Commit graph

2158 commits

Author SHA1 Message Date
Enrico Mioso
acd8649b18 ramips: let the "reserved" MTD partition be RO for R6220
The "reserved" partition should probably be read-only, just in case. Even
not knowing it's content, other devices have marked it as such, so it
seems a good idea to do so also for this device.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Mathias Kresin <dev@kresin.me>
CC: Hanqing Wong <hquu@outlook.com>
2017-05-31 08:45:02 +02:00
Matthias Schiffer
9ab81e63cd
ramips: sysupgrade: move nand_do_upgrade call to platform_do_upgrade
All targets with NAND support should gradually move their nand_do_upgrade
calls from platform_pre_upgrade to platform_do_upgrade.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-05-29 23:50:33 +02:00
Filip Moc
43e4e1f4a5 Move enablemodem from ramips to new package adb-enablemodem and make it used also by TL-MR6400
Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:40 +02:00
Russell Senior
b76248dd96 ramips: remove fictional LEDs from AsiaRF AWM00x device tree
Neither the AsiaRF AWM002 or AWM003 actually has an LED on the module
board.  The ld1 and ld2 do not represent actual LEDs.  These pins might
connect to LEDS on an eval board or other carrier board, but that is
outside the scope of this device tree file.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2017-05-27 07:01:39 +02:00
Hauke Mehrtens
0b17375931 kernel: update kernel 4.9 to 4.9.30
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-27 00:48:37 +02:00
Kyson Lok
abbfcc8525 ramips: add support for GL-inet GL-MT300N-V2
This patch adds supports for the GL-inet GL-MT300N-V2.

Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)

Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00
Giuseppe Lippolis
4ba2f4dc63 DWR-512: adding wwan support for the dwr-512 3G modem
This PR allow the 3G modem embedded in the DWR-512 to be managed
by the wwan-ncm scripts. The modem will use the usb-option and
usb-cdc-ether drivers.
The DWR-512 DT is updated accordingly.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-05-25 19:01:08 +02:00
Koen Vandeputte
e842e16f45 kernel: update kernel 4.9 to 4.9.29
- Refresh all patches
- Removed upstreamed
- Adapted 1

Compile tested on: bcm53xx, cns3xxx, imx6, lantiq
Run tested on: cns3xxx & imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[update from 4.9.28 to 4.9.29]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-21 21:51:22 +02:00
Kevin Darbyshire-Bryant
088e28772c kernel: update kernel 4.4 to version 4.4.69
Refresh patches. A number of patches have landed upstream & hence are no
longer required locally:

062-[1-6]-MIPS-* series
042-0004-mtd-bcm47xxpart-fix-parsing-first-block

Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup
as it was incorrectly included upstream thus dropped from LEDE.
As it has now been reverted upstream it needs to be included again for
LEDE.

Run tested ar71xx Archer C7 v2 and lantiq.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[update from 4.4.68 to 4.4.69]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-21 21:48:16 +02:00
Michael Lee
eee09bfe01 ramips: support jumbo frame on mt7621 up to 2k
Signed-off-by: Michael Lee <igvtee@gmail.com>
2017-05-18 14:50:16 +02:00
Steffen Weinreich
e71b2dad94 ramips: add om-watchdog to rut5xx DEVICE_PACKAGES
Add om-watchdog as default package for rut5xx.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
2017-05-15 22:43:33 +02:00
Jo-Philipp Wich
8451b06023 ramips: fixup-mac-address: add missing include
Add missing include of ramips.sh in order to import the missing
ramips_board_name() procedure.

Fixes FS#774.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-05-11 00:52:03 +02:00
Ørjan Malde
5f932988c3 ramips: add support for Asus RT-AC51U
Specification:
 - SoC: MediaTek MT7620A (580 MHz)
 - RAM: 64 MiB (Winbond W9751G6JB-25)
 - Flash: 16 MiB (Spansion S25FL128SAIF00)
 - LAN: x4 100M
 - WAN: x1 100M
 - Others: USB 2.0, reset button, wps button and 9 LEDs

Issues:
 - 5 GHz band is not functional (missing driver support)

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75;
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the sysupgrade
   image, and press upload

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
 tftp> quit

Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
2017-05-10 08:45:12 +02:00
Alexey Belyaev
a7cbf59e0e ramips: add new device ZyXEL Keenetic as kn
This device exactly same as NBG-419N but with USB port and USB Led.

Specification:

- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0

Installation via serial console (57600 8N1) from TFTP server
 - rename the firmware to something shorter, for example
   "sysupgrade.bin" (max. 32 chars)
 - copy firmware TFTP server's directory
 - when you power on device, and see U-Boot log, immediatly push "2"
   once.
 - You will see this message:
     2: System Load Linux Kernel then write to Flash via TFTP.
        Warning!! Erase Linux in Flash then burn new one. Are you sure?
 - Push "y", and enter: device IP, then TFTP server's IP, and then
   image firmware file name.

The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).

Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-10 08:45:12 +02:00
Sven Roederer
4c3953ba29 ramips: use GPIO_ACTIVE macros in UBNT-ERX.dts
- reorder includes
- use GPIO_ACTIVE_LOW macro instead of hardcoded "1"

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-05-06 09:49:00 +02:00
Henryk Heisig
64f2efcdff ramips: strip padding from TP-Link sysupgrade images
This reduce size of sysupgrade firmware.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-05-05 20:02:19 +02:00
Henryk Heisig
cfdd3f260e ramips: add factory firmware for Tp-Link C20i/C50
TP-Link firmware doesn't accept sysupgrade.bin with metadata.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-05-05 20:01:28 +02:00
Daniel Golle
d17cb4a68a ramips: purge default packages on MT7621
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.

Hopefully fixes FS#758

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-05-04 14:13:23 +02:00
Paul Spooren
414b65db85 ramips: enable ramdisk for mt7621
Fixes #758

Signed-off-by: Paul Spooren <paul@spooren.de>
2017-05-04 00:51:05 +02:00
Jo-Philipp Wich
a45cde9118 ramips: ZTE-Q7: fix switch driver initialization in DTS (FS#716)
Add the changes suggested by FS#716 to fix the switch driver initialization
on the ZTE Q7.

Also remove the `pinctrl-names` field obsoleted by the changes.

Reported-by: Harry Lau <harrylwc@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-04-27 10:44:28 +02:00
Mathias Kresin
3a2cc2c8ad ramips: fix syntax error in board.d/01_leds
Fixes the following error:

  syntax error: unexpected newline (expecting ")")

Fixes: FS#739

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-27 09:39:34 +02:00
Mathias Kresin
bd2727fb25 ramips: ZBT-WE826: include the correct dtsi
Fix a copy/paste error and include the ZBT-WE826 dtsi instead of the
ZBT-WG3526 one.

Fix the syntax error in the ZBT-WE826 dtsi to prevent an compile error.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-27 09:39:34 +02:00
Mathias Kresin
725238f698 ramips: use the ZBT-WE826 power LED for status indication
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
2ddaf96a77 ramips: add ZBT-WE826 32MB variant
The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
3cfc909c54 ramips: rename Digineo AC1200 Pro to ZBT-WG3526 32MB
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
619d68bfc9 ramips: prepare ZBT-WG3526 for hardware variants
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Jiawei Wang
ff258effd5 ramips: add support for ZBT-WE1326
Specification:
- SoC: MT7621AT, MT7603EN and MT7612EN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 512 MiB (EM6GE16EWXD-12H)
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Others: USB 2.0, micro SD slot, reset button and 8 x LEDs

Issues:
- Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs.
- The pwr LED is not GPIO controllable

How to install:
- The original firmware is OpenWrt, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
2017-04-25 19:29:59 +02:00
Alexey Belyaev
187624f759 ramips: fix ZyXEL Keenetic Omni/Omni II GPIOs
Each GPIO bank has only 24 gpios. Use and enable the correct banks for
GPIOs > 24.

Signed-off-by: Alexey Belyaev <spider@spider.vc>
2017-04-25 19:29:59 +02:00
Alexey Belyaev
3549bad814 ramips: fix ZyXEL Keenetic Omni switch config
The wan port is connected to switch port 0. Fix the mediatek,portmap as
well as the default switch config.

Signed-off-by: Alexey Belyaev <spider@spider.vc>
2017-04-25 19:29:59 +02:00
Matthias Schiffer
411c1b64f0
ramips: update DEVICE_PACKAGES for Ubiquiti EdgeRouter X
Fixes removal of unneeded kernel modules with per-device rootfs.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-04-22 18:55:22 +02:00
Daniel Golle
f66e7cb30b ramips: add former board names to PSG1218 variants
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 14:52:46 +02:00
Mathias Kresin
18618695ae ramips: dont replace the board name
Use fixed led names and add each board variant instead of manipulating
the board name.

It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-21 07:47:59 +02:00
Mathias Kresin
9e468f7829 ramips: add former used board names to metadata
We need to keep the former used (unmodified) boardname in the metadata.
Otherwise an upgrade from an board using the old boardname will be
refused.

Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-21 07:47:59 +02:00
Daniel Golle
c6fe325587 ramips: rename PSG1218 to match label
Fix previous commit to be less ambigous:
PSG1218 rev.A = 5 ports, external PA, heatsinks
PSG1218 rev.B = 4 ports, internal PA, no heatsinks

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 02:55:36 +02:00
Daniel Golle
c5a7dc49d1 ramips: split Phicomm PSG1218 and PSG1218K2C
PSG1218 got only 4 Ethernet ports and WAN on port 3 while
PSG1218K2C got 5 Ethernet ports and WAN on port 4
Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while
at it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 02:29:21 +02:00
Jo-Philipp Wich
aefa195749 kernel: update kernel 4.4 to 4.4.61
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-04-15 18:26:41 +02:00
Mathias Kresin
8322dba029 ramips: really drop the rt-n56u factory image
Remove the stale reference to the factory image.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 19:22:23 +02:00
Mathias Kresin
ae0facdf1d ramips: fix Netgear R6220 package selection
The Netgear R6220 requires the kmod-usb3 package and misses
kmod-usb-ledtrig-usbport package to setup the configured usb led
trigger.

Drop the already target selected kmod-mt76.

Fixes: FS#686

Fixes: 38bee61dab ("ramips: add support for Netgear R6220")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
b4be4617b5 ramips: add RP-N53 pcie wireless eeprom
Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata.
Disable the 2.4GHz band as this band has no antennas attached but is
enabled in the eeprom/caldata.

Fixes: FS#691

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
21abb7492c ramips: fix WHR-600D eeprom dt property
Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as
this board have a RT5592 and uses the rt2x00 driver. The mediathek
device tree bindings do not work here.

Fixes: FS#691

Fixes: d8dd207ea6 ("ramips: use the ralink,mtd-eeprom device tree property")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
1b5ae14162 ramips: drop rt-n56u factory image
The factory image has an uImage header covering the entire image and
not only the kernel. The original uImage header which covers only the
kernel is appended to the end of the image.

During LEDE boot the uImage rootfs splitter skips the whole filesystem,
can't find a valid filesystem magic and panics.

The last known working version was OpenWrt 14.07, which simply kept on
searching for an uImage header if the first found didn't resulted into
a working rootfs. This behaviour is kind of error prone since it could
produce false positives.

Since the sysupgrade image works fine in combination with the tftp
recovery for doing the initial installation of LEDE, simply drop the
factory image.

Related: FS#462

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Hauke Mehrtens
c3778f2647 kernel: update kernel 4.4 to 4.4.59
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-04-02 12:48:00 +02:00
Hauke Mehrtens
b26e34214c kernel: update kernel 4.9 to 4.9.20
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-04-02 12:47:55 +02:00
John Crispin
0f4600c275 ramips: fix pcie irq mapping for mt7621 on v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-28 08:50:13 +02:00
Hauke Mehrtens
fb7ea71c15 kernel: update kernel 4.9 to 4.9.17
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-26 12:23:19 +02:00
Hauke Mehrtens
88b125e9a4 kernel: update kernel 4.4 to 4.4.56
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-26 12:23:12 +02:00
Mathias Kresin
c59469b908 ramips: fix Xiaomi MiWiFi Nano firmware partition size
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.

Fixes: FS#622

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
John Crispin
dce3b0057b ramips: fix mt7621 boot on v4.9
v4.9 CM code has a few bugs on this HW. Disable the GCR register access
during boot. This caused a cpu stall.

Signed-off-by: John Crispin <john@phrozen.org>
2017-03-23 09:18:42 +01:00
Furong Xu
2fd1a3e912 ramips: clean kernel config symbol conflicts for MT7688 PWM
pwm-mediatek should be selected in Other Modules submenu, not default to yes.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-20 08:17:34 +01:00
Vaclav Svoboda
6b9c25e927 ramips: fix switch port mapping for ZBT-WE2026
This patch fixes switch port mapping for Zbtlink ZBT-WE2026.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-20 08:13:56 +01:00
Vaclav Svoboda
815cc2a69a ramips: add support for Zbtlink ZBT-WE2026
This patch adds support for the Zbtlink ZBT-WE2026.

Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M

Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-17 08:58:50 +01:00
Mathias Kresin
11eac705c5 ramips: sort mt7620 image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-12 09:28:19 +01:00
Joseph C. Lehner
de33a4cef0 ramips: add support for Netgear EX3700
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the device's web
interface or via nmrpflash.

Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-12 09:28:19 +01:00
Hanqing Wong
38bee61dab ramips: add support for Netgear R6220
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.

Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
  on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
  (login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
  example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot

nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.

Signed-off-by: Hanqing Wong <hquu@outlook.com>
2017-03-12 09:28:05 +01:00
Kristian Evensen
b11c51916c ramips: Improve Sanlinking D240 config
* The left most mini-PCIe slot (the one attached to SIM2) can be
power-cycled by setting GPIO 0 to high/low.

* The D240 only needs the MT76x2 module, so update makefile to reflect this.
Note that until the default mt7620 target is updated, then kmod-mt76 (and thus
kmod-mt7603) will be selected by default.

v2->v3:
* Indentation error.

v1->v2:
* Rename gpio and remove redundant comment (thanks Piotr Dymacz)

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-03-11 08:36:52 +01:00
Furong Xu
a93a48328d ramips: kmod-sdhci-mt7620: switch dependence to kmod-mmc
mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block.
And, we remove kmod-sdhci dependence assignment from all related target devices.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-11 08:19:37 +01:00
Jo-Philipp Wich
2543e986ad ramips: fix Linksys RE6500 switch port mapping
Properly map the internal switch ports to the proper LAN1..LAN4 labels.

Fixes #530.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-03-07 17:39:20 +01:00
Joseph C. Lehner
11356e4078 ramips: remove kmod-mt76* from EX2700 images
These modules are not needed by the EX2700, since it does not
have an external wifi chip (MT7620A is covered by rt2x00).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-01 22:29:57 +01:00
Furong Xu
b65718ae14 ramips: rename patch file suffix from .c to .patch
Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-01 22:29:57 +01:00
Francois Goudal
9b35815f0f ramips: add support for Afoundry EW-1200
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.

It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.

The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.

Signed-off-by: Francois Goudal <francois@goudal.net>
2017-03-01 22:29:50 +01:00
ZengFei Zhang
edae3479e6 ramips: add support for HiWiFi HC5962
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com

Short specification:

 - MT7621AT + MT7612EN + 7603EN
 - 256MB DDR3 RAM
 - 128MB NAND flash
 - 1+3 x 1000M Ethernet
 - 1x USB 2.0 port. 1x USB 3.0 port.
 - reset button
 - UART pad on PCB (JP3: TX, RX, GND, 3.3V)

Flash instruction:

1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
   $ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
   $ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1

Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
2017-02-28 23:46:02 +01:00
Wang JiaWei
d48cc5e044 ramips: add support for HiWiFi HC5661A
HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.

- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)

The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.

0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"

To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.

sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin

SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.

Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
2017-02-27 11:39:31 +01:00
Joseph C. Lehner
df36b5e1b3 ramips: include only kmod-mt76-core in EX2700 image
This patch frees up flash space on the EX2700, by
removing unused mt76 drivers and firmware.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-02-26 10:26:50 +01:00
Furong Xu
f885edef5a ramips: fix the number of uarts for MT7688
Same as MT7621 and MT7628, MT7688 allows up to 3 uarts

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:09:37 +01:00
Furong Xu
00343e18f2 ramips: fix PWM pin mux conflict in dtsi
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict

[    0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[    0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[    0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0  on device rt2880-pinmux
[    0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back

Keep PWM disabled.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:09:09 +01:00
Hauke Mehrtens
236840eb47 kernel: update kernel 4.9 to version 4.9.10
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-16 00:46:23 +01:00
Daniel Golle
d57223259b ramips: replace remaining instances of ralink, port-map
Some boards were apparently forgotten when ralink,portmap was renamed
to mediatek,portmap -- probably because they used the long obsolete
ralink,port-map attribute.
If this commit breaks ethernet wan/lan assignment, this is because
the port-map attribute wasn't actually parsed, you'll have to replace
"wllll" by "llllw" in the dts file belonging to that board (and send
a patch doing that!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-02-15 09:12:40 +01:00
John Crispin
6cb0372d42 ramips: fix mt7621 ethernet support for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 09:12:00 +01:00
Giuseppe Lippolis
35c60d18c5 ramips: export slic IRQ line in dwr-512
The DWR-512 embeds the hw slic device si3210. This device have the IRQ line
attached to the gpio1. This patch export the gpio1 with proper name and
parameters to the sysfs.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-15 07:45:54 +01:00
Felix Fietkau
f5977c0c0a ramips: revert faulty 4.4 config change from 9c24227090
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-14 13:47:21 +01:00
Furong Xu
a9fdb35740 ramips: Clean duplicated status property for Omega2 WMAC in dtsi
At the tail of dtsi, wmac is enabled twice, clean the first one

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-14 12:19:56 +01:00
Giuseppe Lippolis
85766c8d70 ramips: fixed sms led polarity into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-14 12:19:35 +01:00
Thibaut VARENE
157353c210 ramips: WN3000RPv3: do not setup switch
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-14 12:19:12 +01:00
John Crispin
9c24227090 ramips: add v4.9 support
NAND support is missing

Signed-off-by: John Crispin <john@phrozen.org>
2017-02-14 12:17:52 +01:00
Giuseppe Lippolis
ec0f20212e ramips: added image size into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-13 10:24:32 +01:00
Chuanhong Guo
634328c0de ramips: correct switch configuration for Newifi D1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2017-02-13 10:24:32 +01:00
Claudio Leite
290ca2ba46 ramips: fix AR670W partition alignment
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.

Signed-off-by: Claudio Leite <leitec@gmail.com>
2017-02-09 09:14:45 +01:00
Stijn Tintel
d2c4041f02 kernel: update kernel 4.4 to version 4.4.47
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.

Runtime-tested on ar71xx, octeon, ramips and x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-02-06 03:23:06 +01:00
Kristian Evensen
bb7068f26c ramips: add support for Sanlinking D240
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-02-05 22:23:28 +01:00
Joseph C. Lehner
7d00cfe9bb build: centralize fakeroot code
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.

Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Mathias Kresin
c1eae7a7b8 ramips: fix Airlink AR725W device title
Gemtek is the ODM but the board was sold by Airlink101.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Mathias Kresin
1ba7fa652c ramips: fix Airlink AR725W factory image build
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.

Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Giuseppe Lippolis
f9f636b94e rt5350: added pcm interface in .dtsi
Added the missing audio pcm interface in the .dtsi file for the rt5350
device. The update has been verified from the data get from the datasheet
and is very similar to the mt7620a.dtsi

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-03 05:10:13 +01:00
Mathias Kresin
a0888ecbaf generic: rtl8366rb: fix compatible string
Use a vendor prefix as it has to be for all not core driver. Update the
compatible string in the device tree files accordingly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:46:03 +01:00
Mathias Kresin
2c4d81310f ramips: fix Sercomm NA930 compatible string
The Sercomm NA930 is not a mt7620a evaluation board and shouldn't use
the eval board compatible string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:46:03 +01:00
Mathias Kresin
2281f9929b ramips: remove Planex CS-QR10 sound device tree node
The comptible string is neither added by any LEDE patch nor exists in
in the kernel. Drop the sound node which was obviously added
accidentally with 9195d8da ("ramips: DTS rework").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:45:55 +01:00
Mathias Kresin
05b1fcc70b ramips: cleanup SPI flash device tree properties usage
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.

Remove the linux,modalias property. It is obsolete since kernel 4.4.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-02 22:48:54 +01:00
Tobias Wolf
bf2f09c005 ramips: Introduce CONFIG_MIPS_APPENDED_RAW_DTB to F5D8235 V1 (rt288x)
This activates the CONFIG_MIPS_APPENDED_RAW_DTB kernel configuration and
configures the F5D8235 V1 target to use append-dtb for kernel creation
instead of OWRTDTB.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-02 00:13:49 +01:00
Tobias Wolf
4f86692953 ramips: Introduce CONFIG_MIPS_APPENDED_RAW_DTB to arch/mips/ralink
This commit introduces CONFIG_MIPS_APPENDED_RAW_DTB as an alternative to
OWRTDTB. Both solutions can be used concurrently until all board
configurations have been changed.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-02 00:13:49 +01:00
Felix Fietkau
dabdd123c9 mt76: update to the latest version
Uses upstream code to parse DT supported band/frequency information.
Update existing .dts files to the new format and remove unnecessary
overrides.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 17:49:55 +01:00
Felix Fietkau
2340de62a6 ramips: remove DT pcie nodes for GL-MT300A/N
These devices don't have a secondary wifi chip

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 17:49:54 +01:00
FUKAUMI Naoki
6b0b526a4f ramips: add support for Buffalo WCR-1166DS
Buffalo WCR-1166DS is a small wireless router with

 - MT7628AN + MT7612E
 - 64MiB DDR2 SDRAM
 - 16MiB SPI flash
 - 2T2R 11ac/a/b/g/n Wi-Fi
 - 2x 10/100M ethernet switch
 - 8x programmable LED
 - 3x button
 - UART pad on PCB (J2: 3.3V, GND, TX, RX)

factory image can be installed via stock web UI.

due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-31 11:10:58 +01:00
Felix Fietkau
bc32f7deb5 ramips: add missing DTS pcie node for WSR-600
Enables PCI bus and support for the MT7603 and RT5592 chips

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-31 10:27:38 +01:00
Stijn Segers
20996edd68 Kernel: bump to 4.4.44
Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64.

.44 has been run-tested on the 17.01 branch here on ar71xx and mt7621.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2017-01-27 11:18:27 +01:00
Joseph C. Lehner
f93a121533 ramips: cleanup mt7620 Netgear image code
1. Reuse functions defined in `image-commands.mk`
2. Rename fakeroot image

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-01-27 11:10:10 +01:00
Tobias Wolf
99eb6f97e5 ramips: enable rlt8366s Green Feature for F5D8235 V1
Enable the green feature for the board by default.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2017-01-27 11:10:10 +01:00
Tobias Wolf
d43046e0f6 ramips: add rlt8366s initvals to the F5D8235 V1 DTS
Before this change only port 4 of F5D8235 V1 worked at 1000Mpbs.

Comparing the current driver with the GPL_BELKIN_F5D8235-4_v1000
v1.01.24 sources showed that additional steps are required to set-up
the rlt8366s switch correctly.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2017-01-27 11:10:10 +01:00
Vitaly Chekryzhev
9a53e1bdf9 ramips: ZyXEL Keenetic Omni/Omni2: export gpio usb power
Export gpio usb to allow power management of USB port.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-26 16:39:08 +01:00
Vitaly Chekryzhev
0352cc6b19 ramips: ZyXEL Keenetic Viva: align factory images
ZyXEL web-flasher requires squashfs to be aligned to 64kb.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-26 16:39:08 +01:00
Vitaly Chekryzhev
e8c265b2cc ramips: ZyXEL Keenetic Viva: export gpio usb power
Export gpio usb to allow power management of USB port.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-26 16:39:08 +01:00
Yo Abe
21b4625135 ramips: add ip17xx support to WLI-TX4-AG300N
ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which
should be included by default.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 14:41:31 +01:00
Joseph C. Lehner
0cc04d05f6 ramips: fix EX2700 wireless mac
On some EX2700 devices, the MAC address from the eeprom data differs
from the actual MAC address. Fix that, and cleanup the DTS file
while we're at it.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-01-26 13:53:57 +01:00
Felix Fietkau
bfdc56d3a2 build: remove mips16 feature flag from target makefiles
It can be implicitly derived from the MIPS32 revision support in the
kernel configuration

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:15:01 +01:00
Felix Fietkau
e9405aa8fd ramips/rt288x: switch CPU_TYPE to 24kc
While rt288x only has a MIPS 4KEc processor, it implements the MIPS32r2
architecture just like the 24Kc, so the instruction set should be 100%
compatible.
Switching it to 24kc allows it to share the package architecture with a
lot of other targets instead of creating a special case, saving
buildbot resources.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:15:01 +01:00
Vitaly Chekryzhev
07a02efd07 ramips: ZyXEL Keenetic series update wan mac
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-20 00:39:30 +01:00
Vitaly Chekryzhev
65985e9ace ramips: ZyXEL Keenetic Omni align factory images
ZyXEL web-flasher requires squashfs to be aligned to 64kb.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-20 00:39:30 +01:00
Vitaly Chekryzhev
f9d91a4ac7 ramips: correct keenetic-series switch index
Fix switch name typo

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-20 00:39:30 +01:00
Thibaut VARENE
7fb11c8ed2 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-01-18 12:06:16 +01:00
BangLang Huang
2a7f669016 ramips: fix mac address of miwifi-mini
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2017-01-18 12:05:14 +01:00
Joseph C. Lehner
6b5dab9469 ramips: simplify EX2700 network config
Don't create a vlan for the Netgear EX2700's only Ethernet port.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-01-18 08:54:58 +01:00
Rosen Penev
7967178cfc ramips: Add back sdhci-mt7620 driver to default config
The driver no longer causes kernel panics and CPU hangs.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-01-18 08:54:53 +01:00
John Crispin
c067011af8 ramips: add back the i2c-mt7621 module
mt7628/88 are still using this module.

Signed-off-by: John Crispin <john@phrozen.org>
2017-01-15 20:45:59 +01:00
Lazar Demin
ab90f15c89 ramips: Added Onion Omega2 and Omega2+
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
2017-01-15 17:43:14 +01:00
Rosen Penev
80768ddccd ramips: Add I2C driver to the default kernel config
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-01-15 17:43:05 +01:00
Felix Fietkau
1708644f19 kernel: backport MIPS changes introducing a separate IRQ stack
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-15 18:25:54 +01:00
Hauke Mehrtens
5b089e45a6 kernel: update 4.4 kernel to 4.4.42
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-13 23:05:36 +01:00
Yo Abe
29097b95ba ramips: fix WLI-TX4-AG300N boot and network
Partition label "linux" prevents the root file system to be mounted at
boot time leading to a kernel panic. After changing it to "firmware",
the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data"
are correctly recognized.

The attached IP175C 10/100 MBit switch cannot connect to a link with
fixed 1000Mbit speed. The correct link speed is 100MBit. The switch
is detected and can be configured via mdio bus and should allow two
separable VLANs to be configured for the 4 available ports.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[picked from openwrt/PR#330]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-13 08:32:35 +01:00
Andrew Yong
3f31029b19 ramips: add support for VoCore2
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
2017-01-13 08:32:35 +01:00
Daniel Golle
287283e6e3 ramips: rt3883: fix typo in pinctrl lna_g_func
Spotted by forum users
https://forum.openwrt.org/viewtopic.php?pid=347439#p347439

Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-13 05:44:06 +01:00
Antonis Kanouras
f2b6412c72 ramips: Fix VLAN limits for MT7621 GSW
Without this patch swconfig will only allow setting up a total of 16
VLANs, with VLAN ID range of 0-15.

Tested on ubnt-erx.

Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
2017-01-10 08:18:15 +01:00
Felix Fietkau
018d80007e kernel: remove ubifs xz decompression support
It has been unused, and less useful than squashfs for cases where flash
space usage matters.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-09 14:07:06 +01:00
Hauke Mehrtens
88ca6390ea kernel: bump to 4.4.40
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-06 19:38:55 +01:00
Felix Fietkau
84bd74057f build: use mkhash to replace various quirky md5sum/openssl calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:12 +01:00
Victor Shyba
d6c831e0e5 generic: mtd: backport SPI_NOR_HAS_LOCK
This flag was added to 4.9 with upstream commit
76a4707de5e18dc32d9cb4e990686140c5664a15.

Signed-off-by: Victor Shyba <victor1984@riseup.net>
[refresh and adjust platform patches, fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-03 19:58:00 +01:00
L. D. Pinney
b28e94d4bf ramips: MiWiFi Nano fixes
Use the the dt-bindings macros and add the reset button.

Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.

Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-02 19:16:54 +01:00
Rafał Miłecki
939ef157da ramips: fix NixcoreX1 profiles
There was a typo in Makefile that prevented using these profiles.

Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-12-28 23:05:24 +01:00
Mathias Kresin
0cf581ca3a ramips: use new image build code for more devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
a75ce960ac ramips: use different board names for variants
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.

Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
29f5e643ad ramips: sort rt305x image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b1148e75 ramips: use D-Link DIR-600 B1 image for B2 version
Everything set for the B1 is identical to the values uses for the B2
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b6bf1416 ramips: fix image validation errors
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.

Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
ae3ac76e56 ramips: use destinct 11AC NAS board name
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.

To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Henryk Heisig
4f033b2da6 ramips: fix tplink image building fix sysupgrade firmware on MR200
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:52:12 +01:00
Henryk Heisig
3a6353d910 ramips: enablemodem: move /lib/ramips.sh to start()
Fix build error: /etc/init.d/enablemodem: line 2: /lib/ramips.sh: No such file or directory

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:51:59 +01:00
Henryk Heisig
c8043137bb ramips: Add support to TP-Link Archer MR200
CPU: MT7620N 580MHz
Flash: 8MB
RAM: 64MB
build-in modem 3G/4G
four ethernet port 10/100Mbps

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-22 15:03:30 +01:00
Vitaly Chekryzhev
190ee7d86b ramips: add support for ZyXEL Keenetic Omni / Omni II
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2016-12-22 15:03:13 +01:00
Giuseppe Lippolis
96a7ee3c80 ramips: adding registration for si3210
The si3210 is a SLIC device providing a complete analog telephone
interface and therefore frequently used in soho router.
The si3210 have a native spi interface to be controlled by the CPU
but currently there is no dedicated driver in lede.
Adding a registration for this device in spidev allow to control the
device in user space.
This way of patching is also in line with the rationale of the spidev
driver, see: http://marc.info/?t=148145791900001&r=1&w=2
The si3210 has been also added in the DWR-512 DT to properly describe
the HW.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-12-20 09:35:37 +01:00
Kevin Darbyshire-Bryant
79abb8f140 kernel: bump to 4.4.39
Bump & refresh patches for all 4.4 targets.

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-12-20 09:35:36 +01:00
L. D. Pinney
02ca833f04 ramips: WNDR3700v5 fix mtd partitions and radios
Fix the mtd partition layout and enable both radios in the dts

Tested-by Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
2016-12-20 09:35:35 +01:00
Giuseppe Lippolis
132b88ea39 ramips: adding DWM-158 3g Modem
This patch add the 3G modem DWM-158 to the usb-serial option driver.
The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem
supportet by lede. The patch has been submitted and merged in the upstream
linux-next repository.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-12-14 10:37:01 +01:00
BangLang Huang
960c477432 ramips: Fix led init script for Lenovo Y1/Y1s
This commit fix the led init script for Lenovo Y1 and
Y1S due to the manual and dts file.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-12-04 15:51:18 +01:00
Felix Fietkau
566de813c3 ramips: prevent packet forwarding on mt7620 between switch ports during init (FS#103)
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.

REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-04 11:41:49 +01:00
Yong-hyu, Ban
377eac0ceb ramips: fix LAN port order of WeVO W2914NS v2
Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
2016-12-04 08:22:07 +01:00
BangLang Huang
23b58f8acb ramips: fix PBR-D1 button definition
Due to the product specification, the button on PBR-D1 should be
reset, not wps.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-12-04 07:03:17 +01:00
Tobias Wolf
2e020e2cef ramips: add support for PCI based OHCI/EHCI support for F5D8235 V1
This router uses an PCI attached NEC EHCI controller to support the single USB port.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
Tobias Wolf
13c0d208b2 ramips: introduce CONFIG_PCI and CONFIG_OF_*PCI for rt288x
This is a prerequisite for F5D8235 V1 to use PCI based OHCI/EHCI.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
Tobias Wolf
c2ed721e89 ramips: improve F5D8235 V1 support
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.

Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.

Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
John Crispin
7c809f1687 ramips: fix sdhci support on mt7621
the IRQ level was wrong. refresh the patch while at it.

Signed-off-by: John Crispin <john@phrozen.org>
2016-12-01 18:30:41 +01:00
Andrew Yong
07b571a435 ramips: RB750Gr3: Add pwr LED and buzzer to DTS
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-12-01 16:17:55 +01:00
Mathias Kresin
18c64f41c7 treewide: fix button keys codes used in dts
Use keycodes that matches the intended use case based on the label.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Mathias Kresin
4780e7e994 ramips: add size checks/append metadata where missing
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Mathias Kresin
6cc0ae27b9 ramips: fix Airlink AR670W factory image
Move the mkwrgimg build step to the makefile. It will be required by
other boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Yong-hyu, Ban
c723646f22 ramips: Add missing chunked-io directive to W2914NSV2.dtsi
Fix bug that LEDE failed to boot with this message:

WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214
mt7621_spi_transfer_one_message+0x28c/0x620()

Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
2016-11-26 22:39:21 +01:00
Andrew Yong
a7de18718d ramips: SamKnows SK-WB8 DTS cleanup
Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000).

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-26 22:35:52 +01:00
Mathias Kresin
ee6beb2e1c ramips: remove kmod-ledtrig-usbdev from recently added devices
None of the devices uses an usb led at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-24 22:37:40 +01:00
Giuseppe Lippolis
ec1de9b1a6 ramips: Add device DLINK DWR-512-B
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.

The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.

Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).

For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-11-23 08:36:11 +01:00
Mathias Kresin
8f561c6516 ramips: do not append metadata to CY-SWR1100 factory image
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 08:36:11 +01:00
Mathias Kresin
f1d0eba3ea ramips: cleanup dts files of mt7621 based boards
Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci
in mt7621.dtsi and enable the nodes in the indiviual board dts files.
The nodes require further device specific configuration anyway.

Remove the m25p80@0 spi child node from mt7621.dtsi and add the
chunked-io parameter to the individual board dts files. Fix the spi
flash compatible string for the WNDR3700V5.

Drop the mt7621-eval-board compatible string for all boards which are
not the eval board.

Drop the linux,modalias parameter from spi flash node.

Remove the xhci node from board files, it is already enabled in dtsi.
Disable xhci for boards not having usb ports populated.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 08:36:10 +01:00
Mathias Kresin
18e7f49975 ramips: order mt7621.mk alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 07:09:03 +01:00
Andrew Yong
fe43d90d93 ramips: fix wrong check for MT7621AT
fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-21 16:49:54 +01:00
Andrew Yong
605cab749e ramips: Fix sdhci kernel panics on MT7621
Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-21 12:31:39 +01:00
perillamint
68634426fe ramips: add support for WeVO W2914NS v2
Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
2016-11-21 10:13:17 +01:00
Felix Fietkau
478f1f6b16 ramips: append metadata to images
metadata checks are not enforced yet, because some images are still
being built by legacy code

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Vitaly Chekryzhev
348344874c ramips: add support for ZyXEL Keenetic Viva
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-18 08:54:57 +01:00
Vitaly Chekryzhev
5f38d1ad85 ramips: add MT7620 MIB support for switch and port
Move definitions to header. Replace array size definitions with macro.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[merged into 0513-net-mediatek-add-swconfig-driver-for-gsw_mt762x.patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
2016-11-17 20:01:21 +01:00
Jasper Scholte
3d680c5728 ramips: add support for Sitecom WLR-6000
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.

The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.

The stock firmware uses the following mac addresses:

LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5:   00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)

Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

2.4GHz: 00:0C:F6:AA:BB:D8
LAN:    00:0C:F6:AA:BB:D9
WAN:    00:0C:F6:AA:BB:DA
5 GHz:  00:0C:F6:AA:BB:DC

The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.

There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.

Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.

Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-17 06:39:52 +01:00
Dominik Menke
8b65fef173 ramips: add support for Digineo AC1200 Pro
This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash.

Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Dominik Menke
6e3d7897f7 ramips: cleanup ZBT-WG3526.dtsi
- replace magic numbers with GPIO_* constants
- replace generic PCI definitions with correct vendor and
  device identification

Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Dominik Menke
efbb654f6c ramips: split ZBT-WG3526.dts into dtsi and dts files
Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Martin Weinelt
5247ac2f80
ar71xx, ramips: reduce CPU load and flickering on devices using rsslieds
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.

Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-16 01:42:15 +01:00
Felix Fietkau
728ab77d3d ramips: fix polling switch interrupts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 20:06:15 +01:00
Felix Fietkau
3d0e965c8b ramips: add port index in switch config for buffalo WHR-* and WSR-* devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 20:04:36 +01:00
Felix Fietkau
4cdbc90a37 ramips: add hack to detect missing mt7621 cpu cores
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 19:59:32 +01:00
Felix Fietkau
a17872ec4f ramips: fix status LED for WHR-300HP2
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 17:55:27 +01:00
Mathias Kresin
2b55c83e68 treewide: dts: use keycode defines from input dt-binding
All compiled device tree files not mentioned are binary identical to the
former ones.

Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts.

Due to the include of the input binding header, the BTN_* node names in:

  - ramips/GL-MT300A.dts
  - ramips/GL-MT300N.dts
  - ramips/GL-MT750.dts
  - ramips/Timecloud.dts

will be changed by the compiler to the numerical equivalent.

Move the binding include of lantiq boards to the file where they are
used the first time to hint the user where the values do come from.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-13 07:07:58 +01:00
Mathias Kresin
77b807999d treewide: dts: use C style includes
No functional change but allows me to use one script to compile all
device tree source files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-12 21:04:15 +01:00
Mathias Kresin
de40d45363 treewide: dts: fix dtc compiler warnings
Fixes invalid device tree parameters.

Drop the mvsw61xx node used in mvebu device tree source files. It looks
like some kind of ethernet switch cargo cult. Neither the
marvell,88e6352 nor the marvell,88e6172 compatible strings can be found
in any LEDE file or in the kernel sources.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-12 21:04:15 +01:00
Mathias Kresin
cc5c8f681e ramips: add TEW-691GR/TEW-692GR 2.4 GHz interface mac addresses
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.

The MAC address numbering of the TEW-691GR changes to the following
pattern:

  LAN:  AA:BB:CC:DD:EE:0C
  WIFI: AA:BB:CC:DD:EE:0D
  WAN:  AA:BB:CC:DD:EE:0F

The MAC address numbering of the TEW-692GR changes to the following
pattern:

  LAN:    AA:BB:CC:DD:EE:e4
  WAN:    AA:BB:CC:DD:EE:e5
  2.4GHz: AA:BB:CC:DD:EE:e7
  5 GHz:  AA:BB:CC:DD:EE:e8

Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.

Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:23:00 +01:00
Mathias Kresin
d8dd207ea6 ramips: use the ralink,mtd-eeprom device tree property
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.

Set the label and compatible string according to the the PCI binding
documentation.

Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).

This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.

Use the usual eeprom for the soc wmac of the Dovado Tiny AC.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:22:59 +01:00
Roger Pueyo Centelles
5f6e948551 ramips: Add support for Wavlink WL-WN575A3
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:

 - CPU: MediaTek MT7628AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 2x 10/100 Mbps (switched)
 - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
 - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
 - Antennas: 4x external (2 per radio), non-detachable
 - LEDs: 4 programmable + LAN, WAN, POWER
 - Buttons: reset, WPS

Flashing instructions:

Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:

 - Client (WL-WN575A3) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-11-08 11:17:10 +01:00
BangLang Huang
bc4109845d ramips: fix Newifi D1 profile
the images were generated for the wrong flash size.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-11-08 11:17:10 +01:00
Sven Schwermer
5511c1c7c1 ramips: Use MT7621 I2C driver for MT7628/MT7688
The i2c-ramips driver does not work for the MT7628/MT7688 SoCs, the
i2c-mt7621 driver does.

Signed-off-by: Sven Schwermer <sven.schwermer@arcor.de>
2016-11-03 08:27:20 +01:00
Andrew Yong
faf94d926e ramips: add support for MikroTik hEX v3 (RB750Gr3)
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).

RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.

Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.

The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.

A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-02 10:25:44 +01:00
Stijn Segers
2f2ea7b44c kernel: update kernel 4.4 to version 4.4.30
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.

Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Stijn Segers
eefe07ef4d ramips: add usb packages into DIR-860L B1 profile
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Henryk Heisig
a34f96d6cf ramips: Archer C50 cleanup
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>

Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-31 16:58:41 +01:00
Rosen Penev
369884c2a1 ramips: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2016-10-31 16:41:26 +01:00
Xuefu Lin
8312738806 ramips: fix PSG1218 LEDs
Signed-off-by: Xuefu Lin  <xuefulin@gmail.com>
2016-10-26 12:37:45 +02:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
YuheiOKAWA
4050cfebda ramips: add support for Planex VR500.
SOC:	MT7621A
RAM:	256MiB
NOR:	MX25L51245G

Non Wireless Router.

Issue: soft reboot problem. SPI Flash do not exit 4byte address mode.

Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
2016-10-15 11:36:51 +02:00
Mathias Kresin
bcfbeae79f ramips: use rfkill for wps button on wlan only boards
All of the touched boards don't have an ethernet port. Allow to use the
wps button on these boards to enable the wireless radio after boot.

The force enabled wireless for the DCH-M225 is removed. It is reckless
to bring up an unencrypted wireless network by default these days.

Using the wps button to bring up the radio seam to me the better
approach.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
0a219c8dfb ramips: use rootfs splitter and new image build code for BR-6475ND
Use the edimax uImage splitter instead of the fixed size rootfs
partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
e7ec5df33b ramips: move edimax images to the new build code
Images installed via TFTP recovery or the Edimax webinterface of the
3g-6200n(l) are writting with the edimax header to flash.

Use only one image type for these boards. The migration to the
factory only images need to be done via TFTP recovery.

Use the same start address for the 3g-6200n(l) factory images as the
stock firmware images.

Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl
and the patient testing of all changes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
6391af2f1f ramips: improve edimax 6200n/nl support
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.

Add the internet led of the 6200nl and use the led for boot status
indication

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
51bca43f39 ramips: fix edimax 6200nl switch config
With 3a9752bbd2 and later changes to
ramips_set_preinit_iface() the default vlan config applied during
preinit was changed. These changes were made without updating the
default network config to ensure that vlan interfaces used for lan/wan
are still configured.

Fix the issue by using the default all LAN portmap and disabling not
connected switch ports using portdisable device tree parameter.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
bbdf2ac305 ramips: tag the CPU switch port
With de51026515 the explicit tagging of
the CPU port was removed. This leads to a not working default network
config, with vlans enabled but disabled CPU tagging, for boards where
all switch ports are having the same role.

In case the ports are having different roles set, tagging is is set
implicit for the CPU port by ucidef_add_switch().

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
b35dd9584e ramips: remove fixed lan/wan interface for switch configs
Don't set the lan/wan interface when using ucidef_add_switch. This
results into a wan interface albeit all ports a annotated as lan ports.

ucidef_add_switch takes care of setting the correct lan/wan interface
according to the annotation of the ports.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Klaus
df5416296c ramips: add support for Zyxel NBG-419N2 (WAP3205v2)
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files

Signed-off-by: Klaus <k-laus@quantentunnel.de>
2016-10-04 11:50:51 +02:00
Xuefu Lin
dce5c4f5c8 ramips: Add support for Phicomm K2 PSG1218
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet

Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
2016-10-04 11:50:46 +02:00
Álvaro Fernández Rojas
7d559169c5 kernel: update to v4.4.23
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-30 20:08:21 +02:00
Stijn Segers
949cfbb243 kernel: update kernel 4.4 to version 4.4.22
Forgot to update kernel-version.mk, so updated patch. Compile-tested on x86/64 and ar71xx; run-tested on x86/64 and ar71xx.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-09-30 13:34:04 +02:00
Cezary Jackiewicz
e79e555c0e ramips: Xiaomi MiWiFi Nano: fix status led
- add status led for Xiaomi MiWiFi Nano
- revert af1e70b4a7 , this should not be added.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-29 11:39:41 +02:00
BangLang Huang
142ec7ada9 ramips : add support for Newifi D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
BangLang Huang
9fe833e1d0 ramips : add support for PandoraBox D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
Cezary Jackiewicz
66aae9a271 ramips: Add support for ZBT-CPE102
- CPU: MT7620N 580MHz
- Flash: 8MB
- RAM: 64MB
- build-in minipcie slot for modem 3G/4G
- one ethernet port 10/100Mbps

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-27 17:50:21 +02:00
Matthias Schiffer
43bf3e80b2
ramips: fix DEVICE_PACKAGES of Ubiquiti EdgeRouter X
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-26 17:57:57 +02:00
Matthias Schiffer
175fbe4d4e
ramips: move /lib/ramips.sh include in /etc/init.d/bootcount into start()
Enabling the init script offline will print an error otherwise.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-25 23:26:42 +02:00
Martin Blumenstingl
d72e838429 ramips: do not "local" variables outside of a function
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-09-24 01:17:18 +02:00
Álvaro Fernández Rojas
41eab9048b kernel: update kernel 4.4 to version 4.4.21
Refresh patches for all targets that support kernel 4.4.
Compile-tested on brcm2708 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-16 10:17:27 +02:00
Mathias Kresin
eb88a9cacb ramips: fix wrong blocksizes
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.

I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.

The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.

Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-15 09:53:37 +02:00
Álvaro Fernández Rojas
d14c28fc80 kernel: update kernel 4.4 to version 4.4.20
Refresh patches for all targets that support kernel 4.4.
Compile-tested on brcm2708 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-15 08:10:55 +02:00
Mathias Kresin
925e63e71f ramips: enable 4K sector support in kernel config
This is a follow up to 28110727f1
"ramips: set blocksize for 4MB devices". I've missed to include the
required changes of the kernel configs to enable 4K sector size
support.

The option is only enabled for targets having boards with 4k sector
size flash chips.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-13 22:06:08 +02:00
Mathias Kresin
1cd0a4c688 image: add KERNEL_SIZE to the default device vars
This reverts commit ec37a56587 and fixes
the underlying issue.
2016-09-13 19:36:41 +02:00
Felix Fietkau
d27bce8d28 build: drop UBI EOF marker from images by default
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-12 18:21:52 +02:00
Mathias Kresin
c1578d4fc9 cleanup ucidef_set_interface* usage
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:32:25 +02:00
Mathias Kresin
0f6d0afa13 ramips: board.d merge redundant switch/interface configs
Fix alphabetical order distortions as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:28:38 +02:00
Mathias Kresin
7d9ef9080c ramips: set blocksize for remaining rt3883 devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 21:03:57 +02:00
Mathias Kresin
9f531efc59 ramips: remove old build code seama recipe
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 15:27:46 +02:00
Mathias Kresin
fb39b77ccb ramips: switch DIR-610 A1 to new image build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 22:21:23 +02:00
Mathias Kresin
bd39104e95 ramips: switch some rt3883 devices to new build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 10:18:31 +02:00
Mathias Kresin
0f3600ccee ramips: move seama build recipe to Makefile
The identical build step is defined twice. Move it to the parent
Makefile to use only one version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:43:31 +02:00
Mathias Kresin
74da44cfc2 ramips: switch DIR-615 H1 to new image build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-02 07:34:36 +02:00
Mathias Kresin
483fd5f6ad ramips: add build recipe for senao header
Add it to the Makefile to allow a board which will be supported soon
to use the recipe as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-17 07:49:34 +02:00
Mathias Kresin
28110727f1 ramips: set blocksize for 4MB devices
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.

Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.

The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.

For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:

  - Ralink V11ST-FE
  - Ralink AP-RT3052-V22RW-2X2
  - MediaTek MT7628 EVB
  - MediaTek MT7621 EVB
  - UPVEL UR-326N4G
  - Buffalo WZR-AGL300NH

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:56:35 +02:00
Mathias Kresin
05ab2323ff ramips: don't set the same max image size twice
The ralink_default_fw_size_8M is already set for the default device.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 10:04:20 +02:00
Mathias Kresin
a499d0a6b5 image: specify max image size in Kilobyte/Megabyte
Use the k and m unit suffix to be consistent with the blocksize.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 09:58:02 +02:00
Mathias Kresin
e7ec7a08aa image: use k as unit suffix for blocksize
Use k as unit suffix for kilobyte to have a the same unit regardless of
the used filesystem.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 08:56:05 +02:00
Mathias Kresin
85fefcdb61 kernel: mtd: backport Macronix sector size fix
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:27:09 +02:00
Mathias Kresin
5369a03d52 ramips: use lower case names for TEW-69xGR images
Use lower case variant of the device name for to images to be
consistent with all other images names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-09 07:12:37 +02:00
Mathias Kresin
775f93e898 ramips: fix wrong TARGET_DEVICES
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 23:51:46 +02:00
Mathias Kresin
034c5cb820 ramips: fix wrong device title
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 07:32:00 +02:00
Daniel Golle
083ef3fefe ramips: add support for Mercury MAC1200R v2
MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM
reset button GPIO is still missing (anyone?)
bootloader password is 'slp'

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-09-09 02:38:06 +02:00
Felix Fietkau
aa53f78038 build: fix subtarget descriptions
Move Target/Description above the target.mk include

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-04 13:35:11 +02:00
Felix Fietkau
358cd6d9eb ramips: fix legacy initramfs images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-03 10:47:42 +02:00
Jonas Gorski
b962da4d92 ramips: mt7621: switch to 24kc
1004kc is just a SMP capable 34kc, and GCC treats 24kc and 34kc exactly
the same and will generate identical code, so there is no need to tune
to 1004kc instead of 24kc.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-08-23 11:55:32 +02:00
Stijn Tintel
8072264b96 kernel: update kernel 4.4 to version 4.4.19
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-08-23 10:51:17 +03:00
Mathias Kresin
c9e6b173f7 ramips: fix build of TRENDnet TEW-69xGR images
The image generation for TEW-691GR and TEW-692GR was broken since
79d02229 due to the move of the UMedia recipe to another Makefile.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Mathias Kresin
c892f37b30 ramips: move umedia build step to Makefile
Some rt3883 based boards need this one as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Mathias Kresin
bcd2113a32 ramips: TEW-691GR: fix switch and wireless
Due to the missing phy-mode setting, the switch wasn't initialised.

The wireless requires an eeprom to work. Use the same mac addresses as
the stock firmware.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Mathias Kresin
a7c6cf5182 ramips: TEW-692GR: fix switch and wireless
The AR8327 initvals were not copied to the DTS during the switch from
mach file to device tree and broke the switch on the device.

The former used PORT6 related initvals were wrong and have been
corrected.

The phy mode setting for the switch was missing in the DTS as well.

The wireless requires an eeprom to work. The dual band wireless chips
have both bands enabled by default but only one band per chip is
working.

The stock firmware uses the following mac addresses:

LAN:    AA:BB:CC:DD:EE:E4
WAN:    AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
5 GHz:  AA:BB:CC:DD:EE:E8

Assuming the mac address range :E4 to :E8 is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

LAN:    AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
WAN:    AA:BB:CC:DD:EE:E5
5 GHz:  AA:BB:CC:DD:EE:E8

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:45:45 +02:00
Mathias Kresin
05912a304c ramips: rt3883: fix dtc compiler warning
Fixes the following compiler warning:

Warning (reg_format): "reg" property in /ethernet@10100000/port@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /ethernet@10100000/port@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /ethernet@10100000/port@0

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:42:42 +02:00
John Crispin
99a1888287 swconfig: revert the portmapping patches, they seem to cause a segfault
Revert "kernel/swconfig: remove obsolete portmapping feature from swconfig"

This reverts commit 675407baa4.

Revert "swconfig: remove obsolete portmapping feature"

This reverts commit fca1eb349e.

Signed-off-by: John Crispin <john@phrozen.org>
2016-08-16 10:20:01 +02:00
John Crispin
675407baa4 kernel/swconfig: remove obsolete portmapping feature from swconfig
Signed-off-by: John Crispin <john@phrozen.org>
2016-08-15 15:18:35 +02:00
Felix Fietkau
592c0a1cd2 ramips: fix legacy image build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-11 17:07:37 +02:00
Chuanhong Guo
0f73801f4f ramips: Add support for Thunder Timecloud
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-08-10 03:04:08 +02:00
Jimmy Zhong
2b1f4945b1 ramips: Add support for TEW-714TRU
Signed-off-by: Jimmy Zhong <mb300sd@mb300sd.net>
2016-08-10 03:03:50 +02:00
Jonas Gorski
bebcb81da5 ramips: switch from 24kec to 24kc
Since the only difference between 24Kec and 24Kc is the addition of DSP
ASE support, and we don't use it anymore, there is no need to keep 24Kec
as a separate cpu type.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-08-08 11:29:56 +02:00
John Crispin
281483e097 ramips: enable nand support for mt7621
this makes sysupgrade work on the ERX

Signed-off-by: John Crispin <john@phrozen.org>
2016-08-03 15:30:13 +02:00
John Crispin
8e75630d1d ramips: updated remaining profiles to the new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-08-03 15:30:13 +02:00
Felix Fietkau
9abbaa9539 build: remove MIPS dsp/dsp2 CPU_SUBTYPE
There does not seem to be any meaningful difference in generated code.
This will save some time and space on snapshot builds

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-03 14:56:45 +02:00
P.Wassi
686617ae39 ramips: Rename TP-Link Archer C50 LEDs
Rename LEDs in TP-Link Archer C50 from [manufacturer name]
to [board name] ("tp-link" -> "c50")

Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-26 08:39:36 +02:00
P.Wassi
dbf107cd2b ramips: Improve TP-Link Archer C20i support
Improve / finalise TP-Link Archer C20i support.

Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-26 08:39:36 +02:00
Felix Fietkau
63b525dd6b image: add a helper variable for getting kernel/rootfs from within image Build/* templates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-31 12:25:25 +02:00
Jo-Philipp Wich
db49dd894e build: rename sysupgrade-nand to sysupgrade-tar
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-29 16:53:03 +02:00
P.Wassi
525b9edc8a ramips: unify etc/board.d/01_leds configuration
Introduce an optional parameter at the local set_usb_led and
set_wifi_led function such that they can take a triggering
device. If no parameter is passed, behaviour is unchanged.
Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-24 06:38:30 +02:00
Michael Lee
0d5277f73f ramips: dch-m225 don't have ethernet. default enable wifi
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-24 06:38:30 +02:00
Paul Wassi
104114fe00 ramips: remove indentation in etc/board.d/01_leds
Remove indentation at end of line in base-files/etc/board.d/01_leds
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-07-24 06:38:29 +02:00
John Crispin
6674006bd0 ramips: add missing i2s alias
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-24 06:38:29 +02:00
Jo-Philipp Wich
b051ac76e8 ramips: mt7621: add missing kernel symbol
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-16 13:59:12 +02:00
Hauke Mehrtens
efa1960abb kernel: update kernel 4.4 to version 4.4.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-07-13 15:39:15 +02:00
Michael Lee
9062c4fe99 ramips: modify audio kernel module and add dma options
* add gdma and hsdma kernel modules
* i2s support all ramips targets except rt288x
* i2s need gdma to transfer data
* add simple audio kernel module. it support device tree binding

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee
c3e420f28c ramips: Add support for D-Link DCH-M225
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee
36d98e6c7a ramips: add MT7620 pinmux bits for mdio as refclk
The MT7620 uses a 2 bit wide configuration of the mdio.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee
0460e9ffca ramips: enable MTD_SPLIT_SEAMA_FW for mt7620
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
L. D. Pinney
cf8c77be6b ramips: Add support for the NixCore X1 Module
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.

http://nixcores.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
2016-07-11 14:19:47 +02:00
Rene Treffer
8876575601 ramips: fix partition size for RT5350F-OLINUXINO
The partition size is wrong, leading to out-of-disk-space even on no/moderate use.

Upstream fix from vendor: 2f25eb57ed
Suggested fix for openwrt: https://dev.openwrt.org/ticket/20321

Signed-off-by: Rene Treffer <treffer@measite.de>
2016-07-11 14:19:47 +02:00
John Crispin
252f751611 ramips: fix usb phy initialisation
this broke usb20 device detection.

Signed-off-by: John Crispin <john@phrozen.org>
2016-07-11 14:19:46 +02:00
Felix Fietkau
201dbb9fe8 ramips: fix build error in ubnt-erx initramfs factory image
Build initramfs kernel image, but skip factory image if initramfs size
is too big.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-06 10:12:37 +02:00
John Crispin
eca1021e5c ramips: fix buffalo wmr-300 lan port
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:14 +02:00
John Crispin
2c9073282d ramips: fix MT7621 gsw handling
based on https://forum.openwrt.org/viewtopic.php?pid=323671#p323671

Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:13 +02:00
John Crispin
69a626b441 ramips: fix mt7621 SoC detection
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:13 +02:00
John Crispin
d09f0045ea ramips: fix up switch settings for Sitecom WL-351 v1 002
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
2016-07-03 08:00:26 +02:00
John Crispin
2dc9beddc0 ramips: disable the WP pin on the SDK mmc driver
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-30 22:48:39 +02:00
John Crispin
81add8f753 ramips: fix pinmux typo
Reported-by: Joy Kicer <joykicer@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-30 22:48:39 +02:00
Matthias Schiffer
0a0caa2656
ramips: set correct LAN/WAN MAC addresses on DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Matthias Schiffer
103ed00cfb
ramips: add button support and make LEDs known to userspace for DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Matthias Schiffer
fa9811814a
ramips: fix fixseama call on first boot
Commit "kernel: mtdsplit: calculate kernel partition precisely for Seama"
changed the kernel partition to only contain the kernel itself and not
the Seama header. Adjust the fixseama call to match what is used on
brcm53xx.

This fixes failing to boot a second time after flashing the factory image
on the affected devices.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Hauke Mehrtens
84d489f64f kernel: update to version 4.4.14
Changelog: https://cdn.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.14

Some manual changes to target/linux/generic/patches-4.4/610-
netfilter_match_bypass_default_checks.patch were needed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:20:37 +02:00
Roger Pueyo Centelles
5fba0f0c0c ramips: add suport for ZBT APE522II
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-06-22 19:32:06 +02:00
Michael Lee
81913e4996 ramips: remove duplicate i2c dts info
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-20 11:45:44 +02:00
Michael Lee
60ccfbbad0 ramips: update i2c drivers
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
  so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
  it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
  it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
  not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
  names. and the hardware don't support error status. so i remove it.
  but the logic is the same.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-20 11:45:44 +02:00
John Crispin
b180f24a3b Revert "ramips: update i2c drivers"
This reverts commit d8202a8409.

the commit broke I2C on various boards.

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 04:13:07 +02:00
John Crispin
bfcbca3e04 mediatek/ralink: fix boardnames
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 13:00:30 +02:00
Jo-Philipp Wich
5550d98015 ramips: fix kmod-sound-mt7620 packaging
Commit 9ff8928bb9 renamed the snd-soc-mt7620-i2s
driver and dropped snd-soc-mt7620-wm8960 which selected CONFIG_SND_SOC_WM8960
breaking all ramips builds due to undefined kernel config symbols.

Rework the kmod-sound-mt7620 package to explicitely select the
CONFIG_SND_SOC_WM8960 symbols and change it to bundle the renamed .ko file.

Also remove the @BROKEN flag and exclude it on the rt288x subtarget instead.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-14 14:31:18 +02:00
Henryk Heisig
01fb393c67 ramips/image: Add Archer C50 to mt7620 Makefile
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Henryk Heisig
75af981239 ramips/base-files: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Henryk Heisig
1c00c09eb6 ramips/dts: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Michael Lee
9a4935687d ramips: add support for DuZun DM06
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee
49b7421836 ramips: enable wm8960 kernel menuconfig select option
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee
6f61990d15 ramips: add i2s clocks
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee
921d782eb7 ramips: update i2s dtsi files
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
9ff8928bb9 ramips: improve i2s drivers
* remove mt7620-wm8960.c use simple card and DTS to do it
* add old chips support
* add 12Mhz refclk setup. this is hard code. need use clock framework
  rewrite it
* add interrupt error status support for debug. default disable it.
  because it cause to many interrupts
* add setup bclk suport not hard code it
* add 24 bits support for mt7628. not verified
* use regmap api to control registers
* add txdma-req/rxdma-req DTS params for DMA use

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
42bbe28cf1 ramips: add i2c clock
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
011ce1fad6 ramips: update i2c dtsi files
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
d8202a8409 ramips: update i2c drivers
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
  so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
  it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
  it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
  not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
  names. and the hardware don't support error status. so i remove it.
  but the logic is the same.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
f36d624d88 ramips: add gdma hsdma dts info
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee
f6fc591561 ramips: enhance dma engine support
* fix compiler error. device_control operation not support now.
* add old chips support 8 channels. new chips support 16 channels.
* add mt7621 hsdma driver. data sheet says it has two channels.
  but after test only one channel support.
* add memory to memory DMA support. i use dmatest kernel module to
  verify this function. on rt305x it will copy more data. on mt7621
  only two channels can works at the same time. these two chips
  maybe have hardware bugs. because on other chips don't have these bugs.
* use tasklet to handle remaining dma requests.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Álvaro Fernández Rojas
0aa6c7df60 kernel: update kernel 4.4 to version 4.4.13
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-12 15:51:54 +02:00
Felix Fietkau
7eeb254cc4 treewide: replace nbd@openwrt.org with nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-07 08:58:42 +02:00
Joseph C. Lehner
065de8bd7a ramips: fix Netgear EX2700 images
Calling `cat foo bar | dd ... conv=sync` *may* add
extraneous padding. Avoid this.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-06-05 23:23:57 +02:00
Joseph C. Lehner
8b0fbd8e70 ramips: rebrand Netgear EX2700 fakeroot uImage
Change image name: "OpenWrt fakeroot" -> "LEDE fakeroot"

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-06-05 23:23:57 +02:00
Álvaro Fernández Rojas
29b412b8c5 ramips: add kmod-pwm-mediatek for mt7628/mt7688
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 13:24:25 +02:00
Álvaro Fernández Rojas
604b92dbd0 ramips: fix the number of uarts for each SoC
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 12:20:33 +02:00
Álvaro Fernández Rojas
243e79e10c ramips: fix Mi Wi-Fi Nano Wireless LED pinmux
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 12:19:57 +02:00
Álvaro Fernández Rojas
a105eac4dd kernel: update kernel 4.4 to version 4.4.12
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-02 15:34:34 +02:00
Yuan Chenmang
b38296f2f6 ramips: add Widora-NEO board support
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.

Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-01 12:52:28 +02:00
Joseph C. Lehner
2a589539ba ramips: fix Netgear EX2700 images
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-05-30 22:52:59 +02:00
Joseph C. Lehner
b232669d45 ramips: fix Netgear EX2700 images
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-05-27 15:50:18 +02:00
Álvaro Fernández Rojas
2a57a54d49 ramips: add backported MT7628 pinmux fixes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-29 11:26:41 +02:00
Cezary Jackiewicz
af1e70b4a7 ramips: Add status led for Xiaomi MiWiFi Nano
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 22:43:37 +02:00
John Crispin
bf6634339a ramips: fix timing issues when using MT7621 spi
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-23 20:22:22 +02:00
John Crispin
c7efbd7dbb ramips: Add specific compatible properties for esw
Currently, for RT5350 and MT7628, esw is marked as compatible with
"ralink,rt3050-esw". While this is true, the switches within RT5350
and MT7628 actually support more functionality than the RT3050 switch.

One such example is per-VLAN untagging, which is an important feature.

RT3352 is another example of this, but it already has an additional
compatible property, which allows to differentiate it from RT3050.

This commit adds such more specific properties for RT5350 and MT7628
as well.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-23 11:28:59 +02:00
Cezary Jackiewicz
2965430999 ramips: cleanup for Hame MPR-A2
- disable all ethernet ports except port 0 on MPR-A2

Port 0 is the only ethernet port on this router, so disable all other PHYs in order to save power.

- don't use a VLAN for the single ethernet port of the MPR-A2

Like A5-V11, this router only has one ethernet port.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 11:03:23 +02:00
Felix Fietkau
5166732a4e ramips: use green power LED as status indicator for Buffalo WSR-1166 and WSR-600
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-21 15:16:37 +02:00
Felix Fietkau
82dcbec727 ramips: remove fake vlan rx offload from ethernet driver
The network stack does not need it to do GRO

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-20 14:01:21 +02:00
Álvaro Fernández Rojas
3bc90f9626 ramips: use backported upstream patches
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-19 17:48:41 +02:00
Álvaro Fernández Rojas
638d509817 ramips: fix pinctrl regression
This regression was introduced in commit 9195d8da.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-18 22:08:39 +02:00
Álvaro Fernández Rojas
29db5cae43 ramips: fix spidev generic nodes
Use linux,spidev compatible string.
Move MZK-DP150N spidev to spi1 node.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-18 22:08:39 +02:00
Álvaro Fernández Rojas
021c893658 ramips: fix size-cells on spi nodes
size-cells should be 0 in order to avoid dummy values in reg properties.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-18 16:57:39 +02:00
John Crispin
2a6b899589 ramips: fix 8M WT3020 image creation
fix image size for 8M version : 4M -> 8M

Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
2016-05-16 20:59:06 +02:00
John Crispin
1d9c0b2409 ramips: fix ArcherC20i image creation - 3rd try
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-15 11:59:43 +02:00
Felix Fietkau
ce009d16a1 ramips: fix Archer C20i image build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-15 14:11:26 +02:00
John Crispin
5d0eff9801 ramips: set default profile to priority 1
doing so will sort all profiles alphabetically

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-14 21:27:16 +02:00
John Crispin
7697aced24 ramips: fix ArcherC20i image creation
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-14 21:26:05 +02:00
Felix Fietkau
27dfe64887 ramips/mt7621: remove cflags override
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-14 17:58:43 +02:00
Álvaro Fernández Rojas
20b069c440 ramips: disable unused ethernet ports on VoCore
Only ports 0 and 4 are used so disable the other ones in order to save power.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-14 12:40:03 +02:00
Felix Fietkau
7fab5dc486 ramips: fix indentation of Build/* template commands
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-12 19:49:38 +02:00
John Crispin
f10d2bb6d3 ramips: add wmac nodes to all mt7628/88 dts files
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
Andrew Yong
8c9b8d70b1 ramips: add status led for ZBT-WE826
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:36 +02:00
John Crispin
4220cc3255 ramips: convert mt7620 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
John Crispin
ecbaaa401a ramips: convert mt7688 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
John Crispin
0f12f32996 ramips: convert mt7628 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
John Crispin
825717d450 ramips: convert mt7621 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
John Crispin
a55f0c32fa ramips: convert rt2880 to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
Stanislav Galabov
ffaaa6788a ramips: DTS modifications
This commit makes the following modifications to ramips dts files:
1. Add clkctrl node to all dtsi files (although not used for now)
2. Add clocks and clock-names properties to some nodes (usbphy, pci)
3. Add usbphy node for rt3050 (although not used for now)
4. Add clock-frequency to uart nodes in mt7621.dtsi and mt7628an.dtsi

These modifications, although not fully used at the moment, will make
it easier for FreeBSD to adopt and use LEDE ramips dts files with
minimal changes for easier maintenance.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-12 03:29:36 +02:00
John Crispin
b8ab6af1a9 global: change my email address
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
Andrew Yong
374cae9e6f ramips: add initial support for SamKnows SK-WB8
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:35 +02:00
Stanislav Galabov
9195d8da35 ramips: DTS rework
Add node aliases to dtsi files.
Reword dts files so they're more in-line with upstream.
Fix some more warnings and errors reported by dtc

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-12 03:29:35 +02:00
Álvaro Fernández Rojas
e32b2f92b1 kernel: update kernel 4.4 to version 4.4.10
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-11 21:34:27 +02:00
John Crispin
f6059cc118 ramips: fix DTB generation
using preprocessor style includes when calling dtc directly.

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-10 14:44:05 +02:00
Stanislav Galabov
f8b6c9d825 ramips: Change all '/include/' clauses to '#include' so preprocessing can
be done properly for the entire device trees.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-10 10:43:17 +02:00
Stanislav Galabov
600c224213 ramips: Add hex prefix (0x) to dtsi reg properties where needed.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-10 10:43:17 +02:00
Stanislav Galabov
b8f73d7f0a ramips: introduce serial0 aliases
This patch introduces serial0 aliases in the ramips DTS files, which can
then be used to denote the active console instead of relying on bootargs.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-10 10:43:17 +02:00
Álvaro Fernández Rojas
b062266ad6 kernel: update kernel 4.4 to version 4.4.9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-10 10:43:17 +02:00
D. Andrei Măceș
823c58a1cf ramips: mt7620: [UPSTREAM] fix USB frequency scaling
The logic for the SoC check got inverted. We need to check if it's
not a MT76x8.

Signed-off-by: D. Andrei Măceș <dmaces@nd.edu>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam)
1570277094 ramips: Fix alphabetical sorting for 02_network
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam)
39f035fdc7 ramips: Don't use a VLAN for the single ethernet port of the A5-V11.
This router only has one ethernet port, so a VLAN is useless here, now that the rt3050 TCP bug that happened without VLANs has been fixed for a very long time.

Add this router to the VLAN-less config that is used by other single-port routers.

Also fix MAC address detection code since this router has no WAN port.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam)
ffb7bf7672 ramips: Fix network for routers without VLANs on eth0.
Some routers only have one port, so eth0 is used without VLANs for them.

Revision r47720 introduced some changes, but wrongly confused "enable" with "reset".

VLANs need to be disabled for those routers, and the switch may be reset.

Fix this, by explicitly disabling VLANs instead of resetting the switch for these routers.

Also merge duplicate configuration for the "m2m".

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:12 +02:00
blogic
40bfe9f0bd ramips: Drop hacky switch workaround for failsafe on rt3x5x and rt5350.
The new rt3050 switch driver doesn't have problems with TCP when not
using VLANs.

This piece of code also broke failsafe for all routers where the LAN
port is not wired to port 0 of the internal switch.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49293
2016-05-10 10:43:12 +02:00
blogic
3f638902b6 ramips: Disable all ethernet ports except port 0 on A5-V11.
Port 0 is the only ethernet port on this router, so disable all other PHYs
in order to save power.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 49292
2016-05-10 10:43:12 +02:00