Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This adds the patch submitted to upstream that adds BQL to the mvneta
driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under
load when the physical link is saturated.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Parameters for dwc2 on lantiq.
A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Device tree binding for dwc2 usb driver on danube.
Leave old ifxhcd-danube driver as an alternative.
Also adds dr_mode = "host" to eliminate warning on boot.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60
Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port
More info can be found at https://wiki.openwrt.org/toh/meraki/mx60
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Update patch to remove pipetypes var declaration which was throwing
unused variable warning due to the original patch removing the only use.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw.
Add *page* in the argument list and remove the local variable.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This fixes parsing partition placed after TRX with block-aligned length.
It's important e.g. for Archer C9 which has TRX with kernel only and
rootfs as separated partition.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix build on targets not using CONFIG_MODULE_STRIPPED.
Neither RTL8367_DRIVER_DESC nor RTL8367B_DRIVER_DESC are defined
anywhere. It worked for targets using CONFIG_MODULE_STRIPPED since our
module stripper no-ops the various module info macros.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Change grub's root device to xen/xvda,msdos1 for the x86_xen_domu
target so that it will boot without further changes.
Signed-off-by: Wilfried Klaebe <w+lede-project@chaos.in-kiel.de>
[Jo-Philipp Wich: fixed and rebased patch from FS#264, added subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch refreshes the ipq806x kernel patches.
There was a large PR for ipq806x in the queue when the kernel patches
were refreshed for 4.4.32, so currently there is quite much fuzz for
ipq806x.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a powerful API for parallel crypto from which many other modules
can benefit. It only winds up being turned on on SMP systems, which
means this adds 0 bytes to the kernel on tiny machines, while only
adding a small bit to SMP systems for big performance improvements.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Adds Google's mirror as primary source and kernel.org as fallback.
Same as commit 0d4f02dfd6
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
In Device/ls1012ardb IMAGES variable, there are two separate firmware
references to the same packages, while do mult-job compile, the same package
build process will arise conflict occasionally. So, only reserve one ext4 fs
as the default firmware.bin.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
OpenMesh devices have often LEDs which are not yet used by OpenWrt. These
should still be available as disabled LEDs in the system configuration for
easier modification.
Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com>
[sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh,
add wifi/status LEDs]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
MMC support has been added to x86-64 a while ago, there is no reason not
to support it in x86-generic as well.
Signed-off-by: Andreas Ziegler <github@andreas-ziegler.de>
[Matthias Schiffer: add commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
PATA support has been removed from x86-generic without any note in LEDE
r538. Not including them makes the generated images incompatible with older
(and some newer) hardware without any significant gain.
Add it back, and also add the same drivers (as far as available) to x86-64.
Signed-off-by: Andreas Ziegler <github@andreas-ziegler.de>
[Matthias Schiffer: add back x86-generic, update commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.
Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Without setting the HSR to the selected channel, the WLAN of the UAP
Outdoor+ will exhibit high packet loss in RX.
Based-on-patch-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The marvell,88e6352 and marvell,88e6172 compatible strings are used in
target/linux/generic/files/drivers/net/phy/mvsw61xx.c. No idea why grep
missed them when I searched for them.
Thanks to Syrone Wong for noticing and reporting my mistake.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All compiled device tree files not mentioned are binary identical to the
former ones.
Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts.
Due to the include of the input binding header, the BTN_* node names in:
- ramips/GL-MT300A.dts
- ramips/GL-MT300N.dts
- ramips/GL-MT750.dts
- ramips/Timecloud.dts
will be changed by the compiler to the numerical equivalent.
Move the binding include of lantiq boards to the file where they are
used the first time to hint the user where the values do come from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes invalid device tree parameters.
Drop the mvsw61xx node used in mvebu device tree source files. It looks
like some kind of ethernet switch cargo cult. Neither the
marvell,88e6352 nor the marvell,88e6172 compatible strings can be found
in any LEDE file or in the kernel sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This special dwc2 device definition for the Netgear WNDR4700
has been replaced by amcc,usb-otg-405ex.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch moves the common SoC device tree entries
from the currently four supported platforms into a
common apm82181.dtsi.
Furthermore, this patch also changes the GPIO, IRQ and
input definitions of the supported platforms to use the
defined dt-bindings macros for GPIO_ACTIVE_LOW|HIGH,
KEY_WPS|RESTART|*, IRQ_TYPE_* when it's appropriate.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the amcc,usb-otg-405ex device
which is found in all APM82181 SoCs.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
As specified by e0229a16b0 if the VR9
based router provides FXS ports and they should enabled then the
following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M
By adding mem= parameter a pci device stop working correctly. The
pci-lantiq.c module use get_num_physpages() to compute dynamically the
memory amount of the board.
The mem= make the module to compute in the wrong way the BAR11MASK, so
in this situation the mask is misaligned with the dma area that the
hardware expects.
This patch is a port of what legacy ifxmips_pci.c does.
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
The latest stock firmwares for US and EU regions have started checking the
region code.
Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some builders have troubles cloning the boot-wrapper-aarch64.git repository so
provide a mirror checksum to allow downloading from sources.lede-project.org
instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.
The MAC address numbering of the TEW-691GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:0C
WIFI: AA:BB:CC:DD:EE:0D
WAN: AA:BB:CC:DD:EE:0F
The MAC address numbering of the TEW-692GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:e4
WAN: AA:BB:CC:DD:EE:e5
2.4GHz: AA:BB:CC:DD:EE:e7
5 GHz: AA:BB:CC:DD:EE:e8
Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.
Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.
Set the label and compatible string according to the the PCI binding
documentation.
Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.
Use the usual eeprom for the soc wmac of the Dovado Tiny AC.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set a device specific wireless mac address for ARV7506PW11, VGV7519 and
VGV7510KW22. The one from the EEPROM is a generic one and the same on
all boards.
Use the wifi@0,0 label and the pci0,0 compatible string for the
ARV7519PW and ARV7525PW since the pci vendor and device id is unknown.
It should work anyway since the compatible string isn't evaluated
(yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
