add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49268
CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49234
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.
it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211
Currently the maximum image size defaults to 8Mbyte even though this model has 16Mbyte of flash memory.
Tested and works on my device.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49129
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49104
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.
The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.
Fix the assembly code to reserve stack space for the
registers to avoid that.
Untested. It seems that the lzma-loader is not used at all?
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49062
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
SVN-Revision: 49045
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.
SVN-Revision: 48994
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.
SVN-Revision: 48993
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.
SVN-Revision: 48992
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 48968
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48906
This patch adds support for building factory and sysupgrade images
for the Netgear EX2700 that don't require modification of u-boot
environment variables.
The bootloader on this device expects the kernel partition to end
on a 64k block boundary. The last 64 byte of the kernel partition
must contain a valid uImage header - in the stock firmware, this is
the uImage header of the root filesystem. For this patch, we're using
the uImage header of a 0 byte partition (ex2700-fakeroot.uImage).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48771
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SVN-Revision: 48721
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.
What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48698
The image name for the HiLink HLK-RM04 module has a typo and should read "RM04" rather than "RM02"
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48355
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
Use kernel arch for dts compilation.
Also use Image/BuildDTB to build dts for ramips.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47823
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47617
Add support for Dovado tiny AC wifi router.
Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports
5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47348
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Spaces -> Tabs
2: Removed some packages
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47113
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46629
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46628
The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46624
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
* changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
* changes filenames of dts and profile files
* changes image filenames
for Olimex RT5350F-OLinuXino{,-EVB} devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46623
The following patch changes:
* board name from "wl341v3" to "wl-341v3"
* dts filename
* LED names in dts file
for Sitecom WL-341v3 device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46622
The following patch:
* changes board name from "argus-atp52b" to "atp-52b"
* changes dts filename
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Argus ATP-52B device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46621
This patch removes manufacturer from Belkin F7C027 image name ("belkinf7c027" -> "f7c027").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46620
Other Asus RT-N dts files are named "RT-N..." (not "RTN..."), so use the same for RT-N56U.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46619
The following patch:
* changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
* changes filenames of dts and profile
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Xiaomi MiWiFi Mini device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46617
This patch:
* fixes typo (rp_n53 -> rp-n53) in Asus RP-N53 image name
* removes manufacturer from image names for Lenovo Y1{,S} devices
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46616
There are other Asus boards supported in ramips target, so use the same naming scheme for WL-330N{,3G} boards and their dts files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46615
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46614
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46405
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.
Signed-off-by: Tom Deng <2579131212@qq.com>
SVN-Revision: 46349
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46043
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
SVN-Revision: 46041
Version 2 : White spaces and alphabetical order problems
fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware
Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>
SVN-Revision: 45902
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page
This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.
Signed-off-by: 盛凯 <shengkai81@gmail.com>
SVN-Revision: 45331
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 45208
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
SVN-Revision: 43102
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42892
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
SVN-Revision: 41961
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41939
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 41841
generate sysupgrade image by combine two images.
one is kernel image with seama header.
another is root fs image.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40922
It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40908
Hi Hartmut,
Thanks for your feedback, I have reformated the patch accordingly.
Added support for Teltonika RUT5XX hardware.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
SVN-Revision: 40907
The 7Links PX-4885 is a small battery-powered wireless router.
It is based on a RT5350F WiSoC and features one ethernet port and one
USB port. It is a Hame MPR-A1 clone, except it has different GPIOs,
a different battery and more RAM (32 MB).
This patch adds a profile for this board, the corresponding device tree
file and the adequate base-files changes (incl. sysupgrade).
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
SVN-Revision: 40554
added dts file and userspace scripts modified to support Asus RT-N14U board
current support status:
usb works
ethernet works
buttons reset, wps
leds asus:blue:[usb|lan|wan|air|power]
i2c not tested
uart not tested
wifi not yet
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
SVN-Revision: 39163
The TEW-692GR images are missing since r36169. Uncomment
the board specific macro in image/Makefile, in order to
generate those again.
Only build tested. No idea if the the image works or not,
I have bricked my TEW-692GR a few months ago.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38603
This commit adds the basic elements to support Poray brand routers.
It contains a tool to do the encryption/obfuscation that is used in
Poray routers.
Support for Poray devices was worked on by:
Felix Kaechele <heffer@fedoraproject.org>
Luis Soltero <lsoltero@globalmarinenet.com>
Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37635
r37505 add support for Huawei HG255D, but it only tested under a community hacked u-boot ("lintel u-boot"), which has a different mtd layout compared to origin one. If you install it on a box with origin u-boot, the origin factory part will be destroyed, and your wifi interface will never up!!!
This patch shrink firmware part in mtd layout to exclude origin factory part, and I will prepare another patch to fix the eeprom extract issue for box with origin u-boot.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37530
HG255D is a kind of popular low-end home gateway in China, this patch bring the the trunk support for it. It is adapted from a local Chinese community (www.right.com.cn), so credit should given to them.
This patch is tested to work except trivial LED issues.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37505
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
This patch adds support for HAME MPR-A2 router using a DTS file.
The platform is Ralink RT5350.
http://wiki.openwrt.org/toh/hame/mpr-a2
Signed-off-by: Dmitry Shmygov <shmygov@rambler.ru>
SVN-Revision: 36898
Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c.
With the change to DTS, this is no longer accurate, as ALL5002 is based on
Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding
rt5350.dtsi need to be included for ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3557/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36435
This board uses a TrendChip SOC with its own RAM/Flash for ADSL support.
We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB).
Wiki: http://wiki.openwrt.org/toh/alpha/asl26555
Signed-off-by: Esteban Benito <estebanjbs@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3571/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36433
prepare_generic_squashfs was called twice on the generated images breaking mount_root
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36349
Add Netgear WNCE2001.
This is a small RT3052 device with 4MB spi flash and 32MB ram.
2 built-in antennas, 1x fastE, no USB, reset & wps switch.
On my model the AP/RT switch is unpopulated, but I verified the gpio
mapping for it.
The stock firmware is running an unprotected tftpd which allows you
to read any file from the filesystem.
Serial port is present on testpads (See image on the wiki page).
There are more testpads below the shield near the SoC, which
may have JTAG.
Slight annoyance: The bootloader is checksumming kernel&rootfs, but
can be tricked by zeroing checksum and length fields in the checksum
partition, see
target/linux/ramips/base-files/lib/preinit/04_disable_wnce2001_flash_checksumming
The manufacturer image is very similar to the DAP one, so I slightly
modified mkdapimg to support generating it.
The resulting
openwrt-ramips-rt305x-wnce2001-squashfs-factory-(worldwide|northamerica).bin
can be used to flash from stock to OpenWRT using the stock firmware
upgrade function, without using the serial port.
http://www.netgear.com/landing/wnce2001.aspxhttp://wiki.openwrt.org/toh/netgear/wnce2001
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 36289
Factory image should be used to flash from
original firmware.
[juhosg: use the GENERIC_4M template]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35246
These targets need custom image names specified in the uImage header.
MkImage accepts an optional 4th argument to do exactly that. Reuse the
facility to generate factory images.
Compile-tested, the generated files inspected with "file" utility.
[juhosg:
- keep the factory.bin images to avoid users confusion,
- use GENERIC_4M template for the W306R V2.0
- update commit log]
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35243
This becomes crucial when you are using a generic profile to build an image
larger than 4M, e.g. for w502u.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35238
This patch introduces OpenWRT support for the base Hauppauge/PCTV Broadway
platform. It doesn't deal with the TV tuner or transcoder at this point,
but the core functionality is working (Ethernet, wireless, USB, buttons,
LEDs, etc).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
SVN-Revision: 34595
This should fix the stalled irq problem seen by several people.
This is not the real fix, but rather moves the bug to the un/init patch of the driver.
The real bug still needs to be fixed, but this workaround should be suffcient to make
the ethernet stable.
SVN-Revision: 34177
The new version of the ALL0256N now got 8MB SPI NOR flash instead of 4MB.
In order to expose the whole amount of flash, add another image which contains
the corresponding GENERIC_8M mtdparts.
[juhosg: change suffix from '8m' to '8M']
Patch by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33614
Add support for 8devices Carambola dev board.
The Carambola is a small RT3050-based development board with two
ethernet ports, on-board chip antenna, usb and plenty of accessible
gpio ports, sold by 8devices.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 33303
Generate image for the ALL0239-3G which can be flashed through the
chipset-vendor SDK based firmware's web-interface and bootloader.
The bootloader seems to ignore uImage checksum errors, but does complain about
them once the 0xDEADC0DE was replaced by an actual JFFS2 page.
I'm working on implementing fixtrx for uImage in the mtd package to solve this.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33206
rt2x00 still needs some patching as the radio doesn't come to life.
Installation via webflash.
[juhosg: fix whitespace issues, remove rt305x_register_usb
from machine setup because the board has no USB port]
Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi>
SVN-Revision: 33205
D-Link's DIR-620 allows to flash a uImage directly from its web-interface but
for that the image name should be set to DIR_620.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 33143
Full functionality runtime tested, installation via OEM web-interface requires
a follow-up patch.
Thanks go to Sergey Vasilyugin for his patch that pointed me at the missing
bits (including the antiparallel wps led).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 33142
The initial support for the D-Link DAP-1350.
USB related functionality is not tested.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32821
This patch adds support for the Korean made Petatel PSR-680W Wireless CDMA Router.
The platform is based on Ralink RT3052.
http://wiki.openwrt.org/toh/petatel/psr-680w
Signed-off-by: Dmitry Shmygov <shmygov at rambler.ru>
SVN-Revision: 32450
Fixed: GPIO typos and confirmed GPIO_BUTTON_RESET
Fixed: Lan & Wan reversed: swaped "eth0.2" with "eth0.1" by
removing a line(default is correct), and reversed the
Lan/wan layout LLLLW to WLLLL.
Added: image/Makefile now builds -factory.bin files. I am
unsure of the accepted way to change the makefile but
the name of the image needs to be 'linkn Kernel Image'
in order to be accepted by the OEM firmware.
Known issue: eth0 (internal switch i think has mac address:
00:11:22:33:44:55 but i think it should be same as
the lan).
Known issue: Pressing the reset button has no noticable effect,
i would expect the router to boot failsafe if being
pressed on boot, reboot if short press and reset all
to default if long press.
[juhosg: remove mtdlayout_W306R and use mtdlayout_4M instead]
Signed-off-by: David Pearce <david_18051985@hotmail.com>
SVN-Revision: 31557
Make serial console for DIR-300-B1 work again.
With some recent change, "console=ttyS1,57600" was removed from the
default kernel command line, this adds the necessary mkcmdline
incantation to image/Makefile to add it there for this target.
This is quite likely broken for other targets as well.
Without this the console switches to ttyS0 instead of ttyS1 and
kernel output is missing, and the userspace comes up with 9600 baud
instead of 57600.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 31556
This patch adds support for the ASUS WL-330N3G
Comparing to the WL-330N, It have 32MB ram, usb support and a bicolor led.
The bi-color led is driven by 2 gpio.
I don't know how to handle this, so I simply made 2 leds : one red, one blue.
But the red light takes precedence over the blue one according to the chart below.
r = led is red
b = led is blue
0 = led is off
xy= x->r for red, b for blue led, y->value of brightness in /sys/class/leds/x/brughtness
initial state action led gpio state
r0 b0 r0->r1 r r0 b0
r0 b0 b0->b1 b r0 b1
r1 b0 r1->r0 0 r0 b0
r1 b0 b0->b1 r r1 *b1*
r1 b1 r1->r0 b r0 b1
r1 b1 b1->b0 r r1 b0
r0 b1 r0->r1 r r1 *b1*
r0 b1 b1->b0 0 r0 r0
Signed-off-by: Frédéric Leroy <fredo@starox.org>
SVN-Revision: 31450
More device info at: http://wiki.openwrt.org/toh/tenda/w306r
Signed-off-by: David Pearce <David_18051985@hotmail.com.au>
[juhosg: fix checkpatch errors, remove kmod-phy and luci-ssl packages
from the profile, change broken GPIO number]
SVN-Revision: 31396
[juhosg: fix indentation in platform scripts, and remove debug
messages from 06_set_iface_mac]
Signed-off-by: Patrick van Staveren <trick@vanstaveren.us>
SVN-Revision: 30808
This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19.
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 30434
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
SVN-Revision: 29533
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
SVN-Revision: 28571
This patch adds initial board support for the MoFi Network MOFI3500-3GN
(Ralink RT3052F SoC, 8MB flash, 32MB ram, wireless N, USB-OTG). This
router is basically the NA version of the HW550-3G.
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26466
This patch adds initial support for the Aztech HW550-3G (Ralink
RT3052f SoC, 8MB flash, 32MB dram). Ethernet is not working yet.
Wireless appears to work fine. USB does not work yet (as with other
Ralink boards).
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26123
The attached patch adds a preliminary support for Prolink PWH2004 board
(Ralink RT305x based). LAN and flash appear to work. However, the USB
port and WLAN I have not managed to activate properly yet, but that
problem appears to be present with other rt305x targets as well(?).
Signed-off-by: Esa Hyytia <esa at netlab.tkk.fi>
SVN-Revision: 23129
This patch adds support for Sparklan WCR-150GN board.
Network configuration should be tweaked to make it work fully. The
reason it's not in this patch is that ramips target should be modified
to support different /etc/config/network files for different boards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 22658
When trying to build images with jffs2 filesystem for ramips platform
there is only one jffs2 image produced instead of two (64k and 128k).
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 22435
