the loader.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When porting the kernel patches from 4.4 to 4.9, they were missing a
small chunk that ensures that ftrace sections are kept in the vmlinux
image, even when linked with --gc-sections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ARV752DPW22 has the same generic mac address in the EEPROM as it
was already noticed for other lantiq boards using a ralink wireless.
Use the base mac address from the boardconfig partition as it is done
by the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds support for kernel 4.9 and replaces the kernel 4.4 support.
These are lynxis test results:
panda-board a3 - works, but no network, but master/4.4 doesn't have network either.
panda-board-a4 - u-boot SPL refuse to boot.
beaglebone-black - works
beagle-board - usb attached network doesn't come up and I doesn't have a serial around.
beagle-board-xm - ToDo: image code is missing.
Kernel 4.4 does not look better, so we merge this anyway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Alexander Couzens <lynxis@fe80.eu>
This reverts commit 13e5e47369.
This commit causes a severe regression in LAN->WAN routing performance
for several devices. This appears to be caused by the extra requirement
to validate the SKB checksum early in the rx path, which the ethernet
hardware does not do
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The build system took the DTB_SIZE definition from Default and not from
production-dtb under some conditions. Move the size definitions to
Default now as it is only used in production-dtb anyway.
Thanks Mathias Kresin for helping me with this.
Fixes: c2f052acae ("at91: convert boards to generic build target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These options where deactivated in the malta kernel, take the default
options form the generic kernel configuration now to better match the
other targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).
Now you can move a device from an ADSL/ATM port to an VDSL/PTM port
without any configuration changes for example.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[use the dsl0 interface name for the default netdev trigger in 01_led,
add ip dependency]
Signed-off-by: Mathias Kresin <dev@kresin.me>
It is unclear why so many packages are selected for ClearFog Base compared
to its big brother, and there is no reason to not append metadata for Base.
Tidy this up as the only hardware difference between Base/Pro is the
presence of a switch and a different board name / device tree.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Remove redundancy for platform_do_upgrade_clearfog
Fix platform_copy_config_clearfog to reflect -base/-pro split
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This module from Laird includes the following:
- CPU Atmel SoC SAMA5D31
- Wifi QCA6004
- Bluetooth CSR8811
- RAM 64MB LPDDR
- FLASH 128MB
The flash is a dual image layout, kernel a/b, rootfs a/b, and a user
partition.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
This module from Laird includes the following:
- CPU Atmel SoC ARM926EJS
- Wifi AR6003
- Bluetooth CSR8510
- RAM 64MB LPDDR
- FLASH 128MB
The flash is a dual image layout, kernel a/b, rootfs a/b, and a user
partition.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Instead of applying global defaults based on selected board, transition
to using a per board setting for UBIFS and UBINIZE.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
The platform generates squashfs images in a UBI block but misses the
kernel module to be able to mount the block.
DMA is also enabled to allow systems which include them in the DTS to
use it.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 4 PoE out)
- Outdoor use ready
This ethernet router is based on the same platform as the hEX PoE lite.
Installation
1. login to the Mikrotik WebUI to backup your licence keys
2. setup a DHCP/BOOTP Server with:
* DHCP-Option 66 (TFTP server name) pointing to a local TFTP
Server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. connect the port labled internet to your local network
4. keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
Server. Login as root/without password to the started LEDE via ssh
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
* rbcfg set boot_protocol bootp
* rbcfg set boot_device ethnand
* rbcfg apply
Open Netinstall and reboot routerboard. Now netinstall sees routerboard
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kimax U-25AWF-H1 is is a 2,5" HDD Enclosure with Wi-Fi/Eth conection
and battery, based on MediaTek MT7620A.
Patch rewritten from: https://forum.openwrt.org/viewtopic.php?pid=305643
Specification:
- MT7620A CPU
- 64 MB of RAM
- 16 MB of FLASH
- 802.11bgn WiFi
- 1x 10/100 Mbps Ethernet
- USB 2.0 Host
- UART for serial console
Flash instruction:
1. Download lede-ramips-mt7620-u25awf-h1-squashfs-sysupgrade.bin
2. Open webinterface a upgrade
3. After boot connect via ethernet to ip 192.168.1.1
Signed-off-by: Daniel Kucera <daniel.kucera@gmail.com>
[fix reset button gpio, don't add a lan/wan vlan config for single
port board, add -H1 suffix do make sure that this revision of the
board is supported/tested]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following adds the Aerohive HiveAP-330 Access Point to LEDE under
the mpc85xx/p1020 subtarget.
Hardware:
- SoC: Freescale P1020NSE2DFB
- NAND: Intel JS28F512M29EWH 64MB
- Memory: 2x ProMOS V59C1G01168QBJ3 128MB (Total of 256MB)
- 2.4GHz WiFi: Atheros AR9390-AL1A
- 5.0GHz WiFi: Atheros AR9390-AL1A
- Eth1: Atheros AR8035-A PoE
- Eth2: Atheros AR8035-A
- TPM: Atmel AT97SC3204
- LED Driver: TI LP5521
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a
password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, tftp boot the initramfs image:
dhcp;
tftpboot 0x1000000 192.168.1.101:lede-
mpc85xx-p1020-hiveap-330-initramfs.zImage;
tftpboot 0x6000000 192.168.1.101:lede-mpc85xx-p1020-hiveap-330.fdt;
bootm 0x1000000 - 0x6000000;
3. Once booted, scp over the sysupgrade file and sysupgrade the device
to flash LEDE to the NAND.
sysupgrade /tmp/lede-mpc85xx-p1020-hiveap-330-sysupgrade.img
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch adds a new kernel option called CONFIG_CMDLINE_OVERRIDE. This
setting is for devices with locked down u-boot environments, where users
are unable to change the default bootargs. When set, the fdt driver will
propagate the cmdline for the kernel from chosen/bootargs-override
instead of chosen/bootargs as long as it exists within the DTB.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The following patch enables building of initramfs images by default for
the P1020 subtarget in mpc85xx.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Add ext4 filesystem for creating sdcard image with ext4 rootfs and
removing ext2 as it superset of ext4.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Enabled SDHCI for sama5 in kernel default config and this is needed
to mount sdcard rootfs partition during boot.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
This PHY requires some extra programming to work reliably with all
devices. Backport upstream fix for it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is no requirement and plan to support 32-bit for ls1088ardb
and ls2088ardb. Current 32-bit firmware for them couldn't work,
so only keep 64-bit support for these two boards in menuconfig.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
When build firmware for layerscape target with CONFIG_ALL_NONSHARED=y,
there would be a compile issue of usb ehci-fsl driver. Actually this
driver was for PPC platforms initially and was not ready for non-PPC
now, but a kernel kconfig patch removed PPC dependency for it. So that
kernel patch should be reverted.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This add support for kernel 4.9 to the ar71xx target.
It was compile tested with the generic, NAND and mikrotik subtarget.
Multiple members of the community tested it on their boards and did not
report any major problem so far.
Especially the NAND part received some changes to adapt to the new
kernel APIs. The serial driver hack used for the Arduino Yun was not
ported because the kernel changed there a lot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
By default we are reusing the stack provided by CFE, like it is intended
by CFE. On my WRT54GS it is located at 0x8043BF30, so a big kernel image
could overwrite it. Relocate it to a different memory region which is
still under the 8MB RAM, but in the higher area. We only need this
memory region for the stack of the loader, Linux will set up this
for its own.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The boot process on a WRT54GL works the following way:
1. CFE gets loaded by the boot rom from flash
2. CFE loads the loader from the flash and gzip uncompresses it
3. CFE starts the loader
4. The loader stores the FW arguments and relocates itself to
BZ_TEXT_START (now 0x80600000)
5. The loader reads the Linux image from flash
6. The loader lzma decompresses the Linux image to LOADADDR (0x80001000)
7. The loader executes the uncompress Linux image at LOADADDR
The BZ_TEXT_START was set to 0x80400000 before. When the kernel gets
uncompressed and is bigger than BZ_TEXT_START - LOADADDR it overwrote
the loader which was currently uncompressing it and made the board
crash. Increase the BZ_TEXT_START my 2 MB to have more space for the
kernel. Even on 16MB RAM devices the memory goes till 0x80FFFFFF so this
should not be a problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The tplink 841n v13 requires an tplink v2 image header in
front of an initramfs image.
To boot an initramfs image:
- break the uboot by holding the '4' key
- setup your tftp server 192.168.0.255
- tftp 81000000 lede-ramips-mt76x8-tl-wr841n-v13-initramfs-kernel.bin
- bootm
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Enable dwmac-sun8i Ethernet core to use the built-in FastEthernet port.
Enable exposed UART, USB and I2C pins.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The lantiq patch 0028-NET-lantiq-various-etop-fixes.patch and sunxi
patch 0051-stmmac-form-4-11.patch no longer applied after applying the
the "generalize napi_complete_done()" patch.
Update them so they apply, and refresh patches while at it.
Fixes: 9aeb7ce8dc ("generic: net: generalize napi_complete_done")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Backport upstream commit that improves ethernet performance by a
small amount.
Compile and run tested on ipq8065.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
These options are deactivating some kernel modules for IP blocks not
uses on this SoC. I saw the same when working with the ARM64 Marvell
board so it is better to move them to generic.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Layerscape uses Cortex-A53 or Cortex-A72 CPU. It's proper
to set below CPU_TYPE for 32-bit mode.
CPU_TYPE:=cortex-a15
CPU_SUBTYPE:=neon-vfpv4
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add linux 4.9 support for layerscape.
All these kernel patches are from NXP LSDK 1709 release.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Rename subtargets 32b/64b with armv8_32b/armv8_64b which are
more proper, and update makefile files. There also will be other
subtargets added in the future, like armv7.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Under heavy load it's possible to overrun the 82574L. When this
happens, Other Interrupt happens and that's erroneously interpreted
as a Link Status Change.
http://patchwork.ozlabs.org/patch/792260/
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
A default rssileds config exists for the TP-Link WA850RE v1 but the
rssiled package is not included by default.
The compressed 17.01.3 image size increases by 3302 bytes which should
be tolerable even for a 4MB flash board.
Fixes: FS#1043
Signed-off-by: Mathias Kresin <dev@kresin.me>
With kernel commit 7630ea4bda18 ("Documentation: net: phy: improve
explanation when to specify the PHY ID") the purpose of using phy id
specific compatibles was clarified.
Remove the phy id specific compatibles since they are meant to be used
if the phy reports an incorrect or no phy id at all.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The generic nand driver fails to load with:
gen_nand 14000000.nand-parts: platform_nand_data is missing
gen_nand: probe of 14000000.nand-parts failed with error -22
and the xway-nand driver is used afterwards.
Drop the gen_nand compatible to get rid of the error message.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Refresh patches.
Compile-tested on brcm2708/bcm2708, octeon and x86/64.
Runtime-tested on brcm2708/bcm2708, octeon and x86/64.
Fixes the following CVEs:
- CVE-2017-1000252
- CVE-2017-12153
- CVE-2017-12154
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Evaluation board 2.2 uses a different status LED pin
The other removed LEDs were never present
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Handle AR9344 as well. Disable the EHCI platform device when device mode
is active, to avoid resource conflicts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This patch adds all the board-specific values currently hardcoded
in mktplinkfw2.c back to the respective device declarations in the
makefiles.
The rationale is to avoid modifying the source code every time a
new board or board variant is added.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Keep Archer C20 Power LED in the same state as it was configured by
bootloader (keep it hightlighed) to avoid unexpectable LED turning off
during kernel boot.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Add the missing USB related kernel config options to target config.
Enable wireless as well, wireless is supported via USB.
Fixes compile/packaging errors with the libertas wireless kernel
module.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not disable SPI in the subtarget, otherwise the SPI driver can not
be used.
Disable SPI by default and enable it in the board specific device tree
source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
AmazonSE and Falcon do not have support for PCI and it can't be
unselected in the subtarget kernel config. This way the enabled PCI
support is inherit from the higher level config to the subtarget.
If CONFIG_PCI is selected, PCI_SUPPORT will be autoselected as well and
all packages depending on this config symbol will be build and at least
some of them fail due to missing pci functions.
The issue can be observed if all kmods and all non-shared packages are
build. Fix the issue by enabling PCI support only in subtargets with
PCI support.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The subtarget kernel config options CONFIG_CC_OPTIMIZE_FOR_SIZE and
CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK are already set by the target or
global kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_SPI_LANTIQ was replaced by CONFIG_SPI_LANTIQ_SSC with the switch
to the upstreamed driver.
All other removed subtarget kernel config options are already set by
the target specific or global kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_MTSCHED & CONFIG_PERFCTRS were never defined in the kernel.
CONFIG_LANTIQ_PHY was replaced by CONFIG_INTEL_XWAY_PHY with the switch
to the upstreamed driver.
Add autoselected dependecies to the kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_GPIO_DEVRES was removed with kernel commit f9c22ec6c1c5 ("gpio:
Remove GPIO_DEVRES option") during kernel 4.9 development.
CONFIG_HAVE_BPF_JIT was removed with kernel commit 6077776b5908 ("bpf:
split HAVE_BPF_JIT into cBPF and eBPF variant") during kernel 4.7
development.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following features are working and tested:
* both Ethernet ports
* MMC
* LED
The following features are not working:
* Wifi (There is a crappy driver we could port)
* SPI flash (I haven't looked into this)
I haven't tried out the rest.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
check if the config option CONFIG_LANTIQ is defined.
This fixes the following warning:
CC [M] drivers/misc/owl-loader.o
drivers/misc/owl-loader.c: In function 'ath9k_pci_fixup':
drivers/misc/owl-loader.c:92:5: warning: "CONFIG_LANTIQ" is not defined [-Wundef]
#if CONFIG_LANTIQ
^
Fixes: e9401a2335 ("kernel: owl-loader for delayed Atheros ath9k fixup")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the device tree changes needed to make the GMAC stmmac driver
working for the Allwinner H3 SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the device tree changes needed to make the GMAC stmmac driver
working for the Allwinner A64 SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the GMAC which is use in the A64 and other
Allwinner chips by backporting the changes from the kernel versions
4.13.
Some commits are not backported which are adding support for newly
introduced APIs which are not available in kernel 4.9.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Booting from jffs2 directly is no longer supported, use
rootfstype=squashfs consistently for all subtargets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d
Improvements:
- Remove software watchdog as hardware watchdog now working as per
commit 3fbf3ab44f for all mt7621
devices.
- Reset button polarity corrected - length of press determines reboot
(short press) vs. reset to defaults (long press) behaviour.
- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
link and blink on activity. Green LEDs driven directly by switch
indicating any link speed and tx activity.
- USB port power on/off GPIO exposed as 'usbpower'
- Add access to uboot environment settings for checking/setting uboot
boot order preference from user space.
Changes:
- Front LED indicator is physically made of independent Yellow/Amber,
Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
indicator, hence the colour behaviour is similar to an RGB LED. RGB
LEDs are not supported at this time because they produce colour results
that do not then match colour labels, e.g. enabling 'mir3g:red' and
'mir3g:blue' would result in a purple indicator and we have no such
label for purple.
The yellow, red & blue LEDs have been split out as individual yellow,
red & blue status LEDs, with yellow being the default status LED as
before and with red's WAN and blue's USB default associations removed.
- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
layout. eth0.1 is LAN, eth0.2 is WAN
- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
leakage between kernel switch init and uci swconfig
uboot behaviour & system 'recovery'
uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed
last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2. last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok. If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.
NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.
Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.
Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.
Installation - from stock.
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot
Recovery - to stock.
Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)
Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'
All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot
The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted. Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The RT5350F's second UART pins are available on the base module and on
the EVB as well, so enable it in the device tree.
In order to keep the origian serial port numbering (ttyS0 is the serial
console), aliases added for the UART devices.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The RT5350F i2c pins is available on the base module and on
the EVB as well, so enable it in the dts.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The polarity of WLAN_ACT LED on the base module needs to inverted
in order to be 'on' when the WiFi interface is active
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The RT5350F-OLINUXINO(-EVB).dts files' content are nearly the same, so to avoid
code duplication this patch creates RT5350F-OLINUXINO.dtsi file which
covers the base board's features. The corresponding RT5350F-OLINUXINO.dts
just includes the new .dtsi and the RT5350F-OLINUXINO-EVB.dts adds the EVB
specific GPIO config.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The Xiaomi Mi Router 3G uses this deranged vlan portmap. Add support so
that packets are not leaked across all switch ports when reset.
Fix a whitespace nit while we're here.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[fix wrong pvids order]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Disable VLANs on mt7621 boards with mt7530 switches on failsafe entry.
Allows failsafe networking to work correctly.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[fixed default case syntax error]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit 31e9445b7e.
"Linksys E1200 V1" is not a valid board name, as the brcm47xx arch code
can not detect this device. Stefan Lippers-Hollmann also found a typo in
this patch "cybetran" instead of "cybertan".
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[replaced u-boot patch with original version from u-boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
x86_64 platforms typically don't lack memory, so don't needlessly
economize memory if fq_codel on capable platforms.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
[Add a comment to the patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mediatek MT7621 soc watchdog DTS id was renamed from "mtk,mt7621-wdt" to
"mediatek,mt7621-wdt" when driver upstreamed to kernel 4.5
Update mt7621.dtsi & mt7628an.dtsi definitions to match upstreamed
kernel.
Restores hardward watchdog functionality on mt7621 devices under linux
4.9
Tested on: MIR3G
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Refresh patches.
Compile-tested on octeon and x86/64.
Runtime-tested on octeon and x86/64.
Fixes the following CVEs:
- CVE-2017-14106
- CVE-2017-14497
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support for SAMA5D4 with target device as at91-sama5d4_xplained
in SAMA5 subtarget and build images for SAMA5D4 Xplained board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D2 with target device as at91-sama5d2_xplained
in SAMA5 subtarget and build images for SAMA5D2 Xplained board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Renaming at91 subtarget sama5d3 to sama5 and using at91-sama5d3_xplained
as a target device in sama5 subtarget.This will enable to add other
sama5d2 & sama5d4 target devices in sama5 subtraget.This will avoid
code duplication when sama5d2 & sama5d4 added as different subtarget.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
This adds initial support for the A64 Allwinner SoC to LEDE.
It will be build in the new cortexa53 subtarget.
Currently it only supports the pine64 and the image is able to boot on
this SoC.
Camera, Ethernet, HDMI and other parts are currently not working.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports some more patches from kernel 4.11 adding more devices
to the device tree of the A64 SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports multiple patches from kernel 4.10 which are adding
missing support for the A64 and the pine64 board. These are the device
tree files, the pinctlk and the clock driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required to support kernel 4.9.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
[rewrite commit message (subject <= 50 characters)]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refresh patches.
Compile-tested on ipq8065/nbg6817 and x86/64.
Runtime-tested on ipq8065/nbg6817 and x86/64.
Fixes CVE-2017-1000251.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[adapt qcom_nandc.c patches to match upstream changes, test ipq8065/nbg6817]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Delete a bunch of fixes that are already included.
Refresh patches.
Compile-tested on malta/mipsel
Runtime-tested on malta/mipsel
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
4.4.80+ contains 71a165f6397df07a06ce643de5c2dbae29bd3cfb, 4.9.41+ contains
6c78197e4a69c19e61dfe904fdc661b2aee8ec20 which are all backports of upstream
commit 0878fff1f42c18e448ab5b8b4f6a3eb32365b5b6 ("net: phy: Do not perform
software reset for Generic PHY").
Our local patch is no longer needed, all this patch was doing was utilizing
gen10g_soft_reset which does nothing either, so just keep the code unchanged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We will be prompted with this config symbol when performance monitoring is
enabled in the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The factory partition of the Phicomm K2P contains two MAC addresses.
The lower MAC address is at offset 0xe006 and the higher one is at
offset 0xe000.
Use the lower MAC address as base mac-address which the switch driver
increments by one for the second (wan) vlan.
The MAC addresses are still inverted in contrast to the stock firmware
where the lower MAC address is used for wan. But at least the use of a
MAC address not intended/reserved for this particular board is fixed.
Signed-off-by: Jiawei Wang <me@jwang.link>
In commit b11c51916c ("ramips: Improve Sanlinking D240 config") I made
a mistake with regards GPIO numbering. And in addition to specifying the
wrong GPIO for controling the power of one of the mini-PCIe, I recently
discovered that the power of both slots can be controlled.
This patch specifies the correct GPIO for the left-most mini-PCIe slot
of the D240 (labeled power_mpcie2 since the slot is attached to SIM2),
and adds a GPIO that can be used to control the power of the other
mini-PCIe slot (labeled power_mpcie1).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[do not use the gpio active macros for the gpio-export value]
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link Archer C20 v1 is a router with 5-port FE switch and
non-detachable antennas. It's very similiar to TP-Link Archer C50.
Also it's based on MediaTek MT7620A+MT7610EN.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 8x LED (GPIO-controlled*), 2x button, power input switch
- 1 x USB 2.0 port
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the blue part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash. So, to flash this device we must
to prepare image using original firmware from tp-link site with uboot.
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot.
There are two ways to flash the device to LEDE:
1) Using tftp mode with UART connection and original LEDE image
- Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp
server directory
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, power up the router and press
key "4" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
setenv serverip 192.168.0.66
tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
- After that the device will reboot and boot to LEDE
2) Using tftp mode without UART connection but require some
manipulations with target image
- Download and unpack TP-Link Archer C20 v1 firmware from original web
site
- Split uboot.bin from original firmware by this command (example):
dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1
- Create ArcherC20V1_tp_recovery.bin using this command:
cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin
- Place ArcherC20V1_tp_recovery.bin in tftp server directory.
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
- Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
The implementation is not efficient on ar8xxx switches. It triggers high
CPU load and degrades device performance.
The high CPU load has been traced down to the ar8xxx_reg_wait() call in
ar8xxx_mib_op(), which has to usleep_range() till the MIB busy flag set
by the request to update the MIB counter is cleared.
This commit removes the get_port_stats() code introduced in 4d8a66d and
leaves a note for future hacker's beware.
Fixes: FS#1004
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.
Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The ZBT WE1026-5G
(http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up
to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the
ZBT WE826 image could be used. However, as the name implies, the -5G
comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz
radio, the addition of 5GHz means that a separate image is needed for
the WE1026-5G. I suspect that this image will also work on the previous
WE1026, but I don't have a device to test with.
The WE1026-5G has following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x 5GHz wifi (MT7612)
* 1x button.
* 3x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working:
* The 5GHz WIFI LED is completely dead. I suspect the issue is the same
as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is
controlled by the driver, and mt76 (currently) does not support this.
Not tested:
* SD card reader.
Notes:
* The modem (labeled 3G/4G) and power LEDs are controlled by the
hardware.
* There is a 32MB version of this device available, but I do not have
access to it. I have therefor only added support for the 16MB version,
but added all the required infrastructure to make adding support for the
32MB version easy.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the
reset button pressed for ~5sec when booting to start the web server. Set the
address of the network interface on your machine to 192.168.1.2/24, and
point your browser to 192.168.1.1 to access the recovery UI. From the
recovery UI you can upload a firmware image.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
On a TL-WN710N, this patch increases iperf performance from ~92.5 to ~93.5 mbps. Keep in mind the WN710N is a 100mbps device. I expect greater numbers from gigabit devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The cns3xxx interrupt controller uses a single register and as such
the 'mask' reg/functions must be used as opposed to the 'enable'/'disable'
reg/functions.
This fixes an issue that occurs if more than one GPIO on a specific controller
(there is GPIOA and GPIOB each having 32 GPIO's) uses interrupts. When one
would get enabled all others would be disabled prior to this patch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches.
Compile-tested on octeon and x86/64.
Runtime-tested on octeon and x86/64.
Fixes CVE-2017-11600.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This adds metadata to wpj344 and wpj558 images to prevent loading
firmware of wpj344 into wpj558 and vice versa. This until now was
possible and break the units and had to be recovered from the uboot.
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9882.
Short specification:
- 2x 10/100 Mbps Ethernet, with PoE support
- 64MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
[whitespace fixes, ac radio caldata offset fix]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
For the Archer C50v1, the EU and US versions are differentiated by their
respective HW additional version (0x0 for US, 0x2 for EU).
The stock web interface checks this field before flashing, making it
impossible to flash the current (US) factory image on EU hardware.
However the bootloader does not check this field, making it possible to use
a single sysupgrade image for both hardware.
This patch adds the necessary build bits to generate both EU and US factory
images, and renames the target as "Archer C50v1" since there are as of now
3 different versions of Archer C50 (all with different CPUs).
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.
Not tested:
* SD card reader.
Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
In case the link changes from down to up, the register is only updated
on read. If the link failed/was down, this bit will be 0 until after
reading this bit again.
Fixes a reported link down by swconfig alebit the link is up (query for
the link again will show the correct link status)
Signed-off-by: Mathias Kresin <dev@kresin.me>
In conditions where none of the switch ports is connected during boot,
the priv->port[i].link != priv->port[i].phydev->link condition is false
since both link values are equal (false). The carrier of the switch
netdev is never set to off and the link state reported by ip is UNKNOWN.
Turn the carrier off if none of the switch ports has a link, regardless
whether something has been changed. Add a check for a carrier to
prevent unnecessary calls to netif_carrier_off() if the carrier is
already off.
Based on a patch send by Martin Schiller.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 77645ffcd9 ("ramips: add support for the GnuBee Personal Cloud
One") dropped the execution permission from 01_leds with the result
that the file isn't started during first boot and no default LED
configuration is added.
Revert the introduced file permission change.
Fixes: FS#979
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[cherry picked the fix from a board support patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WAN port on the Netgear WNDR4300 router has two LEDs,
amber and green. Use the switch LED trigger to behave as the
rest of the LAN HW controlled LEDs
- Green: 1 Gbps
- Amber: 100/10 Mbps
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
1. Add support to LAN/WAN LEDs attached to ar8327.
2. Fix the problem that LAN/WAN LEDs does not blink in hardware (auto)
mode when connected to 10M/100M ethernet.
Signed-off-by: Kuang Rufan <master@a1983.com.cn>
Refresh patches.
Compile-tested on ramips/mt7621 and x86/64.
Runtime-tested on ramips/mt7621 and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This generic structure defines tx_bytes and rx_bytes as unsigned long (u32),
while several devices would typically report unsigned long long (u64).
The code can work as is, but there's a chance that with a sufficiently fast
interface the overflow might happen too fast to be correctly noticed by the
consumers of this data.
This patch makes both field unsigned long long and updates the only known
consumer of this data: swconfig_leds.c
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
The implementation uses a generic callback that select the correct MIB counter
index based on chip version.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite).
Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi"
They are essentially a single subtarget.
This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* fixes default affinity
* adds a napi watchdog - we were seeing stalled TX queues
* adds up/down locking
Signed-off-by: John Crispin <john@phrozen.org>
Install kmod-rt2800-pci instead of only the rt2x00 library.
Fixes missing wireless interface on AudioCodes AC-MP252.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Neon and vfpv4 support are activated by GCC on all ARMv8 CPUs because
this is now a mandatory part of the architecture. There is not need to
activate is manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Comtrend AR-5315u router
This a BCM6318 based board, 64 MB RAM, 16 MB SPI flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1
USB host port
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: refreshed patch]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This commit adds support for Xiaomi Mi WiFi Router 3G.
Short specification:
- MT7621AT + MT7603EN + 7612EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+2 x 1000M Ethernet
- 1x USB 3.0 port
- reset button
- yellow, blue, red leds
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: mtd erase kernel0
- run: reboot
Originally stock firmware has following partitions:
- ...
- kernel0 (primary kernel image)
- kernel1 (secondary kernel image, used by u-boot in failsafe routine)
- rootfs0 (primary rootfs)
- rootfs1 (secondary rootfs in case primary fails)
- overlay (used as ubi overlay)
This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so
it can be used by LEDE fully for package installation, resulting in 117,5MiB.
This device lacks hw watchdog, so adding softdog instead (stock does the same).
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The Gateworks System Controller (GSC) mimics a standard AD7418 device on
I2C bus 0 at slave 0x29.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches.
Adapt 704-phy-no-genphy-soft-reset.patch.
Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch.
Compile-tested on brcm2708/bcm2708 and x86/64.
Runtime-tested on brcm2708/bcm2708 and x86/64.
Fixes the following vulnerabilities:
- CVE-2017-7533
- CVE-2017-1000111
- CVE-2017-1000112
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The VoCore2 Lite uses the same PCB as the Vocore2.
This patch moves the common VoCore2 parts into dtsi.
Removed memory node in the device tree source file.
Memory is detected automatically.
http://vocore.io/http://vonger.net/http://vonger.cn/
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H
- Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG
- Wireless: Built into MT7688AN with onboard IPEX connector
Firmware installation:
- VoCore2-Lite ships with firmware forked from OpenWrt.
- Installation from the bootloader is recommended.
- If using luci/sysupgrade use the -n option (do not keep settings)
original firmware uses a modified proprietary MediaTek wireless driver.
- The wireless is disabled by default in LEDE.
- If reverting to factory firmware using the bootloader is recommended.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Tested by: Noble Pepper <noblepepper@gmail.com>
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.
Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.
Fixes: FS#670
Signed-off-by: Mathias Kresin <dev@kresin.me>
USB doesn't work in some danube boards because otg_cap
is missing since previous changes made on the USB-dwc2
lantiq driver. Fix it.
Tested on the ARV7518PW router.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.
This patch fixes the MAC address for wlan2g in line with OFW.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that
ATM should be used for ADSL and PTM for VDSL.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This makes it possible to simply add additional notification handlers
by putting new scripts in the /etc/hotplug.d/dsl directory.
the following Environment Variables are used:
(values marked with an * are only available when bonding support is
compiled in)
DSL_NOTIFICATION_TYPE with one of these values:
- DSL_STATUS
- DSL_INTERFACE_STATUS
- DSL_DATARATE_STATUS_US
- DSL_DATARATE_STATUS_DS
DSL_LINE_NUMBER=<0|1> *
If DSL_NOTIFICATION_TYPE == DSL_STATUS, these variables are set:
- DSL_XTU_STATUS=<ADSL|VDSL>
- DSL_TC_LAYER_STATUS=<ATM|EFM>
- DSL_EFM_TC_CONFIG_US=<NORMAL|PRE_EMPTION>
- DSL_EFM_TC_CONFIG_DS=<NORMAL>
If DSL_NOTIFICATION_TYPE == DSL_INTERFACE_STATUS, these variables are
set:
- DSL_INTERFACE_STATUS=<DOWN|READY|HANDSHAKE|TRAINING|UP>
- DSL_BONDING_STATUS=<INACTIVE|ACTIVE> *
If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_US, these variables are
set:
- DSL_DATARATE_US_BC0=<Upstream data rate in bit/s for Channel 0>
- DSL_DATARATE_US_BC1=<Upstream data rate in bit/s for Channel 1> *
If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_DS, these variables are
set:
- DSL_DATARATE_DS_BC0=<Downstream data rate in bit/s for Channel 0>
- DSL_DATARATE_DS_BC1=<Downstream data rate in bit/s for Channel 1> *
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Fix when add 'mediatek,cd-poll' to dts cause the sd card be removed randomly.
Special for the device without card-detect pin.
Signed-off-by: Qin Wie <me@vonger.cn>
Use the GPIO dt-bindings macros and add compatible strings in the
ramips device tree source files.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Netgear EX3800 is essentially an EX3700 with a mains output socket.
Both devices use the exact same firmware image (original firmware is named
EX3700-EX3800-version.chk).
This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and
updating the necessary glue.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch cleans up the WN3000RPv3 and EX2700 setup, bringing it in line
with other similar devices:
The power led is a bicolor one. The bootloader brings the red side on at
powerup.
Instead of blinking the red side in diag.sh and need to forcefully turn it off
in 01_leds, this patch simplifies the setup by relying on the default off state
of the gpio-led driver for the red side and blinking the green side as with
other devices.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Cleanup the dtsi files and remove one layer of dtsi. Set the size of
the firmware partition to a value matching the flash size from the
board (variant) name.
Remove the usb led trigger. There is neither a default config for the
usb led trigger nor a LED for usb activity indication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reference the Omnima MiniEMBWiFi device tree source file in the image
build code. Otherwise the dts of the image processed before is used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
So, this is kind of complicated. This has been upstream for a while,
imported from OpenWRT/LEDE with some cleanups. LEDE ramips has stayed
on linux-4.4 this whole time, with the old(er) version of the patch
that had correct behavior[0], while upstream got changed[1].
When LEDE updated to kernel 4.9, the older version of the code from
the patch got replaced with the upstream version containing the bug.
The original behavior, however, seems to be correct here, as the
official programming guide[2] indicates that bit 31 (PDRV_SW_SET)
in register PPLL_CFG1 is reserved, but bit 23 (added as PPLL_LD)
is the PPLL lock state (which also happens to line up with the
error message).
The original confusion probably comes from the double definition
of PDRV_SW_SET[3, 4] in the upstream code, with one correct definition
(31) and one incorrect one (23).
I've also used the opportunity to clean up the error message a bit -
it's still not really helpful to anyone who doesn't already know what
the PPLL is, but at least it's slightly more readable now.
This will probably need to be upstreamed as well, since with the way
it's currently set up, it's unlikely PCI ever worked for anyone who's
running an upstream kernel on that SoC.
[0]: 05d6e92594/target/linux/ramips/patches-4.4/0009-PCI-MIPS-adds-mt7620a-pcie-driver.patch (L259)
[1]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L246)
[2]: http://www.anz.ru/files/mediatek/MT7620_ProgrammingGuide.pdf
[3]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L36)
[4]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L39)
Signed-off-by: Ilya Katsnelson <me@0upti.me>
01_leds had a workaround for the power led to compensate for the
inverted GPIO state. This patch was missing from my previous commit.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[add the power led default-state which was omitted in the last commit
by me]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Luci shows switch ports in wrong order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
All LEDs GPIOs are active low on this device.
WAN and POWER states were inverted. Add default state for power.
Tested on Archer C50v1.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
With d2b6bf1416 ("ramips: fix image validation errors") the board
name was changed to fix an image validation error. But this change
wasn't applied to all other files using the board name, which broke
sysupgrade.
Revert this change and use the former board name in the metadata
instead.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: FS#735
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: FS#735
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix incorrect offset and size of linux partition.
Fixes: 97b36aca09 ("brcm63xx: add pflash for remaining pflash equipped boards")
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The kernel 4.4 patches where already removed with the bump to 4.9. Drop
the the subtarget configs as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.
Specifications:
- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
The square hole is pin 1
The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.
Flash instructions:
You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.
Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.
Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").
Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de>
[remove pinctrl node from dts, no pin is used as GPIO]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Children of the pinctrl0 node are optional. Return EINVAL (=missing)
instead of 0. Fixes a hang if the pinctrl0 has no children.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
there were 2 bugs
*) core1 came up with a bad bogo mips, looks like the clock needed time to stabilize
*) HPT frequency was not set making r4k timers not come up properly
Signed-off-by: John Crispin <john@phrozen.org>
The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 2.5" Drives
- One micro SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: 1 x WAN and 1 x LAN
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Four GPIOs available on a pin header
Flash instructions:
The GnuBee Personal Cloud One ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.
Das U-Boot has multiple options for recovery or updates including :
- USB
- http
- tftp
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use switchdev led trigger, all interfaces are in vlan1; rename leds
according to board.d setting; remove ge2 group from the pinmux, this
group doesn't exist in the driver]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Luci shows switch ports in inverted order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The VoCore2 features 128MB of RAM, therefore set
memory in DTS to 128*1024*1024 = 0x8000000
The board's LED is connected to GND, set it to
ACTIVE_HIGH here.
Make serial console working again on kernel 4.9 by
change of pinmux configuration.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with
a single gigabit ethernet port and two non-detachable antennas, based on
the MT7621A SoC with MT7603E and MT7612E radios.
Firmware wise it is very similar to the QCA based RE450.
SoC: MediaTek MT7621A (880MHz)
Flash: 8MiB (Winbond W25Q64)
RAM: 64MiB (DDR2)
Ethernet: 1x 1Gbit
Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E)
LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act
(green)
Buttons: On/off, LED, reset, WPS
Serial header at J1, 57600 8n1:
Pin 1 TX
Pin 2 RX
Pin 3 GND
Pin 4 3.3V
Factory image can be uploaded directly through the stock UI.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
We will need "mktplinkfw-combined" command also in the "ramips" target
for new MediaTek based TP-Link devices, with "safeloader" image type.
Also, rename the command to "tplink-v1-header", use "VERSION_DIST"
variable instead of "OpenWrt" and allow passing additional parameters.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
We use combined option in "mktplinkfw" tool for generating initramfs
kernel images and header for kernel inside "safeloader" image type (in
fact, only for TL-WR1043ND v4 at this moment).
There is also "mktplinkfw-kernel" tool, a stripped-down version, used
only for generating "simple" header, for safeloader image types.
This changes how "mktplinkfw" handles combined images (which then will
allow us to drop the stripped-down version of the tool):
- drop "ignore size" command line option (it was used only for combined
images anyway)
- don't require "flash layout id" for combined images (we don't need and
shouldn't limit size of the initramfs kernel and for kernels inside
safeloader images, the "tplink-safeloader" tool does the size check)
- require kernel address and entry point in command line parameters for
combined images (consequence of previous point)
- don't include md5 sum and firmware length values in header (they are
needed only for update from vendor GUI and are ingored in case of
initramfs and "tplink-safeloader" images)
- drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed
Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to
match introduced changes in "mktplinkfw" tool.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
On Asus RT-N12 and RT-N16 models, the WAN and LAN4 ports are swapped in the
initial switch configuration since the presets present in nvram appear to be
wrong.
Add special casing for these models to detect_by_model() in order to ensure
a proper switch configuration.
Fixes FS#502.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Power LED of RB912UAG-{2,5}HPnD boards can be controlled by sofware,
so use it for diag purposes and make the User LED free for other tasks.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
It is quite unexpected behaviour when the Power LED switches off as soon
as the kernel starts booting. So set the default state to 'Keep' for
the Power LEDs of all RouterBOARDs (e.g. RB91x, SXT Lite series, etc.).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[switch the default state to keep instead of on]
Signed-off-by: Mathias Kresin <dev@kresin.me>
It uses one MT7615D radio chip with DBDC mode enabled. This mode allows
this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time. However mt76 doesn't support it currently so there is no
wireless available.
Specification:
- SoC: MediaTek MT7621AT
- Flash: 16 MB
- RAM: 128 MB
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Wireless radio: MT7615D on PCIE0
- UART: 1 x UART on PCB - 57600 8N1
Issue:
- Wireless radio doesn't work due to the lack of driver.
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2,then follow the instruction to
set device and tftp server IP address and input the firmware
file name.U-boot will then load the firmware and write it into
the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In the xrx200_close() function we call napi_disable(), that could
sleep, with priv->hw->chan[i].lock held. This could lead to deadlock
and causes the kernel to complain.
Look at the code I couldn't convince myself about why we
need to protect that specific code part with the lock. IMHO there
seems no reason to protect the refcount variables, because AFAIK
ndo_close() and ndo_open() callbacks are already called with a
semaphore held. Neither I could figure out why napi_disable() have to
be called with that lock held. The only remaining code part for
which I could guess the lock is useful for is ltq_dma_close()
function call.
This patch reduces the lock to the said function call, avoiding the
sleep-with-spinlock-held situation
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
[fold into 0025-NET-MIPS-lantiq-adds-xrx200-net.patch, backport to
kernel 4.4]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport upstream commit f44f1e7da7c8e3f4575d5d61c4df978496903fcc ("um:
Avoid longjmp/setjmp symbol clashes with libpthread.a") to fix build
issues on hosts that only have a static libpthread.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Xen serial console has been broken since the xen_domu subtarget
was merged in the generic x86 subtarget (commits 1d6879ee and 371b382a).
The reason for the broken serial console seems to be an IRQ conflict
between the serial console driver and the PATA_LEGACY driver:
[ 1.330125] genirq: Flags mismatch irq 8. 00000000 (hvc_console) vs. 00000000 (platform[pata_legacy.4])
[ 1.330134] hvc_open: request_irq failed with rc -16.
[ 1.330148] Warning: unable to open an initial console.
Just drop the PATA_LEGACY driver from the x86/generic and x86_64
subtargets, since this driver is marked experimental and only supports
very old ISA devices anyway. It is still included in the x86/legacy
subtarget where it rightfully belongs.
Fixes: FS#787
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Xen support for x86/generic was added in 1d6879ee. This commit also
enables it for x86/64.
This was successfully tested with Xen 4.5, although the serial console
is broken in the same way as x86/generic (see FS#787)
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
All x86 subtargets enable USB support, so it makes sense to enable it
in the target config instead, to avoid duplication.
Also refresh subtarget configs accordingly.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This was done by simply running `make kernel_menuconfig CONFIG_TARGET=subtarget`
and then saving without changing any option.
Most of the removed options can be explained because they are already
present in the target config or in the generic 4.9 config:
- PAE-related options, enabled by default on x86 by 961c0eac
- LZO-related options, enabled by default since 4.9
As far as I understand the build system, this shouldn't have any
user-visible impact, because the build system already merges the
various kernel configs during build.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This subtarget was added by 961c0eac, probably by mistake. It does
not contain anything beside a kernel config.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Correct MAC address lookup to appropriate offset based on vendor
source.
Override the WAN MAC to use the same address as LAN. The switch driver
increments the base MAC address for the WAN vlan but the stock firmware
uses the same MAC address for all interfaces.
Based on vendor source commit
https://github.com/domino-team/lede-1701/commit/efb0518
Signed-off-by: John Marrett <johnf@zioncluster.ca>
- Refreshed all patches
- Removed upstreamed
- Adapted 4 patches:
473-fix-marvell-phy-initialization-issues.patch
-----------------------------------------------
Removed hunk 5 which got upstreamed
403-net-phy-avoid-setting-unsupported-EEE-advertisments.patch
404-net-phy-restart-phy-autonegotiation-after-EEE-advert.patch
--------------------------------------------------------------
Adapted these 2 RFC patches, merging the delta's from an upstream commit
(see below) which made it before these 2.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-
stable.git/commit/?h=v4.9.36&id=97ace183074d306942b903a148aebd5d061758f0
180-usb-xhci-add-support-for-performing-fake-doorbell.patch
-----------------------------------------------------------
- Moved fake_doorbell bitmask due to new item
Compile tested on: cns3xxx, imx6
Run tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so
far, so we can just set US unconditionally.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.
The list of binaries is also slightly cleaned up and duplicates are
removed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
RAMFS_COPY_* are moved to platform.sh toplevel. The nand_do_upgrade call is
moved to platform_do_upgrade.
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
RAMFS_COPY_* are moved to platform.sh toplevel. The unneeded
linksys_preupgrade function is removed, and the nand_do_upgrade call is
moved to platform_do_upgrade.
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
TP-Link TL-WR902AC has another one, tiny LED inside RJ45 socket which is
attached to GPIO15. Add support for it, use it as a "lan" LED and rename
old one to "internet". Also, fix uci option name for "lan" LED in system
configuration ("wan" -> "lan").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Until we enable requirement for metadata in sysupgrade images under
ar71xx target, this prevents users from using wrong image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit adds metadata to TP-Link sysupgrade images
created by tplink-safeloader with uImage kernel header.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
With kernel 4.8 common used code was moved to a shared kmod. Add the
missing dependency to the shared snd-soc-simple-card-utils.ko.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There is no device tree property named phynmode0. Use phy-mode as it is
done for the other ethernet nodes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear DM200 is an inexpensive VDSL modem:
CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
RAM: 64MiB
Flash: 8MiB
Ethernet: 1x100M
DSL: VDSL2+, ADSL2+
reset button, 3x bi-color LEDs
Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.
To upgrade from the vendor firmware, upload factory.img
The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.
Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.
Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Most of the ubnt-erx definition can be reused; the package removals in
DEVICE_PACKAGES have become redundant after d17cb4a68a "ramips: purge
default packages on MT7621".
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This change enables .itb image generation for AP148,
It will help us to boot and test AP148 with NOR flash.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The warning will be triggered by jffs2 or UBI, and partial writes are no
issue for most flash chips.
Fixes: 2a2b16210b ("brcm63xx: backport upstream solution for SPI message size limits")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add patches-4.9, some of them (heavily) rewritten:
- ea4500 is upstream available, keep only LEDE changes in dts
- ea3500 is changed to match the structure of the upstream ea4500 dts
- nsa310s rewritten to include the common dtsi
- nsa325 is dropped, since already upstream
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[refresh kernel config, add on100, use the switchdev based mv88e6171
driver for the linksys boards, keep lede specific rootfs/kernel
partition names for linksys boards, reorder patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Netgear UI in basic mode refuses the upgrade file if the the
fileextension is not img. The expert/advanced mode accepts any
fileextension. Use img to make it work in any case.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID for two ommited devices.
Fixes: 7d6c63d ("build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
Root access over serial line in vendor firmware: root/sohoadmin.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
We can use "tplink-fw" mtd splitter for TP-Link devices which use kernel
with TP-Link header embedded inside "safeloader" image type and thus get
rid of statically defined "kernel" and "rootfs" partitions in cmdline.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Refresh mikrotik subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Refresh nand subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Refresh target kernel config and disable kernel support for all boards
which belong to nand and mikrotik subtargets only.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
I tested this on a WRT54GS and a WRT610N V1.
The WRT610N does not boot when the kernel is too big, so I deactivated KALLSYMS
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On the Linksys WRT54GSv1, the Power LED flickers in the "off" state.
Indicate status using the DMZ LED if available, since it has solid "on" and
"off" states.
This change was tested on the WRT54GSv1, but may also affect other brcm47xx
devices.
Fixes FS#793.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
On the Linksys WRT54GSv1, the adm6996 switch driver and the
gpio_button_hotplug module both claim GPIO 6, which is connected to the
Reset button. When the switch driver's request wins, the Reset button
cannot work. This makes it impossible to enter failsafe mode without a
serial console.
Stop requesting the "adm_rc" GPIO in the switch driver, since it is not
used anywhere.
Fixes FS#792.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0
Known issues:
- Unable to detect 53115 switch attached to MDIO. Not supported
- No support for the cable port
More info on the device and the research can be found at:
http://www.actiontec.com/212.html
Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)
Signed-off-by: Anthony Sepa <anthonysepa@yahoo.ca>
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The pinmux register is at relative offset 0x8, not 0xc. Fixes hang
when trying to modify pins >= 32.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Commit 9fec39a (ar71xx: add support for TP-Link TL-WA855RE v1) introduced a
typo in 02_network, fix it by removing the stray paren.
Reported-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin.
As we don't want to break sysupgrade (all existing LEDE release images
for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0.
Fixes FS#852
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)
QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.
Flash instruction:
Use "factory" image directly in vendor GUI.
Recovery method:
1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server.
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset
This commit is based on GitHub PR#1112
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Federico Cappon <dududede371@gmail.com>
Use statically defined sizes for kernel and rootfs mtd partitions.
Vendor upgrade script writes both firmware parts independently which
ends up in a gap between kernel and rootfs images. This results in
incorrectly calculated rootfs_data start offset.
Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL
definition.
Fixes FS#835
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Migrate Arduino Yun from legacy to generic building code.
Note: the mtd partitioning is changed to adopt the LEDE default
partitioning. It allows to have a kernel bigger than 1280k. It is
necessary as kernel > 4.4 with default LEDE configuration grows
bigger.
To use the new partitioning, you need to update your U-Boot env in
advance:
setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
saveenv
Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
This way, the assigned addresses match those on the barcode labels.
Otherwise, the addresses appear to vary on boot.
Signed-off-by: Leon M. George <leon@georgemail.eu>
The kernel configs for all targets should have the version in the
filename, for clearness and consistency across all targets.
It is also expected by the update_kernel.sh script.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
I did not port the regulator and power patches from Stefan Wahren
because I talked to him and he told me that work on this is currently
stalled. And since AFAIK nothing depends on these patches, leaving them
out seems reasonable.
I build minimum default configurations and run-tested them on both
I2SE Duckbill devices and Olimex Olinuxino Maxi boards successfully [1].
[1] Tested:
- debug uart is working
- boot without any obvious kernel problem
- network is coming up and data transfer is possible
- Olinuxino: USB detects a plugged-in pen drive
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
[refreshed config and patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In preparation for bumping mxs target to 4.9, disable a bunch of configuration
symbols that provoked config prompts.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)
Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This patch fixes a problem where the AR8035 PHY can't be
detected on the Cisco Meraki MR24, when the ethernet cable
is not connected during boot.
Russell Senior reported:
|This appears to be a problem during probing of the AR8035
|phy chip. When ethernet has no link, the phy detection fails,
|and eth0 is not created. Plugging ethernet later has no effect,
|because there is no interface as far as the kernel is
|concerned. The relevant part of the boot log looks like this:
|
|[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
(<https://bugs.lede-project.org/index.php?do=details&task_id=687>)
Fixes FS#687
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)
To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add upstream send AR724x PCIe patches to get the PCIe controller out of
reset during driver init.
The AVM Fritz 300E bootloader doesn't take care of releasing the
different PCIe controller related resets which causes an endless hang
as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The driver is used for boards outside the lantiq target as well. Move
it to generic to make it available for more targets.
The phy driver is included in kernel 4.8 as INTEL_XWAY_PHY.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Except for renames and line changes the only conflict was in
allocate_partition in handling MTD_WRITEABLE. Hopefully it was handled
correctly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This mtd_roundup_to_eb helper was introduced years ago in the commit
daec7ad768 ("kernel/3.10: add separate rootfs partition parser") and
it was probably supposed to simplify code a bit.
With the recent upstream commit 1eeef2d7483a7 ("mtd: handle partitioning
on devices with 0 erasesize") the logic in allocate_partition got
slightly more complex and we can't use this simple helper anymore as it
doesn't support MTD_NO_ERASE properly.
There also isn't any real gain from this helper, so it's probably easier
to just don't use it *or* work on upstreaming it to avoid maintenance
cost.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
On boards which don't have a distinct internet and dsl led, use the
shared LED to indicate the xdsl line state and any traffic that is
send/received via the netdev. This traffic doesn't necessarily need to
be internet traffic.
Rename the shared LED of existing configs to "dsl", to match the new
defaults. The configuration of the to be renamed LED is identical with
the new defaults.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Allows to use a single LED for line init status indication and to show
any rx/tx activity on a synchronized dsl line.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.
Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).
Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The Cisco ON100 device is a Kirkwood based router:
SoC: Marvell 88F6282 1600Mhz
SDRAM memory: 512MB DDR3 1333Mhz
Gigabit ethernet: 2x Marvell 88E1310 (over RGMII)
Flash memory: 512MB
2 bi-colour status LEDs (green/red)
1 Reset button
1 USB 2.0 port (on back)
1 SDIO slot (on back)
This commit adds a target profile of "Cisco Systems ON100" under the target
system "Marvell Kirkwood".
Flashing can be performed over tftp, once "dhcp" has been issued:
tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin
nand erase 0x0c0000 ${filesize}
nand write ${loadaddr} 0x0c0000 ${filesize}
Once flashed, set environment variables to boot:
setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs
\; bootm
saveenv
Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
Evaluation boards are left in component form to ease flashing
using vendor tooling and instructions. These boards also do
not include the EOF marker in the UBIFS as the bootloaders
are recent and easily upgradeable.
The end product boards use factory.bin images based on the
dts layout and include EOF markers as bootloader UBI support
is not determined.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
All TP-Link TL-WR710N versions share the same machine code.
This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
