Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.
signed-off-by: ngc@ff.iij4u.or.jp
————
————
SVN-Revision: 44469
the old FE_INT_STATUS register becomes two registers.
FE_INT_STATUS and INT_STATUS. so the hw status almost full
must change to read from FE_INT_STATUS register.
tx/rx done read from INT_STATUS register.
mt7620 datasheet define CNT_GDM1_AF at BIT(29).
but after test it should be BIT(13). why?
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44371
MLW221 dts use tabs NOT spaces.
MLWG2 dts typo and 1 tab not spaces
01_leds and diag.sh cleanup
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 44356
This patch sets the correct location of the mt76 radio in the pcie bridge
(pcie-bridge instead of pcie0). Additionaly, it disables the 2.4 GHz band.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44355
Both Y1 and Y1S have MT7612E wireless chip so I submitted this patch.
Tested on Lenovo Y1.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 44354
The ubootloader of the M2M sets the reset bits for
both USB device and USB host during initialization
(to save a few mA of power during boot).
However, for the usb<->sata bridge to be properly
detected, it is necessary to clear both reset bits
as otherwise the kernel logs will just be filled
with:
usb 1-1: device descriptor read/64, error -145
...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44248
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
- budget is decremented with completed frames, so don't check if done is
smaller
- ACK the interrupt before processing further frames to fix a small race
condition.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44234
The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff.
This patch is purpose to fix this issue.
Signed-off-by: wengbj <linux.c@foxmail.com>
SVN-Revision: 44166
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
on mt7621 don't have tx vlan vid registers.
so set FE_REG_FE_DMA_VID_BASE to 0.
set rx vlan offload register to disable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44117
the rx_buf_size now is 1534 when mtu is 1500.
the ethernet frame with vlan tag and FCS is 1522.
so the buffer is enough.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44116
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".
It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.
Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44072
* use default timeout value
* print more debug ring info
* move timeout reset function to workqueue
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44043
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
This patch fixes a wrong mask operation for the rt2880-compatible ralink devices.
The mask operation reads the actual flags and then logical combines it with the pin flag it want to set.
Unfortunally, for rising as for falling interrupt flags the actual flag status of the rising interrupts was used.
That caused a problem if you want to use more than one falling GPIO interrupt.
Now the correct (seperated) actual status is used for both, falling and rising.
Signed-off-by: Jonas Arndt <info@greenwire-elektronik.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43882
modules build during the kernel compile phase are ignored anyway,
all modules should be built using KernelPackage in
package/kernel/linux/modules/*
selecting the appropriate config symbols there rather than in
target/linux/*/config-*
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43842
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43305
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43303
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43301
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43292
the SDK does a bit of extra init that we did not do yet when using an external mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43245
* read MAC address from factory partition
* remove port defines since there is only one port (most likely C/P error)
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 43231
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43201
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
some bootloaders (linksys e1700) set wonky hw trap values. reset this upon boot to make all ports work.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43117
Change list:
* add tx scatter gather function.
* add software rx vlan offload to let GRO work.
* add jumbo frame support. because use build_skb so max MTU is 3812.
* enable hardware tx vlan.
* enable GRO and remove LRO. because it can improve performance and can work on forwarding.
* enable/fix tx padding function.
* let napi handle tx clean up.
* support ethtool operation. now support message level, hardware status and coalesce.
* ethtool support use mdio to get phy status only on mt7620. need modify dts file and add phy info to support it.
Notes:
* build and test on rt2880, rt3052, rt3352, rt3662, rt5350 and mt7620a.
* TCP NAT performance improve. test with netperf.
- rt2880(gigabit) from 5x to 12x Mbps.
- rt3x5x from 6x to 94 Mbps.
- rt5250 from 5x to 8x Mbps.
- rt3662(gigabit) from 6x to 42x Mbps with GRO. 23x Mbps without GRO. 66x Mbps with jumbo frame.
- mt7620 still 94Mbps.
* TSO function not tested. because i don't have mt7620 with eco >= 5. and the hardware don't support to set MSS. it will have problem.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43108
0x8100000c vs 0x810000c0 int he pvc register this caused the cascade with an external mt7530 to fail.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43104
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
SVN-Revision: 43102
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43047
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42892
the driver did not handle all states correctly causing a deadlock of the i2c hw block.
Signed-off-by: Ing.Michele Mogioni <michele.mogioni@unimc.it>
SVN-Revision: 42807
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
the old dwc_otg driver is starting to fall apart and fails on newer 3g
modems and some storage devices. switch to the upstream dwc2 driver which
is no longer in staging/.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42446
This is based on Jon Smirl's patch with the following changes:
- Set CS polarity as low by default.
- Add support for changing CS polarity.
- Add support for changing LSB/MSB.
- Add support for changing SPI mode.
- Fix indentations.
I tested it on a VoCore. Works fine connected to a second flash, but fails to detect MMC/SD cards due to SPI clock speed.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42276
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42194
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42179
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.
Tested on hardware.
[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42178
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
SVN-Revision: 41961
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41939
This patch adds support for setting SPI_CS1 as Chip Select, Watchdog reset output and GPIO#27.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41938
Fix a typo: gpio 21 is already used for the WPS led. Gpio 20 is the
right one (tested) for the mode switch. Confirmed that
/sys/kernel/debug/gpio state followed the position of the switch.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41858
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 41841
Compile tested all subtargets and profiles.
Unfortunately I don't own any board affected by these changes, so no run tests.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41839
The earlier r41797 change was missing this part, to enable the right
vlan configuration.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41838
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken. This seems to fix it.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41837
ASL-26555 16MB: caldata is present on uboot-env and devdata, but the proper one seems to be the devdata, since mac address corresponds to Amper, the real manufacturer, meanwhile the caldata on uboot-env corresponds to D-Link.
ASL-26555 8MB: caldata is only present on uboot-env, but its mac address corresponds to Alpha, the real manufacturer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41768
Move eeprom extraction from scripts to dts files.
Additionally there are few other changes like:
- whitespace fixes
- add partition labels where needed
- BR6524N board doesn't exist (lost in translation?)
- fix Edimax 3g-6200nl model
- add wmac eeprom to dts for Asus RT-N14U board
Compile tested all subtargets and their profiles.
Run tested on:
- Asus RT-N15
- Asus RT-N14U
- Buffalo WHR-600D
- Argus ATP52B
- Sparklan WCR-150GN
Few problems noted:
- many boards didn't have wmac eeprom information defined at all
- several boards don't have any patitions defined (see FIXME comments in dts)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41680
The default case of ramips_setup_macs() is useful when mtd-mac-address is defined in dts.
But lan_mac is not set by default, this results in lan and wan having the same mac.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41632
After r41444 wifi working on WRTnode. Tested.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41452
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
- Support set VLAN ID of each vlan.
- Support untag feature.
- Replace register address with C MACRO.
- There are 8 ports for MT7530 actually.
Signed-off-by: Xiongfei Guo <xfguo@credosemi.com>
SVN-Revision: 41331
move both asus boards to asus.mk
rename HW5503G profile to HW550-3G to match name in image/Makefile
(fixes#16599)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41271
Without this, the ports all end up on vlan 1. This enables a separate
WAN port that works.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41216
In a recent revision (r41177) John Crispin removed the profile for the
AsiaRF AWM002 eval board while adding another AsiaRF board. This
patch restores AWM002 and also corrects a misspelling and an
apparently errant reference to an Allnet ALL0239-3G device.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41215
generate sysupgrade image by combine two images.
one is kernel image with seama header.
another is root fs image.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40922
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
The first switch case is default case. Then it will only
match default case. cause not update the lan/wan mac address.
And in the default switch case the param lan_mac is empty.
it will case error message 'arithmetic syntax error' when
call macaddr_add function.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40910
It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40908
Hi Hartmut,
Thanks for your feedback, I have reformated the patch accordingly.
Added support for Teltonika RUT5XX hardware.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
SVN-Revision: 40907
This patch adds "Asus RT-N10+" as a target option in menuconfig. The device has been supported for a while but is currently missing a profile (.mk).
Signed-off-by: Randolph Kuntz <8D961920@galaxymail.org>
SVN-Revision: 40903
The 7Links PX-4885 is a small battery-powered wireless router.
It is based on a RT5350F WiSoC and features one ethernet port and one
USB port. It is a Hame MPR-A1 clone, except it has different GPIOs,
a different battery and more RAM (32 MB).
This patch adds a profile for this board, the corresponding device tree
file and the adequate base-files changes (incl. sysupgrade).
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
SVN-Revision: 40554
Forgotten patch to fix ethernet for rt2880.
Based on previously submitted patch from Claudio.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 40504
The rt2x00 wifi driver may still need updating to
function with this device.
Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>
SVN-Revision: 39298
