Commit graph

3349 commits

Author SHA1 Message Date
Piotr Dymacz
597c9f0be5 ar71xx: image: fix indentation
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 22:02:47 +01:00
Piotr Dymacz
4436979c83 ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.

CPE505 is an outdoor CPE with PoE support and detachable antennas.

Both devices are based on Qualcomm/Atheros QCA9531 v2.

Common specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB

R602N specification:

- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button

CPE505N specification:

- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button

Flash instructions:

It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").

Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:

fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"

Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.

If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:

1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset

These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".

Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 17:59:47 +01:00
Vaclav Svoboda
0d9adb4832 ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.

- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
   (v2: Macronix MX 25L323F)
   (v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-23 09:41:15 +01:00
Ryan Mounce
978998628f ar71xx: add support for MikroTik hAP ac
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).

All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Ryan Mounce
540edf7045 ar71xx: add support for MikroTik hAP ac lite
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).

The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Thibaut VARENE
e1f3cf7ede ar71xx: mikrotik: prepend "RouterBOARD" to machine name for NOR devices
When the device name doesn't already contain "RouterBOARD", this patch adds
this string to the machine name.

Most NOR devices already have "RouterBOARD" in their hardware-stored device name,
but not all of them.

This patch also makes the code more robust against buffer overflows.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Thibaut VARENE
e3dc036cbf ar71xx: add support for RB LHG 5nD
This patch adds support for the MikroTik RouterBOARD LHG 5
https://routerboard.com/RBLHG-5nD

Specifications:
- SoC: Atheros AR9344 (600MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin AR9344 5GHz, 2x2:2
- Ethernet: 1x100M

Initial flash via initramfs, like all other RB devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Daniel Gonzalez Cabanelas
080c6fa476 ar71xx: WNDR4300: Fix network vlan IDs
The Netgear WNDR4300 has the VLAN IDs flipped in LuCi, fix it.

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2017-03-13 00:13:18 +01:00
Daniel Gonzalez Cabanelas
ad9ad376bb ar71xx: WNDR4300: Fix switch HW controlled LEDs
The Netgear WNDR4300, equipped with an Atheros AR8327 Gigabit Switch,
has two LEDs on each port for monitoring LAN activity, but it currently
only uses one. Fix the configuration to use both.

The patch provides this new configuration:
- green LED: 1 Gbps link, 4Hz blink frequency
- amber LED: 10/100 Mbps link. 4Hz for 100Mbps, 2Hz for 10Mbps

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2017-03-13 00:12:07 +01:00
Piotr Dymacz
09862bb006 ar71xx: fix Wallys DR344 ethernet MAC addresses offsets
Without this fix, ethernet interfaces on Wallys DR344 use random MAC
addresses.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:52:19 +01:00
Piotr Dymacz
7e38ce2e7d ar71xx: base-files: few minor cleanups in lib/ar71xx.sh
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:47:59 +01:00
Piotr Dymacz
c2b5206c80 ar71xx: base-files: fix boards order in lib/ar71xx.sh
Keep everything within case statements in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:47:59 +01:00
Piotr Dymacz
d9bc3e6882 ar71xx: base-files: shorten case statement patterns in lib/ar71xx.sh
At now there is no general rule about what part of (or whole) machine
name string should be used for board name assignment/detection and every
target handles this in a different way.

For most of the boards in ar71xx we already use only part of the string,
generally without the vendor name.

This shortens wildcards patterns in case statement for board name
assignment, wherever possible (e.g. where it won't be misleading).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:47:59 +01:00
Piotr Dymacz
4f09837cdf ar71xx: base-files: always use double quotes in lib/ar71xx.sh
Be consistent and always use double quotes for case statement patterns,
as in other targets. With this approach it should be less confusing for
users adding support for new devices.

Also, be consistent with MikroTik boards wildcard pattern.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:43:17 +01:00
Piotr Dymacz
589b37e8b5 ar71xx: base-files: fix indentation in lib/ar71xx.sh
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 17:39:12 +01:00
Piotr Dymacz
e213647399 ar71xx: fix machine name for several devices
Be consistent with form and format of the vendor name.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 17:39:12 +01:00
Shuanglin Liu
53ef20f65a ar71xx: add support for Rockeetech AP531B0
Specification:
- SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB))
- RAM: 64 MiB DDR2
- Storage: 16 MiB of flash (optional 16 MiB second flash)
- Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0) 1x100M (port 4)
- PCI-E: x1
- SIMcard slot: x1
- USB 2.0 port: x1 (optional)
- Ext GPIO pin: x8
- UART for serial console: x1
- External watchdog: x1 (optional)
- Power supply: 9-48V (DC jack/passive PoE)

Installation through tftp:
- Copy <Firmware Image Name> into tftp directory
- Connect board via ttl port and Ethernet port
- Boot the AP531B0
- When "Autobooting in 1 seconds" appears press Enter
- Set serverip and ipaddr appropriate
  (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1)
- Enter "tftp 0x8050000 <Firmware Image Name>"
- Enter "erase 0x9f050000 +$filesize"
- Enter "cp.b 0x80500000 0x9f050000 $filesize"
- Enter "reset"

Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
2017-03-12 17:38:31 +01:00
Hauke Mehrtens
31c6452107 kernel: update kernel 4.4 to 4.4.53
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-12 15:46:02 +01:00
Stijn Segers
0ad82375cd ar71xx: add ath10k driver and firmware for Netgear R6100 to firmware image
A Netgear R6100 owner reported the LEDE images lack the ath10k driver and firmware [1]. This patch adds both to the R6100 image.

[1] https://forum.lede-project.org/t/netgear-r6100-5ghz-wifi-not-working-after-initial-install/2222

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2017-03-11 08:30:56 +01:00
Felix Fietkau
0504cd22aa ar71xx: fix build without CONFIG_NOP_USB_XCEIV (FS#593)
Open-code usb_phy_generic_register instead of calling it, since it is
really trivial. Avoid pulling CONFIG_NOP_USB_XCEIV into the kernel
config and add a proper dependency instead

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-07 11:37:50 +01:00
Wojciech Jowsa
f223c4a923 ar71xx: set status led for the gl-* boards
Signed-off-by: Wojciech Jowsa <w.jowsa@radytek.com>
2017-03-06 07:50:11 +01:00
Thibaut VARENE
ed49d08762 ar71xx: mikrotik: erase firmware partition on SPI NOR devices in pre_upgrade()
On Mikrotik SPI NOR devices, the firmware partition must be erased when flashing
from stock firmware, otherwise leftover bits (in particular a kernel signature)
can trigger a boot loop.

When booted from initramfs (the only way to flash LEDE on these devices),
this patch unconditionally erases the firmware partition in the pre_upgrade()
stage for all supported SPI NOR devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-26 13:30:39 +01:00
Arvid E. Picciani
0d09c7281f ar71xx: Enable RB2011 TTY
Enables TTY on the Mikrotik RouterBoard RB2011*R*

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2017-02-26 08:46:09 +01:00
Felix Fietkau
eb4f70a3cd ar71xx: use common firmware partition for WNDAP360
Patch from https://github.com/openwrt/openwrt/pull/398

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-23 16:27:47 +01:00
Kevin Darbyshire-Bryant
91a65f6c88 kernel: update kernel 4.4 to 4.4.50
Bump kernel from 4.4.49 to 4.4.50

Compile tested: All targets

Run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2017-02-23 10:40:21 +01:00
Thibaut VARENE
f6a52bf337 ar71xx: Enable mtdsplit support for RB SPI NOR devices
This patch enables mtdsplit for the MikroTik subtarget.
It converts mach-rbspi.c to use a single "firmware" partition.
Finally, it converts the SPI NOR profile to metadata images:
the original combined-image format is gone, the images are now
"standard" sysupgrade images with metadata appended.

Note: kernel2minor apparently pads the kernel container to erase-block
boundary, but this is undocumented behaviour, so we do not rely on it
and call pad-to anyway.

Note: in platform.sh, the boards are tested last in platform_check_image()
as this should eventually become the "*)" default case when more devices
switch to metadata images.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-22 22:52:20 +01:00
Thibaut VARENE
53c862705d ar71xx: remove bogus "rb*)" catch-all from platform.sh
This patch replaces a dangerous catch-all with the exhaustive list of devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-22 22:52:19 +01:00
Weijie Gao
3ee793f601 ar71xx: fix vlan settings for some boards
For AR71XX devices, GMAC1 always connects port 0 of the built-in switch,
as the CPU port.

This patch sets correct vlan for some devices with wrong settings:
a) mark port 0 as CPU port, tagged
b) reverse port order, marking these ports untagged

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2017-02-20 09:27:43 +01:00
Thibaut VARENE
6e4549138d ar71xx: Add more boards to the routerboard serial detection patch
This patch enables serial console on the 435 series and the 953gs.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-20 09:20:48 +01:00
Thomas Roberts
f9278337cf ar71xx: add support for TL-WR802N Version 2
This patch adds support for the TP-Link TL-WR802N Version 2.

Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
2017-02-20 09:10:17 +01:00
Felix Fietkau
72327d1757 ar71xx: fix ethernet PLL configuration for QCA956x
QCA956x is configured like AR934x, not like the older chips.
Should fix ethernet hangs when using the WAN port without SGMII

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-17 12:16:13 +01:00
Henryk Heisig
d6baeb5c48 ar71xx: fix lan ports on archer C59 and C60
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-02-17 10:30:48 +01:00
Karol Dudek
58fc50f1b0 ar71xx: add support for 8devices Lima board
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.

Specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO

Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery

Tested on:

- Lima development kit

Signed-off-by: Karol Dudek <karoiz@sli.pl>
2017-02-17 10:19:09 +01:00
Thibaut VARENE
748e701b74 ar71xx: add preliminary kernel support for several RB SPI NOR devices
The cAP 2nD, mAP 2nD and wAP 2nD apparently all share the same QCA953x/SPI-NOR
platform.

This patch adds preliminary kernel support based on init data used in
Mikrotik's linux-3.3.5 kernel patch. Since this is totally experimental and
untested, the necessary glue in base-files has not been added, the code is
provided as a starting point in case somebody with that hardware wants to help
getting it supported.

The cAP lite (cAPL 2nD) should also be supported once it is determined whether
or not it uses the same board identifier as the mAP lite.

Code has been successfully built and has no side effect (no impact on already
supported devices).

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:59 +01:00
Thibaut VARENE
b800453282 ar71xx: add new SPI NOR RB devices to the list of serial-enable patch
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:59 +01:00
Thibaut VARENE
b2044a7f60 ar71xx: add support for RB750r2
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2

Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)

This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
19f42663d2 ar71xx: add support for RB750UPr2
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

This ethernet router is based on the same platform as the wireless router hAP.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
8cbb2ac633 ar71xx: add support for RB951Ui-2nD
This patch adds support for the MikroTik RouterBOARD hAP
https://routerboard.com/RB951Ui-2nD

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
b18bae37a4 ar71xx: provide support for RB-941-2nD via mach-rbspi.c
This patch implements support for the hAP lite in mach-rbspi.c

hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Thibaut VARENE
c59fa94eee ar71xx: add support for RB mAP L-2nD
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD

Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M

This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Felix Fietkau
f533b94436 ar71xx: fix DEFAULT_PACKAGES for mikrotik devices
Include packages from the default profile for NAND devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-14 13:15:44 +01:00
Alexandru Gagniuc
6cce9557a0 ar71xx: Add support for D-Link EBR-2310 Rev. C
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2017-02-14 12:27:14 +01:00
Piotr Dymacz
56561b9f51 ar71xx: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-14 12:25:33 +01:00
Sven Eckelmann
3d16c16eb6 ar71xx: Add missing device package om-watchdog for MR1750
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
391d498fe5 ar71xx: add OpenMesh A40 to OpenMesh A60 profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
d0061798a6 ar71xx: extract ath10k wifi board.bin for the OpenMesh A40 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
c6e1bb2ace ar71xx: enable sysupgrade for the OpenMesh A40
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
640f9158e2 ar71xx: add user-space support for the OpenMesh A40
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
5e61a8331d ar71xx: add kernel support for the OpenMesh A40 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
5e50adeed3 ar71xx: create profile and build image for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
1330ff189b ar71xx: extract ath10k wifi board.bin for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
fce57c4082 ar71xx: enable sysupgrade for the OpenMesh A60
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
174605c467 ar71xx: add user-space support for the OpenMesh A60
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
417f9e7e82 ar71xx: add kernel support for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
baaf0acded ar71xx: enable sysupgrade for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Sven Eckelmann
bdfe4c1218 ar71xx: add user-space support for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Sven Eckelmann
e1b50457b0 ar71xx: add kernel support for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Sven Eckelmann
019276a9c6 ar71xx: Remove the v2/v3 from the OpenMesh profile names
The list of v2/v3 devices is getting longer and makes reading the names of
the profiles unnecessary hard.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Thibaut VARENE
33154eaf41 ar71xx: fix platform_find_rootfspart()
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-12 15:57:37 +01:00
Piotr Dymacz
f5416b0622 ar71xx: image: drop redundant CONSOLE assignment
Default CONSOLE value for ar71xx target is "ttyS0,115200", so there
is no need to specify the same value in device profiles.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-09 09:45:27 +01:00
Jo-Philipp Wich
ea269c37b8 ar71xx/ipq806x/mediatek/mvebu: fix network defaults
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.

Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-07 09:32:28 +01:00
Piotr Dymacz
a4d12aed30 ar71xx: image: fix DEVICE_TITLE for several devices
Be consistent with form and format of the vendor names.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Piotr Dymacz
c3ef8daff4 ar71xx: fix indentation in Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Piotr Dymacz
cc1fb9662c ar71xx: drop help sections from Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Piotr Dymacz
bed9729587 ar71xx: fix up mikrotik subtarget kernel config
Disable all devices which do not belong to the mikrotik subtarget.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Piotr Dymacz
670e14ed70 ar71xx: fix up nand subtarget kernel config
Disable all devices which do not belong to the nand subtarget.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Piotr Dymacz
4fe92554ac ar71xx: select ATH79_NVRAM only by boards actually use it
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Felix Fietkau
1533f1db92 ar71xx: add missing DEVICE_TITLE for mikrotik devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-29 17:32:48 +01:00
FUKAUMI Naoki
e5a0eb2af5 ar71xx: prepare jffs2 partition properly in factory.bin for BHR-4GRV2
"pad-rootfs" is required just after "append-rootfs".

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-28 20:29:00 +01:00
Koen Vandeputte
4d1515070b kernel: bump to 4.4.45
Refreshed patches for all supported targets.

Compiled & tested on cns3xxx & imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-01-27 23:17:49 +01:00
Mathias Kresin
893962bcf8 Revert "ar71xx: fix Archer C7 LED colour names"
This reverts commit e79ecb4c26.

The commit was incomplete and the issue that should be fixed isn't
that easy fixable. The Archer C7 mach file is used for the Archer C5,
WDR4900 and WDR7500 as well. Where the WDRs in compare to the Archer
do have blue LEDs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-27 22:16:24 +01:00
Stijn Segers
20996edd68 Kernel: bump to 4.4.44
Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64.

.44 has been run-tested on the 17.01 branch here on ar71xx and mt7621.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2017-01-27 11:18:27 +01:00
Mathias Kresin
e79ecb4c26 ar71xx: fix Archer C7 LED colour names
All LEDs on this board are green.

Fixes: FS#409

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-27 11:10:10 +01:00
Henryk Heisig
e39dc8d823 ar71xx: add support to TP-Link Archer C59v1 and C60v1
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB

TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")

Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:21 +01:00
Henryk Heisig
eec0c41375 ar71xx: QCA956X: add missing register
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-01-26 11:38:20 +01:00
Qian Zheng
b822f29f25 ar71xx: fix netgear wndr3700 v1/v2, wndr3800/wndr3800ch switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
2017-01-26 11:38:20 +01:00
Qian Zheng
3d4069fb8e ar71xx: fix netgear wnr2000 v3 switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
[Jo-Philipp Wich: fix alphabetical order after merging with gl-ar300 case]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:20 +01:00
Qian Zheng
810eb8d0ea ar71xx: fix tl-wr841n-v7 switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
[Jo-Philipp Wich: fix alphabetical order]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:20 +01:00
Alex Samorukov
d872b732e7 ar71xx: Fix mikrotik subtarget default profile for device profile selection
Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
2017-01-25 08:01:25 +01:00
Alex Samorukov
17401b3d5c ar71xx: improve Mikrotik hAP Lite device support
- remove CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
- enable jffs2 support
- fix sysupgrade

Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
2017-01-25 08:00:11 +01:00
Felix Fietkau
83783f296a uboot-ar71xx: switch to using u-boot.mk
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 16:21:24 +01:00
Felix Fietkau
bfdc56d3a2 build: remove mips16 feature flag from target makefiles
It can be implicitly derived from the MIPS32 revision support in the
kernel configuration

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:15:01 +01:00
John Crispin
236fcedc51 Revert "ar71xx: wrt400n: lift size limit on kernel and rootfs part"
This reverts commit 78c2ec0f47.

The builders were failing with a segfault when generating the image

Signed-off-by: John Crispin <john@phrozen.org>
2017-01-20 06:43:13 +01:00
YuheiOKAWA
261415a660 ar71xx: add support for PQI Air Pen
SoC: AR9331
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

Changes in v2:
alphabetical ordering, tabs fron spaces.
2017-01-20 00:52:48 +01:00
Yousong Zhou
78c2ec0f47 ar71xx: wrt400n: lift size limit on kernel and rootfs part
While at it, convert to new build method

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-20 00:44:46 +01:00
Conor O'Gorman
274546046d ar71xx: add Abicom SC1750 support
Support Abicom International Scorpion SC1750 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB Nor Flash
1x SFP, 1x PCIe
2x 10/100/1000 Ethernet
135x100 mm
802.11ng/g/b
802.11ac/an/a

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:40 +01:00
Conor O'Gorman
d38ffd8cd9 ar71xx: add Abicom SC450 support
Support Abicom International Scorpion SC450 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:33 +01:00
Conor O'Gorman
eb97f41fc2 ar71xx: add Abicom SC300M support
Support Abicom International Scorpion SC300M Module

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:27 +01:00
Svetoslav Neykov
97b52593bc ar71xx: Chipidea USB device support
Changes the platform to use the Chipidea driver instead of the
generic USB host driver which has support for both host and
device modes (selected on boot).

The changes in 930-chipidea-pullup.patch are already in mainline.
I'll upstream 920-usb-chipidea-AR933x-platform-support.patch once I
can test the changes with a newer kernel.

Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
2017-01-20 00:37:01 +01:00
Thibaut VARENE
29d0ac35bd ar71xx: mark soft_config mtd part as writeable for RB-941-2nD
The soft_config partition must be writeable for rbcfg to be able to
enact changes to the routerboot configuration.
The read-only flag was a mistake in the initial patch. Removing it
brings mach-rb941.c in line with all other RB platforms.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-01-18 12:05:43 +01:00
Felix Fietkau
00144d2730 ar71xx: fix up the kernel config for the mikrotik subtarget
Limit enabled devices to routerboards, disable all other devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:13 +01:00
Cezary Jackiewicz
05115e9656 ar71xx: fix network config for Mikrotik RB411U
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2017-01-16 20:40:12 +01:00
Thibaut VARENE
3f7841a70a ar71xx: add support for RB-941-2nD
Add full support for Mikrotik RB-941-2nD (hAP lite)

Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
Felix Fietkau
9db9072d67 ar71xx: convert mikrotik routerboard support to UBI
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.

There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
Felix Fietkau
0e547400fb ar71xx: create a proper default profile for the mikrotik subtarget, drop other profiles
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
João Chaínho
ace9d1fb6f ar71xx: Detect USB port on Mikrotik RB750UP
The USB port on Mikrotik RB750UP isn’t detected. This patch provides a fix. Tested and working.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2017-01-15 17:43:14 +01:00
Felix Fietkau
1708644f19 kernel: backport MIPS changes introducing a separate IRQ stack
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-15 18:25:54 +01:00
Felix Fietkau
d6c77b9d99 ar71xx: default to external USB power on RB-912UAG
There's a GPIO that can switch between power to USB pins for the
internal MiniPCIe slot or the external USB port.
People are more likely to use the external one so enable it by default.
Existing configurations should be unaffected

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 10:53:05 +01:00
David Varga
d7fd1a0f8d ar71xx: enable serial console on Mikrotik RB411/RB433
This patch adds support for serial console on Mikrotik RB411 and RB433
series devices.

Signed-off-by: David Varga <duvi@duvinet.hu>
[picked from FS#377]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-13 08:32:20 +01:00
Felix Fietkau
e21cb649a2 ar71xx: disable sub-page writes on routerboard nand drivers
They seem to fail in tests using UBI, and are not used by yaffs2

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:10:19 +01:00
Felix Fietkau
b1dbe6028e ar71xx: fix legacy image build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:09:21 +01:00
Felix Fietkau
889272d92d ar71xx: fix RB4xx CPLD SPI device mode setup
Commit af79fdbe4a changed the code to use tx_nbits for dual SPI tx
transfers, however the SPI stack only allows this when the device mode
includes the relevant bit as well

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:02:11 +01:00
Felix Fietkau
c3a8b87773 ar71xx: fix RB4xx SPI driver mode bits
Accept SPI_TX_DUAL in device mode to fix the CPLD driver

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:02:11 +01:00
Stijn Tintel
0d3dc16931 ar71xx: drop references to madwifi
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:02:00 +01:00
Matthias Schiffer
1fef80f29c
ar71xx: add support for TP-Link WBS210/510
The devices are mostly identical to the CPE210/510, but use external
antennas.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-01-05 16:01:17 +01:00
Felix Fietkau
af79fdbe4a ar71xx: remove a non-upstream spi core patch
- use standard flags instead
- remove dead code from the rb4xx spi drivers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:13 +01:00
Radek Dostál
3561d89ad6 ar71xx: RE450: enable building of TP-Link RE450
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:06 +01:00
Tal Keren
9c475eca3e ar71xx: add support for TP-Link RE450
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.

The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)

The result factory image is flashable from the stock web ui.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-22 14:50:05 +01:00
Radek Dostál
236fc232bb ar71xx: sort items in 11-ath10k-caldata alphabetically
Requested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:05 +01:00
Tal Keren
0d9d980ecd firmware-utils: kernel image generator for TP-Link RE450
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:05 +01:00
Matthias Schiffer
324bdf3ecc
ar71xx: remove redundant -j from TL-WR1043ND v4 kernel build command
mktplinkfw ignores -j in combined mode, the EOF marker is added by
tplink-safeloader.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-21 23:29:00 +01:00
Ludwig Thomeczek
1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
Matthias Schiffer
0495181529
ar71xx: rename mktplinkfw-initramfs to more generic mktplinkfw-combined
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-20 14:38:48 +01:00
Kevin Darbyshire-Bryant
79abb8f140 kernel: bump to 4.4.39
Bump & refresh patches for all 4.4 targets.

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-12-20 09:35:36 +01:00
David Lutz
aada15af93
ar71xx: add support for TP-LINK TL-WR940N v4
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
2016-12-16 11:12:46 +01:00
Jo-Philipp Wich
98b14e0906 ar71xx: fix TL-WR842N v2 switch port order
The TL-WR842N v2 has the following switch port layout with swconfig port 0
being connected to eth1:

            Power  LAN4    LAN3    LAN2    LAN1    WAN     USB
             (*) | [...] | [...] | [...] | [...] | [...] | [.]
    swconfig port:   1       4       3       2      n/a
    netdev:        eth1    eth1    eth1    eth1    eth0

Adjust the board defaults to match this model specific layout.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-14 18:43:48 +01:00
Gad Krumholz
21cb84435a ar71xx: Added missing support for Linksys E2100L
It's based on the WRT160NL according to
https://wiki.openwrt.org/toh/linksys/e2100l

Based on research done here: https://forum.openwrt.org/viewtopic.php?id=24244
and here: https://forum.openwrt.org/viewtopic.php?pid=120791#p120791 this patch
was conceived.

Signed-off-by: Gad Krumholz <gad.krumholz@gmail.com>
[Jo-Philipp Wich: fix ordering, move addpattern change into separate commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-14 18:42:48 +01:00
Huan Truong
fd62fa752b ar71xx: Add support for Netgear WNR2000v1
This patch adds supports for the WNR2000v1 board with 4MB flash, and
produces device-specific factory, rootfs, and sysupgrade files for the
WNR2000v1. This board is errorneously claimed as supported on the OpenWRT
wiki as AP81, but AP81 image would not work because of APT81 image
requiring having 8MB of flash, while WNR2000v1 has only 4MB.

The image requires the u-boot bootloader to be modified to fuhry's
bootloader first.

Short specification:

- CPU: Atheros AR9132
- 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps
- 4 MB of Flash
- 32 MB of RAM
- UART header (J1) on board
- 1x button

Factory/Initial flash instructions:

- Set up a TFTP server on your local machine.
- Download the uImage for ar71xx-generic and the rootfs image for
  ar71xx-generic-wnr2000 and save in the tftp server root.
- Gain serial access to the router via the UART port (telnetenable over
  the network only won't work!).
- Upgrade the u-boot bootloader to fuhry's version by running the
  script: http://fuhry.com/b/wnr2000/install-repart.sh
- When the router restarts, interrupt u-boot and gain access to u-boot command line.
- Repartititon the board and flash initial uImage and rootfs as follow.

Commands to type in u-boot:

	# tells u-boot that we have a tftp server on 192.168.1.10
	setenv serverip 192.168.1.10

	# tells u-boot that the router should take the address 192.168.1.1
	setenv ipaddr 192.168.1.1

	# erase the region from 0x050000-0x3f0000
	erase 0xbf050000 +0x3A0000

	# loads sqfs.bin on TFTP server, and put it to memory address 0x81000000
	tftpboot 0x81000000 sqfs.bin
	# it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ
	# copy bit by bit 0xZZZZZZ bytes from offset 0x050000
	cp.b 0x81000000 0xbf050000 0xZZZZZZ

	# same to the uImage.bin, write it right next to sqfs.bin
	# again, 0xYYYYYY is the length that tftpboot reports
	tftpboot 0x81000000 uImage.bin
	cp.b 0x81000000 0xbf2a0000 0xYYYYYY

	# We need to tell the kernel what board it is booting into, and where to find the partitions
	setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd"

	# Tell u-boot where to find the uImage
	setenv bootcmd "bootm 0xbf2a0000"

	# Tell u-boot to save parameters to the u-boot-env partitions
	saveenv

	# Reset the board
	reset

Tested on:

- WNR2000v1 board.
- Initial flash works.

Known bugs:

- I don't know why factory image doesn't work on initial flash on stock
  firmware in u-boot recovery mode while it should.
- Sysupgrade does not yet work, if you do -f it will mess up your
  installation (requiring a reinstall of sqfs and uImage).

Signed-off-by: Huan Truong <htruong@tnhh.net>
2016-12-14 10:37:01 +01:00
Jing Lin
c9a9f9b8ce ar71xx: Add ath10k-firmware-qca988x for DomyWifi DW33D
The default package selection was missing the correct FW for ath10k to
work.

Signed-off-by: Jing Lin <mumuqz@163.com>
2016-12-14 10:37:01 +01:00
Kevin Darbyshire-Bryant
f5b833b8fe kernel: bump to 4.4.38
Bump & refresh patches for all 4.4 supported targets.

Compile & run tested: ar71xx - Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-12-13 08:28:28 +01:00
Matthias Schiffer
fcf54f79d2
ar71xx: simplify model detection for TP-Link Pharos devices
This also makes the detection more flexible, as it doesn't need to check
for each model explicitly.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-12 13:45:37 +01:00
Felix Fietkau
8f23ec609c ar71xx: remove obsolete flash chip locking code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:19 +01:00
Felix Fietkau
a5923cd549 ar71xx: remove PB92 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
30285facbe ar71xx: remove AP113 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
4c8a9b8e39 ar71xx: remove AP81 reference design board support
This board is very old and unlikely to still be relevant today.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
fd95dec2e3 ar71xx: remove obsolete duplicate driver source file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
441ee62931 ar71xx: remove AP83 reference design board support
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
fa04682f21 ar71xx: clean up spi controller related patches
Remove various hacks for fast read, un-break device tree support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:17 +01:00
Piotr Dymacz
c198ca682c ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00
Matthias Schiffer
9c5af2489a
ar71xx: fix LEDs and sysupgrade support for TL-WA801ND v3
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-06 19:08:35 +01:00
Felix Fietkau
2135e54c00 ar71xx: set GPIO reset line for Ubiquiti NanoStation Loco XW
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-04 11:41:50 +01:00
Felix Fietkau
106a4605c8 ar71xx: add support for configuring at803x PHY GPIO reset via platform data
Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW,
because ar71xx is not converted to device tree yet.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-04 11:41:50 +01:00
Matthias Schiffer
a15ea362d7
ar71xx: fix syntax error in /lib/ar71xx.sh
Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.

Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-29 19:53:47 +01:00
Matthias Schiffer
9a5801e7f6
ar71xx: add model detection for UBNT Rocket Ti
Based-on-patch-by: Neal Oakey <neal.oakey@bingo-ev.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-29 15:37:39 +01:00
Felix Fietkau
1cd7ff3e96 ar71xx: remove squashfs-64k rootfs image from bin directory, the generic one is enough
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 10:20:27 +01:00
Felix Fietkau
eff858e8df ar71xx: remove split kernel/rootfs images where the sysupgrade image can be written to flash directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 10:20:27 +01:00
Felix Fietkau
cc550d0005 ar71xx: remove 2MB flash variant of WP543
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:55:05 +01:00
Felix Fietkau
12e2beaaed ar71xx: remove legacy devices that cannot be supported due to kernel partition size limits
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:51:57 +01:00
Felix Fietkau
35dda35114 ar71xx: remove legacy gzip images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:44:39 +01:00
Felix Fietkau
88f6f0120d ar71xx: remove obsolete jffs2 image building code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:44:39 +01:00
Piotr Dymacz
6998b8a054 ar71xx: move DomyWifi DW33D to nand subtarget
This device uses NAND FLASH, so it should be kept in nand subtarget.

Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-24 22:37:40 +01:00
João Chaínho
39433bb618 ar71xx: Fix switch config on Mikrotik RB450/G
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2016-11-21 10:11:37 +01:00
Piotr Dymacz
e33dcd1cfe ar71xx: add support for YunCore CPE830
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.

Use the same flash approach as for YunCore AP90Q.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
eb9ba2b91e ar71xx: add support for YunCore CPE870
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:

- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset

Vendor firmware access (login/password): Admin/5up

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
01dda0659e ar71xx: add support for YunCore AP90Q
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Flash instruction under vendor fimrware, using telnet/SSH:

1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
31952dbd1c ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530N
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.

All 3 devices are based on Qualcomm/Atheros QCA9531 v2.

COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Paul Wassi
6e65576f2d ar71xx: fix drivers/mtd/nand/ar934x_nfc.c
Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw.
Add *page* in the argument list and remove the local variable.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-11-18 21:57:19 +01:00
João Chaínho
5dd13c071b ar71xx: enable serial console on mikrotik devices
This patch enables the serial console on some Mikrotik devices (RB450,
RB450G, RB493G, RB750UP).

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2016-11-18 09:41:14 +01:00
Stijn Tintel
8e47655d4e kernel: update kernel 4.4 to version 4.4.32
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-11-16 17:31:29 +01:00