- Duckbill uses a different partitioning approach than standard
FSL and Olimex
- use new sdimage to integrate U-Boot into the SD card images
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47021
- fix Kernel dts subdir location
- enable virtio networking
we are using -M virt which supports virtio devices
changes in symbols due to make kernel_oldconfig:
- CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y : removed
fix security: upstream id: d1fd836dcf00d2028c700c7e44d2c23404062c90
- CONFIG_ARM64_CPU_SUSPEND: removed
commit id: af3cfdbf56b91785650f54e7c9a899d814b4b9fb
- CONFIG_ARM64_PGTABLE_LEVELS=3 : renamed PGTABLE_LEVELS
commit id: 9f25e6ad58e1fb3b4d441e4c55635c4598a6fa94
- CONFIG_GENERIC_CLOCKEVENTS_BUILD=y : removed upstream
commit id: 9f083b74df3a7eaa100b456f2dc195512daf728e
-# CONFIG_PREEMPT_RCU: unnecessary
unknown remove reasons:
-CONFIG_GENERIC_IOMAP=y
-# CONFIG_POWER_RESET_GPIO is not set
-# CONFIG_POWER_RESET_GPIO_RESTART is not set
-# CONFIG_POWER_RESET_LTC2952 is not set
-# CONFIG_POWER_RESET_SYSCON is not set
-# CONFIG_XEN is not set
tested and boot, networking work with qemu
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47005
QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different
is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they
have the same device ID(0x1150). So they share the same codes.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
SVN-Revision: 46971
the lantiq dsl hack to struct atm_trafprm broke the ABI fix this by moving
the variables to the end of the struct
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46964
The pinctrl-rt2880 code doesn't support multiple functions with the same
name. This will result in a incorrect pinmux configuration.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46963
This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro.
Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com>
SVN-Revision: 46961
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
This follows ar71xx, lantiq and partially bcm53xx.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46945
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
This follows ar71xx, lantiq and partially bcm53xx.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46944
As explained in recent sysupgrade/nand.sh commits, current NAND
sysupgrade is a bit misleading because of nand_do_platform_check
behavior. It leaves a special mark in /tmp/sysupgrade-nand-path
triggering some diffent code path in nand_upgrade_stage1.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
Please note that because of current nand_upgrade_stage1 implementation
this patch doesn't change any behaior yet. It only prepares lantiq
target for changing nand_do_platform_check (it will be possible after
preparing all other targets as well).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46939
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
The GPIO pins for "POE passthrough" of Ubiquiti Nanostation models are the
following:
* Ubiquiti Nanostation M XM: Pin 8
* Ubiquiti Nanostation M XW: Pin 2
The previous definition of the pins was mixed up between XM and XW model.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46922
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
Add AR9 DTS definition to be recognized by the DWC2 driver.
The same driver parameters can be mostly used except that some boards
seem to erroneously report OTG HNP/SRP capability of the USB HCD.
Forcing the HNP/SRP off allows these boards to work with the DWC2 as well.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46915
Since the AR9 USB is very similar to the VR9 USB it too can be used with
the upstream DWC2 driver.
Here are the DTS definitions which make it compatible with the DWC2
driver.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46914
Based on the ltq-hcd driver the AR9 USB can be initialized the same way
as the VR9 platform. Use the same initialization bits for both
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46913
Force opkg to store the downloaded repository indizes into the cache
directory as well, this way the IB can be used in an offline setting
once all required files have been cached.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46912
To make the lzma-loader build with binutils 2.25.1 it is needed to
remove the .MIPS.abiflags section otherwise I get the following compile
error:
mips-openwrt-linux-musl-objcopy -O binary -R .reginfo -R .note -R .comment -R .mdebug -S loader loader.bin
mips-openwrt-linux-musl-objcopy: Warning: Writing section `.text' to huge (ie negative) file offset 0xffffffff80a00000.
mips-openwrt-linux-musl-objcopy:loader.bin[.text]: File truncated
This should close#20487.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46893
This moves arch patches affecting many DTS files. Thanks to this change
we can put some ready-to-mainline patches at 300-319 and simplify
backporting process.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46889
As requested here #20432 I've
tried to fix the missing symbols from the specified default kernel
config files.
I ran into this problem trying to build an image for x86_64 target
with a custom kernel configuration.
Signed-off-by: Manganini Mirko <mmanganini@gmail.com>
SVN-Revision: 46879
the trx utile uses a maximum image size of 7.2MB. There are brcm47xx
devices even with serial flash with bigger flash chips, but OpenWrt was
not able to create images for these devices. This patch provides an
additional parameter which increases this limit to 32 MB. There is a
warning in the trx utile code which suggests that bigger images could
overwrite the nvram partition on some devices, but normally the program
writing the image should make sure that it is safe to write it to the
flash.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46872
This patch changes nothing on the behaviour, it just breaks long lines
with bin/trx to make it easier to add additional parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46871
Fixes support for AR9287 on TP-Link TD-W8980 and possibly other devices
which have an ath wifi chip at a PCI address other than 0xb8000000
(TD-W8980 for example has it's wifi chip at 0xbc000000).
Signed-off-by: Geoffrey McRae <geoff@spacevs.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46869
The previous "link" and "status" functions were non-standard,
and thus less useful for parsing.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 46864
Increase space for kernel and also introduce a 8M flash target into the
Makefile.
Signed-off-by: Attila Lendvai <attila@lendvai.name>
SVN-Revision: 46862
The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The
PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself
will not be build because CONFIG_RTC_CLASS is currently not enabled for its
kernel.
Enabling this option should fix the problem of the missing rtc device on
these boards.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46857
According to the AR7242 datasheet section 2.8, AR724X CPUs use a 40MHz
input clock as the REF_CLK instead of 5MHz.
The correct CPU PLL calculation procedure is as follows:
CPU_PLL = (DIV * REF_CLK) / REF_DIV / 2.
This patch is compatible with the current calculation procedure with default
DIV and REF_DIV values.
Test on both AR7240, AR7241 and AR7242.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46856
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
In krait_cpufreq_probe, both freq and max_cpu_freq are never
initialized, so the max_cpu_freq will have a random value at the end.
Fix this by properly initializing max_cpu_freq to 0 and storing the clk
frequency in freq as well, to make it similar to how it's calculated in
krait_set_target.
Fixes the following warnings:
In file included from include/linux/clk.h:16:0,
from drivers/cpufreq/cpufreq-krait.c:13:
drivers/cpufreq/cpufreq-krait.c: In function 'krait_cpufreq_probe':
include/linux/kernel.h:714:24: warning: 'freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
_max1 > _max2 ? _max1 : _max2; })
^
drivers/cpufreq/cpufreq-krait.c:217:25: note: 'freq' was declared here
unsigned long freq_Hz, freq, max_cpu_freq;
^
In file included from include/linux/clk.h:16:0,
from drivers/cpufreq/cpufreq-krait.c:13:
include/linux/kernel.h:714:24: warning: 'max_cpu_freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
_max1 > _max2 ? _max1 : _max2; })
^
drivers/cpufreq/cpufreq-krait.c:217:31: note: 'max_cpu_freq' was declared here
unsigned long freq_Hz, freq, max_cpu_freq;
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46839
The phy driver has its qcom-dwc3 order switched in contrast to the usb
controller driver.
Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46838
commit r30917 ("kernel: bypass all netfilter hooks if the sysctls for that
functionality have been disabled - eliminates the overhead of enabling
CONFIG_BRIDGE_NETFILTER in the kernel config") introduced an optimization
which should reduce/eliminate the overhead for traffic send over bridges on
kernels compiled with CONFIG_BRIDGE_NETFILTER=y. But this optimization
breaks the nf_call_iptables per bridge setting which is more fine grained
than the global sysctl net.bridge.bridge-nf-call-iptables setting.
A test reflecting a real world setup was created to identify if this really
eliminates the overhead and if per-bridge nf_call_iptables could be used in
some setups to increase the throughput. A Qualcomm Atheros QCA9558 based
system with one ethernet and an ath9k wifi 3x3 in HT40 mode was used.
Cables from the AP to the wifi station were used to reduce interference
problems during the tests.
The wlan interface was put in one bridge interface called br-wlan. This
bridge usually contains some more wlan interfaces. The eth0 was put in a
second bridge called br-lan. This usually contains some other privileged
wlan or mesh interfaces. Routing was added between br-lan and br-wlan.
Three kernels were tested:
* (default) OpenWrt kernel for this device
* (brfilter-global) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y
* (brfilter-local) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y and
without 644-bridge_optimize_netfilter_hooks.patch
The changes to the the netfilter settings of the bridge were done via:
* (brfilter-global) /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=1
* (brfilter-lobal) echo 1 > /sys/class/net/br-lan/bridge/nf_call_iptables
and/or echo 1 > /sys/class/net/br-wan/bridge/nf_call_iptables
A station connected to the wlan0 (AP) interface was used to send traffic to
a PC connected via ethernet. iperf with 3 concurrent transmissions was used
to generate the traffic.
| kernel | br-nf-* global | nf-call* iface | download | upload |
|-----------------|----------------|----------------|----------|----------|
| default | 0 | - | 209 | 268 |
| brfilter-global | 0 | - | 185 | 243 |
| brfilter-local | 0 | - | 187 | 243 |
| brfilter-local | 0 | br-lan | 157 | 226 |
| brfilter-local | 0 | br-lan br-wlan | 139 | 161 |
| brfilter-global | 1 | - | 136 | 162 |
Download/upload results in Mibit/s
It can be seen that the patch doesn't eliminate the overhead. It can also
be seen that the throughput of brfilter-global and brfilter-local with
disabled filtering is the roughly the same. Also the throughput for
brfilter-global and brfilter-local for enabled filtering on all bridges is
roughly the same.
But also the brfilter-local throughput is higher when only br-lan requires
the filtering. This setting would not be possible with
644-bridge_optimize_netfilter_hooks.patch applied and thus can only be
compared with brfilter-global and filtering enabled for all interfaces.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46835
It was corrupted in r38528. The most obvious symptom is repeated messages like this:
Tue Sep 8 08:25:18 2015 kern.warn kernel: [77141.972226] br-lan: received packet on wlan0 with own address as source address
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 46821
Everything except for blkcipher was already built-in, so make blkcipher
built-in as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46820
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.
Known issues:
* 5 GHz wifi not working - there is no quantenna driver
* One of the USB ports is not working
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46796
To use gpio leds as ide leds, we need to enable the trigger to be
included in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46795
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46789
Currently, multicast packets from an STA are sent to any according
multicast listener directly through the bridge multicast-to-unicast
feature. Unfortunately, so far this includes the originating STA, too,
resulting in multicast packets being echo'ed back to the originating STA
if it itself is a multicast listener for that group.
This behaviour breaks IPv6 duplicate address detection: An IPv6 Neighbor
Solicitation for IPv6 Duplicate Address Detection is being echo'ed back,
resulting in the host falsely detecting an address collision, which
makes the node unable to claim an IPv6 address and use IPv6 in general.
Mac80211 unfortunately only prevents the echoes for us for multicast
frames. For the multicast frames cast to a unicast destination we'll
need to take care of excluding the originator ourselves.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 46765
Support for lantiq_svip_be has been removed a while ago, so EASY33016
images weren't buildable anymore. Remove the recipes as well as gzip
compressed kernel support, as EASY33016 was the last user of it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46760
We register all gpio buttons and leds through DT, so no need to keep
fixes/additions for the platform data based bay.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46753
Add support for Comtrend VR-3026e v1.
The device is almost identical to the Comtrend VR-3025un.
Signed-off-by: Martin Tesar <tesarmar@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46752
/etc/uci-defaults/02_network had a typo, making it generate the wrong
network config.
Closes#20407.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46727
Add an upstream fix for /proc/net/route causing missing routes doing
several continued reads from it.
Only 4.1+ is affected.
Closes#20403.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46726
should improve flash access times. Should be harmless to gnerally
enable regardless if a flash supporting dual reads is attached. In
doubt, spi-nor will just fall back to serial reads.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46725
A call to pskb_may_pull() might reallocate skb->data. Therefore we
should only assign the src-pointer after any potential reallocations.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46721
This reverts commit a080e8e1943156168913d0353a2e99d1151102aa.
It did not fix the problem but just hid some symptom. The real issue was
that IGMP/MLD report suppression was not considered for the
multicast-to-unicast feature. A recent netifd which isolates IGMP/MLD
reports between STAs by utilizing AP-isolation and bridge-hairpinning
should have fixed this.
It is perfectly fine to apply multicast-to-unicast to IPv6 Neighbor
Solicitations, too (once that feature is configured correctly).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46720
Remove 131-MIPS-export-get_c0_perfcount_int.patch which was already applied
in 4.1.6. This fixes the following build error:
arch/mips/ath79/setup.c:217:77: error: redefinition of '__kstrtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:77: note: previous definition of '__kstrtab_get_c0_perfcount_int' was here
arch/mips/ath79/setup.c:217:350: error: redefinition of '__ksymtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:350: note: previous definition of '__ksymtab_get_c0_perfcount_int' was here
scripts/Makefile.build:258: recipe for target 'arch/mips/ath79/setup.o' failed
Reported-by: swalker
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46715
Properly treat -ENOSYS as no PHY, else ehci-orion won't work without
generic phy support.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46711
Some CFEs seem to misconfigure the mapped memory flash access with
fast read but without a dummy byte, causing all accesses to be prefixed
with 0xff.
This of course breaks reading out the nvram, so do not just move back to
single i/o accessors, but also ensure that the dummy byte is correctly
set.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46707
Now that the switch driver can handle two devices with
the same MAC address in separate VLANs we can go back
to using the same address on both interfaces.
This is the Linksys firmware's default behavior.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46700
This also clears any bootloader-set FDB defaults. This had
caused issues creating port-based VLANs when mappings
overlapped previous VLANs. Packets destined to a port
not in the default port group flooded all ports.
Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC)
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46699
The u-boot boot counter was never reset after a successful boot,
which sometimes could make some variables become out of sync.
This patch adds support for the boot counter and enables
auto_recovery unconditionally.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46690
The patch submitted in [46649] was mangled in the use of gmails webmail interface, tabs replaced with spaces, resulting in a patch which dit not apply.
This should fix the issue, sorry for the noise.
Signed-off-by: Ben Whitten <benwhitten@gmail.com>
SVN-Revision: 46676
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46672
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46671
The BT Home Hub 5A uses three PEF7071 with PHY ID 0xd565a401. Daniel's
PHY driver (for his u-boot sources) already supports that PHY because
it uses a PHY ID mask of 0xfffffff8.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46670
Instead of using board name provided explicitly as text in LED name, ex.:
[...]
mlwg2)
status_led="mlwg2:blue:system"
[...]
use $board variable, which allows to combine together multiple boards with same color and LED names, ex:
[...]
mlw221|\
mlwg2)
status_led="$board:blue:system"
[...]
The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically.
One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46665
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
* fixes wrong indentation
* keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
* fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
* combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46664
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds flash layout parser for TP-Link firmwares which have a 64kb
bootloader.
This is used for TP-Link TL-WDR6500 v2.
SVN-Revision: 46662
*Enable SMEM MTD parser and its dependencies (SMEM & HW spinlocks) in
the kernel config
*Replaces the MTD layout in DT by the dynamic layout provided by the
SMEM parser for AP148
Using the OF based parser is still possible on platforms which have a
fixed MTD partition layout.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46658
This patch adds a new parser which uses the SMEM available on IPQ and
some other QCOM platforms to map the MTD partitions.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46657
2 patches are cherry-picked from the following LKML thread:
*https://lkml.org/lkml/2015/4/11/208
The last patch (036-soc-qcom-add-smem-to-IPQ806x-platforms.patch) is
adding the corresponding DT nodes required for IPQ806x.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46656
This change cherry-picks the following 3 changes from linux-next:
*fb7737 hwspinlock/core: add device tree support
*19a0f6 hwspinlock: qcom: Add support for Qualcomm HW Mutex block
*bd5717 hwspinlock: qcom: Correct msb in regmap_field
We're also adding a patch to add the hardware spinlock device nodes on
IPQ806x platforms (033-soc-qcom-Add-sfbp-device-to-IPQ806x-dts.patch).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46655
The "linux,part-probe" dts parsing is a pretty neat generic feature.
It has been posted to kernel.org and could easily be reused by all
targets.
This change moves the patch to the 3.18 and 4.1 generic folders, and
makes the feature available to all platforms who may want to use it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46654
This patch is backport of a fix to a USB prototype mismatch bug found
in 3.18 kernels, originally submitted by Boris Brezillon [1].
The symptom of this bug was that devices attached to the at91 using
at91_ohci on a hub never appeared and failed to initialise.
[1] http://www.spinics.net/lists/linux-usb/msg125969.html
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
SVN-Revision: 46649
to avoid editing the dts every time the kernel size changes.
uImage is now bigger than 1MB. Pad uImage to 64k erase block size.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46648
Switch to generich chip irqs/irq domains.
Interrupts were broken since kernel 3.14. dLAN USB extender is now
booting again.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46647
Switch to new 8250 debug uart code because the old
mach-mcs814x/include/mach/debug-macro.S tries to include
asm/hardware/debug-8250.S which no longer exists since kernel 3.14
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46646
The MT7621 uses a 2 bit wide configuration of the sdhci, spi, mdio, pcie,
wdt, uart2 and uart3 in the GPIO_MODE register. It was correctly done
for sdhci, spi, pcie and wdt, The same has to be done for uart3, uart2
and mdio.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46645
The PINS conntrolled by the SPI bits in the GPIO_MODE register is always
7 and not 8 for nand mode.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46644
The uart3 setting in GPIO_MODE register is before the uart2 setting. Also
don't mix uart2 and uart3 function/groups.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46643
The following patch:
* fixes wrong indentation
* combines together boards with same configuration
* removes unnecessary spaces
* removes empty lines after ";;" and uses only "|\" (for consistency)
* orders boards alphabetically
in base-files/etc/board.d/02_network script.
One bug was left untouched: freestation5 board is listed twice in case statement, in ramips_setup_macs().
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46634
This patch:
* fixes various mistakes (leading spaces, wrong or missing model names)
* shortens model strings (we don't need to use whole model string from dts file, make it for consistency and as optimization)
* sorts boards alphabetically
in base-files/lib/ramips.sh script.
Case statement was tested after above changes with simple script, which:
* takes model string from dts{,i} file (model = "...")
* provides this value as case input ($machine)
* returns output ($name)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46632
This patch:
* fixes wrong indentation
* fixes wrong names and descriptions (ex. Dlink -> D-Link)
* changes filenames to manufacturer names
* moves oem/unknown manufacturers boards to misc.mk profiles
* combines profiles for boards from the same manufacturers in one file (ex. Olimex)
* fix profile files structure (keep the same convention as in other targets, ex. ar71xx)
in various .mk profiles, in ramips target.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46631
It seems that support for Edimax BR-6524N was dropped long time ago (dts file for this device is missing).
This patch removes remaining code.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46630
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46629
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46628
The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46624
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
* changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
* changes filenames of dts and profile files
* changes image filenames
for Olimex RT5350F-OLinuXino{,-EVB} devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46623
The following patch changes:
* board name from "wl341v3" to "wl-341v3"
* dts filename
* LED names in dts file
for Sitecom WL-341v3 device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46622
The following patch:
* changes board name from "argus-atp52b" to "atp-52b"
* changes dts filename
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Argus ATP-52B device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46621
This patch removes manufacturer from Belkin F7C027 image name ("belkinf7c027" -> "f7c027").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46620
Other Asus RT-N dts files are named "RT-N..." (not "RTN..."), so use the same for RT-N56U.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46619
The following patch:
* changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
* changes filenames of dts and profile
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Xiaomi MiWiFi Mini device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46617
This patch:
* fixes typo (rp_n53 -> rp-n53) in Asus RP-N53 image name
* removes manufacturer from image names for Lenovo Y1{,S} devices
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46616
There are other Asus boards supported in ramips target, so use the same naming scheme for WL-330N{,3G} boards and their dts files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46615
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46614
The following patch fixes:
* wrong indentations
* doubled gpio-keys-polled nodes (DIR-300-B7, DIR-320-B1, DIR-610-A1)
* duplicate spacings
* empty lines at end of files and after last child nodes
* trailing and leading whitespace
* unnecessary and commented-out code
* missing empty lines between nodes and between properties and nodes
* unnecessary empty lines between nodes properties [1]
in .dts{,i} files, for ramips target.
[1] Some of empty lines in SOCs dtsi files were left untouched, because they seem to be there for a reason (readability?).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46613
In addition to the update this also fixes compile problems with kernel 4.1.
This closes#20323.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46609
It's nice to have a distinction between files which are built during the
normal OpenWrt build process and ones that are created by the ImageBuilder
(like it already exists on some other targets).
This also gives boot.img a profile-specific prefix as it contains profile-
specific data.
KDIR_TMP does not need to be specified since include/image.mk already sets
it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 46607
Install uboot files to KERNEL_BUILD_DIR instead of BIN_DIR to fix
ImageBuilder. Similar fixes are necessary for many (all?) other uboot
targets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46605
The DTS files aren't useful (other targets don't copy them either) and
clutter BIN_DIR with files unrelated to the chosen profile.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46604
Switch ipq806x to the new image build system. Image files might change
slightly their names, but the generated files should not change.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46602
Linux 4.1 is also affected from the dma issue, so remove the dma
proprties there as well.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46599
Make the device name accessible for any build commands instead of
forcing targets to define it themselves.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46597
Instead of letting each target define it themselves, create on in
include/image.mk and let the targets use it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46596
Instead of each target defining it the same, move the KDIR_TMP
definition to include/image.mk. In addition Image/Build/SysupgradeNAND
already requires KDIR_TMP to be set, so it makes sense to have it
globally defined.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46592
Previous patch 6f2905eeb6ce5ddec8d12d677e1f377a940b537b enabled ADM in
the kernel, which causes a kernel panic when accessing the SPI flash.
As a workaround, We'll disable DMA for the flash for now. It was not
enabled previously anyway so we'll just leave it as is.
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46587
We got check for nvram_len placed too early and the code never tried
reading CFE variables used on WGT634U. This is a regression introduced
in r45942 and reported in #20291.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46584
Previous patch set backported the recently posted NAND flash driver to
3.18 and 4.1 kernel. This patch now enables it in the kernel config.
There is no change to the partition layout and init yet. But the NAND
flash can be seen in the mtd list on an AP148:
root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 10000000 00020000 "qcom-nandc"
...
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46569
These patches add support for ipq806x NAND flash controller. Most of
these are cherry-picked & backported from LKML:
*https://lkml.org/lkml/2015/8/3/16
This patch just modifies the kernel code, but doesn't change the config.
It should be harmless.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46568
These are cherry-picked & backported from LKML:
*https://lkml.org/lkml/2015/3/17/19
They are enabled on both 3.18 and 4.1 kernel. Patches 150 to 154 are
applying changes merged since 3.18; they enable mechanisms used by the
ADM driver.
ADM engine is used by the NAND controller, so it is necessary to
bring-up NAND flash support.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46567
Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used
for template generation, so need to be present before inclusion of
image.mk in target image Makefiles.
So move all declarations to before any includes.
Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46564
It looks like RAC flushes cause random corruption(?) when the
second thread is set as default.
Fixes#20160.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46563
BCM6318: add support for Plusnet / Sagem 2704N (V1)
Signed-off-by: Matt Goring <matt.goring@googlemail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46562
We forgot to enable the stmmac driver for 4.1 kernel, so ethernet
interfaces don't show-up on this kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46559
Old bootloader (same ones which have DT disabled) don't perform any PCIe
initialization. The consequence is a freeze during PCIe bring-up on
these old u-boot. Same kernel with a newer bootloaders works fine as
they contain the corresponding PCIe init code.
In this change, we'll add the missing init and make sure the kernel
doesn't rely on some preexisting init to get PCIe to work. That includes
the following changes:
*GPIOs: set function & drive strength
*Clocks: add init code for aux & ref clocks
*PCIe driver: additional init of the hardware controller
Tested 3.18 and 4.1 on an AP148 with bootloader branch 0.0.1
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46557
PCIe controller nodes are numbers 0/1/2 in the chipset dtsi file, but
the pinmux nodes are numbers 1/2/3. We'll make it consistent by changing
the pinmux numbering to match the controller's one.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46556
Certain AP148 platforms (and derivative) use bootloaders which did not
have DT enabled.
In order to support these old platforms, we'll now make the following
modifications:
*explicitely add the memory node in the AP148 DT: this used to be added
by new u-boot through a run-time patch mechanism. We'll now add it
explicitely so it works on boots which don't support that feature. New
boots will have the node twice, the second one will be ignored.
*add the zImage generation next to the FIT image for AP148.
Other platforms using non-DT enabled bootloaders may want to leverage
this zImage code to generate their own firmare as well.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46555
The generic kernel cmdline parser ignores argv[0], this caused a
regression for all lzma-loader based boards with linux 4.1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46544
Fix for default button states in WRT1900AC dts files.
This prevents overlay wipe when reset is pressed.
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
SVN-Revision: 46530
Extend the SDK Config.in file to explicitely declare a MODULES symbol with
the "option modules" flag set in order to prevent a kconfig segmentation fault
whenever a "depends m" dependency is encountered.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46514
