Commit graph

20022 commits

Author SHA1 Message Date
Mathias Kresin
a14097e8e0 ramips: fix mt7620a ND/SD pins pinmuxes
Drop the nd_sd gpio pinmux in case sdcard is used. They're mutually
exclusive and for most of the boards not even used as GPIOs.

If the pins are in sdcard mode, the pins ND_WE_N and ND_CS_N are still
GPIOs (#45 and #46).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
2cc7980dcb ramips: reference node by label
Reference the HC5661A sdhci node by label instead of by the full path.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
1d08951628 ramips: add rt3352 SPI_CS1 pinmux
The rt3352 has a pin that can be used as second spi chip select,
watchdog reset or GPIO. The pinmux setup was missing the definition of
said pin but it is already used in the SoC dtsi.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Felix Fietkau
36c6ba3735 imx6: use BUILD_DEVICES in uboot-imx6 for mx6cuboxi
Fixes build with the default profile

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-05 10:00:01 +02:00
Felix Fietkau
b9f926e151 imx6: rename Generic profile to Default, fixes u-boot image build issue
u-boot.mk checks for the Default profile to build images for all targets.
This brings the target default profile in sync with other targets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-05 10:00:01 +02:00
Matthias Schiffer
b452af23a8
mpc85xx: add migration script for TP-Link TL-WDR4900 v1 WLAN PCI paths
PCI paths of the WLAN devices have changed between kernel 4.4 and 4.9;
migrate config so existing wifi-iface definitions don't break.

This is implemented as a hotplug handler rather than a uci-defaults script
as the migration script must run before the 10-wifi-detect hotplug handler.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-09-04 21:27:27 +02:00
Felix Fietkau
ded905ce43 imx6: extend cubox support to hummingboard, add support for building full images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Felix Fietkau
8c41f1f81c imx6: enable f2fs and loopback support in preparation for squashfs with overlay support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Felix Fietkau
00f030a9c6 build: add support for enabling the rootfs/boot partition size option via target feature
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Felix Fietkau
b605a84a74 ramips: ethernet: unify tx descriptor buffer splitting
A buffer is split into multiple descriptors if it exceeds 16 KB.
Apply the same split for the skb head as well (to deal with corner cases
on fraglist support)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Jo-Philipp Wich
4302c917cc Revert "ramips: mmc: Fix init for MT7628AN"
This reverts commit 3a8efaef00.

The change reportedly breaks UART2 on some boards. Furthermore it uses
bitwise logic on an uninitialized variable and fails to explain what it
is fixing exactly.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-30 13:19:26 +02:00
Jo-Philipp Wich
77e2bccde8 ramips: only limit lzma dictionary size on mt7621
The changed dictionary size leads to a different LZMA header which breaks
sysupgrade image magic checkibng on at least some RT288x boards.

Since the commit message only mentions testing on MT7621 and since the
change appears to break at least one other ramips subtarget, do not take
any chances and restrict the size limitation to only MT7621.

Fixes FS#1797
Fixes 09b6755946 ("ramips: limit dictionary size for lzma compression")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-30 10:57:35 +02:00
Mathias Kresin
a6e11ccb13 ramips: fix rt3883 pinmux for second SPI
The rt3883 doesn't have a pinmux group named spi_cs1. The cs1 is part
of the pci group. The function pci-func enables the second chip select.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 21:00:58 +02:00
Mathias Kresin
dcdc6d9dad ramips: fix rt3883 pci pinmux
The PCI pins need to be set to "PCI Host support one device" to allow
the use of one PCI device and flash memory.

The pci-fnc function is intended to be used if no PCI is used but
flash, nand or the codec functionality is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 21:00:58 +02:00
Freddy Leitner
7aa5dc46ee apm821xx: MBL: load kernel/dtb from SATA 0:1 first
This remedies an issue with the MBL Duo if both disks are inserted
and contain OpenWrt. kernel and dtb would be loaded from SATA 1:1
while rootfs (/dev/sda2) would be mounted on SATA 0:1.

Such a mix&match would obviously only work if both OpenWrt versions/
builds are identical, and especially fail after sysupgrade upgraded
the system disk on SATA 0:1.

The fallback to SATA 1:1 needs to be kept for MBL Single (only has
SATA 1:1) and MBL Duo with one disk inserted on SATA 1:1. To speed
up booting in those cases, the unneccesarily doubled "sata init"
will only be called once. (In theory it could be omitted completely
since the on-flash boot script already initializes SATA to load the
on-disk boot script.)

Tested on MBL Duo (all possible combination of disks) and MBL Single

Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Freddy Leitner <hello@square.wf>
2018-08-29 09:43:10 +02:00
Mathias Kresin
c134210b8f ramips: drop pointless default led definitions
The LEDs should be triggered/lit by any kind of state change instead of
turned on/off unconditional.

If LEDs really need to be turned off by default, it should be done via
the default-state devicetree led property.

The handling of the wndr3700v5 and wt3020 power led is at least
strange. Something is for sure wrong with them. Either the leds are
misnamed, the default off trigger is a typo or the polarity of the
gpios is wrong. Drop the power led from userspace and wait for someone
with access to the hardware to fix it properly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:39:32 +02:00
Mathias Kresin
43df31f64d ramips: add missing zbt-cpe102 diag led
Based on the userspace led configuration it's quite obvious that the
4g-0 led should be used for boot status indication.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:34:09 +02:00
Mathias Kresin
99045dfc59 ramips: express diag led handling via devicetree
Use the default-state property to express the desired led handling in
the devicetree source file instead of the userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:34:07 +02:00
Mathias Kresin
111907e8d3 ramips: remove default on userspace trigger for diag leds
All the LEDs are turned on by diag.sh at the end of the boot process.
No need to do the same via userspace configuration again.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:26:24 +02:00
Mathias Kresin
56e6ebdea4 ramips: fix multi colour led handling
All boards either have a multi colour led or a single lightpipe. It
makes it impossible to handle the LEDs individual. Change the LED
config for these boards to take it into account.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:24:49 +02:00
Mathias Kresin
fe1e90deb4 ramips: rt-n12p: use the boardname helper variable
Use the helper variable for the Asus RT-N12P as it is done by all
boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:23:11 +02:00
Koen Vandeputte
01793e8752 kernel: bump 4.14 to 4.14.67
Refreshed all patches.

Removed upstreamed patches:
- 037-v4.18-0008-ARM-dts-BCM5301x-Fix-i2c-controller-interrupt-type.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-28 23:05:39 +02:00
Koen Vandeputte
22f899c6dd kernel: bump 4.9 to 4.9.124
Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-28 23:05:39 +02:00
Koen Vandeputte
23366b6dc6 mediatek: remove duplicate RPS patch
Commit 7af1fb9faa ("kernel: add a RPS balancer") introduces a RPS balancer
for all targets.

In the past however, this patch was already introduced for target "mediatek"
in commit 7762c07c88 ("mediatek: bump to v4.14")

Remove the separate copy of the patch within the mediatek target,
which otherwise is applied twice and results in a build error.

Fixes: 7af1fb9faa ("kernel: add a RPS balancer")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-28 14:57:15 +02:00
John Crispin
fd20fdd0b8 ath79: fix remove irq code from pci driver patch
This patch got mangled in the void while rebasing it.

Signed-off-by: John Crispin <john@phrozen.org>
2018-08-28 11:58:50 +02:00
John Crispin
1d4d156a7c generic: add flow_offload accounting
This patch makes the flow offloading layer account for the traffic inside
the conntack entries.

Signed-off-by: John Crispin <john@phrozen.org>
2018-08-28 11:30:39 +02:00
John Crispin
7af1fb9faa kernel: add a RPS balancer
By default the RPS delegation will happen by masking the last few bits of
skb->hash. This patch adds an inermediate hash bucket that maps the masked
hash to a RPS core. This makes RPS results much more deterministic on SMP
systems.

Signed-off-by: John Crispin <john@phrozen.org>
2018-08-28 11:30:26 +02:00
David Bauer
8e9a59a6b9 build: add mkrasimage
The current make-ras.sh image generation script for the ZyXEL NBG6617
has portability issues with bash. Because of this, factory images are
currently not built correctly by the OpenWRT buildbots.

This commit replaces the make-ras.sh by C-written mkrasimage.

The new mkrasimage is also compatible with other ZyXEL devices using
the ras image-format.
This is not tested with the NBG6616 but it correctly builds the
header for ZyXEL factory image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-28 11:26:53 +02:00
Dmitry Tunin
8132e06247 ath79: fix ar7100 PCI IRQ handling
Currently all PCI devices get the same IRQ that affects performance badly.

This commit adresses this problem and cleans the code.

ar7100 has a special PCI interrupt controller@18060018 that works exactly
the same way as misc interrupt controller.

This patch does the following:

1. Defines pci-intc interrupt controller@18060018 in dtsi.
2. Removes interrupt-controller property from PCI node.
3. Sets a correct interrupt mask for PCI devices.
4. Removes all IRQ handling code from the PCI driver.

"qca,ar7100-misc-intc" should be used as the compatible property, becuase on ar7100
the controlled status register is read-only and the ack method used in
"qca,ar7240-misc-intc" won't work properly.

There are two very minor downsides of this patch that don't affect perormance:

1. We allocate an IRQ domain of 32 IRQ, whan we need only 5. But ar7100 aren't tiny un terms of RAM
and that is not very important and can be tuned if we implement "nr-interrupts" property".

2. It reuses the same irg chip name "MISC" for both controllers.

Run tested on DIR-825 B1.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-28 11:26:53 +02:00
Chuanhong Guo
028daa9974 ath79: ag71xx: apply interface mode to MII0/1_CTRL on ar71xx/ar913x
We currently don't have any code configuring interface mode in ath79,
meaning that we relies on bootloader to set the correct interface mode.

This patch added code to set interface correctly so that everything works
even if bootloader configures it wrong.(e.g. on WNDR3800 u-boot set
the second GMAC mode to RMII but it should be RGMII.)

Introduced "qca,mac-idx" for the difference in MII_CTRL register value.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-28 11:26:53 +02:00
John Crispin
9300eda00f ath79: replace patches
replace our downstream version of the patches with the ones
that were sent upstream.

Signed-off-by: John Crispin <john@phrozen.org>
2018-08-28 11:26:53 +02:00
Michal Cieslakiewicz
2e3e0fd94c ar71xx: WNR612v2: fix kernel panic due to wrong Wifi LED init
Netgear WNR612v2 flashed with recent OpenWrt builds suffers from kernel
panic at boot during wireless chip initialization, making device
unusable:

 ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
 ath: phy0: Enable LNA combining
 CPU 0 Unable to handle kernel paging request at virtual address 1000fee1, epc == 801d08f0, ra == 801d0d90
 Oops[#1]:
 CPU: 0 PID: 469 Comm: kmodloader Not tainted 4.9.120 #0
 [ ... register dump etc ... ]
 Kernel panic - not syncing: Fatal exception
 Rebooting in 1 seconds..

This simple patch fixes above error. It keeps LED table in memory after
kernel init phase for ath9k driver to operate correctly (__initdata
removed).

Also, another bug is fixed - correct array size is provided to function
that adds platform LEDs (this device has only 1 connected to Wifi chip)
preventing code from going outside array bounds.

Fixes: 1f5ea4eae4 ("ar71xx: add correct named default wireless led by using platform leds")

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[trimmed commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-28 07:21:01 +02:00
Matthias Schiffer
a4f4ddba61
ar71xx/generic: enable Zyxel NBG6616 in kernel config again
The NBG6616 shares a config symbol with the NBG6716. It was accidentally
removed from the config when the ar71xx-tiny target was split off.

Fixes: 0cd5e85e7a ("ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-08-27 20:27:25 +02:00
Matt Merhar
d03c89838e ath79: initial support for Ubiquiti RouterStation and RouterStation Pro
This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other
.dts files that utilize it, ar7161_ubnt_routerstation.dts and
ar7161_ubnt_routerstation-pro.dts.

The modifications to generic-ubnt.mk, config-default, and base-files
necessary for image generation, parsing RedBoot FIS partitions, network
configuration, and sysupgrade are also included.

This reintroduces vital bits from platform_do_upgrade_combined() and its
supporting functions to /lib/upgrade/platform.sh, which were previously
removed from ath79 in 3e9d9f6225 "ath79:
sysupgrade: drop unused platform checks". The new function is called
"routerstation_do_upgrade" and will *only* work for the RouterStation
series of boards. It does however retain the ability to downgrade (e.g.
from master -> 17.01.x using sysupgrade -F).

All hardware is functional including the AR8216 switch (for the Pro),
wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button,
and LED.

Switch and LAN/WAN configuration is the same as it is with the
equivalent ar71xx targets. MAC addresses are assigned based upon the
content stored in the RedBoot config partition.

Flashing via both sysupgrade and TFTP has been confirmed to work. Also,
the initramfs images are now raw .bin files instead of being wrapped in
a uImage (as they currently are in ar71xx), which makes them bootable
with RedBoot.

One notable difference to ar71xx is the inclusion of the RedBoot
"fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in
DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD
parser’s DT binding, whose proper usage is mutually exclusive to
defining a separate fixed-partitions node for "RedBoot config". This
config partition contains the board's base MAC address. The lack of a
hard-coded flash location means that the mtd-mac-address property cannot
be used in the .dts, so instead fconfig is used to read the MAC
addresses from flash in userspace during first boot.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-08-27 19:31:17 +02:00
Paul Wassi
e348ccc4e6 treewide: fix some cosmetic glitches in dts files
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-08-27 19:31:17 +02:00
Mathias Kresin
3601c3de23 ramips: fix mt7620 pinmux for second SPI
The mt7620 doesn't have a pinmux group named spi_cs1. The cs1 is part
of the "spi refclk" group. The function "spi refclk" enables the second
chip select.

On reset, the pins of the "spi refclk" group are used as reference
clock and GPIO.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-27 19:31:17 +02:00
Hauke Mehrtens
0f2787b9ff x86: geode: Add missing config options
This adds a configuration options which is needed now.
Without this patch the geode build will fail.

Fixes: 4eda2fddf2 ("x86/geode: enable X86_INTEL_LPSS to select PINCTRL")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-08-26 12:32:26 +02:00
Felix Fietkau
d45b5a061d ath79: fix mac address increment for embedded wireless Dorin
Use mtd-mac-address-increment-byte to match ar71xx behavior

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-08-25 19:18:08 +02:00
Felix Fietkau
a1f4ebcc87 kernel: make mtd mac address increment more flexible
Allow selecting the byte on which the increment should be added.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-08-25 19:18:08 +02:00
Tuomas Tynkkynen
5dd745588e brcm47xx: Enable USB power on WNDR3400v3
WNDR3400v3 needs GPIO 21 pulled high to enable power to USB ports. Add a
kernel patch to do that.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2018-08-25 16:27:17 +02:00
Vladimir Vid
6cda4f6861 imx6: Initial support for SolidRun CuBox-i devices based on i.MX6 processors (i1, i2, i2eX, and i4Pro).
- Specifications -

CuBox i1:
- SoC: i.MX6 Solo
- Cores: 1
- Memory Size: 512MB
- GPU: GC880
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps

CuBox i2 | i2eX:
- SoC: i.MX6 Dual Lite
- Cores: 2
- Memory Size: 1GB
- GPU: GC2000
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps

CuBox i4Pro | i4x4:
- SoC: i.MX6 Quad
- Cores: 4
- Memory Size: 2/4 GB
- GPU: GC2000
- Wifi/Bluetooth: Build In
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps

Built-in u-boot requires SPL (secondary program loader) to be present on the SD-card regardless of the image type which will be loaded.
SPL is generated by the u-boot-mx6cuboxi package which is preselected by the target device and can be found in bin/u-boot-mx6cuboxi directory.

Flashing the SPL:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=4
dd if=bin/targets/imx6/generic/u-boot-mx6cuboxi/SPL of=/dev/mmcblk0 bs=1K seek=1

Preparing the firmware on the SD-card:
(echo o; echo n; echo p; echo 1; echo ''; echo ''; echo w) | fdisk /dev/mmcblk0
mkfs.ext4 /dev/mmcblk0p1
mount /dev/mmcblk0p1 /mnt
tar -xzf bin/targets/imx6/generic/openwrt-imx6-device-cubox-i-rootfs.tar.gz -C /mnt/
mkdir -p /mnt/boot
cp bin/targets/imx6/generic/{*-uImage,*.dtb,*.scr} /mnt/boot/

Generated u-boot.img needs to be placed on the first partition:
cp bin/targets/imx6/generic/u-boot-mx6cuboxi/u-boot.img /mnt/

To boot from the SD card:

Boot script which sets mmc/dtb parameters and boots the board is automatically sourced.
If this does not work for any reason:
mmc dev 0; load mmc 0:1 $scriptaddr boot/boot.scr; source $scriptaddr

Currently imx6dl-cubox-i.dtb (Dual Lite) and imx6q-cubox-i.dtb (Quad) device trees are available.

Tested on i4Pro, MMC, USB (+ HiD), HDMI and ethernet ports are working.
Wireless and bluetooth are broken ATM. According to SolidRun forums, BCM4329/BCM4330 firmware is used which works fine on older kernels.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
2018-08-25 15:40:23 +02:00
Martin Schiller
17f30bfcf7 x86/64: enable X86_INTEL_LPSS to select PINCTRL
This makes it possible to use the MCP23S08 i/o expander
on x86_64 platforms with linux 4.14.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-08-25 15:33:51 +02:00
Martin Schiller
4eda2fddf2 x86/geode: enable X86_INTEL_LPSS to select PINCTRL
This makes it possible to use the MCP23S08 i/o expander
on geode platforms with linux 4.14.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-08-25 15:33:51 +02:00
Luis Araneda
64f4c3ef35 zynq: add support for the Zybo Z7 board
The board is manufactured by Digilent
Main features:
- Soc: XC7Z010 (Z7-10) or XC7Z020 (Z7-20)
- RAM: 1 GB DDR3L
- FLASH: 16 MB QSPI
- 1 Gbps Ethernet
- USB 2.0
- microSD slot
- Pcam camera connector
- HDMI Tx and Rx
- Audio codec: stereo out, stereo in, mic
- 5 (Z7-10) or 6 (Z7-20) Pmod ports
- 6 push-buttons, 4 switches, 5 LEDs
- 1 (Z7-10) or 2 (Z7-20) RGB LEDs

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-08-25 15:33:51 +02:00
Alex Maclean
894a95fa2d x86: add UHCI and XHCI USB host drivers to 4.14
Without UHCI a non-trivial number of machines will have no keyboard
without BIOS assistance.

Add XHCI as well in case there are chipsets which don't support legacy
interfaces, and support PCI OHCI controllers also.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-08-25 13:18:35 +02:00
Thibaut VARÈNE
bbe2cf657c ramips: fix RBM11G partitioning
This patch improves faf64056dd by correcting
the partition scheme for the "RouterBoot" section of the flash.

The partition scheme initially submitted is incorrect and does not reflect
the actual flash structure.

The "RouterBoot" section (name matching OEM) is subdivided in several
static segments, as they are on ar71xx RB devices albeit with different
offsets and sizes.
The naming convention from ar71xx has been preserved, except for the
bootloaders which are named "bootloader1" and "bootloader2" to avoid
confusion with the master "RouterBoot" partition.
The preferred 'fixed-partitions' DTS node syntax is used, with nesting
support as introduced in 2a598bbaa3.
"partition" is used for node names, with associated "label" to match
policy set by 6dd94c2781.

Leave a note in DTS to explain how the original author selected the SPI speed.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
2018-08-24 11:53:51 +02:00
Thibaut VARÈNE
b90cad2c2e ramips: fix RBM33G partitioning
This patch improves 5684d08741 by correcting
the partition scheme for the "RouterBoot" section of the flash.

The partition scheme initially submitted is incorrect and does not reflect
the actual flash structure.

The "RouterBoot" section (name matching OEM) is subdivided in several
static segments, as they are on ar71xx RB devices albeit with different
offsets and sizes.
The naming convention from ar71xx has been preserved, except for the
bootloaders which are named "bootloader1" and "bootloader2" to avoid
confusion with the master "RouterBoot" partition.
The preferred 'fixed-partitions' DTS node syntax is used, with nesting
support as introduced in 2a598bbaa3.
"partition" is used for node names, with associated "label" to match
policy set by 6dd94c2781.

The OEM source code also define a "RouterBootFake" partition at the
beginning of the secondary flash chip: to avoid trouble if OEM ever makes
use of that space, it is also defined here.

The resulting partition scheme looks like this:
[   10.114241] m25p80 spi0.0: w25x40 (512 Kbytes)
[   10.118708] 1 fixed-partitions partitions found on MTD device spi0.0
[   10.125049] Creating 1 MTD partitions on "spi0.0":
[   10.129824] 0x000000000000-0x000000040000 : "RouterBoot"
[   10.136215] 5 fixed-partitions partitions found on MTD device RouterBoot
[   10.142894] Creating 5 MTD partitions on "RouterBoot":
[   10.148032] 0x000000000000-0x00000000f000 : "bootloader1"
[   10.154336] 0x00000000f000-0x000000010000 : "hard_config"
[   10.160665] 0x000000010000-0x00000001f000 : "bootloader2"
[   10.167046] 0x000000020000-0x000000021000 : "soft_config"
[   10.173461] 0x000000030000-0x000000031000 : "bios"
[   10.190191] m25p80 spi0.1: w25q128 (16384 Kbytes)
[   10.194950] 2 fixed-partitions partitions found on MTD device spi0.1
[   10.201271] Creating 2 MTD partitions on "spi0.1":
[   10.206071] 0x000000000000-0x000000040000 : "RouterBootFake"
[   10.212746] 0x000000040000-0x000001000000 : "firmware"
[   10.307216] 2 minor-fw partitions found on MTD device firmware
[   10.313044] 0x000000040000-0x000000220000 : "kernel"
[   10.319002] 0x000000220000-0x000001000000 : "rootfs"
[   10.324906] mtd: device 9 (rootfs) set to be root filesystem
[   10.330678] 1 squashfs-split partitions found on MTD device rootfs
[   10.336886] 0x000000b40000-0x000001000000 : "rootfs_data"

Leave a note in DTS to explain how the original author selected the SPI speed.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
[rmilecki: dropped "RouterBootFake" partition]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-08-24 11:46:48 +02:00
Koen Vandeputte
6100655c8c ar71xx: fix typo in rb91x nand source
Fixes: 3b1ea0996f ("ar71xx: fix build error due to bad include")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-24 09:18:13 +02:00
Lech Perczak
4f3d700138 ath79: ubnt-xm: create mapping for RSSI LEDs
Ubiquiti XM series boards contain a set of RSSI LEDs. Create an UCI
mapping for them, so visual feedback on RSSI is available, when using
userspace RSSI monitor daemon.

Runtime tested using rssileds.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-08-23 22:42:15 +02:00
Lech Perczak
d40956a74c ath79: ubnt-xm: hijack LED4 as booting/failsafe
Create aliases for led-booting and led-failsafe pointing at
ubnt:green:link4 LED, forUbiquiti XM series, so visual feedback
on device status becomes available, in order to enter failsafe mode
via button. led-running and led-upgrade aliases are omitted to avoid
conflicting with RSSI LEDs when in normal operation.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-08-23 22:42:15 +02:00
Lech Perczak
7782715373 ath79: ubnt-xm: disable WAN on (rocket|bullet)-m
ubnt,bullet-m and ubnt,rocket-m targets support only single Ethernet
port, therefore disable creation of WAN zone and interfaces for them,
as their intended purpose is a wireless bridge. This aligns the
configuration with one found in ar71xx target.

ubnt,nano-m target is kept as is, being a two-port device.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-08-23 22:42:15 +02:00
Lech Perczak
614199c81d ath79: ubnt-xm: support ath9k firmware loading
Enable ath9k EEPROM extraction on boot for Ubiquiti XM-series boards.
This is required for wireless interface to function.
Runtime tested on Nanobridge M5.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-08-23 22:42:15 +02:00
INAGAKI Hiroshi
30b4f78193 ath79: add support for I-O DATA ETG3-R
I-O DATA ETG3-R is a wired router, based on Atheros AR9342.

Specification:

- Atheros AR9342
- 64 MB of RAM
- 8 MB of Flash
- 5x 10/100/1000 Ethernet
  - AR8327N
- 2x LEDs, 1x key
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using initramfs image:

1. Connect serial cable to UART header on ETG3-R
2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in
the TFTP directory
3. Set IP address of the computer to 192.168.0.10, connect to the
LAN port of ETG3-R, and start the TFTP server on the computer
4. Connect power cable to ETG3-R and turn on the router
5. Press "Enter" key when the "Hit any key to stop autoboot:" message
is displayed on the console and enter the u-boot cli
6. execute following commands to change kernel address for u-boot
  setenv bootsf 1
  setenv mtd_kernel1 "bootm 0x9f050000"
  saveenv
7. execute "tftpboot; bootm" command to download the initramfs image from
TFTP server and boot with it
8. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for ETG3-R
9. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-23 22:42:15 +02:00
Roger Pueyo Centelles
524c17d865 ramips: mt7620: add dir-810l network config
The device was not included in the /etc/board.d/02_network file, so
the network wouldn't be properly set up on boot.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-08-23 22:42:15 +02:00
NOGUCHI Hiroshi
ad10e71bec ramips: add support for ELECOM WRC-1900GST
ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A.
This is almost same as WRC-2533GST except wireless specs.

Specifications:

  - SoC : MT7621A (four logical CPU cores)
  - RAM : 128MiB
  - ROM : 16MiB of SPI NOR-FLASH
  - wireless :
          5GHz : 3T3R up to 1300Mbps/11ac with MT7615
          2.4GHz : 3T3R up to 600Mbps/11n with MT7615
  - Ethernet : 5 ports, all ports is capable of 1000base-T
  - Ether switch : MT7530 (MT7621A built-in)
  - LEDs : 4 LEDs
  - buttons : 2 buttons and 1 slide-switch
  - UART : header is on PCB, 57600bps

Flash instruction using factory image:

 1. Connect the computer to the LAN port of WRC-1900GST
 2. Connect power cable to WRC-1900GST and turn on it
 3. Access to "https://192.168.2.1/" and open firmware update
    page ("ファームウェア更新")
 4. Select the OpenWrt factory image and click apply ("適用")
    button
 5. Wait ~150 seconds to complete flashing

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
2018-08-23 22:42:09 +02:00
Mathias Kresin
b8996ea08a ramips: fix compatibles in SoC dtsi
The former used compatibles aren't defined anywhere and aren't used by
the devicetree source files including them.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-23 22:40:59 +02:00
Mathias Kresin
b88e03e2d4 ramips: fix GL-MT300N-V2 SoC compatible
According to abbfcc8525 ("ramips: add support for GL-inet
GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC
compatible to match the used hardware.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-23 22:40:59 +02:00
Mathias Kresin
28de86e816 ramips: drop not existing groups from pinmux
RT5350 neither have rgmii nor a mdio pinmux group. MT7628an doesn't
have a jtag group. Having these groups defined might cause a boot
panic.

The pin controller fails to initialise for kernels > 4.9 if invalid
groups are used. If a subsystem references a pin controller
configuration node, it can not find this node and errors out. In worst
case it's the SPI driver which errors out and we have no root
filesystem to mount.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-23 22:40:59 +02:00
Mathias Kresin
6b13238a13 generic: revert workarounds for AR8337 switch
The intention of 967b6be118 ("ar8327: Add workarounds for AR8337
switch") was to remove the register fixups for AR8337. But instead they
were removed for AR8327.

The RGMII RX delay is forced even if the port is used as phy instead of
mac, which results in no package flow at least for one board.

Fixes: FS#1664

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-23 22:40:59 +02:00
Koen Vandeputte
6b4ba118ac kernel: bump 4.14 to 4.14.66
Refreshed all patches

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-22 13:47:13 +02:00
Koen Vandeputte
7a9afb8783 kernel: bump 4.9 to 4.9.123
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-22 13:47:13 +02:00
Koen Vandeputte
3b1ea0996f ar71xx: fix build error due to bad include
While "rawnand.h" is available in kernel 4.14,
the default for this target is kernel 4.9 in which "nand.h" should be used.

Add an extra check to include the correct file depending on kernel version

Fixes these build errors:

drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory
 #include <linux/mtd/rawnand.h>
          ^~~~~~~~~~~~~~~~~~~~~
compilation terminated.

Fixes: 318e19ba67 ("ar71xx: add v4.14 support")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-22 13:11:59 +02:00
Koen Vandeputte
743654f30d ar71xx: add missing include for checking kernel version
Fixes these build errors:

arch/mips/ath79/mach-rb2011.c:20:5: error: "LINUX_VERSION_CODE" is not defined, evaluates to 0 [-Werror=undef]
 #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0)
     ^~~~~~~~~~~~~~~~~~
arch/mips/ath79/mach-rb2011.c:20:26: error: "KERNEL_VERSION" is not defined, evaluates to 0 [-Werror=undef]
 #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0)
                          ^~~~~~~~~~~~~~
arch/mips/ath79/mach-rb2011.c:20:40: error: missing binary operator before token "("
 #if LINUX_VERSION_CODE < KERNEL_VERSION(4,14,0)
                                        ^

Fixes: 318e19ba67 ("ar71xx: add v4.14 support")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-22 13:11:52 +02:00
John Crispin
318e19ba67 ar71xx: add v4.14 support
adds v4.14 patches for testing but leaves v4.9 as default for now.

Signed-off-by: John Crispin <john@phrozen.org>
2018-08-22 08:09:00 +02:00
Koen Vandeputte
548182bc6d kernel: bump 3.18 to 3.18.119
Refreshed all patches.

Compile-tested on: adm5120, adm8668, au1000, mcs814x, ppc40x, ppc44x, xburst
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-20 13:03:23 +02:00
Koen Vandeputte
ba30490d05 kernel: bump 4.9 to 4.9.122
Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-20 13:03:22 +02:00
David Bauer
98d3770379 ath79: fix TL-MR3020 image metadata
Sysupgrading to ath79 from ar71xx currently fails because of mismatching
supported_devices. ar71xx is expecting "tl-mr3020" which is missing in
the ath79 image. Upgrading from ath79 is unaffected, as the image
contains the old string for ar71xx and the new one coming from the
device-tree.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-19 18:58:04 +02:00
Chuanhong Guo
f195ab766c ath79: cleanup PISEN WMM003N image metadata
PISEN WMM003N is never supported by ar71xx, this commit also removed
SUPPORTED_DEVICES for it because it's completely useless.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-19 18:52:24 +02:00
David Bauer
3f8c5d5476 ath79: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.

SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM:   Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
USB:   1x USB 2.0
IN:    WPS button, WiFi button
OUT:   Power LED green, Internet LED green, WLAN LED green,
       LAN LED green, INFO LED green, INFO LED red
UART:  Header Next to Black metal shield
       Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
       The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (LAN + WAN)
 - WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

The USB port doesn't work. Both Root Hubs are detected as having 0 Ports:

[    3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.723267] usbcore: registered new interface driver usbfs
[    3.729058] usbcore: registered new interface driver hub
[    3.734616] usbcore: registered new device driver usb
[    3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.758357] SCSI subsystem initialized
[    3.766026] ehci-platform: EHCI generic platform driver
[    3.771548] ehci-platform ehci-platform.0: EHCI Host Controller
[    3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[    3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[    3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00
[    3.824001] hub 1-0:1.0: USB hub found
[    3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    3.835825] ehci-platform ehci-platform.1: EHCI Host Controller
[    3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[    3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[    3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00
[    3.894011] hub 2-0:1.0: USB hub found
[    3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    3.908928] usbcore: registered new interface driver usb-storage
[    3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/*

A few words about the shift-register:

AVM used a trick to control the shift-register for the LEDs with only 2
pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple
shift-registers, pulls the latch, moving the shift register-state to
the storage register. It also pulls down MR (normally pulled up) to
clear the storage register, so the latch gets released and will not be
pulled by the remaining bits in the shift-register. Shift register is
all-zero after this.

For that we need to make sure output 7 is set to high on driver probe.
We accomplish this by using gpio-hogging.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1).
Firmware can be uploaded like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-19 18:52:22 +02:00
Christian Lamparter
1c6e0f57a7 ath79: add support for TP-Link Archer C7 v1
TP-Link Archer C7 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

 - 720 MHz CPU
 - 128 MB of RAM (Various chips)
 - 8 MB of FLASH (Various chips)
 - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
 - minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!)
 - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
 - 10x LEDs, 2x software buttons

For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c7-1750>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-08-19 18:48:43 +02:00
INAGAKI Hiroshi
ff4bc483fc ath79: add support for I-O DATA WN-AC1167DGR
I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- Qualcomm Atheros QCA9557
- 128 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz wifi
  - 2.4 GHz: SoC internal
  - 5 GHz: QCA988x
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1167DGR
2. Connect power cable to WN-AC1167DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-16 21:20:57 +02:00
Johann Neuhauser
94ee5e3d1d ath79: fix leds and network for TP-Link TL-WR841 v9/v11
Adding tl-wr841-v11 and the rename of tl-wr841n-v9 to tl-wr841-v9 in 01_leds
and 02_network script files are missing in commits cc35c91 and 8db6522.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[merged with identical case in 02_network]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
3f09adaa55 ath79: don't use the pcs,cr5000 wps led as usb led
If it isn't a usb led, it shouldn't be used as one by default. It is up
to the user to add such a (mis)configuration for the board.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Dmitry Tunin
0c5a532553 ath79: add support for TP-Link MR-3040 v2
Add support for the ar71xx supported TP-Link MR-3040 v2.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-16 21:20:57 +02:00
INAGAKI Hiroshi
9e6f22e309 ath79: add support for Buffalo WHR-G301N
Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240.
Ported from ar71xx target.

Specification:

- Atheros AR7240
- 32 MB of RAM
- 4 MB of Flash
- 2.4 GHz 2T2R wifi
- 5x 10/100 Mbps Ethernet
- 9x LEDs, 4x keys
  - LED: 8x gpio-leds, 1x ath9k-leds
  - key: 2x buttons, 1x slide switch
- UART header on PCB
  - Vcc, GND, TX, RX from LEDs side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WHR-G301N
2. Connect power cable to WHR-G301N and turn on it
3. Access to "http://192.168.11.1/" and open firmware update page
("ファーム更新")
4. Select the OpenWrt factory image and click execute ("実行") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[fix the SUPPORTED_DEVICES to be compatible with the ar71xx image]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
c9e9a78734 lantiq: add support for upgrade led
Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh
script en par with the other implementations using devicetree aliases
to define multiple leds for boot status indication.

By default, use the boot finished led to indicate an upgrade for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
be06c726c4 treewide: drop unused get_status_led functions
The function isn't used for targets getting the status leds from the
devicetree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
dd448cd276 treewide: fix upgrade led handling
The upgrade led is only used if a running led is defined. If no running
led is defined, the upgrade led is ignored and upgrade isn't indicated
at all.

Instead, turn off the running led prior to turning the upgrade led on.
In most cases there isn't any visual change, but it allows to use an
independent led for upgrade indication.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
56b8ac1e86 treewide: consolidate upgrade state set
Set the (sys)upgrade state when sourcing the stage2 script instead of
setting the state for each target individual.

This change fixes the, due to a missing state set, not working upgrade
led on ath79 and apm821xx.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
1ea1f3a223 ramips: mt7620: fix bad indent
Fix the indent to make the make it obvious which condition is the
parent of the loop.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
22ae14d0e7 cns3xxx: fix mtu setting with kernel 4.14
Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device
min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which
is [68, 1500] by default.

It's necessary to set a max_mtu if a mtu > 1500 is supported.

Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Hauke Mehrtens
b547ab3143 kernel: bump kernel 4.9 to version 4.9.120
The following patch was integrated upstream:
 * target/linux/generic/backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

This fixes tries to work around the following security problems:
 * CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
 * CVE-2018-3646 L1 Terminal Fault Virtualization related aspects

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-08-15 22:32:07 +02:00
Hauke Mehrtens
e4bad5f0ac kernel: bump kernel 4.14 to version 4.14.63
The following patches were integrated upstream:
 * target/linux/ipq40xx/patches-4.14/050-0006-mtd-nand-qcom-Add-a-NULL-check-for-devm_kasprintf.patch
 * target/linux/mediatek/patches-4.14/0177-phy-phy-mtk-tphy-use-auto-instead-of-force-to-bypass.patch

This fixes tries to work around the following security problems:
 * CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
 * CVE-2018-3646 L1 Terminal Fault Virtualization related aspects

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-08-15 22:31:56 +02:00
Dmitry Tunin
ae9c3105a3 ath79: use both WNDR3x00 power leds for boot status indication
Use the orange led by default to match the bootloader/stock firmware
behaviour. Turn on the green power led after boot to indicate a
finished boot and the orange one off.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message, keep orange power led enabled during early
kernel boot]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00
Dmitry Tunin
3d9610aa13 ath79: use both DIR-825 B1 power leds for boot status indication
Use the orange led by default to match the bootloader/stock firmware
behaviour. Turn on the blue power led after boot to indicate a finished
boot and the orange one off.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message, keep orange power led enabled during early
kernel boot]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00
Dmitry Tunin
7a873974f7 ath79: add support for indicating the boot state using multiple leds
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00
Cezary Jackiewicz
37af596593 ramips: add support for D-Link DWR-118-A2
The DWR-118-A2 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612EN)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN)
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- GELAN not working
- flash is very slow

The status led has been assigned to the dwr-118-a2:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-08-15 07:42:36 +02:00
Pawel Dembicki
4877ad44c7 ramips: mt7620: enable all ports unconditionally
This patch make all mt7620 ephy ports turned on.
It is necessary for some JBOOT devices.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-08-15 07:42:36 +02:00
Deng Qingfang
d20f4fc628 ramips: add support for HiWiFi HC5861B
HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN
https://www.hiwifi.com/enjoy-view

Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7612EN 802.11ac 2T2R 867Mbps
- 5x 10/100 Mbps Ethernet

Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot

Everything is working

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-08-14 10:21:32 +02:00
Chuanhong Guo
1213504750 ath79: add support for TP-Link TL-WR941N/ND v2/v3
Specification:
- SoC: Atheros AR9132
- Flash: 4 MB
- RAM: 32 MB
- Ethernet: Marvell 88E6060 with 5 FE ports.

Flash instruction:
  Upload the generated factory firmware on web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-14 10:19:37 +02:00
Johann Neuhauser
8db6522531 ath79: add support for TP-Link WR841N/ND v11
Specification:
- SoC: Atheros AR9533
- Flash: 4 MB
- RAM: 32 MB
- Ethernet: 4x LAN (100M) / 1x WAN (100M)
- WiFi: 2.4G 300M

Flash instruction:
  Flash factory image from stock WebUI.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-08-14 10:19:37 +02:00
Johann Neuhauser
18f738d3c4 ath79: move TP-Link WR841v9 aliases node from dtsi to dts
Move the alias node of the TP-Link WR841v9 and rename the phandle of
the qss led to qss_led in preparation for adding the very similar
TP-Link WR841v11.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-08-14 10:19:37 +02:00
Johann Neuhauser
cc35c91f56 ath79: fix sysupgrade TP-Link WR841v9
Remove SUPPORTED_DEVICES from wr841-v9 because it´s not needed and
for consistency rename everything to tl-wr841-v9.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-08-14 10:19:37 +02:00
Hannu Nyman
437e35f8a3 ath79: Add wifi to WNDR3700, WNDR3700v2 and WNDR3800
Add ath9k wifi capabilities to WNDR3700 family.

* use kmod-owl-loader to load firmware from "art"
* add wifi to DTS
* add wifi LEDs

Avoid using the same MAC for eth0 LAN and wlan0 by
toggling the eth0 MAC into a locally administered MAC.
That is currently done by in user-space by adding a
uci config item into /etc/config/network
(More elegant solution might be setting it already in
preinit phase.)

Known issues:

* wifi firmware file may not get created on the first boot
  after flashing on time to bring wifi normally up. Likely
  the overlay jffs2 is not yet ready for creating the
  firmware file. "wifi up" may still bring wifi up.
  Wifi will work normally at subsequent boots.

* phy0 and phy1 may get assigned mixed, so that phy0 may
  be the 5GHz radio instead of the normal 2.4GHz, and vice
  versa for phy1. Does not happen always, but may happen.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[fix the wifi unit address in the dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-14 10:19:37 +02:00
Icenowy Zheng
b2a33d5463 ath79: add support for Pisen WMM003N (Cloud Easy Power)
Pisen WMM003N (sold under the name of Cloud Easy Power) is an
AR9331-based router and power bank combo device. The device uses a
stock firmware modified from OpenWRT for TP-Link TL-WR703N; however
some GPIO definition is different on this device with TL-WR703N. An
AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also
added, and the stock Flash/RAM configuration is 8MiB/64MiB.

The stock firmware is an old and heavily modified OpenWRT-based
firmware, which has telnetd defaultly open, and the root password is
"ifconfig" (quotation marks not included). The factory image format is
not known yet, however the stock firmware ships the OpenWRT's sysupgrade
command, and it can be used to install a newer firmware.

Due to the lack of the access to the STM8 embedded controller, the SD
slot is currently not usable (because it's muxed with the on-board USB
port) and the AXP PMIC cannot be monitored.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
2018-08-14 10:19:37 +02:00
Koen Vandeputte
ee9e0c1deb ar7: remove linux 3.18 support
This target is on 4.9 currently.
It seems the support for this old kernel never got dropped.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-13 17:10:39 +02:00
Zoltan HERPAI
d6844b3bfa ramips: add missing USB packages into ASL26555-16M
Mirror the package list from the 8M device profile to the
16M device profile.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-08-13 10:26:03 +02:00
Peter Lundkvist
3337f202d6 ath79: drop tl prefix for TP-Link RE450 v2
This router is called RE450 and the tl prefix was used to identify it
as a TP-Link device. Drop the tl prefix since we now have tplink in
dts and device name.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-08-13 08:51:31 +02:00
Christian Lamparter
f3ffac90bc ath79: gmac: add parsers for rxd(v)- and tx(d|en)-delay for AR9344
Some AR9344 boards do very poorly with the default settings and
need custom rxdv-delay, rxd-delay, txd-delay, txen-delay flags
to perform reasonably.

In this case the WD My Net Wi-Fi Range Extender can not even
manage 10Mbps on a 1Gbit link:

root@AR9344:~# iperf3 -s
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from client [...]
[  5] local [...] connected to client
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  1.09 MBytes  9.16 Mbits/sec
[  5]   1.00-2.00   sec   895 KBytes  7.33 Mbits/sec
[  5]   2.00-3.00   sec   762 KBytes  6.25 Mbits/sec
[...]
[  5]  10.00-10.03  sec  17.0 KBytes  4.74 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.03  sec  9.00 MBytes  7.52 Mbits/sec

with but with the correct settings in place, it does much better:

root@AR9344:~# iperf3 -s
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from client [...]
[  5] local [...] connected to client
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  23.1 MBytes   193 Mbits/sec
[  5]   1.00-2.00   sec  23.1 MBytes   194 Mbits/sec
[  5]   2.00-3.00   sec  23.2 MBytes   195 Mbits/sec
[...]
[  5]  10.00-10.04  sec   710 KBytes   180 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.04  sec   237 MBytes   198 Mbits/sec

The tx data and enable delay bits definitions are taken from Atheros'
AR9344 Data Sheet Section "8.6.1 Ethernet Configuration (ETH_CFG)" on
page 153.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-08-13 08:48:37 +02:00
David Bauer
7d1b742b4d ath79: add QCA956x GMAC config
This commit adds the ability to configure the GMAC of the QCA956x.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-13 08:43:15 +02:00
Paul Wassi
2276bc0082 brcm47xx: cosmetic fix in model detection
In "brcm47xx: rework model detection" the file 01_detect was moved
to 01_network, therefore also update the warning message in case
everything fails.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-08-13 08:37:19 +02:00
Chuanhong Guo
cf50f72069 ath79: ar913x: fix eth pll register
PLL for eth0 internal clock on ar913x is at 0x18050014
and AR913X_ETH0_PLL_SHIFT is 20 instead of 17

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-13 08:37:19 +02:00
Chuanhong Guo
42b3fdf981 ath79: ag71xx: fix speed applied to MII0/1_CTRL on ar71xx/ar913x
Currently speed value is applied to interface mode field.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-13 08:37:19 +02:00
Hannu Nyman
4dc7cb792a ath79: add WNDR3700 and WNDR3700v2
Add support for WNDR3700 and WNDR3700v2.

They share most things with WNDR3800.
Only device IDs and partition structure needs to be set.

Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has
      also the NA version of the factory image.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-08-13 08:37:19 +02:00
Hannu Nyman
b58df9919e ath79: create WNDR3700 series .dtsi and adjust WNDR3800
Prepare for addition of WNDR3700 and WNDR3700v2 by
separating the common parts into wndr3700.dtsi and
leaving just the device-specific things into wndr3800.dts

The three routers are identical except
  * device IDs
  * WNDR3700 (v1) has only 8 MB flash, while others have 16 MB.
    Partition structure needs to be defined for each device.
  * (WNDR3800 has 128 MB RAM, but RAM size is not in DTS)

Also separate the common parts of the image recipe.
(Drop also the initramfs recipe.)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-08-13 08:37:19 +02:00
Daniel Gimpelevich
1d3ea7874d ramips: fix BR-6478ACv2 support
The wholesale changes introduced in commit f9b8328 missed this DTS file
because it hadn't been merged yet. This patch brings it in line to match
the other mt7620a devices' DTS files.

Additionally, the Internet LED is now labeled correctly and set to unused
by default, since the WAN interface is not known in every configuration.

Using sysupgrade between images before and after this commit will require
the -F flag.

Tested-by: Rohan Murch <rohan.murch@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[drop internet led default setting]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-13 08:37:19 +02:00
Ludwig Thomeczek
5543d63fc8 ramips: add support for Netgear R6120
This patch adds support for the Netgear R6120, aka Netgear AC1200.

Specification:
- SoC: MediaTek MT7628 (580 MHz)
- Flash: 16 MiB
- RAM: 64 MiB
- Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E)
- LAN speed: 10/100
- LAN ports: 4
- WAN speed: 10/100
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

To flash use nmrpflash with the provided factory.img.
Flashing via webinterface will not work, for now.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2018-08-13 08:37:19 +02:00
Hauke Mehrtens
31aeae0774 at91: do not build image for at91-q5xr5
The kernel image of the at91-q5xr5 is getting too bing now and this is
breaking the build. Remove the image for the at91-q5xr5 from the build
to at least build images for the other devices.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-08-12 11:34:50 +02:00
Chuanhong Guo
8e4e545ecb ath79: fix eth pll for ar913x
PLL node is missing syscon in compatible string.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-11 21:46:18 +02:00
INAGAKI Hiroshi
a6369206fe ath79: add support for I-O DATA WN-AC1600DGR2
I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- Qualcomm Atheros QCA9557
- 128 MB of RAM
- 16 MB of Flash
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 3T3R (QCA9880)
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR2
2. Connect power cable to WN-AC1600DGR2 and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-11 21:45:06 +02:00
Dmitry Tunin
97de133368 ath79: add support of D-Link DIR-825 B1
Add support for the ar71xx supported D-Link DIR-825 B1 to ath79.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-11 21:45:04 +02:00
Christian Lamparter
a441c86d93 ath79: add ath9k calibration data MAC addresses patching
This patch copies over the MAC patching helper functions from lantiq's
target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
file.

Not all vendors bothered to write the correct MAC addresses for the
ath9k wifi into the calibration data. And while ath9k does have some
special dt-properties to extract the addresses from a fixed position,
there are still devices that require userspace to edit or modify
the caldata.

In my case, the MAC address for the Wi-Fi device is stored in an
unsorted key-value based "nvram" database and there's an existing
userspace tool to extract the data.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-08-11 21:36:27 +02:00
Chuanhong Guo
d4e3a31f6c ath79: add support for TP-Link TL-WDR4900 v2
Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 8 MB
- RAM: 128 MB
- Ethernet: AR8327N with 5 GE ports.
- Wireless radio: QCA9558 for 2.4G and AR9580 for 5G.

Flash instruction:
  Upload the generated factory firmware on web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-11 21:36:27 +02:00
Koen Vandeputte
0ddb34b6b5 kernel: bump 4.14 to 4.14.62
Refreshed all patches.

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-10 18:43:23 +02:00
Koen Vandeputte
21a229317f kernel: bump 4.9 to 4.9.119
Refreshed all patches.

Delete upstreamed patch:
- 100-tcp-add-tcp_ooo_try_coalesce-helper.patch

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-10 18:43:23 +02:00
David Bauer
c4931713df ath79: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-09 18:44:57 +02:00
Chuanhong Guo
387736af41 ath79: ag71xx: remove PHY reset
Bit 8/12 of reset controller which is marked as PHY_RESET/SWITCH_RESET
in datasheets will trigger either a reset for builtin switch or assert
an external ETH0_RESET_L/ETH1_RESET_L pin, which are usually connected
to external PHY/switch. None of them should be triggered every time an
interface is brought up in ethernet driver.

Remove PHY reset support from ag71xx and definition for them in dtsi.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-09 18:44:57 +02:00
INAGAKI Hiroshi
23519edbca ath79: add support for Buffalo BHR-4GRV2
Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros
QCA9558.
Ported from ar71xx target.

Specification:

- Qualcomm Atheros QCA9558
- 64 MB of RAM
- 16 MB of Flash
- 5x 10/100/1000 Ethernet
  - QCA8337N
- 4x LEDs, 2x keys
- UART header on PCB
  - Vcc, TX, RX, GND from LED side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of BHR-4GRV2
2. Connect power cable to BHR-4GRV2 and turn on it
3. Access to "http://192.168.12.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新実行")
button
5. Wait ~120 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-09 18:44:57 +02:00
David Bauer
6555612783 ath79: fix PLL settings for QCA955x
This adds PLL settings for the ethernet ports of the TP-Link TL-WR1043
v2/v3 and the Openmesh OM5P-AC-v2.

We also change the PLL-settings in the qca9557.dtsi to match the ones
used as default on the ar71xx target.

As of 4b9680f138 those devices have broken ethernet ports as the default
PLL settings defined in the QCA9557.dtsi are applied which are off for
those devices.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-09 17:24:39 +01:00
Kevin Darbyshire-Bryant
995a1ba841 ath79: add pll for archer c7
commit 4b9680f fixed pll settings and the correct pll set
by bootloader is overrided by value in qca9557.dtsi which
is incorrect for Archer C7 and breaks ethernet. Add pll
values for archer c7 to fix ethernet connection.

This individual pll tweak has been cherry picked from github pr 1260
which changes a couple of things in a single commit and should be
ideally split.  This commit get archer v7 back and working.

Tested: archer c7 v2

Original combined commit authored by:
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
c7 fix only split out by:
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-08-09 17:04:59 +01:00
Antonio Silverio
5f4502998a sunxi: change Orange Pi PC2 MUSB/power button
Changed default role of Orange Pi PC2 MSUB port to host (in dts)
Changed default function of Orange Pi PC2 power button to PWR_BTN

Signed-off-by: Antonio Silverio <menion@gmail.com>
2018-08-09 12:07:10 +02:00
Antonio Silverio
e2e39328d5 sunxi: Added support for Xunlong Orange Pi PC2
CPU: H5 High Performance Quad-core 64-bit Cortex-A53
GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL
Memory: 1GB DDR3 (shared with GPU)
Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB)
Onboard Network: 1000M/100M Ethernet RJ45
USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode
role by default in DTS
Buttons: Power Button(SW4) Debug TTL

UART: ..DC-IN..
>[GND][RX][TX] ..HDMI..

Signed-off-by: Antonio Silverio <menion@gmail.com>
2018-08-09 12:06:58 +02:00
Stijn Tintel
14b6c72541 kernel: move e1000e patches to backports
They're already in linux.git, so they shouldn't be in pending.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-08-09 11:46:29 +02:00
Koen Vandeputte
915b0ba694 cns3xxx: correct size specifier in watchdog init print
fix compiler warnings

Fixes: 84acff2865 ("cns3xxx: fix mpcore watchdog")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-08 16:05:16 +02:00
Koen Vandeputte
85a0bca7cf cns3xxx: delete invalid snip in patch
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-08 16:05:16 +02:00
David Bauer
4e39e213af ar71xx: allow to override at803x sgmii aneg status
When checking the outcome of the PHY autonegotiation status, at803x
currently returns false in case the SGMII side is not established.

Due to a hardware-bug, ag71xx needs to fixup the SoCs SGMII side, which
it can't as it is not aware of the link-establishment.

This commit allows to ignore the SGMII side autonegotiation status to
allow ag71xx to do the fixup work.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-08 15:49:24 +02:00
David Bauer
f4f99ec973 ar71xx: fix QCA955X SGMII link loss
The QCA955X is affected by a hardware bug which causes link-loss of the
SGMII link between SoC and PHY. This happens on change of link-state or
speed.

It is not really known what causes this bug. It definitely occurs when
using a AR8033 Gigabit Ethernet PHY.

Qualcomm solves this Bug in a similar fashion. We need to apply the fix
on a per-device base via platform-data as performing the fixup work will
break connectivity in case the SGMII interface is connected to a Switch.

This bug was first proposed to be fixed by Sven Eckelmann in 2016.
 https://patchwork.ozlabs.org/patch/604782/

Based-on-patch-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-08 15:48:57 +02:00
David Bauer
fbe17867da kernel: allow device-tree configuration of at803x
This commit adds the ability to configure specific functions of the
at803x series ethernet-PHYs, which were previously configured
exclusively with the help of platform-data, via device-tree.

This is needed to fully support existing boards of the ar71xx platform.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-08 15:44:33 +02:00
Jo-Philipp Wich
fefe1da440 kernel: backport upstream fix for CVE-2018-5390
Backport an upstream fix for a remotely exploitable TCP denial of service
flaw in Linux 4.9+.

The fixes are included in Linux 4.14.59 and later but did not yet end up in
version 4.9.118.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-08 14:50:31 +02:00
David Bauer
4b9680f138 ath79: fix QCA9557 eth PLL settings
The QCA9557 dtsi is currently missing pll-handle and pll-regs for both
eth0 and eth1, therefore PLL settings won't be applied. This commit
fixes this behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-08 08:38:45 +02:00
Kristian Evensen
ddf64edfe1 mediatek: Fix amount of memory on U7623
While finalizing support for the U7623 with 512MB, I made an embarresing
error and configured 1GB RAM for the board. I also forgot to move memory
from the dtsi and to the dts. This commit takes care of my mistakes.

While I am confessing my mistakes, I also note that I made a mistake in
the commit message of the initial U7623 commit. It is the .bin-file, and
not the .gz file that shall be sent to the device via tftp.

v1->v2:
* Remove redundant memory node (thanks Jonas Gorski)

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2018-08-08 08:38:45 +02:00
Mathias Kresin
b94b4b0862 ath79: don't include tl-wdr3600 image build code for tl-wdr4300
Including the tl-wdr3600 image build code just to overwrite most of it
doesn't make much sense and only makes it hard to read.

Furthermore, the tl-wdr4300 image will be marked as compatible with the
tl-wdr3600 this way.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Mathias Kresin
12121e643b ath79: cleanup netgear wnr612-v2 supported devices
The netgear,wnr612-v2 is included by default based on the device
define.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Mathias Kresin
38877d8873 ath79: mark netgear variables as device specific
The variables are used in image build recipes and need to be marked as
per devices vars to be stored individual per image define. Otherwise
the last defined variable will be used for all boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Chuanhong Guo
1edba538a9 ath79: Fix led nodes for TL-WR740N v2 and add its clones
This patch did the following things:
1. Separate ath9k-leds out of gpio leds so that all other leds will work
   before ath9k loded (e.g. during preinit/init stage).
2. Rename wps led to qss since that's how TP-Link mark it.
3. Rename LED prefix to tp-link because that dts is shared by many devices.
4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1.
   (This will require a forced sysupgrade if you comes from
   the previous wr740n v2 image.)
5. Remove SUPPORTED_DEVICES.
   (tl-wr740n-v2 doesn't exist anywhere so it's useless.)
6. Add all WR741ND v1 clones found in ar71xx.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-08 08:11:11 +02:00
Mathias Kresin
55ff2951ea ath79: fix dts warnings
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Mathias Kresin
bf078fcab6 ath79: fix node names
Use the standardized node names from the devicetree specification.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:22 +02:00
Mathias Kresin
a8ad7b6efa ath79: fix compatible strings
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:22 +02:00
Mathias Kresin
7b42247182 ath79: fix whitespace issue in dts files
Fixes spaces vs. tabs issues and remove indentation on blank lines.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:22 +02:00
Mathias Kresin
3b1213a377 ramips: use #include syntax for dtsi files
Use the same syntax for including dtsi for all dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:03 +02:00
Koen Vandeputte
0d283c0180 cns3xxx: ethernet: use circular queue checks consistently
Use the same method for setting queue index pointers consistenly
throughout the source file.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-07 12:53:48 +02:00
Koen Vandeputte
06beefd6d5 cns3xxx: ethernet: cleanup code
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-07 12:53:48 +02:00
Koen Vandeputte
23cdbf2644 cns3xxx: ethernet: fix signed/unsigned comparison
Fixes a compiler warning

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-07 12:53:47 +02:00
Koen Vandeputte
d1aa6bd698 cns3xxx: add myself as maintainer
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-07 12:53:47 +02:00
Koen Vandeputte
7a254aeeb8 kernel: bump 4.14 to 4.14.61
Refreshed all patches.

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-07 12:53:47 +02:00
Koen Vandeputte
f7036a34ac kernel: bump 4.9 to 4.9.118
Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-07 12:53:47 +02:00
Chuanhong Guo
18a2595315 ath79: rename tl-archer-c7 to archer-c7
This router is called Archer C7 and the tl was used to identify
TP-LINK. Since we have added tplink in dts/board name, the tl
prefix is useless now.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
2d5fee248c ath79: alphabetical order image/generic.mk
Move the wzr-hp-g450h in image/generic.mk to keep alphabetical order.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
8288af1e18 ath79: rename dts/image using manufacturer_board scheme
This helps getting rid of SUPPORTED_DEVICES which can be
auto-generated in image/Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
2da431e583 ath79: remove quotes for boardname in scripts
Quotes are not required in case statements.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
f9065e44a6 ath79: put all devices in alphabetical order in scripts
And remove specifying lan interfaces as eth1.1 because this is
handled by ucidef_add_switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
3804134369 ath79: fix support for TL-MR3020 v1
Change lan and it's LED to eth0
It's broken since c7c807cb8c
where I changed the dts but forgot to change default configurations.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
690c55e8cc ath79: fix support for TL-WR740N/WR741N v4
1. Swap eth0/eth1
 Both devices are using AR9331, the builtin switch on AR9331 is
 connected to gmac1 and gmac1 is named as eth1 in ath79.
 PS: gmac1 is eth0 and gmac0 is eth1 in ar71xx because of the
 reversed initialization order.
2. Fix the incorrect compatible string in dts

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
115e993adc ath79: remove useless phy-handle nodes
phy-handle is used to poll link status. They are useless when
we need fixed-link on these interfaces.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Christian Lamparter
3fce12568a kernel: modules: fix kmod-regmap redux
Jonas Gorski commented on the previous patch:
|This is actually the wrong fix and papers over an issue in one of our
|local patches.
|
|We intentionally allow regmap to be built as a module, see
|
|/target/linux/generic/hack-4.14/259-regmap_dynamic.patch
|[...]
|[The regulator code] optionally supports regmap thanks to the stubs
|provided if regmap is disabled - which breaks if you compile regmap
|as a module.

In order to mitigate this issue, this patch reverts the previous patch
and replaces the existing IS_ENABLED(CONFIG_REGMAP) with
IS_REACHABLE(CONFIG_REGMAP). This solves this particular issue as the
regulator code will now automatically fallback to the regmap stubs in
case the kmod-regmap module is enabled, but nothing else sets
CONFIG_REGMAP=y.

Note: There's still a potential issue that this patch doesn't solve:
If someone ever wants to make a OpenWrt kernel package for a
regulator module that requires the REGMAP feature for a target that
doesn't set CONFIG_REGMAP=y but has CONFIG_REGULATOR=y, the resulting
kmod-regulator-xyz package will not work on the target.
Luckily, there aren't any in-tree OpenWrt kernel module packages for
regulators at the moment. On the bright side: regmap is a critical
part nowadays and all new and upcoming architectures require it by
default. This will likely only ever be a problem for legacy targets
and devices that cannot afford to enable REGMAP.

Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
Fixes: d00913d121 ("kernel: modules: fix kmod-regmap")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-08-06 07:17:12 +02:00
Chen Minqiang
f6d81e2fa1 mt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible
To share mdio addr for IntPHY and ExtPHY,
as described in the documentation (MT7620_ProgrammingGuide.pdf).
(refer: http://download.villagetelco.org/hardware/MT7620/MT7620_ProgrammingGuide.pdf)

when port4 setup to work as gmac mode, dts like:

&gsw {
    mediatek,port4 = "gmac";
};

we should set SYSCFG1.GE2_MODE==0x0 (RGMII).
but SYSCFG1.GE2_MODE may have been set to 3(RJ-45) by uboot/default
so we need to re-set it to 0x0

before this changes:
gsw: 4FE + 2GE may not work correctly and MDIO addr 4 cannot be used by ExtPHY

after this changes:
gsw: 4FE + 2GE works and MDIO addr 4 can be used by ExtPHY

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-08-06 07:12:31 +02:00
Daniel Gimpelevich
379fe50672 ramips: fix gigabit switch PHY access on MDIO
When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.

Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Daniel Gimpelevich
5a6229a93d ramips: remove superfluous & confusing DT binding
Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Daniel Gimpelevich
f72fa883b3 ramips: add support for Edimax BR-6478AC v2
Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie.
Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated.

Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Macronix MX25L6405D
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7612E 5GHz 802.11ac
- Switch: Mediatek MT7530W Gigabit Switch
- USB: Yes 1 x 2.0

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
4. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Paul Spooren
ad5c2897ec imagebuilder: manifest function show stderr
This really simplifies debugging, if a package is not found or a feed is
not reachable, a proper stderr is printed. Currently it would only say
`_call_manifest` failed.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2018-08-06 06:54:42 +02:00
Alex Maclean
6031ab345d ramips: move partitions into partition table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-08-04 08:39:35 +02:00
Mathias Kresin
6dd94c2781 ramips: unify partition node names in dts files
Use partition@ as name for all partition nodes. Add a label where
necessary.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
bfd65fc4ab ramips: fix whitespace and comment issues in dts
Fix space vs. tabs issue and trainling whitespaces. Use C style
comments or drop the comments if they explain what is already to see in
the devicetree parameters.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
53624c1702 ramips: fix dtc warnings
Fix individual boards dtc warnings or obvious mistakes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
6384e0d16a ramips: fix hnat dtc warning
The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.

Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
f9b8328d79 ramips: fix pci/pcie related dtc warnings
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.

Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.

Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.

If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.

Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.

Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
d8e7a526a3 ramips: use ralink,nr-gpio instead of ralink,num-gpios
Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.

Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
1bad2b74ae ramips: fix cpu interrupt controller dtc warnings
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
b9dbf3f3c8 ramips: fix cpu related dtc warnings
We need a reg property if we are using a unit address.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
René van Dorst
0ae9396556 treewide: convert gpio-export to platform driver
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.

gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.

Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
1d18a14a90 ath79: really fix TP-Link Archer C7 v2 MAC address
Revert 290c54473e ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.

Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.

The correct MAC adress increments for this board are:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

Fixes: FS#408

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Koen Vandeputte
f960490fc8 kernel: bump 4.14 to 4.14.60
Refreshed all patches

Removed upstreamed patches:
- 500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-03 16:10:38 +02:00
Koen Vandeputte
4ec4dd2a11 kernel: bump 4.9 to 4.9.117
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-03 16:10:38 +02:00
Jo-Philipp Wich
4bb8a678e0 sdk: include arch/arm/ Linux includes along with arch/arm64/ ones
The Linux headers on arm64 architectures contain references to common
arch/arm/ headers which were not bundled by the SDK so far.

Check if we're packing the SDK for an arm64 target and if we do, also
include arch/arm headers as well.

Fixes FS#1725.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-03 13:47:29 +02:00
Jonas Gorski
2308b87204 brcm63xx: switch to 4.14
Kernel 4.14 support has been present for quite some time, so let's give
it wider testing.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:49:18 +02:00
Jonas Gorski
15cb65dad7 brcm63xx: drop b43 from devices with unsupported wifi
The internal wifi isn't supported, so drop b43 from devices that only
have it.

Fixes FS#1698
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Jonas Gorski
8cb8d70fea brcm63xx: copy SR102 support patch to 4.14 as well
It seems to have been missed when the patch was accepted.

Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Jonas Gorski
bc1c706bb3 brcm63xx: drop bogus SPROM section from SR102
The integrated SoC wifi will likely never be supported, and if,
it will go through DT with the sprom contents there.

Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Andrew Cameron
bae927c551 ar71xx: add support for TP-LINK CPE510 V2.0
Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2018-08-02 07:49:26 +02:00
Jo-Philipp Wich
b9bd3285c7 Revert "ar71xx: ag71xx: Prevent kernel oops for board def"
This reverts commit 7a3e133751.

This change reportedly breaks connectivity on some ar71xx devices, so
revert it for now.

Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:34:22 +02:00
Jo-Philipp Wich
33dbe2c55d Revert "ar71xx: ag71xx: Add connect message: fixed phy"
This reverts commit 0b9f4e8808.

This change reportedly breaks connectivity on some ar71xx devices, so
revert it for now.

Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:31:37 +02:00
Jo-Philipp Wich
9ebf596386 Revert "ar71xx: ag71xx_phy: Fix compilation for debug messages"
This reverts commit 2655fbe8ef.

The patch introduces syntax errors, revert it for now.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:31:14 +02:00
Daniel F. Dickinson
0b7a9688ce ar71xx: cr3000: cleanup board definition
1) Add comments so it's clear why we did things; this may prevent
   someone (e.g. me) from sinking time into fixing things that
   aren't broken and/or were done for reason.

2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0.

3) Cosmetic reording of some code (tested) that makes the defintion
   more clear.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
b6c8bc0981 ar71xx: cr3000: Use correct company name
It's 'PowerCloud Systems' not 'PowerCloud'.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
e38520cd50 ar71xx: cr3000: Drop support for defunct cloud
The CR3000 stock firmware is now irrelevant as it required a now defunct
cloud service.  Therefore only build images that use the entire flash
(overwriting stock firwmare-specific partitions that no longer matter),
previously called 'nocloud' images.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
60cf71ede7 ath79: Forward port support for CR3000
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering.  It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:

1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.

2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.

3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.

4) eth0 is wan and eth1 is lan (switch)

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:53 +02:00
Koen Vandeputte
fec8fe8069 kernel: bump 4.9 to 4.9.116
Refreshed all patches

Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch

Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.

Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9

Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-01 09:46:59 +02:00
Jo-Philipp Wich
d0e0b7049f sdk: bundle usbip userspace sources
Bundle the usbip utility sources shipped with the Linux kernel tree in
order to allow the usbip packages from the package feed to build within
the OpenWrt SDK.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 09:12:17 +02:00
Stijn Tintel
77e3e706ce kernel: add missing ARM64_SSBD symbol
In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for
ARM64. Add this symbol to all ARM64 targets using kernel 4.14.

This mitigates CVE-2018-3639 on ARM64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 12:22:11 +03:00
Daniel Golle
7dcdf16222 kernel: remove duplicate #define's in at803x Ethernet PHY driver
AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.

Fixes: f791fb4af4 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-07-31 05:28:48 +02:00
Daniel Golle
a497e47762 kernel: re-add patch for AT8032 Ethernet PHY
The patch was wrongly removed by a kernel version bump to 4.9.105 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.

Fixes: 7dca1bae82 (kernel: bump to 4.9.105)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-07-31 04:56:58 +02:00
Stijn Tintel
ef025e6417 kernel: add pending e1000e fixes
The previous round of fixes for the 82574 chip cause an issue with
emulated e1000e devices in VMware ESXi 6.5. It also contains changes
that are not strictly necessary. These patches fix the issues introduced
in the previous series, revert the unnecessary changes to avoid
unforeseen fallout, and avoid a case where interrupts can be missed.

The final two patches of this series are already in the kernel, so no
need to include them here.

Patchwork: https://patchwork.ozlabs.org/cover/881776/

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:34 +03:00
Stijn Tintel
22b9f99b87 kernel: bump 4.14 to 4.14.59
Drop patch that was superseded upstream:
ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch

Drop upstreamed patches:
- apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch
- apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch
- ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch
- generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch
- generic/pending/900-gen_stats-fix-netlink-stats-padding.patch

In 4.14.55, a patch was introduced that breaks ext4 images in some
cases. The newly introduced patch
backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
addresses this breakage.

Fixes the following CVEs:
- CVE-2018-10876
- CVE-2018-10877
- CVE-2018-10879
- CVE-2018-10880
- CVE-2018-10881
- CVE-2018-10882
- CVE-2018-10883

Compile-tested: ath79, octeon, x86/64
Runtime-tested: ath79, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:07 +03:00
Matt Merhar
a2eaaaaf4b kernel: switch compatible property for RedBoot DT binding
This changes the DT binding's compatible property to
"ecoscentric,redboot-fis-partitions", removing the existing reference to
Red Hat.

Per the documentation hosted at eCosCentric's website, eCosCentric is
RedBoot's sole commercial maintainer since 2002, and the project has
been under the stewardship of the Free Software Foundation since 2008.

This also updates the property in the Inventel Livebox 1 .dts, the
binding's only current user.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-07-30 23:49:49 +02:00
John Crispin
5f5d812881 brcm2708: fix w1 patch
this is now part of generic

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-30 20:51:56 +02:00
Sven Eckelmann
e3b8ae2b09 ipq40xx: Limit usable channels for OpenMesh A62 PHYs
The OpenMesh A62 is a tri-band device (1x 2.4GHz, 2x 5GHz) with special
filters in front of the RX+TX paths to the 5GHz PHYs. These filtered
channel can in theory still be used by the hardware but the signal strength
is reduced so much that it makes no sense.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-07-30 20:46:13 +02:00
Matt Merhar
af3b1756f0 ath79: fix irq assignment for pci-ar71xx driver
In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.

The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.

While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-07-30 20:22:44 +02:00
Thibaut VARÈNE
c6ee683d64 ar71xx: define switch for rb-952ui-5ac2nd
QCA9533 built-in switch can be configured

Tested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 18:14:30 +02:00
Mantas Pucka
3dd692cd6b ipq40xx: fix booting secondary CPU cores
95672e04 broke booting secondary cores by removing 'qcom,saw' property
from L2 cache node. kpssv2_release_secondary() requires it.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2018-07-30 17:55:04 +02:00
John Crispin
eddf4eae97 ar71xx: fix TL-WR1043N v5 port mapping
fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.")

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-30 17:47:06 +02:00