Use devicetree's /chosen/stdout-path instead of the kernel command line
(embedded in the .dts-files) to specify the serial console. Using the
chosen node is recommended on devicetree based platforms.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.
YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.
Common specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm
SR3200 specification:
- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB
XD3200 specification:
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB
LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.
Flash instruction under vendor firmware, using telnet/SSH:
1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
This attribute is not evaluated any more and the boot loader on these
reference boards does not provide a broken root= or console= parameter.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add an extra function to patch the mac and fixup the checksum
afterwards. Calculate the checksum position automatically. The offset
to the mac address is the same for all checksum protected EEPROMs.
No EEPROM requires a byte swapped mac address. The mac byte swap code
was required due to an bug in the script that is now fixed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).
The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)
Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Rob suggested I should use of_machine_is_compatible insteak of a new
property and updated patch has been sent.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is helpful for Orion-based NAS boxes that have the XOR engine enabled
since it provides faster software RAID.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The harddisk target is for NAS boxes, so set the DEVICE_TYPE accordingly so we
get a sensible default package selection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable support for this machine in the kernel and also produce valid image
files with the correct machine id.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW,
because ar71xx is not converted to device tree yet.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.
REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.
Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.
Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
sysupgrade command fails due to missing U-Boot environment-processing
binaries on sysupgrade ramdisk. The missing binaries result in the
following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
The name from the Device define will be used in the metadata. Due to
typo/different spelling, this name might not match the one exported in
/lib/mvebu.sh.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr
Signed-off-by: Andrew Yong <me@ndoo.sg>
Imported from https://source.codeaurora.org/quic/qsdk/system/openwrt/commit/?h=korg/linux-3.4.y/release/arugula_bb_cs&id=2be4f8a8b205ae1a37db44839864451ebe893e6e
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Enable flow control of LAN and WAN ports to
get better performance.
Setup pvid as 0 for all ports during initialisation
to avoid confusion during system or switch INIT.
Disable PORT MAC before config MAC to avoid it work abnormal.
This change is for IR-054144, IR-057315.
Change-Id: I345f3dffa59ad3f97150e09692723da12a7b1067
Signed-off-by: Zou Shunxiang <shunxian@codeaurora.org>
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Imported from e1aaf7ec00%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: net: ar8216: address security vulnerabilities in swconfig & ar8216
This patch does the following changes:
*address the security vulnerabilities in both swconfig framework and in
ar8216 driver (many bound check additions, and turned swconfig structure
signed element into unsigned when applicable)
*address a couple of whitespaces and indendation issues
BUG=chrome-os-partner:33096
TEST=none
Change-Id: I94ea78fcce8c1932cc584d1508c6e3b5dfb93ce9
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/236490
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Commit-Queue: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from fd7b89dd46%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: prevent device duplication in ar8xxx_dev_list
If probe is called twice, once for PHY0 and a second time for PHY4,
the same switch device will be added twice to ar8xxx_dev_list, while
supposedly this list should have one element per hardware switch present
in the system.
While no negative impact have been observed, it does happen if a
platform instanciates these two PHYs from device-tree, as an example.
Change-Id: Iddcbdf7d4adacb0af01975b73f8e56b4582e894e
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/234790
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from c3fd96a7b8%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: hold ar8xxx_dev_list_lock during use_count--
It is possible for the remove() callback to run twice in parallel, which
could result into --use_count returning only 1 in both cases and the
rest of the unregistration path to never be reached.
This case has never been observed in practice, but we will fix
preventively to make the code more robust.
BUG=chrome-os-partner:33096
TEST=none
Change-Id: If09abe27fdb2037f514f8674418bafaab3cbdef6
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/232870
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from c05af20272
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: sync mib_work cancellation
ar8xxx_mib_stop() is called from ar8xxx_phy_remove(), so we want to make
sure the work doesn't run after priv is freed / the device ceases to
exist.
BUG=chrome-os-partner:33096
TEST=none
Change-Id: Iafb44ce93a87433adc4576e5fea5fda58d1f43a9
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/232827
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
RPM clock controller driver had made its way upstream and previous
approach of directly redoing a driver to support ipq806x is a no go anymore.
Thus reverting mentioned patches to upstream state and renaming
in correct patch numbering accordance.
To make the driver work on ipq806x boards we introduce a custom patch.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The SDK Makefile still trys to copy the docs folder which was removed
with 882f4d2d63. This causes an SDK build
error.
All other removals are just cleanup.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Refresh patches on all 4.4 supported platforms.
077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.
Compile & run tested: ar71xx - Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ifxhcd never had roothub support but since kernel 3.x it was expected
that a roothub always exists.
The patched fixed a null pointer deref in the usb subsystem because of
the missing roothub.
Since ifxhcd is gone, this whole patch isn't required any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This way the on nand bad block table is preserved and used. Add support
for nand OOB ECC checksums as well. It should fix all reported ubi
errors, which were all related to bad nand blocks and a purged on nand
bad block table.
The existing ubi partition will be reused, which eliminates the need
to touch the caldata during initial install. The BT u-boot has support
for loading a kernel from an ubi volume. It isn't necessary any longer
to replace the BT u-boot with a custom compiled one to use LEDE.
It is required to restore the BT Firmware and install LEDE from scratch
to switch to the new partition layout.
An image for restoring the BT firmware and installing LEDE is provided
at https://github.com/mkresin/lede/releases.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport upstream commit a61ae81a1907af1987ad4c77300508327bc48b23.
The actually purpose of the patch was to do some cleanup. As a side
effect of this cleanup, the device node is now passed to nand_dt_init.
This allows to use the common nand device tree properties
- nand-bus-width
- nand-on-flash-bbt
- nand-ecc-mode
- nand-ecc-step-size
- nand-ecc-strength
for the plat_nand driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the addition of the bindings to the ath9k driver, this code
isn't used any longer. The fixup is now done by the owloader.
Rename the ath_eep.c file to ath5k_eep.c to indicate that this files
includes ath5k related code only.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.
The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.
Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This adds support for the Intel Falcon SoC for GPON.
Support for the Falcon SoC was removed in commit c821836395 svn rev:
40392 from OpenWrt, this commit adds it again.
This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DEVICE_PACKAGES are not included in the initramfs image in case
TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images
with a not working network configuration because of a missing swconfig.
Workaround the issues by adding the essential swconfig package to the
default packages selection and deselect swconfig for boards not having
swconfig included before via device packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.
Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.
Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.
If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.
Use the usb pinmux settings from the nbg6817 gpl sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).
This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.
Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.
Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.
Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.
Change gpioexport to gpio pinmux.
Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.
Remove pcie pinmux from D7800.
Move pinctrl to correct place in NBG6817 and R7800.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This allows specifying PCI devices as children of the PCIe controller
node to pass configuration data to them.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fix bug that LEDE failed to boot with this message:
WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214
mt7621_spi_transfer_one_message+0x28c/0x620()
Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000).
Signed-off-by: Andrew Yong <me@ndoo.sg>
This device uses NAND FLASH, so it should be kept in nand subtarget.
Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
CONFIG_CRYPTO_DEV_SUN4I_SS was previously set to y but did not take
effect because of the absence of CONFIG_CRYPTO_HW=y
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Currently, the device-tree partition is marked as read-only.
Hence, userspace tools like mtd can't write into the partition.
This however will be necessary in case the DTB needs to be
updated.
This patch also adds the kernel.dtb image, so the compiled
DTB is exported as a file and available in the binary
directory along the firmware images.
Note: the u-boot does expects the dtb to be a uimage.
To update the dtb manually:
1. copy the generated dtb to the router.
2. mtd erase /dev/mtd2
3. mtd write wndr4700.dtb /dev/mtd2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Unlike x86, kvm for arm has to be built into the kernel. The kernel
config was prepared with the following command
make kernel_menuconfig CONFIG_TARGET=platform
Then enable ARM_LPAE, VIRTUALIZATION, KVM in that order
Other config changes are done by the build system. The following text
tries to explain some of them, for archive purposes probably...
- BUILD_BIN2C. It was dropped probably because the prompt is empty and
no other config option selects it. bin2c is a host executable for
converting binary content to a piece of c code for inclusion
- CRYPTO_DEV_SUN4I_SS. It was dropped because the dependency CRYPTO_HW
was not enabled. Setting that aside, packaging it as a loadbable
module in lieu of other sunxi specific modules seems more appropriate
- PGTABLE_LEVELS. It was changed from 2 to 3 because 3 is the default
when ARM_LPAE is enabled
- HAVE_KERNEL_GZIP, etc.. These are enabled in generic config
- SCHED_INFO, ZLIB_INFLATE. These were dropped probably for the same
reason as for BUILD_BIN2C
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.
The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.
Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).
For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci
in mt7621.dtsi and enable the nodes in the indiviual board dts files.
The nodes require further device specific configuration anyway.
Remove the m25p80@0 spi child node from mt7621.dtsi and add the
chunked-io parameter to the individual board dts files. Fix the spi
flash compatible string for the WNDR3700V5.
Drop the mt7621-eval-board compatible string for all boards which are
not the eval board.
Drop the linux,modalias parameter from spi flash node.
Remove the xhci node from board files, it is already enabled in dtsi.
Disable xhci for boards not having usb ports populated.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix configuration files for the Livebox 1 routers.
- Add status led
- Set eth0 as the LAN port, for coherence with RedBoot and comfortability.
- Add led triggers
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix Image generation for the Livebox 1
- missing "relocate-kernel", wrong "LOADADDR", fix it
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- part probe wrong, it should be RedBoot (uppercase matters)
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- leds are totally wrong, fix them.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- no failsafe button, use button 1 for this purpose
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)
Signed-off-by: Andrew Yong <me@ndoo.sg>
Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This adds the patch submitted to upstream that adds BQL to the mvneta
driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under
load when the physical link is saturated.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Parameters for dwc2 on lantiq.
A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Device tree binding for dwc2 usb driver on danube.
Leave old ifxhcd-danube driver as an alternative.
Also adds dr_mode = "host" to eliminate warning on boot.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60
Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port
More info can be found at https://wiki.openwrt.org/toh/meraki/mx60
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Update patch to remove pipetypes var declaration which was throwing
unused variable warning due to the original patch removing the only use.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw.
Add *page* in the argument list and remove the local variable.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This fixes parsing partition placed after TRX with block-aligned length.
It's important e.g. for Archer C9 which has TRX with kernel only and
rootfs as separated partition.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix build on targets not using CONFIG_MODULE_STRIPPED.
Neither RTL8367_DRIVER_DESC nor RTL8367B_DRIVER_DESC are defined
anywhere. It worked for targets using CONFIG_MODULE_STRIPPED since our
module stripper no-ops the various module info macros.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Change grub's root device to xen/xvda,msdos1 for the x86_xen_domu
target so that it will boot without further changes.
Signed-off-by: Wilfried Klaebe <w+lede-project@chaos.in-kiel.de>
[Jo-Philipp Wich: fixed and rebased patch from FS#264, added subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch refreshes the ipq806x kernel patches.
There was a large PR for ipq806x in the queue when the kernel patches
were refreshed for 4.4.32, so currently there is quite much fuzz for
ipq806x.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a powerful API for parallel crypto from which many other modules
can benefit. It only winds up being turned on on SMP systems, which
means this adds 0 bytes to the kernel on tiny machines, while only
adding a small bit to SMP systems for big performance improvements.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Adds Google's mirror as primary source and kernel.org as fallback.
Same as commit 0d4f02dfd6
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
In Device/ls1012ardb IMAGES variable, there are two separate firmware
references to the same packages, while do mult-job compile, the same package
build process will arise conflict occasionally. So, only reserve one ext4 fs
as the default firmware.bin.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
OpenMesh devices have often LEDs which are not yet used by OpenWrt. These
should still be available as disabled LEDs in the system configuration for
easier modification.
Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com>
[sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh,
add wifi/status LEDs]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
MMC support has been added to x86-64 a while ago, there is no reason not
to support it in x86-generic as well.
Signed-off-by: Andreas Ziegler <github@andreas-ziegler.de>
[Matthias Schiffer: add commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
PATA support has been removed from x86-generic without any note in LEDE
r538. Not including them makes the generated images incompatible with older
(and some newer) hardware without any significant gain.
Add it back, and also add the same drivers (as far as available) to x86-64.
Signed-off-by: Andreas Ziegler <github@andreas-ziegler.de>
[Matthias Schiffer: add back x86-generic, update commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.
Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Without setting the HSR to the selected channel, the WLAN of the UAP
Outdoor+ will exhibit high packet loss in RX.
Based-on-patch-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The marvell,88e6352 and marvell,88e6172 compatible strings are used in
target/linux/generic/files/drivers/net/phy/mvsw61xx.c. No idea why grep
missed them when I searched for them.
Thanks to Syrone Wong for noticing and reporting my mistake.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All compiled device tree files not mentioned are binary identical to the
former ones.
Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts.
Due to the include of the input binding header, the BTN_* node names in:
- ramips/GL-MT300A.dts
- ramips/GL-MT300N.dts
- ramips/GL-MT750.dts
- ramips/Timecloud.dts
will be changed by the compiler to the numerical equivalent.
Move the binding include of lantiq boards to the file where they are
used the first time to hint the user where the values do come from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes invalid device tree parameters.
Drop the mvsw61xx node used in mvebu device tree source files. It looks
like some kind of ethernet switch cargo cult. Neither the
marvell,88e6352 nor the marvell,88e6172 compatible strings can be found
in any LEDE file or in the kernel sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This special dwc2 device definition for the Netgear WNDR4700
has been replaced by amcc,usb-otg-405ex.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch moves the common SoC device tree entries
from the currently four supported platforms into a
common apm82181.dtsi.
Furthermore, this patch also changes the GPIO, IRQ and
input definitions of the supported platforms to use the
defined dt-bindings macros for GPIO_ACTIVE_LOW|HIGH,
KEY_WPS|RESTART|*, IRQ_TYPE_* when it's appropriate.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the amcc,usb-otg-405ex device
which is found in all APM82181 SoCs.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
As specified by e0229a16b0 if the VR9
based router provides FXS ports and they should enabled then the
following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M
By adding mem= parameter a pci device stop working correctly. The
pci-lantiq.c module use get_num_physpages() to compute dynamically the
memory amount of the board.
The mem= make the module to compute in the wrong way the BAR11MASK, so
in this situation the mask is misaligned with the dma area that the
hardware expects.
This patch is a port of what legacy ifxmips_pci.c does.
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
The latest stock firmwares for US and EU regions have started checking the
region code.
Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some builders have troubles cloning the boot-wrapper-aarch64.git repository so
provide a mirror checksum to allow downloading from sources.lede-project.org
instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.
The MAC address numbering of the TEW-691GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:0C
WIFI: AA:BB:CC:DD:EE:0D
WAN: AA:BB:CC:DD:EE:0F
The MAC address numbering of the TEW-692GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:e4
WAN: AA:BB:CC:DD:EE:e5
2.4GHz: AA:BB:CC:DD:EE:e7
5 GHz: AA:BB:CC:DD:EE:e8
Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.
Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.
Set the label and compatible string according to the the PCI binding
documentation.
Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.
Use the usual eeprom for the soc wmac of the Dovado Tiny AC.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set a device specific wireless mac address for ARV7506PW11, VGV7519 and
VGV7510KW22. The one from the EEPROM is a generic one and the same on
all boards.
Use the wifi@0,0 label and the pci0,0 compatible string for the
ARV7519PW and ARV7525PW since the pci vendor and device id is unknown.
It should work anyway since the compatible string isn't evaluated
(yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It's supposed to significantly improve performance but doesn't seem to
affect Northstar unfortunately. It seems only some other platforms were
limited because of this DMA setup mistake.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The original repo in this Makefile disappeared from the internet so use another
copy of this repository on kernel.org. Also switch from git:// to https://
while being at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Port 1 registers the same IO resources as port 2 in the kernel resource
tree, which is wrong.
Fix this by using it's own resources as indicated in the overview
(cns3xxx.h).
Compiled & Tested on several GW2388-4 laguna boards which utilizes all 3
ports.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Since commit 484cb91 "sdk: bundle required firmware files" there is an
implicit dependency of the SDK on a prior Kernel compilation.
Change target/Makefile to make this dependency explicit to avoid race
conditions with parallel builds.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Switch to xz compression instead of using bz2.
This makes a considerable difference in size, ar71xx SDK from 60M to 35M.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
- remove not existing properties
- remove properties having the same values as the included dtsi
- remove nodes which are disabled in the included dtsi and not enabled
in dts
- replace the deprecated pinctrl-* compatible strings
- use the same labels for nodes as the included dtsi
- move common used vr9 pci properties to vr9.dtsi
- remove the unused stp node from HomeHub 2B devcie tree source file
- fix spaces vs. tabs and remove superfluous linebreaks
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver
Also switching to ondemand frequency scaling as it is fixed now
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.
Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)
Modified after cherry-pick:
obj in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756
If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1
To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)
Modified after cherry-pick:
compatible attribute
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on ar71xx, brcm47xx, kirkwood.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
Thanks to leaving .pattern file we can easily insert extra step between
linksys-pattern-partition and trx-v2-with-loader, e.g. rootfs one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
