openwrtv4/target/linux/ramips/image/Makefile

1150 lines
45 KiB
Makefile
Raw Normal View History

#
# Copyright (C) 2008-2011 OpenWrt.org
#
# This is free software, licensed under the GNU General Public License v2.
# See /LICENSE for more information.
#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
define imgname
$(BIN_DIR)/$(IMG_PREFIX)-$(2)-$(1)
endef
define sysupname
$(call imgname,$(1),$(2))-sysupgrade.bin
endef
VMLINUX:=$(IMG_PREFIX)-vmlinux
UIMAGE:=$(IMG_PREFIX)-uImage
define Image/Build/Initramfs
$(call Image/Build/Profile/$(PROFILE),initramfs)
endef
DEVICE_VARS += DTS
loadaddr-y := 0x80000000
loadaddr-$(CONFIG_TARGET_ramips_rt288x) := 0x88000000
loadaddr-$(CONFIG_TARGET_ramips_mt7621) := 0x80001000
KERNEL_LOADADDR := $(loadaddr-y)
KERNEL_DTB = kernel-bin | patch-dtb | lzma
define Device/Default
KERNEL := $(KERNEL_DTB) | uImage lzma
IMAGES := sysupgrade.bin
IMAGE_SIZE := $(ralink_default_fw_size_8M)
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
endef
define Build/patch-dtb
$(call Image/BuildDTB,../dts/$(DTS).dts,$@.dtb)
$(STAGING_DIR_HOST)/bin/patch-dtb $@ $@.dtb
endef
define Build/trx
$(STAGING_DIR_HOST)/bin/trx \
-o $@ \
-m $(IMAGE_SIZE) \
-f $(word 1,$^) \
-a 4 -f $(word 2,$^)
endef
define Build/seama
$(STAGING_DIR_HOST)/bin/seama -i $@ $(1)
mv $@.seama $@
endef
define Build/seama-seal
$(call Build/seama,-s $@.seama $(1))
endef
define Build/relocate-kernel
( \
dd if=$(KDIR)/loader.bin bs=32 conv=sync && \
perl -e '@s = stat("$@"); print pack("V", @s[7])' && \
cat $@ \
) > $@.new
mv $@.new $@
endef
ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX) This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
define Build/ubnt-erx-factory-compat
echo '21001:6' > $@.compat
$(TAR) -cf $@ --transform='s/^.*/compat/' $@.compat
$(RM) $@.compat
endef
define Build/ubnt-erx-factory-kernel
if [ -e $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE) ]; then \
$(TAR) -rf $@ --transform='s/^.*/vmlinux.tmp/' $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE); \
\
md5sum --binary $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE) | awk '{print $$1}'> $@.md5; \
$(TAR) -rf $@ --transform='s/^.*/vmlinux.tmp.md5/' $@.md5; \
$(RM) $@.md5; \
fi
endef
define Build/ubnt-erx-factory-rootfs
echo "dummy" > $@.rootfs
$(TAR) -rf $@ --transform='s/^.*/squashfs.tmp/' $@.rootfs
md5sum --binary $@.rootfs | awk '{print $$1}'> $@.md5
$(TAR) -rf $@ --transform='s/^.*/squashfs.tmp.md5/' $@.md5
$(RM) $@.md5
$(RM) $@.rootfs
endef
define Build/ubnt-erx-factory-version
echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $@.version
$(TAR) -rf $@ --transform='s/^.*/version.tmp/' $@.version
$(RM) $@.version
endef
#We need kernel+initrams fit into kernel partition
define Build/ubnt-erx-factory-check-size
@[ $$(($(subst k,* 1024,$(subst m, * 1024k,$(1))))) -ge "$$($(TAR) -xf $@ vmlinux.tmp -O | wc -c)" ] || { \
echo "WARNING: Initramfs kernel for image $@ is too big (kernel size: $$($(TAR) -xf $@ vmlinux.tmp -O | wc -c), max size $(1))" >&2; \
$(RM) -f $@; \
}
@[ "$$($(TAR) -xf $@ vmlinux.tmp -O | wc -c)" -gt 0 ] || { \
echo "WARNING: Kernel for image $@ not found" >&2; \
$(RM) -f $@; \
}
endef
define MkCombineduImage
$(call PatchKernelLzma,$(2),$(3))
if [ `stat -c%s "$(KDIR)/vmlinux-$(2).bin.lzma"` -gt `expr $(4) - 64` ]; then \
echo "Warning: $(KDIR)/vmlinux-$(2).bin.lzma is too big" >&2; \
else if [ `stat -c%s "$(KDIR)/root.$(1)"` -gt $(5) ]; then \
echo "Warning: $(KDIR)/root.$(1) is too big" >&2; \
else \
( dd if=$(KDIR)/vmlinux-$(2).bin.lzma bs=`expr $(4) - 64` conv=sync ; dd if=$(KDIR)/root.$(1) ) > $(KDIR)/vmlinux-$(2).bin.lzma.combined ; \
fi ; fi
$(call MkImage,lzma,$(KDIR)/vmlinux-$(2).bin.lzma.combined,$(call sysupname,$(1),$(2)),$(6))
endef
#
# The real magic happens inside these templates
#
# $(1), compression method
# $(2), filename of image data
# $(3), output filename
define MkImage
$(eval imagename=$(if $(4),$(4),MIPS OpenWrt Linux-$(LINUX_VERSION)))
-mkimage -A mips -O linux -T kernel -C $(1) -a $(loadaddr-y) -e $(loadaddr-y) \
-n "$(imagename)" \
-d $(2) $(3)
endef
define CompressLzma
$(STAGING_DIR_HOST)/bin/lzma e $(1) -lc1 -lp2 -pb2 $(2)
endef
define MkImageSysupgrade/squashfs
$(eval output_name=$(IMG_PREFIX)-$(2)-$(1)-$(if $(4),$(4),sysupgrade).bin)
cat $(KDIR)/vmlinux-$(2).uImage $(KDIR)/root.$(1) > $(KDIR)/$(output_name)
$(call prepare_generic_squashfs,$(KDIR)/$(output_name))
if [ `stat -c%s "$(KDIR)/$(output_name)"` -gt $(3) ]; then \
echo "Warning: $(KDIR)/$(output_name) is too big" >&2; \
else \
$(CP) $(KDIR)/$(output_name) $(BIN_DIR)/$(output_name); \
fi
endef
define MkImageTpl/squashfs
$(eval output_name=$(IMG_PREFIX)-$(2)-$(1)-$(if $(4),$(4),sysupgrade).bin)
$(STAGING_DIR_HOST)/bin/mktplinkfw2 -V "ver. 2.0" -B "$(2)" -j \
-o $(KDIR)/$(output_name) \
-k $(KDIR)/vmlinux-$(1)$(4).bin.lzma \
-r $(KDIR)/root.$(1)
$(CP) $(KDIR)/$(output_name) $(BIN_DIR)/$(output_name)
endef
define MkImageTpl/initramfs
$(eval output_name=$(IMG_PREFIX)-$(2)-$(1).bin)
$(STAGING_DIR_HOST)/bin/mktplinkfw2 -V "ver. 2.0" -B "$(2)" -c \
-o $(KDIR)/$(output_name) \
-k $(KDIR)/vmlinux-$(1).bin.lzma
$(CP) $(KDIR)/$(output_name) $(BIN_DIR)/$(output_name)
endef
# $(1), lowercase board name like "mt7620a_v22sg"
# $(2), DTS filename without .dts extension
# $(3), optional filename suffix, e.g. "-initramfs"
define PatchKernelLzmaDtb
cp $(KDIR)/vmlinux$(3) $(KDIR)/vmlinux-$(1)$(3)
$(LINUX_DIR)/scripts/dtc/dtc -O dtb -o $(KDIR)/$(2).dtb ../dts/$(2).dts
$(STAGING_DIR_HOST)/bin/patch-dtb $(KDIR)/vmlinux-$(1)$(3) $(KDIR)/$(2).dtb
$(call CompressLzma,$(KDIR)/vmlinux-$(1)$(3),$(KDIR)/vmlinux-$(1)$(3).bin.lzma)
endef
# $(1), lowercase board name
# $(2), DTS filename without .dts extension
# $(3), ih_name field of uImage header
# $(4), optional filename suffix, e.g. "-initramfs"
define MkImageLzmaDtb
$(call PatchKernelLzmaDtb,$(1),$(2),$(4))
$(call MkImage,lzma,$(KDIR)/vmlinux-$(1)$(4).bin.lzma,$(KDIR)/vmlinux-$(1)$(4).uImage,$(3))
endef
# $(1), Rootfs type, e.g. squashfs
# $(2), lowercase board name
# $(3), DTS filename without .dts extension
# $(4), maximum size of sysupgrade image
# $(5), uImage header's ih_name field
define BuildFirmware/OF
$(call MkImageLzmaDtb,$(2),$(3),$(5))
$(call MkImageSysupgrade/$(1),$(1),$(2),$(4),$(6))
endef
define BuildFirmware/OF/tplink
$(call PatchKernelLzmaDtb,$(1),$(2),$(4))
$(call MkImageTpl/$(1),$(1),$(2),$(4),$(5))
endef
define BuildFirmware/OF/tplink/initramfs
$(call PatchKernelLzmaDtb,$(2),$(3),-initramfs)
$(call MkImageTpl/$(1),$(1),$(2),$(4),$(5))
endef
# $(1), squashfs/initramfs
# $(2), lowercase board name
# $(3), DTS filename without .dts extension
# $(4), ih_name field of uImage header
define BuildFirmware/OF/initramfs
$(call MkImageLzmaDtb,$(2),$(3),$(4),-initramfs)
$(CP) $(KDIR)/vmlinux-$(2)-initramfs.uImage $(call imgname,$(1),$(2))-uImage.bin
endef
# Build images for default ralink layout for 4MB flash
# kernel + roots = 0x3b0000
# $(1) = squashfs/initramfs
# $(2) = lowercase board name
# $(3) = dts file
ralink_default_fw_size_4M=3866624
BuildFirmware/Default4M/squashfs=$(call BuildFirmware/OF,$(1),$(2),$(3),$(ralink_default_fw_size_4M),$(4))
BuildFirmware/Default4M/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3),$(4))
# Build images for default ralink layout for 8MB flash
# kernel + roots = 0x7b0000
# $(1) = squashfs/initramfs
# $(2) = lowercase board name
# $(3) = dts file
# $(4) = uImage header name field
ralink_default_fw_size_8M=8060928
BuildFirmware/Default8M/squashfs=$(call BuildFirmware/OF,$(1),$(2),$(3),$(ralink_default_fw_size_8M),$(4))
BuildFirmware/Default8M/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3),$(4))
BuildFirmware/Tplink/squashfs=$(call BuildFirmware/OF/tplink,$(1),$(2),$(3),$(4))
BuildFirmware/Tplink/initramfs=$(call BuildFirmware/OF/tplink/initramfs,$(1),$(2),$(3),$(4))
ralink_default_fw_size_16M=16121856
BuildFirmware/Default16M/squashfs=$(call BuildFirmware/OF,$(1),$(2),$(3),$(ralink_default_fw_size_16M),$(4))
BuildFirmware/Default16M/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3),$(4))
ralink_default_fw_size_32M=33226752
BuildFirmware/Default32M/squashfs=$(call BuildFirmware/OF,$(1),$(2),$(3),$(ralink_default_fw_size_32M),$(4))
BuildFirmware/Default32M/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3),$(4))
# Build images for a custom sized flash layout
# $(1) = squashfs/initramfs
# $(2) = lowercase board name
# $(3) = dts file
# $(4) = kernel + rootfs size
BuildFirmware/CustomFlash/squashfs=$(call BuildFirmware/OF,$(1),$(2),$(3),$(4),$(5),$(6))
BuildFirmware/CustomFlash/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
# wrappers for boards that have 4MB and 8MB versions
define BuildFirmware/DefaultDualSize/squashfs
$(call BuildFirmware/Default4M/$(1),$(1),$(2)-4M,$(3)-4M)
$(call BuildFirmware/Default8M/$(1),$(1),$(2)-8M,$(3)-8M)
endef
define BuildFirmware/DefaultDualSize/initramfs
$(call BuildFirmware/OF/initramfs,$(1),$(2)-4M,$(3)-4M)
$(call BuildFirmware/OF/initramfs,$(1),$(2)-8M,$(3)-8M)
endef
# Some boards need a special header inside the uImage to make them bootable
define BuildFirmware/CustomFlashFactory/squashfs
$(call BuildFirmware/CustomFlash/$(1),$(1),$(2),$(3),$(4))
$(call BuildFirmware/CustomFlash/$(1),$(1),$(2),$(3),$(4),$(5),$(6))
endef
BuildFirmware/CustomFlashFactory/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
# sign an image to make it work with edimax tftp recovery
define BuildFirmware/Edimax/squashfs
$(call BuildFirmware/OF,$(1),$(2),$(3),$(4))
if [ -e "$(call sysupname,$(1),$(2))" ]; then \
mkedimaximg -i $(call sysupname,$(1),$(2)) \
-o $(call imgname,$(1),$(2))-factory.bin \
-s $(5) -m $(6) -f $(7) -S $(8); \
fi
endef
BuildFirmware/Edimax/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
# build Seama header images
define BuildFirmware/Seama/squashfs
$(call MkImageLzmaDtb,$(2),$(3),$(5))
$(eval output_name=$(IMG_PREFIX)-$(2)-$(1)-sysupgrade.bin)
cat $(KDIR)/vmlinux-$(2).bin.lzma $(KDIR)/root.$(1) > $(KDIR)/img_$(2).$(1).tmp
if [ `stat -c%s "$(KDIR)/img_$(2).$(1).tmp"` -gt $$$$(($(5) - 64)) ]; then \
echo "Warning: $(KDIR)/img_$(2).$(1).tmp is too big" >&2; \
else \
dd if=$(KDIR)/vmlinux-$(2).bin.lzma of=$(KDIR)/vmlinux-$(2).bin.lzma.padded bs=64k conv=sync; \
( \
dd if=$(KDIR)/vmlinux-$(2).bin.lzma.padded bs=1 count=`expr \`stat -c%s $(KDIR)/vmlinux-$(2).bin.lzma.padded\` - 64`; \
dd if=$(KDIR)/root.$(1) bs=64k conv=sync; \
) > $(KDIR)/vmlinux-$(2).tmp; \
$(STAGING_DIR_HOST)/bin/seama \
-i $(KDIR)/vmlinux-$(2).tmp \
-m "dev=/dev/mtdblock/2" -m "type=firmware"; \
$(STAGING_DIR_HOST)/bin/seama \
-s $(call imgname,$(1),$(2))-factory.bin \
-m "signature=$(4)" \
-i $(KDIR)/vmlinux-$(2).tmp.seama; \
dd if=$(KDIR)/vmlinux-$(2).bin.lzma.padded bs=1 count=`expr \`stat -c%s $(KDIR)/vmlinux-$(2).bin.lzma.padded\` - 64` of=$(KDIR)/vmlinux-$(2)-sysupgrade.tmp; \
$(STAGING_DIR_HOST)/bin/seama \
-i $(KDIR)/vmlinux-$(2)-sysupgrade.tmp \
-m "dev=/dev/mtdblock/2" -m "type=firmware"; \
( \
dd if=$(KDIR)/vmlinux-$(2)-sysupgrade.tmp.seama; \
dd if=$(KDIR)/root.$(1) bs=64k conv=sync; \
) > $(BIN_DIR)/$(output_name); \
fi
endef
BuildFirmware/Seama/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
# sign Buffalo images
define BuildFirmware/Buffalo
if [ -e "$(call sysupname,$(1),$(2))" ]; then \
buffalo-enc -p $(3) -v 1.76 \
-i $(KDIR)/vmlinux-$(2).uImage \
-o $(KDIR)/vmlinux-$(2).uImage.enc; \
buffalo-enc -p $(3) -v 1.76 \
-i $(KDIR)/root.$(1) \
-o $(KDIR)/root.$(2).enc; \
buffalo-tag -b $(3) -p $(3) -a ram -v 1.76 -m 1.01 \
-l mlang8 -f 1 -r EU \
-i $(KDIR)/vmlinux-$(2).uImage.enc \
-i $(KDIR)/root.$(2).enc \
-o $(call imgname,$(1),$(2))-factory-EU.bin; \
fi
endef
# sign trednet / UMedia images
define BuildFirmware/UMedia/squashfs
$(call BuildFirmware/Default8M/$(1),$(1),$(2),$(3))
if [ -e "$(call sysupname,$(1),$(2))" ]; then \
fix-u-media-header -T 0x46 -B $(4) \
-i $(call sysupname,$(1),$(2)) \
-o $(call imgname,$(1),$(2))-factory.bin; \
fi
endef
BuildFirmware/UMedia/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
# sign dap 1350 based images
dap1350_mtd_size=7667712
define BuildFirmware/dap1350/squashfs
$(call BuildFirmware/CustomFlash/$(1),$(1),$(2),$(3),$(dap1350_mtd_size))
-mkdapimg -s $(4) \
-i $(call sysupname,$(1),$(2)) \
-o $(call imgname,$(1),$(2))-factory.bin
endef
BuildFirmware/dap1350/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
# Sign Poray images
define BuildFirmware/Poray4M/squashfs
$(call BuildFirmware/Default4M/$(1),$(1),$(2),$(3))
if [ -e "$(call sysupname,$(1),$(2))" ]; then \
mkporayfw -B $(3) -F 4M \
-f $(call sysupname,$(1),$(2)) \
-o $(call imgname,$(1),$(2))-factory.bin; \
fi
endef
BuildFirmware/Poray4M/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
define BuildFirmware/Poray8M/squashfs
$(call BuildFirmware/Default8M/$(1),$(1),$(2),$(3))
if [ -e "$(call sysupname,$(1),$(2))" ]; then \
mkporayfw -B $(3) -F 8M \
-f $(call sysupname,$(1),$(2)) \
-o $(call imgname,$(1),$(2))-factory.bin; \
fi
endef
BuildFirmware/Poray8M/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
define BuildFirmware/PorayDualSize/squashfs
$(call BuildFirmware/DefaultDualSize/$(1),$(1),$(2),$(3))
if [ -e "$(call sysupname,$(1),$(2)-4M)" ]; then \
mkporayfw -B $(3) -F 4M \
-f $(call sysupname,$(1),$(2)-4M) \
-o $(call imgname,$(1),$(2)-4M)-factory.bin; \
fi
if [ -e "$(call sysupname,$(1),$(2)-8M)" ]; then \
mkporayfw -B $(3) -F 8M \
-f $(call sysupname,$(1),$(2)-8M) \
-o $(call imgname,$(1),$(2)-8M)-factory.bin; \
fi
endef
BuildFirmware/PorayDualSize/initramfs=$(call BuildFirmware/DefaultDualSize/initramfs,$(1),$(2),$(3))
define BuildFirmware/Gemtek/squashfs
$(call BuildFirmware/Default4M/$(1),$(1),$(2),$(3))
if [ -e "$(call sysupname,$(1),$(2))" ]; then \
mkheader_gemtek "$(call sysupname,$(1),$(2))" \
"$(call imgname,$(1),$(2))-factory.bin" $(2) || \
rm -f "$(call imgname,$(1),$(2))-factory.bin"; \
fi
endef
BuildFirmware/Gemtek/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
# Airlink101 AR670W -- LZMA without uImage header
define BuildFirmware/AR670W/squashfs
$(call PatchKernelLzmaDtb,$(2),$(3),$(5))
$(eval output_name=$(IMG_PREFIX)-$(2)-$(1)-$(if $(4),$(4),sysupgrade).bin)
$(eval factory_name=$(IMG_PREFIX)-$(2)-$(1)-factory.bin)
( dd if=$(KDIR)/vmlinux-$(2).bin.lzma bs=65536 \
conv=sync; dd if=$(KDIR)/root.$(1) ) > $(KDIR)/$(output_name)
$(call prepare_generic_squashfs,$(KDIR)/$(output_name))
if [ `stat -c%s "$(KDIR)/$(output_name)"` \
-gt $(ralink_default_fw_size_4M) ]; then \
echo "Warning: $(KDIR)/$(output_name) is too big" >&2; \
else \
mkwrgimg -i $(KDIR)/$(output_name) \
-d "/dev/mtdblock/2" \
-s "wrgn16a_airlink_ar670w" \
-o $(BIN_DIR)/$(factory_name); \
$(CP) $(KDIR)/$(output_name) $(BIN_DIR)/$(output_name); \
fi
endef
#
# RT288X Profiles
#
Image/Build/Profile/AR670W=$(call BuildFirmware/AR670W/$(1),$(1),ar670w,AR670W)
Image/Build/Profile/AR725W=$(call BuildFirmware/Gemtek/$(1),$(1),ar725w,AR725W)
# 0x790000
belkin_f5d8235v1_mtd_size=7929856
Image/Build/Profile/F5D8235V1=$(call BuildFirmware/CustomFlash/$(1),$(1),f5d8235v1,F5D8235_V1,$(belkin_f5d8235v1_mtd_size))
Image/Build/Profile/RTN15=$(call BuildFirmware/Default4M/$(1),$(1),rt-n15,RT-N15)
Image/Build/Profile/V11STFE=$(call BuildFirmware/Default4M/$(1),$(1),v11st-fe,V11STFE)
Image/Build/Profile/WLITX4AG300N=$(call BuildFirmware/Default4M/$(1),$(1),wli-tx4-ag300n,WLI-TX4-AG300N)
Image/Build/Profile/WZRAGL300NH=$(call BuildFirmware/Default4M/$(1),$(1),wzr-agl300nh,WZR-AGL300NH)
ifeq ($(SUBTARGET),rt288x)
define Image/Build/Profile/Default
$(call Image/Build/Profile/AR670W,$(1))
$(call Image/Build/Profile/AR725W,$(1))
$(call Image/Build/Profile/F5D8235V1,$(1))
$(call Image/Build/Profile/RTN15,$(1))
$(call Image/Build/Profile/V11STFE,$(1))
$(call Image/Build/Profile/WLITX4AG300N,$(1))
$(call Image/Build/Profile/WZRAGL300NH,$(1))
endef
endif
#
# RT305X Profiles
#
Image/Build/Profile/DIR610A1=$(call BuildFirmware/Seama/$(1),$(1),dir-610-a1,DIR-610-A1,wrgn59_dlob.hans_dir610,$(ralink_default_fw_size_4M))
edimax_3g6200n_mtd_size=3735552
Image/Build/Profile/3G6200N=$(call BuildFirmware/Edimax/$(1),$(1),3g-6200n,3G-6200N,$(edimax_3g6200n_mtd_size),CSYS,3G62,0x50000,0xc0000)
Image/Build/Profile/3G6200NL=$(call BuildFirmware/Edimax/$(1),$(1),3g-6200nl,3G-6200NL,$(edimax_3g6200n_mtd_size),CSYS,3G62,0x50000,0xc0000)
Image/Build/Profile/3G300M=$(call BuildFirmware/CustomFlashFactory/$(1),$(1),3g300m,3G300M,$(ralink_default_fw_size_4M),3G150M_SPI Kernel Image,factory)
Image/Build/Profile/A5-V11=$(call BuildFirmware/Poray4M/$(1),$(1),a5-v11,A5-V11)
Image/Build/Profile/AIR3GII=$(call BuildFirmware/Default4M/$(1),$(1),air3gii,AIR3GII)
define BuildFirmware/UIMAGE_8M
$(call MkCombineduImage,$(1),$(2),$(call mkcmdline,$(3),$(4),$(5)) $(call mkmtd/$(6),$(mtdlayout_8M)),$(kernel_size_8M),$(rootfs_size_8M),$(7))
endef
define Image/Build/Profile/ALL02393G
$(call Image/Build/Template/$(image_type)/$(1),UIMAGE_8M,all0239-3g,ALL0239-3G,ttyS1,57600,phys)
endef
Image/Build/Profile/ALL0256N=$(call BuildFirmware/DefaultDualSize/$(1),$(1),all0256n,ALL0256N)
allnet_all5002_mtd_size=33226752
Image/Build/Profile/ALL5002=$(call BuildFirmware/CustomFlash/$(1),$(1),all5002,ALL5002,$(allnet_all5002_mtd_size))
Image/Build/Profile/ALL5003=$(call BuildFirmware/CustomFlash/$(1),$(1),all5003,ALL5003,$(allnet_all5002_mtd_size))
argus_atp52b_mtd_size=7995392
Image/Build/Profile/ATP-52B=$(call BuildFirmware/CustomFlash/$(1),$(1),atp-52b,ATP-52B,$(argus_atp52b_mtd_size))
asl26555_8mb_mtd_size=7929856
asl26555_16mb_mtd_size=16252928
define BuildFirmware/ASL26555/squashfs
$(call BuildFirmware/CustomFlash/$(1),$(1),$(2)-8M,$(3)-8M,$(asl26555_8mb_mtd_size))
$(call BuildFirmware/CustomFlash/$(1),$(1),$(2)-16M,$(3)-16M,$(asl26555_16mb_mtd_size))
endef
define BuildFirmware/ASL26555/initramfs
$(call BuildFirmware/OF/initramfs,$(1),$(2)-8M,$(3)-8M)
$(call BuildFirmware/OF/initramfs,$(1),$(2)-16M,$(3)-16M)
endef
Image/Build/Profile/ASL26555=$(call BuildFirmware/ASL26555/$(1),$(1),asl26555,ASL26555)
Image/Build/Profile/AWM002EVB=$(call BuildFirmware/DefaultDualSize/$(1),$(1),awm002-evb,AWM002-EVB)
Image/Build/Profile/AWM003EVB=$(call BuildFirmware/Default8M/$(1),$(1),awm003-evb,AWM003-EVB)
Image/Build/Profile/AWAPN2403=$(call BuildFirmware/Default4M/$(1),$(1),awmapn2403,AWAPN2403)
Image/Build/Profile/BC2=$(call BuildFirmware/Default8M/$(1),$(1),bc2,BC2)
broadway_mtd_size=7929856
Image/Build/Profile/BROADWAY=$(call BuildFirmware/CustomFlashFactory/$(1),$(1),broadway,BROADWAY,$(broadway_mtd_size),Broadway Kernel Image,factory)
Image/Build/Profile/CARAMBOLA=$(call BuildFirmware/Default8M/$(1),$(1),carambola,CARAMBOLA)
Image/Build/Profile/D105=$(call BuildFirmware/Default4M/$(1),$(1),d105,D105)
define BuildFirmware/DIR300B1/squashfs
$(call BuildFirmware/Default4M/$(1),$(1),$(2),$(3))
-mkwrgimg -s $(4) -d /dev/mtdblock/2 \
-i $(call sysupname,$(1),$(2)) \
-o $(call imgname,$(1),$(2))-factory.bin
endef
BuildFirmware/DIR300B1/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
Image/Build/Profile/DIR-300-B1=$(call BuildFirmware/DIR300B1/$(1),$(1),dir-300-b1,DIR-300-B1,wrgn23_dlwbr_dir300b)
Image/Build/Profile/DIR-600-B1=$(call BuildFirmware/DIR300B1/$(1),$(1),dir-600-b1,DIR-600-B1,wrgn23_dlwbr_dir600b)
Image/Build/Profile/DIR-600-B2=$(call BuildFirmware/DIR300B1/$(1),$(1),dir-600-b2,DIR-600-B2,wrgn23_dlwbr_dir600b)
Image/Build/Profile/DIR-615-D=$(call BuildFirmware/DIR300B1/$(1),$(1),dir-615-d,DIR-615-D,wrgn23_dlwbr_dir615d)
Image/Build/Profile/DIR-620-A1=$(call BuildFirmware/Default8M/$(1),$(1),dir-620-a1,DIR-620-A1)
Image/Build/Profile/DIR-620-D1=$(call BuildFirmware/Default8M/$(1),$(1),dir-620-d1,DIR-620-D1)
define BuildFirmware/DIR615H1/squashfs
$(call BuildFirmware/Default4M/$(1),$(1),dir-615-h1,DIR-615-H1)
-mksenaofw -e $(call sysupname,$(1),dir-615-h1) \
-o $(call imgname,$(1),dir-615-h1)-factory.bin \
-r 0x218 -p 0x30 -t 3
endef
BuildFirmware/DIR615H1/initramfs=$(call BuildFirmware/OF/initramfs,$(1),dir-615-h1,DIR-615-H1)
Image/Build/Profile/DIR615H1=$(call BuildFirmware/DIR615H1/$(1),$(1))
Image/Build/Profile/DAP1350=$(call BuildFirmware/dap1350/$(1),$(1),dap-1350,DAP-1350,RT3052-AP-DAP1350-3)
Image/Build/Profile/DAP1350WW=$(call BuildFirmware/dap1350/$(1),$(1),dap-1350WW,DAP-1350,RT3052-AP-DAP1350WW-3)
define BuildFirmware/DCS930/squashfs
$(call BuildFirmware/Default4M/squashfs,squashfs,$(2),$(3))
dd if=$(KDIR)/vmlinux-$(2).bin.lzma of=$(KDIR)/image.$(2).combined bs=1048512 count=1 conv=sync
cat $(KDIR)/root.squashfs >> $(KDIR)/image.$(2).combined
$(call MkImage,lzma,$(KDIR)/image.$(2).combined,$(KDIR)/image.$(2))
$(call prepare_generic_squashfs,$(KDIR)/image.$(2))
if [ `stat -c%s "$(KDIR)/image.$(2)"` -gt $(ralink_default_fw_size_4M) ]; then \
echo "Warning: $(KDIR)/image.$(2) is too big" >&2; \
else \
dd if=$(KDIR)/image.$(2) of=$(KDIR)/dcs.tmp bs=64K count=5 conv=sync ;\
cat $(KDIR)/image.$(2) >> $(KDIR)/dcs.tmp ; \
dd if=$(KDIR)/dcs.tmp of=$(call imgname,$(1),$(2))-factory.bin bs=4096k count=1 conv=sync ;\
$(STAGING_DIR_HOST)/bin/mkdcs932 $(call imgname,$(1),$(2))-factory.bin ; \
fi
endef
BuildFirmware/DCS930/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
Image/Build/Profile/DCS930=$(call BuildFirmware/DCS930/$(1),$(1),dcs-930,DCS-930)
Image/Build/Profile/DCS930LB1=$(call BuildFirmware/DCS930/$(1),$(1),dcs-930l-b1,DCS-930L-B1)
Image/Build/Profile/ESR-9753=$(call BuildFirmware/Default4M/$(1),$(1),esr-9753,ESR-9753)
Image/Build/Profile/HW550-3G=$(call BuildFirmware/Default8M/$(1),$(1),hw550-3g,HW550-3G)
belkin_f5d8235v2_mtd_size=7929856
Image/Build/Profile/F5D8235V2=$(call BuildFirmware/CustomFlash/$(1),$(1),f5d8235v2,F5D8235_V2,$(belkin_f5d8235v2_mtd_size))
# 0x770000
belkin_f7c027_mtd_size=7798784
Image/Build/Profile/F7C027=$(call BuildFirmware/CustomFlash/$(1),$(1),f7c027,F7C027,$(belkin_f7c027_mtd_size))
Image/Build/Profile/FONERA20N=$(call BuildFirmware/Edimax/$(1),$(1),fonera20n,FONERA20N,$(ralink_default_fw_size_8M),RSDK,NL1T,0x50000,0xc0000)
Image/Build/Profile/RT-N13U=$(call BuildFirmware/Default8M/$(1),$(1),rt-n13u,RT-N13U)
#Image/Build/Profile/HG255D=$(call BuildFirmware/Default16M/$(1),$(1),hg255d,HG255D)
Image/Build/Profile/FREESTATION5=$(call BuildFirmware/Default8M/$(1),$(1),freestation5,FREESTATION5)
Image/Build/Profile/IP2202=$(call BuildFirmware/Default8M/$(1),$(1),ip2202,IP2202)
BuildFirmware/HLKRM04/squashfs=$(call BuildFirmware/Default4M/squashfs,$(1),$(2),$(3),$(4))
define BuildFirmware/HLKRM04/initramfs
$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3),$(4))
mkhilinkfw -e -i$(call imgname,$(1),$(2))-uImage.bin -o $(call imgname,$(1),$(2))-factory.bin;
endef
Image/Build/Profile/HLKRM04=$(call BuildFirmware/HLKRM04/$(1),$(1),hlk-rm04,HLKRM04,HLK-RM02)
Image/Build/Profile/HT-TM02=$(call BuildFirmware/Default8M/$(1),$(1),ht-tm02,HT-TM02)
Image/Build/Profile/M3=$(call BuildFirmware/Poray4M/$(1),$(1),m3,M3)
Image/Build/Profile/M4=$(call BuildFirmware/PorayDualSize/$(1),$(1),m4,M4)
Image/Build/Profile/MOFI3500-3GN=$(call BuildFirmware/Default8M/$(1),$(1),mofi3500-3gn,MOFI3500-3GN)
# Kernel name should be "Linux Kernel Image" to make the OpenWrt image installable from factory Web UI
Image/Build/Profile/3G150B=$(call BuildFirmware/Default4M/$(1),$(1),3g150b,3G150B,Linux Kernel Image)
Image/Build/Profile/MR102N=$(call BuildFirmware/Default8M/$(1),$(1),mr-102n,MR-102N)
Image/Build/Profile/MPRA1=$(call BuildFirmware/Default4M/$(1),$(1),mpr-a1,MPRA1,Linux Kernel Image)
Image/Build/Profile/MPRA2=$(call BuildFirmware/Default8M/$(1),$(1),mpr-a2,MPRA2,Linux Kernel Image)
Image/Build/Profile/DIR-300-B7=$(call BuildFirmware/Default4M/$(1),$(1),dir-300-b7,DIR-300-B7)
Image/Build/Profile/DIR-320-B1=$(call BuildFirmware/Default8M/$(1),$(1),dir-320-b1,DIR-320-B1)
Image/Build/Profile/NBG-419N=$(call BuildFirmware/Default4M/$(1),$(1),nbg-419n,NBG-419N)
Image/Build/Profile/MZKW300NH2=$(call BuildFirmware/Edimax/$(1),$(1),mzk-w300nh2,MZK-W300NH2,$(mzkw300nh2_mtd_size),CSYS,RN52,0x50000,0xc0000)
Image/Build/Profile/NCS601W=$(call BuildFirmware/Default8M/$(1),$(1),ncs601W,NCS601W)
nw718_mtd_size=3801088
Image/Build/Profile/NW718=$(call BuildFirmware/CustomFlashFactory/$(1),$(1),nw718m,NW718,$(nw718_mtd_size),ARA1B4NCRNW718;1,factory)
Image/Build/Profile/M2M=$(call BuildFirmware/Default8M/$(1),$(1),m2m,M2M,Linux Kernel Image)
Image/Build/Profile/MINIEMBPLUG=$(call BuildFirmware/Default8M/$(1),$(1),miniembplug,MINIEMBPLUG)
Image/Build/Profile/MINIEMBWIFI=$(call BuildFirmware/Default8M/$(1),$(1),miniembwifi,MINIEMBWIFI)
Image/Build/Profile/PSR-680W=$(call BuildFirmware/Default4M/$(1),$(1),psr-680w,PSR-680W)
Image/Build/Profile/PWH2004=$(call BuildFirmware/Default8M/$(1),$(1),pwh2004,PWH2004)
Image/Build/Profile/PX-4885=$(call BuildFirmware/DefaultDualSize/$(1),$(1),px-4885,PX-4885)
Image/Build/Profile/RT5350F-OLINUXINO=$(call BuildFirmware/Default8M/$(1),$(1),rt5350f-olinuxino,RT5350F-OLINUXINO)
Image/Build/Profile/RT5350F-OLINUXINO-EVB=$(call BuildFirmware/Default8M/$(1),$(1),rt5350f-olinuxino-evb,RT5350F-OLINUXINO-EVB)
Image/Build/Profile/RTG32B1=$(call BuildFirmware/Default4M/$(1),$(1),rt-g32-b1,RT-G32-B1)
Image/Build/Profile/RTN10PLUS=$(call BuildFirmware/Default4M/$(1),$(1),rt-n10-plus,RT-N10-PLUS)
Image/Build/Profile/RUT5XX=$(call BuildFirmware/Default8M/$(1),$(1),rut5xx,RUT5XX)
Image/Build/Profile/SL-R7205=$(call BuildFirmware/Default4M/$(1),$(1),sl-r7205,SL-R7205)
Image/Build/Profile/V22RW-2X2=$(call BuildFirmware/Default4M/$(1),$(1),v22rw-2x2,V22RW-2X2)
vocore_8mb_mtd_size=8060928
vocore_16mb_mtd_size=16449536
define BuildFirmware/VOCORE/squashfs
$(call BuildFirmware/CustomFlash/$(1),$(1),$(2)-8M,$(3)-8M,$(vocore_8mb_mtd_size))
$(call BuildFirmware/CustomFlash/$(1),$(1),$(2)-16M,$(3)-16M,$(vocore_16mb_mtd_size))
endef
define BuildFirmware/VOCORE/initramfs
$(call BuildFirmware/OF/initramfs,$(1),$(2)-8M,$(3)-8M)
$(call BuildFirmware/OF/initramfs,$(1),$(2)-16M,$(3)-16M)
endef
Image/Build/Profile/VOCORE=$(call BuildFirmware/VOCORE/$(1),$(1),vocore,VOCORE)
Image/Build/Profile/W150M=$(call BuildFirmware/CustomFlashFactory/$(1),$(1),w150m,W150M,$(ralink_default_fw_size_4M),W150M Kernel Image,factory)
Image/Build/Profile/W306R_V20=$(call BuildFirmware/CustomFlashFactory/$(1),$(1),w306r-v20,W306R_V20,$(ralink_default_fw_size_4M),linkn Kernel Image,factory)
Image/Build/Profile/W502U=$(call BuildFirmware/Default8M/$(1),$(1),w502u,W502U)
Image/Build/Profile/WCR150GN=$(call BuildFirmware/Default4M/$(1),$(1),wcr150gn,WCR150GN)
Image/Build/Profile/MZK-DP150N=$(call BuildFirmware/Default4M/$(1),$(1),mzk-dp150n,MZK-DP150N)
buffalo_whrg300n_mtd_size=3801088
define BuildFirmware/WHRG300N/squashfs
$(call BuildFirmware/Default4M/$(1),$(1),whr-g300n,WHR-G300N)
# the following line has a bad argument 3 ... the old Makefile was already broken
$(call BuildFirmware/Buffalo,$(1),whr-g300n,whr-g300n)
if [ -e "$(call sysupname,$(1),$(2))" ]; then \
( \
echo -n -e "# Airstation FirmWare\nrun u_fw\nreset\n\n" | \
dd bs=512 count=1 conv=sync; \
dd if=$(call sysupname,$(1),whr-g300n); \
) > $(KDIR)/whr-g300n-tftp.tmp && \
buffalo-tftp -i $(KDIR)/whr-g300n-tftp.tmp \
-o $(call imgname,$(1),whr-g300n)-tftp.bin; \
fi
endef
BuildFirmware/WHRG300N/initramfs=$(call BuildFirmware/OF/initramfs,$(1),whr-g300n,WHR-G300N)
Image/Build/Profile/WHRG300N=$(call BuildFirmware/WHRG300N/$(1),$(1))
Image/Build/Profile/WIZARD8800=$(call BuildFirmware/Default8M/$(1),$(1),wizard-8800,WIZARD8800,Linux Kernel Image)
Image/Build/Profile/WIZFI630A=$(call BuildFirmware/Default16M/$(1),$(1),wizfi630a,WIZFI630A)
Image/Build/Profile/WL-330N=$(call BuildFirmware/Default4M/$(1),$(1),wl-330n,WL-330N)
Image/Build/Profile/WL-330N3G=$(call BuildFirmware/Default4M/$(1),$(1),wl-330n3g,WL-330N3G)
kernel_size_wl341v3=917504
rootfs_size_wl341v3=2949120
define BuildFirmware/WL-341V3/squashfs
$(call BuildFirmware/Default4M/$(1),$(1),wl-341v3,WL-341V3)
# This code looks broken and really needs to be converted to C
if [ -e "$(call sysupname,$(1),$(2))" ]; then \
( \
dd if=/dev/zero bs=195936 count=1; \
echo "1.01"; \
dd if=/dev/zero bs=581 count=1; \
echo -n -e "\x73\x45\x72\x43\x6F\x4D\x6D\x00\x01\x00\x00\x59\x4E\x37\x95\x58\x10\x00\x20\x00\x28\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x11\x03\x00\x00\x80\x00\x00\x00\x00\x03\x00\x00\x10\x12\x00\x00\x00\x10\x73\x45\x72\x43\x6F\x4D\x6D"; \
dd if=/dev/zero bs=65552 count=1; \
dd if=$(KDIR)/vmlinux-$(2).uImage bs=$(kernel_size_wl341v3) conv=sync; \
dd if=$(KDIR)/root.$(1) bs=64k conv=sync; \
dd if=/dev/zero bs=`expr 4194304 - 262144 - 16 - $(kernel_size_wl341v3) - \( \( \( \`stat -c%s $(KDIR)/root.$(1)\` / 65536 \) + 1 \) \* 65536 \)` count=1; \
echo -n -e "\x11\x03\x80\x00\x10\x12\x90\xF7\x65\x52\x63\x4F\x6D\x4D\x00\x00"; \
) > $(call imgname,$(1),$(2))-factory.bin; \
fi
endef
BuildFirmware/WL-341V3/initramfs=$(call BuildFirmware/OF/initramfs,$(1),wl-341v3,WL-341V3)
Image/Build/Profile/WL-341V3=$(call BuildFirmware/WL-341V3/$(1),$(1))
Image/Build/Profile/WL-351=$(call BuildFirmware/Default4M/$(1),$(1),wl-351,WL-351)
define BuildFirmware/WNCE2001/squashfs
$(call BuildFirmware/Default4M/$(1),$(1),$(2),$(3))
-mkdapimg -s RT3052-AP-WNCE2001-3 -r WW -v 1.0.0.99 \
-i $(call sysupname,$(1),$(2)) \
-o $(call imgname,$(1),$(2))-factory-worldwide.bin
-mkdapimg -s RT3052-AP-WNCE2001-3 -r NA -v 1.0.0.99 \
-i $(call sysupname,$(1),$(2)) \
-o $(call imgname,$(1),$(2))-factory-northamerica.bin
endef
BuildFirmware/WNCE2001/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3))
Image/Build/Profile/WNCE2001=$(call BuildFirmware/WNCE2001/$(1),$(1),wnce2001,WNCE2001)
Image/Build/Profile/WR512-3GN=$(call BuildFirmware/DefaultDualSize/$(1),$(1),wr512-3ng,WR512-3GN)
Image/Build/Profile/WT1520=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt1520,WT1520)
Image/Build/Profile/UR-326N4G=$(call BuildFirmware/Default4M/$(1),$(1),ur-326n4g,UR-326N4G)
Image/Build/Profile/UR-336UN=$(call BuildFirmware/Default8M/$(1),$(1),ur-336un,UR-336UN)
Image/Build/Profile/WR6202=$(call BuildFirmware/Default8M/$(1),$(1),wr6202,WR6202)
Image/Build/Profile/X5=$(call BuildFirmware/Poray8M/$(1),$(1),x5,X5)
Image/Build/Profile/X8=$(call BuildFirmware/Poray8M/$(1),$(1),x8,X8)
Image/Build/Profile/XDXRN502J=$(call BuildFirmware/Default4M/$(1),$(1),xdxrn502j,XDXRN502J)
ifeq ($(SUBTARGET),rt305x)
define Image/Build/Profile/Default
$(call Image/Build/Profile/3G6200N,$(1))
$(call Image/Build/Profile/3G6200NL,$(1))
$(call Image/Build/Profile/3G150B,$(1))
$(call Image/Build/Profile/3G300M,$(1))
$(call Image/Build/Profile/A5-V11,$(1))
$(call Image/Build/Profile/AIR3GII,$(1))
$(call Image/Build/Profile/ALL02393G,$(1))
$(call Image/Build/Profile/ALL0256N,$(1))
$(call Image/Build/Profile/ALL5002,$(1))
$(call Image/Build/Profile/ALL5003,$(1))
$(call Image/Build/Profile/ASL26555,$(1))
$(call Image/Build/Profile/ATP-52B,$(1))
$(call Image/Build/Profile/AWM002EVB,$(1))
$(call Image/Build/Profile/AWAPN2403,$(1))
$(call Image/Build/Profile/BC2,$(1))
$(call Image/Build/Profile/BROADWAY,$(1))
$(call Image/Build/Profile/CARAMBOLA,$(1))
$(call Image/Build/Profile/D105,$(1))
$(call Image/Build/Profile/DIR-300-B1,$(1))
$(call Image/Build/Profile/DIR-600-B1,$(1))
$(call Image/Build/Profile/DIR-300-B7,$(1))
$(call Image/Build/Profile/DIR-320-B1,$(1))
$(call Image/Build/Profile/DIR-600-B2,$(1))
$(call Image/Build/Profile/DIR610A1,$(1))
$(call Image/Build/Profile/DIR-615-D,$(1))
$(call Image/Build/Profile/DIR-620-A1,$(1))
$(call Image/Build/Profile/DIR-620-D1,$(1))
$(call Image/Build/Profile/DIR615H1,$(1))
$(call Image/Build/Profile/DAP1350,$(1))
$(call Image/Build/Profile/DAP1350WW,$(1))
$(call Image/Build/Profile/DCS930,$(1))
$(call Image/Build/Profile/DCS930LB1,$(1))
$(call Image/Build/Profile/ESR-9753,$(1))
$(call Image/Build/Profile/F7C027,$(1))
$(call Image/Build/Profile/F5D8235V2,$(1))
$(call Image/Build/Profile/FONERA20N,$(1))
$(call Image/Build/Profile/FREESTATION5,$(1))
# $(call Image/Build/Profile/HG255D,$(1))
$(call Image/Build/Profile/HLKRM04,$(1))
$(call Image/Build/Profile/HT-TM02,$(1))
$(call Image/Build/Profile/HW550-3G,$(1))
$(call Image/Build/Profile/IP2202,$(1))
$(call Image/Build/Profile/M2M,$(1))
$(call Image/Build/Profile/M3,$(1))
$(call Image/Build/Profile/M4,$(1))
$(call Image/Build/Profile/MOFI3500-3GN,$(1))
$(call Image/Build/Profile/MR102N,$(1))
$(call Image/Build/Profile/MPRA1,$(1))
$(call Image/Build/Profile/MPRA2,$(1))
$(call Image/Build/Profile/MZKW300NH2,$(1))
$(call Image/Build/Profile/NBG-419N,$(1))
$(call Image/Build/Profile/NCS601W,$(1))
$(call Image/Build/Profile/NW718,$(1))
$(call Image/Build/Profile/MINIEMBWIFI,$(1))
$(call Image/Build/Profile/MINIEMBPLUG,$(1))
$(call Image/Build/Profile/PSR-680W,$(1))
$(call Image/Build/Profile/PWH2004,$(1))
$(call Image/Build/Profile/PX-4885,$(1))
$(call Image/Build/Profile/RT5350F-OLINUXINO,$(1))
$(call Image/Build/Profile/RT5350F-OLINUXINO-EVB,$(1))
$(call Image/Build/Profile/RTG32B1,$(1))
$(call Image/Build/Profile/RTN10PLUS,$(1))
$(call Image/Build/Profile/RT-N13U,$(1))
$(call Image/Build/Profile/RUT5XX,$(1))
$(call Image/Build/Profile/SL-R7205,$(1))
$(call Image/Build/Profile/UR-326N4G,$(1))
$(call Image/Build/Profile/V22RW-2X2,$(1))
$(call Image/Build/Profile/VOCORE,$(1))
$(call Image/Build/Profile/W150M,$(1))
$(call Image/Build/Profile/W306R_V20,$(1))
$(call Image/Build/Profile/W502U,$(1))
$(call Image/Build/Profile/WCR150GN,$(1))
$(call Image/Build/Profile/WHRG300N,$(1))
$(call Image/Build/Profile/WIZARD8800,$(1))
$(call Image/Build/Profile/WIZFI630A,$(1))
$(call Image/Build/Profile/WL-330N,$(1))
$(call Image/Build/Profile/WL-330N3G,$(1))
$(call Image/Build/Profile/WL-341V3,$(1))
$(call Image/Build/Profile/WL-351,$(1))
$(call Image/Build/Profile/WNCE2001,$(1))
$(call Image/Build/Profile/WR512-3GN,$(1))
$(call Image/Build/Profile/WR6202,$(1))
$(call Image/Build/Profile/WT1520,$(1))
$(call Image/Build/Profile/X5,$(1))
$(call Image/Build/Profile/X8,$(1))
$(call Image/Build/Profile/XDXRN502J,$(1))
$(call Image/Build/Profile/MZK-DP150N,$(1))
endef
endif
#
# RT3662/RT3883 Profiles
#
# $(1) = squashfs/initramfs
# $(2) = lowercase board name
# $(3) = dts file
# $(4) = kernel size
# $(5) = rootfs size
# $(6) = signature
# $(7) = model
# $(8) = flash address
# $(9) = start address
define BuildFirmware/EdimaxCombined/squashfs
$(call PatchKernelLzmaDtb,$(2),$(3))
$(call MkImage,lzma,$(KDIR)/vmlinux-$(2).bin.lzma,$(KDIR)/vmlinux-$(2).bin.uImage)
if [ `stat -c%s "$(KDIR)/vmlinux-$(2).bin.uImage"` -gt `expr $(4) - 20` ]; then \
echo "Warning: $(KDIR)/vmlinux-$(2).bin.uImage is too big" >&2; \
exit 1; \
else if [ `stat -c%s "$(KDIR)/root.$(1)"` -gt $(5) ]; then \
echo "Warning: $(KDIR)/root.$(1) is too big" >&2; \
exit 1; \
else \
( dd if=$(KDIR)/vmlinux-$(2).bin.uImage bs=`expr $(4) - 20` conv=sync ; dd if=$(KDIR)/root.$(1) ) > $(KDIR)/vmlinux-$(2).bin.uImage.combined ; \
fi ; fi
mkedimaximg -i "$(KDIR)/vmlinux-$(2).bin.uImage.combined" \
-o $(call imgname,$(1),$(2)).bin \
-s $(6) -m $(7) -f $(8) -S $(9)
endef
Image/Build/Profile/CYSWR1100=$(call BuildFirmware/Seama/$(1),$(1),cy-swr1100,CY-SWR1100,wrgnd10_samsung_ss815,$(ralink_default_fw_size_8M))
Image/Build/Profile/DIR645=$(call BuildFirmware/Seama/$(1),$(1),dir-645,DIR-645,wrgn39_dlob.hans_dir645,$(ralink_default_fw_size_8M))
hpm_mtd_size=16449536
Image/Build/Profile/HPM=$(call BuildFirmware/CustomFlash/$(1),$(1),hpm,HPM,$(hpm_mtd_size))
define BuildFirmware/RTN56U/squashfs
$(call BuildFirmware/Default8M/$(1),$(1),rt-n56u,RT-N56U)
-mkrtn56uimg -s $(call sysupname,$(1),rt-n56u)
-cp $(call sysupname,$(1),rt-n56u) $(call imgname,$(1),rt-n56u)-factory.bin
-mkrtn56uimg -f $(call imgname,$(1),rt-n56u)-factory.bin
endef
Image/Build/Profile/RTN56U=$(call BuildFirmware/RTN56U/$(1),$(1),rt-n56u,RT-N56U)
Image/Build/Profile/TEW691GR=$(call BuildFirmware/UMedia/$(1),$(1),tew-691gr,TEW-691GR,0x026910)
Image/Build/Profile/TEW692GR=$(call BuildFirmware/UMedia/$(1),$(1),tew-692gr,TEW-692GR,0x026920)
kernel_size_BR6475ND:=2097152
rootfs_size_BR6475ND:=5832704
Image/Build/Profile/BR6475ND=$(call BuildFirmware/EdimaxCombined/$(1),$(1),br-6475nd,BR-6475ND,$(kernel_size_BR6475ND),$(rootfs_size_BR6475ND),CSYS,RN54,0x70000,0x01100000)
ifeq ($(SUBTARGET),rt3883)
define Image/Build/Profile/Default
$(call Image/Build/Profile/CYSWR1100,$(1))
$(call Image/Build/Profile/DIR645,$(1))
$(call Image/Build/Profile/HPM,$(1))
$(call Image/Build/Profile/RTN56U,$(1))
$(call Image/Build/Profile/BR6475ND,$(1))
$(call Image/Build/Profile/TEW691GR,$(1))
$(call Image/Build/Profile/TEW692GR,$(1))
endef
endif
#
# MT7620A Profiles
#
Image/Build/Profile/E1700=$(call BuildFirmware/UMedia/$(1),$(1),e1700,E1700,0x013326)
Image/Build/Profile/MT7620a=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a,MT7620a)
Image/Build/Profile/MT7620a_MT7610e=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7610e,MT7620a_MT7610e)
Image/Build/Profile/MT7620a_MT7530=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7530,MT7620a_MT7530)
Image/Build/Profile/MT7620a_V22SG=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_v22sg,MT7620a_V22SG)
br100_mtd_size=8126464
Image/Build/Profile/AI-BR100=$(call BuildFirmware/CustomFlash/$(1),$(1),ai-br100,AI-BR100,$(br100_mtd_size),Ai-BR)
Image/Build/Profile/RP-N53=$(call BuildFirmware/Default8M/$(1),$(1),rp-n53,RP-N53)
whr_300hp2_mtd_size=7012352
Image/Build/Profile/WHR300HP2=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-300hp2,WHR-300HP2,$(whr_300hp2_mtd_size))
Image/Build/Profile/WHR600D=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-600d,WHR-600D,$(whr_300hp2_mtd_size))
whr_1166d_mtd_size=15400960
Image/Build/Profile/WHR1166D=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-1166d,WHR-1166D,$(whr_1166d_mtd_size))
dlink810l_mtd_size=6881280
Image/Build/Profile/CF-WR800N=$(call BuildFirmware/Default8M/$(1),$(1),cf-wr800n,CF-WR800N)
Image/Build/Profile/DIR-810L=$(call BuildFirmware/CustomFlash/$(1),$(1),dir-810l,DIR-810L,$(dlink810l_mtd_size))
na930_mtd_size=20971520
Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
Image/Build/Profile/DB-WRT01=$(call BuildFirmware/Default8M/$(1),$(1),db-wrt01,DB-WRT01)
Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
Image/Build/Profile/HC5661=$(call BuildFirmware/Default16M/$(1),$(1),hc5661,HC5661)
Image/Build/Profile/HC5761=$(call BuildFirmware/Default16M/$(1),$(1),hc5761,HC5761)
Image/Build/Profile/HC5861=$(call BuildFirmware/Default16M/$(1),$(1),hc5861,HC5861)
Image/Build/Profile/OY-0001=$(call BuildFirmware/Default16M/$(1),$(1),oy-0001,OY-0001)
Image/Build/Profile/Y1=$(call BuildFirmware/Default16M/$(1),$(1),y1,Y1)
Image/Build/Profile/Y1S=$(call BuildFirmware/Default16M/$(1),$(1),y1s,Y1S)
Image/Build/Profile/MLW221=$(call BuildFirmware/Default16M/$(1),$(1),mlw221,MLW221)
Image/Build/Profile/MLWG2=$(call BuildFirmware/Default16M/$(1),$(1),mlwg2,MLWG2)
Image/Build/Profile/WMR-300=$(call BuildFirmware/Default8M/$(1),$(1),wmr-300,WMR-300)
Image/Build/Profile/RT-N14U=$(call BuildFirmware/Default8M/$(1),$(1),rt-n14u,RT-N14U)
Image/Build/Profile/WRTNODE=$(call BuildFirmware/Default16M/$(1),$(1),wrtnode,WRTNODE)
Image/Build/Profile/WT3020=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
Image/Build/Profile/MIWIFI-MINI=$(call BuildFirmware/Default16M/$(1),$(1),miwifi-mini,MIWIFI-MINI)
Image/Build/Profile/ZTE-Q7=$(call BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
Image/Build/Profile/YOUKU-YK1=$(call BuildFirmware/Default16M/$(1),$(1),youku-yk1,YOUKU-YK1)
Image/Build/Profile/ZBT-WA05=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
Image/Build/Profile/ZBT-WR8305RT=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wr8305rt,ZBT-WR8305RT)
Image/Build/Profile/ArcherC20i=$(call BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
microwrt_mtd_size=16515072
Image/Build/Profile/MicroWRT=$(call BuildFirmware/CustomFlash/$(1),$(1),microwrt,MicroWRT,$(microwrt_mtd_size))
Image/Build/Profile/TINY-AC=$(call BuildFirmware/Default8M/$(1),$(1),tiny-ac,TINY-AC)
ifeq ($(SUBTARGET),mt7620)
define Image/Build/Profile/Default
$(call Image/Build/Profile/E1700,$(1))
$(call Image/Build/Profile/MT7620a,$(1))
$(call Image/Build/Profile/MT7620a_MT7610e,$(1))
$(call Image/Build/Profile/MT7620a_MT7530,$(1))
$(call Image/Build/Profile/MT7620a_V22SG,$(1))
$(call Image/Build/Profile/AI-BR100,$(1))
$(call Image/Build/Profile/CF-WR800N,$(1))
$(call Image/Build/Profile/RP-N53,$(1))
$(call Image/Build/Profile/DIR-810L,$(1))
$(call Image/Build/Profile/WHR300HP2,$(1))
$(call Image/Build/Profile/WHR600D,$(1))
$(call Image/Build/Profile/WHR1166D,$(1))
$(call Image/Build/Profile/DB-WRT01,$(1))
$(call Image/Build/Profile/MZK-750DHP,$(1))
$(call Image/Build/Profile/NA930,$(1))
$(call Image/Build/Profile/HC5661,$(1))
$(call Image/Build/Profile/HC5761,$(1))
$(call Image/Build/Profile/HC5861,$(1))
$(call Image/Build/Profile/OY-0001,$(1))
$(call Image/Build/Profile/Y1,$(1))
$(call Image/Build/Profile/Y1S,$(1))
$(call Image/Build/Profile/MLW221,$(1))
$(call Image/Build/Profile/MLWG2,$(1))
$(call Image/Build/Profile/WMR-300,$(1))
$(call Image/Build/Profile/RT-N14U,$(1))
$(call Image/Build/Profile/WRTNODE,$(1))
$(call Image/Build/Profile/WT3020,$(1))
$(call Image/Build/Profile/MIWIFI-MINI,$(1))
$(call Image/Build/Profile/ZTE-Q7,$(1))
$(call Image/Build/Profile/YOUKU-YK1,$(1))
$(call Image/Build/Profile/ZBT-WA05,$(1))
$(call Image/Build/Profile/ZBT-WR8305RT,$(1))
$(call Image/Build/Profile/ArcherC20i,$(1))
$(call Image/Build/Profile/MicroWRT,$(1))
$(call Image/Build/Profile/TINY-AC,$(1))
endef
endif
#
# MT7621 Profiles
#
ifeq ($(SUBTARGET),mt7621)
ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX) This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 ubnt-erx witi wf-2881 zbt-wg2626
endif
define Device/mt7621
DTS := MT7621
IMAGE_SIZE := $(ralink_default_fw_size_4M)
endef
define Device/wsr-600
DTS := WSR-600
endef
define Device/re6500
DTS := RE6500
endef
define Device/wsr-1166
DTS := WSR-1166
IMAGE/sysupgrade.bin := trx | pad-rootfs
endef
define Device/dir-860l-b1
DTS := DIR-860L-B1
IMAGES += factory.bin
KERNEL := kernel-bin | patch-dtb | relocate-kernel | lzma | uImage lzma
IMAGE/sysupgrade.bin := \
append-kernel | pad-offset 65536 64 | append-rootfs | \
seama -m "dev=/dev/mtdblock/2" -m "type=firmware" | \
pad-rootfs | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin := \
append-kernel | pad-offset 65536 64 | append-rootfs | pad-rootfs -x 64 | \
seama -m "dev=/dev/mtdblock/2" -m "type=firmware" | \
check-size $$$$(IMAGE_SIZE) | \
seama-seal -m "signature=wrgac13_dlink.2013gui_dir860lb"
endef
define Device/firewrt
DTS := FIREWRT
IMAGE_SIZE := $(ralink_default_fw_size_16M)
endef
define Device/pbr-m1
DTS := PBR-M1
IMAGE_SIZE := $(ralink_default_fw_size_16M)
endef
define Device/sap-g3200u3
DTS := SAP-G3200U3
endef
define Device/witi
DTS := WITI
IMAGE_SIZE := $(ralink_default_fw_size_16M)
endef
define Device/zbt-wg2626
DTS := ZBT-WG2626
IMAGE_SIZE := $(ralink_default_fw_size_16M)
endef
define Device/wf-2881
DTS := WF-2881
BLOCKSIZE := 128KiB
PAGESIZE := 2048
KERNEL_SIZE := 2097152
FILESYSTEMS := squashfs
IMAGE/sysupgrade.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE)
endef
ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX) This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
define Device/ubnt-erx
DTS := UBNT-ERX
FILESYSTEMS := squashfs
KERNEL_SIZE := 3145728
KERNEL := $(KERNEL_DTB) | uImage lzma
IMAGES := sysupgrade.tar factory-initramfs.tar
IMAGE/factory-initramfs.tar := ubnt-erx-factory-compat | \
ubnt-erx-factory-kernel | \
ubnt-erx-factory-rootfs | \
ubnt-erx-factory-version | \
ubnt-erx-factory-check-size $$(KERNEL_SIZE)
ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX) This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
IMAGE/sysupgrade.tar := sysupgrade-nand
endef
#
# MT7628 Profiles
#
Image/Build/Profile/MT7628=$(call BuildFirmware/Default4M/$(1),$(1),mt7628,MT7628)
ifeq ($(SUBTARGET),mt7628)
define Image/Build/Profile/Default
$(call Image/Build/Profile/MT7628,$(1))
endef
endif
#
# MT7688 Profiles
#
Image/Build/Profile/LinkIt7688=$(call BuildFirmware/Default32M/$(1),$(1),LinkIt7688,LINKIT7688)
ifeq ($(SUBTARGET),mt7688)
define Image/Build/Profile/Default
$(call Image/Build/Profile/LinkIt7688,$(1))
endef
endif
ifndef TARGET_DEVICES
#
# Generic Targets - only needed for legacy image building code
#
define Image/BuildKernel
cp $(KDIR)/vmlinux.elf $(BIN_DIR)/$(VMLINUX).elf
cp $(KDIR)/vmlinux $(BIN_DIR)/$(VMLINUX).bin
$(call CompressLzma,$(KDIR)/vmlinux,$(KDIR)/vmlinux.bin.lzma)
$(call MkImage,lzma,$(KDIR)/vmlinux.bin.lzma,$(KDIR)/uImage.lzma)
cp $(KDIR)/uImage.lzma $(BIN_DIR)/$(UIMAGE).bin
endef
define Image/BuildKernel/Initramfs
cp $(KDIR)/vmlinux-initramfs.elf $(BIN_DIR)/$(VMLINUX)-initramfs.elf
cp $(KDIR)/vmlinux-initramfs $(BIN_DIR)/$(VMLINUX)-initramfs.bin
$(call CompressLzma,$(KDIR)/vmlinux-initramfs,$(KDIR)/vmlinux-initramfs.bin.lzma)
$(call MkImage,lzma,$(KDIR)/vmlinux-initramfs.bin.lzma,$(KDIR)/uImage-initramfs.lzma)
cp $(KDIR)/uImage-initramfs.lzma $(BIN_DIR)/$(UIMAGE)-initramfs.bin
$(call Image/Build/Initramfs)
endef
define Image/Build
$(call Image/Build/$(1))
dd if=$(KDIR)/root.$(1) of=$(BIN_DIR)/$(IMG_PREFIX)-root.$(1) bs=128k conv=sync
$(call Image/Build/Profile/$(PROFILE),$(1))
endef
endif
ifeq ($(SUBTARGET),mt7621)
define Image/Prepare
#define Build/Compile
rm -rf $(KDIR)/relocate
$(CP) ../../generic/image/relocate $(KDIR)
$(MAKE) -C $(KDIR)/relocate KERNEL_ADDR=$(KERNEL_LOADADDR) CROSS_COMPILE=$(TARGET_CROSS)
$(CP) $(KDIR)/relocate/loader.bin $(KDIR)/loader.bin
endef
endif
$(eval $(call BuildImage))