ipq806x: add support for TP-Link Archer VR2600v
This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
This commit is contained in:
parent
0e7869f204
commit
ae79c41286
8 changed files with 467 additions and 2 deletions
|
@ -45,6 +45,13 @@ nbg6817)
|
|||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5" "phy0radio"
|
||||
ucidef_set_led_netdev "wan" "WAN" "$board:white:internet" "eth1"
|
||||
;;
|
||||
vr2600v)
|
||||
ucidef_set_led_usbport "usb" "USB" "${board}:white:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1"
|
||||
ucidef_set_led_switch "lan" "lan" "${board}:white:lan" "switch0" "0x1e"
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${board}:white:wlan2g" "phy0radio"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${board}:white:wlan5g" "phy1radio"
|
||||
ucidef_set_led_switch "wan" "wan" "${board}:white:wan" "switch0" "0x20"
|
||||
;;
|
||||
*)
|
||||
;;
|
||||
esac
|
||||
|
|
|
@ -18,7 +18,8 @@ c2600 |\
|
|||
d7800 |\
|
||||
r7500 |\
|
||||
r7500v2 |\
|
||||
r7800)
|
||||
r7800 |\
|
||||
vr2600v)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
|
||||
;;
|
||||
|
|
|
@ -63,6 +63,9 @@ case "$FIRMWARE" in
|
|||
r7800)
|
||||
ath10kcal_extract "art" 4096 12064
|
||||
;;
|
||||
vr2600v)
|
||||
ath10kcal_extract "ART" 4096 12064
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath10k/cal-pci-0001:01:00.0.bin")
|
||||
|
@ -82,6 +85,9 @@ case "$FIRMWARE" in
|
|||
r7800)
|
||||
ath10kcal_extract "art" 20480 12064
|
||||
;;
|
||||
vr2600v)
|
||||
ath10kcal_extract "ART" 20480 12064
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
*)
|
||||
|
|
|
@ -21,6 +21,9 @@ case "$board" in
|
|||
r7800)
|
||||
echo $(macaddr_add $(mtd_get_mac_binary art 6) $(($PHYNBR + 1)) ) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
vr2600v)
|
||||
echo $(macaddr_add $(mtd_get_mac_binary default-mac 0) $(($PHYNBR - 1)) ) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
*)
|
||||
;;
|
||||
esac
|
||||
|
|
|
@ -41,6 +41,9 @@ ipq806x_board_detect() {
|
|||
*"R7800")
|
||||
name="r7800"
|
||||
;;
|
||||
*"VR2600v")
|
||||
name="vr2600v"
|
||||
;;
|
||||
esac
|
||||
|
||||
[ -z "$name" ] && name="unknown"
|
||||
|
|
|
@ -37,6 +37,11 @@ platform_do_upgrade() {
|
|||
ea8500)
|
||||
platform_do_upgrade_linksys "$ARGV"
|
||||
;;
|
||||
vr2600v)
|
||||
PART_NAME="kernel:rootfs"
|
||||
MTD_CONFIG_ARGS="-s 0x200000"
|
||||
default_do_upgrade "$ARGV"
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
|
|
|
@ -0,0 +1,423 @@
|
|||
#include "qcom-ipq8064-v1.0.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "TP-Link Archer VR2600v";
|
||||
compatible = "tplink,vr2600v", "qcom,ipq8064";
|
||||
|
||||
memory@0 {
|
||||
reg = <0x42000000 0x1e000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
rsvd@41200000 {
|
||||
reg = <0x41200000 0x300000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &uart4;
|
||||
mdio-gpio0 = &mdio0;
|
||||
|
||||
led-boot = &power;
|
||||
led-failsafe = &general;
|
||||
led-running = &power;
|
||||
led-upgrade = &general;
|
||||
};
|
||||
|
||||
chosen {
|
||||
linux,stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
soc {
|
||||
pinmux@800000 {
|
||||
led_pins: led_pins {
|
||||
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
|
||||
"gpio26", "gpio53", "gpio56", "gpio66";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
i2c4_pins: i2c4_pinmux {
|
||||
mux {
|
||||
pins = "gpio12", "gpio13";
|
||||
function = "gsbi4";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button_pins {
|
||||
pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19", "gpio21";
|
||||
function = "gsbi5";
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
data {
|
||||
pins = "gpio18", "gpio19";
|
||||
drive-strength = <10>;
|
||||
};
|
||||
|
||||
cs {
|
||||
pins = "gpio20";
|
||||
drive-strength = <10>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
clk {
|
||||
pins = "gpio21";
|
||||
drive-strength = <12>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio0_pins: mdio0_pins {
|
||||
mux {
|
||||
pins = "gpio0", "gpio1";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
rgmii2_pins: rgmii2_pins {
|
||||
mux {
|
||||
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
||||
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
||||
function = "rgmii2";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
gsbi@16300000 {
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
status = "ok";
|
||||
serial@16340000 {
|
||||
status = "ok";
|
||||
};
|
||||
/*
|
||||
* The i2c device on gsbi4 should not be enabled.
|
||||
* On ipq806x designs gsbi4 i2c is meant for exclusive
|
||||
* RPM usage. Turning this on in kernel manifests as
|
||||
* i2c failure for the RPM.
|
||||
*/
|
||||
};
|
||||
|
||||
gsbi5: gsbi@1a200000 {
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
status = "ok";
|
||||
|
||||
spi4: spi@1a280000 {
|
||||
status = "ok";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash: W25Q128@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
|
||||
SBL1@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
MIBIB@20000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x20000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL2@40000 {
|
||||
label = "SBL2";
|
||||
reg = <0x40000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL3@80000 {
|
||||
label = "SBL3";
|
||||
reg = <0x80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
DDRCONFIG@100000 {
|
||||
label = "DDRCONFIG";
|
||||
reg = <0x100000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SSD@110000 {
|
||||
label = "SSD";
|
||||
reg = <0x110000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TZ@120000 {
|
||||
label = "TZ";
|
||||
reg = <0x120000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
RPM@1a0000 {
|
||||
label = "RPM";
|
||||
reg = <0x1a0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBL@220000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x220000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBLENV@2a0000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x2a0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
OLDART@2e0000 {
|
||||
label = "OLDART";
|
||||
reg = <0x2e0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
kernel@320000 {
|
||||
label = "kernel";
|
||||
reg = <0x320000 0x200000>;
|
||||
};
|
||||
|
||||
rootfs@520000 {
|
||||
label = "rootfs";
|
||||
reg = <0x520000 0xa60000>;
|
||||
};
|
||||
|
||||
defaultmac: default-mac@0xfaf100 {
|
||||
label = "default-mac";
|
||||
reg = <0xfaf100 0x00200>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
ART@fc0000 {
|
||||
label = "ART";
|
||||
reg = <0xfc0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
phy@100f8800 { /* USB3 port 1 HS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@100f8830 { /* USB3 port 1 SS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@110f8800 { /* USB3 port 0 HS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@110f8830 { /* USB3 port 0 SS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb30@0 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb30@1 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
pcie0: pci@1b500000 {
|
||||
status = "ok";
|
||||
phy-tx0-term-offset = <7>;
|
||||
};
|
||||
|
||||
pcie1: pci@1b700000 {
|
||||
status = "ok";
|
||||
phy-tx0-term-offset = <7>;
|
||||
};
|
||||
|
||||
mdio0: mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
device_type = "ethernet-phy";
|
||||
reg = <0>;
|
||||
qca,ar8327-initvals = <
|
||||
0x00004 0x7600000 /* PAD0_MODE */
|
||||
0x00008 0x1000000 /* PAD5_MODE */
|
||||
0x0000c 0x80 /* PAD6_MODE */
|
||||
0x000e4 0x6a545 /* MAC_POWER_SEL */
|
||||
0x000e0 0xc74164de /* SGMII_CTRL */
|
||||
0x0007c 0x4e /* PORT0_STATUS */
|
||||
0x00094 0x4e /* PORT6_STATUS */
|
||||
>;
|
||||
};
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
device_type = "ethernet-phy";
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: ethernet@37200000 {
|
||||
status = "ok";
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <1>;
|
||||
|
||||
pinctrl-0 = <&rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
mtd-mac-address = <&defaultmac 0>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
gmac2: ethernet@37400000 {
|
||||
status = "ok";
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
|
||||
mtd-mac-address = <&defaultmac 0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
rpm@108000 {
|
||||
pinctrl-0 = <&i2c4_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
wifi {
|
||||
label = "wifi";
|
||||
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
dect {
|
||||
label = "dect";
|
||||
gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_PHONE>;
|
||||
};
|
||||
|
||||
ledswitch {
|
||||
label = "ledswitch";
|
||||
gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_LIGHTS_TOGGLE>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
dsl {
|
||||
label = "vr2600v:white:dsl";
|
||||
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "vr2600v:white:usb";
|
||||
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "vr2600v:white:lan";
|
||||
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "vr2600v:white:wlan2g";
|
||||
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "vr2600v:white:wlan5g";
|
||||
gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
power: power {
|
||||
label = "vr2600v:white:power";
|
||||
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
phone {
|
||||
label = "vr2600v:white:phone";
|
||||
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "vr2600v:white:wan";
|
||||
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
general: general {
|
||||
label = "vr2600v:white:general";
|
||||
gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "ok";
|
||||
};
|
|
@ -224,6 +224,23 @@ define Device/NBG6817
|
|||
$(call Device/ZyXELImage)
|
||||
endef
|
||||
|
||||
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817
|
||||
define Device/VR2600v
|
||||
PROFILES += $$(DEVICE_NAME)
|
||||
FILESYSTEMS := squashfs
|
||||
KERNEL_SUFFIX := -uImage
|
||||
KERNEL = kernel-bin | append-dtb | uImage none
|
||||
KERNEL_NAME := zImage
|
||||
KERNEL_SIZE := 2097152
|
||||
DEVICE_DTS := qcom-ipq8064-vr2600v
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
BOARD_NAME := vr2600v
|
||||
DEVICE_TITLE := TP-Link Archer VR2600v
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
|
||||
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817 VR2600v
|
||||
|
||||
$(eval $(call BuildImage))
|
||||
|
|
Loading…
Reference in a new issue