Commit graph

19636 commits

Author SHA1 Message Date
Koen Vandeputte
ba2b0f0ac6 kernel: bump 4.14 to 4.14.54
Rereshed all patches

Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-11 16:02:24 +02:00
Rafał Miłecki
7ddba08d87 kernel: bcm47xxpart: fix getting user-space data partition name
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.

This fixes UBI support for devices that have kernel flashed on partition
with a bad block.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-10 14:05:02 +02:00
David Bauer
6476148034 ath79: add support for OCEDO Raccoon
This commit adds support for the OCEDO Raccoon

SOC:	Atheros AR9344
RAM:    128MB
FLASH:  16MiB
WLAN1:  AR9344 2.4 GHz 802.11bgn 2x2
WLAN2:  AR9382 5 GHz 802.11an 2x2
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

	NOTE: The U-Boot won't boot with the serial attached.
	Boot the device without serial attached and attach it
	after 3 seconds.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-07-08 00:04:27 +02:00
Hauke Mehrtens
da6c09eff4 kernel: move CONFIG_USB_MTU3 to generic config
CONFIG_USB_MTU3 is not visible for the mediatek target by default, but
only when CONFIG_USB_GADGET is set. This will config option will be
remove with when running "make kernel_oldconfig", move this option to
the generic config to prevent this.

This fixes the build of the mt7623 subtarget of the mediatek target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-07-07 23:53:04 +02:00
Hauke Mehrtens
29fa9ac559 kernel: disable some DRM_PANEL config options
The modules should not be build by default.
This fixes the build of the zynq target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-07-07 23:53:04 +02:00
Lucian Cristian
2d268c0710 ath79: disable unused drivers for tiny target
Shrink the tiny kernel by moving all switch and ethernet phy drivers to
the generic kernel config instead of the target kernel config.

All boards in the tiny and nand target are either ar7240 or ar9331 based,
which don't support external xMII and therefore no external ethernet phy
can be connected. None of the boards uses a realtek switch either.

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-07 21:07:40 +02:00
Lucian Cristian
80e3a16fda ath79: optimize ath79 tiny target for size
the speed impact on tiny target is minimal and worth the size gained

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-07 21:07:40 +02:00
Christoph Krapp
e420b7b5c5 ath79: add support for UniFi AC-Mesh Pro
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-07 21:07:40 +02:00
Ademar Arvati Filho
16d6a63f85 ramips: add support for Blueendless Kimax U35WF
Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet

Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908
Based on: https://github.com/lede-project/source/pull/965

Specification:
- SoC: MediaTek MT7620N
- CPU/Speed: 580 MHz
- Flash-Chip: KH25L12835F Spi Flash
- Flash size: 16 MiB
- RAM: 64 MiB
- LAN: 1x 100 Mbps Ethernet
- WiFi SoC-integrated: 802.11bgn
- 1x USB 2.0
- UART: for serial console

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
3. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-07 21:07:40 +02:00
Mathias Kresin
a28d686fb6 ar71xx: factor out safe loader image build code
Add a template for safeloader images and include it instead of
overwriting variables defined in the common tp-link build commands.

Split the existing tp-link templates to proper implement the safeloader
template.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin
b908c82f49 ar71xx: drop unnecessary LOADER_TYPE variables
Drop the LOADER_TYPE variables in case no loader is used at all or move
the variable to devices which are using a loader.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin
a0ec632f8d ar71xx: get rid of copy-file
Use the provided image build variables to point the kernel-bin build
command to the kernel we are interested in.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin
5260c1003c ar71xx: mikrotik: cleanup nand image build code
Use the LOADER_TYPE variable to specify that we need the elf preloader
and append the loader via the corresponding build recipe. It allows to
enable initramfs images again for mikrotik NAND images, which caused a
build error before.

Add the minor header only to the kernel of the sysupgrade images, as it
is only required for the bootloader to find the kernel on flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
INAGAKI Hiroshi
0b83a23560 ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Stock firmware:

In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.

(excerpt from dmesg):

MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"

The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.

If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.

(example):

## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1  !!
## Booting image at bc060000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.50
   Image Type:   MIPS Linux kernel Image (lzma compressed)
   Data Size:    1865917 Bytes = 1.8 MB
   Load Address: 80001000
   Entry Point:  80001000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!

Starting kernel ...

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-07 21:07:40 +02:00
Daniel Engberg
3accbc6aac sunxi: Enable SD block devices
USB storage support is however SCSI Disk block device support isn't
meaning that connected devices wont enumerate.
Enable CONFIG_BLK_DEV_SD by default to fix it.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2018-07-07 18:19:39 +02:00
Alexandru Ardelean
7de50d1917 brcm2708: platform.sh: fix tar directory directive
BusyBox's `tar` command does not support the `--directory` directive, which
is essentially `-C` in short-form option.
BusyBox's `tar` command supports `-C`.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
2018-07-07 18:19:39 +02:00
Luis Araneda
8f60c3d571 kernel: remove DEVMEM and DEVKMEM from target's config
These options are handled by generic configuration

Targets that need these options should select KERNEL_DEVMEM
and/or KERNEL_DEVKMEM options on OpenWRT's config

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-07-07 18:19:39 +02:00
Tim Small
e97aaf483c WDR4900v1 remove dt node for absent hw crypto.
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC.  However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines.  If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.

This commit overrides the incorrect dt node definition in the included
file.

See also:
 - https://bugs.openwrt.org/index.php?do=details&task_id=1262
 - https://community.nxp.com/thread/338432#comment-474107

Signed-off-by: Tim Small <tim@seoss.co.uk>
2018-07-07 18:19:39 +02:00
Antti Seppälä
9f451ec698 kernel: usb: dwc2 DMA alignment fixes
Add two patches submitted for upstream review that significantly improve
the dwc2 driver on openwrt from kernel stability and performance
perspectives.

Fixes: FS#1367

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
2018-07-07 18:19:39 +02:00
Felix Fietkau
c3bdb89e61 kernel: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-07 14:53:26 +02:00
Koen Vandeputte
d0839e020d kernel: bump 4.14 to 4.14.53
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-04 14:16:37 +02:00
Koen Vandeputte
01ca20cdfd kernel: bump 4.9 to 4.9.111
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-04 14:16:37 +02:00
Christoph Krapp
8722c52b41 ath79: remove bs-partition ro-flag for UniFi AC devices
This removes the read-only flag from the bs (bootselect) partition
on UniFi AC devices. This allows to correct the indicator from which
partition the device is booting its kernel from.

See also:
 - freifunk-gluon/gluon#1301
 - https://bugs.lede-project.org/index.php?do=details&task_id=662

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-04 01:20:03 +02:00
Aleksandr V. Piskunov
63c9081c77 ath79: swap TP-Link Archer C7 v2 USB port LED and GPIO names
TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order,
i.e. in order to match actual user visible labels, usb1 should be usb2,
and vice versa.
This patch swaps LED and GPIO power control node names.

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
2018-07-04 01:20:03 +02:00
Mathias Kresin
31aa62c5ec ath79: drop mv88e6063 switch driver
Due do a missing KCONFIG isn't selectable nor enabled in the target
kernel config. Drop it for now and enable/add the driver at the time it
is required.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-04 01:20:02 +02:00
Aleksandr V. Piskunov
36fea5a7b9 ipq806x: fix numbering for Netgear R7800 LAN ports
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-07-04 01:20:02 +02:00
Romain MARIADASSOU
ce31bdc20c ramips: add support for TL-WA801ND v5
Specification:

- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn

Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.

Flash instructions:

1) To flash the recovery image, start a TFTP server with IP address
   192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
   button and power it up. Keep pressing the WPS/Reset button for
   10 seconds or until the lock LED is lighting up.
   It will try to download the recovery image and flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-07-04 01:20:02 +02:00
Maxim Anisimov
7d07bc96b7 ramips: add support for ZyXEL Keenetic Extra II
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button

The device supports dual boot mode. So we use only first half of flash.

Flash instruction:

The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
   to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Maxim Anisimov
9e2c28472c ramips: move zyimage define to common Makefile
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Tobias Schramm
faf64056dd ramips: add support for MikroTik RouterBOARD RBM11g
This commit adds support for the MikroTik RouterBOARD RBM11g.

=Hardware=

The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.

==Switch==

The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.

==Flash==

The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.

==PCIe==

The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.

==USB==

There are no external USB ports.

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.

==Serial port==

The device does have an onboard UART on an unpopulated header next to the
flash chip:

GND: pin 2
 TX: pin 7
 RX: pin 6

Settings: 115200, 8N1

See below illustration for positioning of the header.

0 = screw hole
* = some pin
T = TX  pin
R = RX  pin
G = GND pin

Pinout:
+---------------
|O
|             __
|            /  \
|            \__/
|
|
|
|               +---+
|               |RAM|
| +--+          |   |
| |**|  <- unpopulated header with UART
| |*T|          +---+
| |R*|        +--------+
| |**|        |        |
| |G*|        |  CPU   |
| +--+        |        |
|    +--+     |        |
|    |  |     +--------+
|    +--+  <- flash chip
|O
|       +-----+
|       |     |
|+--+   |     |
||  |   |     |
+---------------------

=Installation=

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**

When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
   initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot

Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
   to the device using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"

Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-07-04 01:20:02 +02:00
Michael Kuron
d0b89e48d7 lantiq: enlarge AVM Fritz!Box 3370 flash
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.

Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.

Available flash space for rootfs+overlay increases from 48MB to 124MB.

Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.

Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.

Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.

Signed-off-by: Michael Kuron <m.kuron@gmx.de>
2018-07-04 01:20:02 +02:00
Mathias Kresin
f72605f70e lantiq: backport stp-xway get callback implementation
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.

Fixes: FS#1620

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-04 01:20:01 +02:00
Mathias Kresin
eccde89aa4 kernel: fix AT8032 PHY phy id mask
Don't mask bit 4 of the AT8022 phy id. If bit 4 of the AT8022 phy id
(0x004dd023) is masked, it will match the phy id of the AR8327 switch
(0x004dd033) as well.

It results in applied at803x driver settings/callbacks, which will at
least limit the AR8327 phys to 100MBit operation instead of the possible
1000MBit.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-04 01:19:05 +02:00
Kevin Darbyshire-Bryant
3698b34a00 kernel: gen_stats: Fix netlink stats dumping in the presence of padding
Backport hot off the press upstream netlink patch.  Fixes stats display
from CAKE qdisc on MIPS allowing us to bump CAKE to latest version.

The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.

However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.

Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-07-03 11:40:18 +01:00
Felix Fietkau
09b6755946 ramips: limit dictionary size for lzma compression
In some cases, recent builds fail to boot from flash with at least some
MT7621 based devices. The error message is:
"LZMA ERROR 1 - must RESET board to recover"
Booting the same kernel via TFTP works for some reason.

Through testing I figured out that limiting the LZMA dictionary size
seems to prevent these errors

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-03 11:18:39 +02:00
Luis Araneda
efa112261b zynq: remove config options handled by generic
The options are now handled for all targets by
the generic configuration

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-07-02 07:12:48 +02:00
Peter Lundkvist
781ad46206 ath79: add support for TP-Link RE450 v2
TP-Link RE450 v2 is a dual band router/range-extender
based on Qualcomm/Atheros QCA9563 + QCA9880.

Specification:

- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button
- UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers)

Flash instruction:
Apply factory image in OEM firmware web-gui.

U-Boot does not seem to have any recovery functions, so
debricking requires connection via UART.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-07-02 07:05:33 +02:00
Koen Vandeputte
f4ac88b509 kernel: bump 4.14 to 4.14.52
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-02 07:04:48 +02:00
Koen Vandeputte
8e622aae58 kernel: bump 4.9 to 4.9.110
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-02 07:04:34 +02:00
Rocco Folino
4ff019722c ath79: port TP-Link TL-WR741ND v4 and TL-WR740ND v4
This patch ports the TP-Link TL-WR741ND v4 and TL-WR740ND v4 to the
ath79 target.

Because the two devices share the same hw layout, this patch adds a common
.dtsi which is included by the two .dts.

Signed-off-by: Rocco Folino <rocco@folino.io>
2018-07-02 07:03:21 +02:00
Rocco Folino
9b575288eb ath79: add pinmux to ar9330
This patch adds the pinmux support to the ar9330 used to disable the
JTAG or to enable switch LEDs

Signed-off-by: Rocco Folino <rocco@folino.io>
2018-07-02 07:00:20 +02:00
Lev
3d6f57f3c6 ramips: fix wizfi630a swapped lan/wan port
The order of the Ethernet ports were mixed up.
This commit fixes the order to be aligned with the physical layout.

Signed-off-by: Lev <leventelist@gmail.com>
2018-07-02 06:59:31 +02:00
Adrian Schmutzler
4456dd4660 ath79: add support for Unifi AC Mesh
The Unifi AC Mesh is equivalent to the Unifi AC Lite. However,
for setting certain parameters with the flashed device it is
helpful that the devices know their variant (e.g. automatically
setting antenna gain for the different antennas in Lite and Mesh).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-28 20:31:48 +02:00
Dmytro Smyrnov
40218a2632 ath79: add support for more AR7241 TP-Link boards
Its common AP99(AR7241) platform with following devices:

  TP-Link TL-WR841N/ND v7 (SoC AR7241 / Wifi AR9287 / without USB)
  TP-Link TL-MR3220 v1 (SoC AR7241 / Wifi AR9285 / USB support)
  TP-Link TL-MR3420 v1 (SoC AR7241 / Wifi AR9287 / USB support)

Signed-off-by: Dmytro Smyrnov <dioptimizer@hotmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 20:31:47 +02:00
Lucian Cristian
25070f7106 ath79: small wr1043nd-v4 fixes
- fix sysupgrade check
- move usb to v4 dts because v5 doesn't have it
- make wan mac address behave like ar71xx target
- add orange wan led support, it can be userspace activated like:

  on:
  echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger

  off:
  echo none > /sys/class/leds/tp-link\:orange\:wan/trigger

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-28 20:31:03 +02:00
Lucian Cristian
7dd3d7e1d3 ath79: add support for Ubiquiti UniFi AC-Pro
rework the dts to a common unifi-ac dtsi
pro network is connected via phy0 and has usb ports
lite network is connected via phy4 without usb ports

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-28 18:39:57 +02:00
Adrian Schmutzler
56fddc2577 ath79: sync naming of Ubiquiti devices
Use a Unifi AC Lite board-/image name consistent with other Ubiquiti
devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-28 18:39:57 +02:00
Chuanhong Guo
c463320812 ath79: Remove all memory nodes defined in dts
This target can automatically detect the correct memory size and we've
been using it for long in ar71xx.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-28 18:39:57 +02:00
Mathias Kresin
a570933999 treewide: gpio-export: add error handling
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Mathias Kresin
750e4b62b1 ipq806x: drop gpio export patch
The hack isn't used by any board.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Stefan Lippers-Hollmann
7c7ca66109 ipq806x: switch the NBG6817 wlan LEDs from amber to white
The original device support patch configured the amber wlan LEDs (which
are meant as error indicator by the OEM) controlled by the SOC's GPIO
as wlan traffic indicators, as the correct white wlan LEDs are
connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were
not accessible. The recent addition of GPIO/ LED support to ath10k now
makes it possible to use the correct white LEDs instead - and
"mac80211: ath10k: use tpt LED trigger by default" also enables them by
default. While both LEDs are independent of each other (two separate
LEDs sharing one light tunnel), triggering both on wlan traffic is not
the intended behaviour (bright yellow light).

Tested on the ZyXEL NBG6817.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-06-28 18:39:57 +02:00
Andrey Jr. Melnikov
19c7e950af ramips: move mt7620n i2c_pins definition to right place
Move to i2c pins pinmux node to the pinctrl node.

Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")

Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Hannu Nyman
7b74b40fe9 ipq806x: remove "firmware" partition definition from netgear routers
Remove the "firmware" partition definition from the DTS of R7800
to fix sysupgrade.

Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x
and that causes mtd to misbehave as additional kernel and ubi
partitions are detected from inside the "firmware" partition.
  [    1.111324] 0x000001480000-0x000001880000 : "kernel"
  [    1.121005] 0x000001880000-0x000007900000 : "ubi"
  [    1.283912] 0x000007900000-0x000008000000 : "reserve"
  [    1.296407] 0x000001480000-0x000007900000 : "firmware"
  [    1.468043] no rootfs found after FIT image in "firmware"
  [    2.426860] 2 uimage-fw partitions found on MTD device firmware
  [    2.426931] 0x000001480000-0x000001880000 : "kernel"
  [    2.440420] 0x000001880000-0x000007900000 : "ubi"

Both kernel and ubi are already defined in DTS, so this duplication
leads into errors in sysupgrade:
  Writing from <stdin> to kernel ...
  ubiattach: error!: strtoul: unable to parse the number '6 mtd10'
  ubiattach: error!: bad MTD device number: "6 mtd10"

The partition is defined to same area as kernel+ubi, and is not
needed for sysupgrade anymore. Remove it to fix things.

Only tested for the R7800 but all of them should behave equal.

Fixes: FS#1617

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[squashed commits, add "tested on" note]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-27 22:11:06 +02:00
INAGAKI Hiroshi
0efd0308a0 ramips: add switch port index for I-O DATA WN-GX300GR
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0

1-4: lan
0: wan

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-27 08:42:54 +02:00
Lucian Cristian
4ec9763ee9 firmware-utils: tplink-safeloader: switch tl-wr1043nd-v4 to dynamic partitions
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-27 08:42:54 +02:00
Christian Lamparter
82618062cf ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617

Hardware highlights:

SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR:    32 MiB Macronix MX25L25635F
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS:   Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS

Serial:
	WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
	The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
	pre-soldered. Pinout:
	  1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX

first install / debricking / restore stock:
 0. Have a PC running a tftp-server @ 192.168.1.99/24
 1. connect the PC to any LAN-Ports
 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
    into the tftp-server root directory and rename it to just "ras.bin".
 3. power-cycle the router and hold down the the WPS button (for 30sek)
 4. Wait (for a long time - the serial console provides some progress
    reports. The u-boot says it best: "Please be patient".
 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
    flashes fast at the same time. You have to reboot the device and
    it should then come right up.

Installation via Web-UI:
 0. Connect a PC to the powered-on router. It will assign your PC a
    IP-address via DHCP
 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
 2. Go to the "Expert Mode"
 3. Under "Maintenance", select "Firmware-Upgrade"
 4. Upload the OpenWRT factory image
 5. Wait for the Device to finish.
    It will reboot into OpenWRT without any additional actions needed.

To open the ZyXEL NBG6617:
 0. remove the four rubber feet glued on the backside
 1. remove the four philips screws and pry open the top cover
    (by applying force between the plastic top housing from the
    backside/lan-port side)

Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|   Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

|NBG6617> HELP
|ATEN    x[,y]     set BootExtension Debug Flag (y=password)
|ATSE    x         show the seed of password generator
|ATSH              dump manufacturer related data in ROM
|ATRT    [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO              boot up whole system
|ATUR    x         upgrade RAS image (filename)
|NBG6617>

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

|NBG6617> ATSE NBG6617
|012345678901

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711

copy and paste the result into the shell to unlock zloader.

|NBG6617> ATEN 1,0046B0017430

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

|NBG6617> ATGU
|NBG6617#

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-26 08:57:26 +02:00
Sibren Vasse
ba74b45476 ath79: add support for TP-Link Archer c7 v2
Signed-off-by: Sibren Vasse <github@sibrenvasse.nl>
2018-06-26 08:57:26 +02:00
Lucian Cristian
2a7e03af37 ath79: add tl-wr2543-v1 support
to switch between wlan leds we need a userspace implementation

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 08:57:26 +02:00
Kevin Darbyshire-Bryant
094d49cddf kernel: bump 4.14 to 4.14.51
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Refresh patches.

Remove patch that can be reverse applied:
mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch
mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch

Update patch that no longer applied:
ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch

Compiled-tested-for: lantiq, ramips
Run-tested-on: lantiq BT hh5a, ramips MIR3g

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Michael Yartys <michael.yartys@protonmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
2018-06-26 08:57:21 +02:00
Zoltan HERPAI
31c26cece3 ath79: add support for ON Networks N150R
This is a rebranded Netgear WNR612v2, specs are the same.

 - Atheros AR7240 (Python) @400MHz
 - flash 4MB
 - ram 32MB
 - ethernet 10/100: 1xwan + 2xlan (only two)
 - radio AR9285

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-06-26 07:05:44 +02:00
Zoltan HERPAI
51dd8ec62f ath79: add Netgear WNR612 v2
Netgear WNR612 v2:
 - cpu Atheros AR7240 (Python) @400MHz
 - flash 4MB
 - ram 32MB
 - ethernet 10/100: 1xwan + 2xlan (only two)
 - radio AR9285

As there is a rebranded WNR612v2 called ON Networks N150R, add
a dtsi which includes all device support, and add a separate dts
for the device only (with a separate one for the subsequent N150R).

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-06-26 07:05:30 +02:00
Alex Maclean
2f23a0583a ramips: RE350: add rootfs offset to header
Have mktplinkfw fill in the rootfs offset so the firmware splitter can
find it without aligning to erase blocks.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-26 07:04:43 +02:00
Franz Flasch
8375623a06 ramips: add support for TP-Link Archer C2
Specification:

- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0

Preparing a TFTP recovery image for initial flashing:

Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!

Create a TFTP recovery image:

1) Download a stock TP-Link Firmware file here:
     https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
     #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
     #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin

The resulting image can be flashed via TFTP recovery mode.

Flash instructions:

1) To flash the recovery image, start a TFTP server from IP address
   192.168.0.66 and serve the recovery image named
   ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
   and power it up. Keep pressing the WPS/Reset button for 10 seconds.
   It will try to download the recovery image and flash it.

It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch
abb7524683 ramips: fix ZyXEL Keenetic Viva switch config
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.

Use the mii-bus property instead to manage the switch via a mdio bus.

Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch
d4ac26ec49 kernel: rtl8366-smi: add Realtek switch management via mii-bus
Current version of rtl8366-smi module only supports Realtek switch
managment via two gpio lines. This adds Realtek switch
management via mii_bus. Tested on a Tp-link Archer C2 v1 (Mediatek
SoC mt7620a based)

dts-file configuration should look like this:

rtl8367rb {
	compatible = "realtek,rtl8367b";
	realtek,extif1 = <1 0 1 1 1 1 1 1 2>;
	mii-bus = <&mdio0>;
};

&ethernet {
	status = "okay";
	mtd-mac-address = <&rom 0xf100>;
	pinctrl-names = "default";
	pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;

	port@5 {
		status = "okay";
		mediatek,fixed-link = <1000 1 1 1>;
		phy-mode = "rgmii";
	};

	mdio0: mdio-bus {
		status = "okay";
	};
};

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Mathias Kresin
f9e7f19334 kernel: rtl8367b: drop redundant compatible
Remove the compatible without vendor prefix. It is formal wrong and not
used in the tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-25 20:52:18 +02:00
Adrian Schmutzler
5c5bf8b865
ar71xx: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:06:31 +02:00
Adrian Schmutzler
2524febf79
ar71xx: Add TP-Link Pharos v2 board detection
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.

Code was written mostly by Alexander Couzens <lynxis@fe80.eu>

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:02:01 +02:00
Axel Neumann
65c05301c2 Re-enable arbitrary IPv6 addresses as outer ip4-in-ip6 tunnel source address
The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches
break the possibility for using an ip4ip6 tunnel interface as a fall
back interface accepting ip4-in-ip6 tunneled packets from any remote
address. This works out of the box with any normal (non-666-patched)
kernel and can be configured by setting up an 'ip -6 tunnel' with type
'any' or 'ip4ip6' and a remote address of '::'.

The misbehavior comes with line 290 the patch which discards all packets
that do not show the expected saddr, even if no single fmr rule was
defined and despite the validity of the saddr was already approved earlier.

Signed-off-by: Axel Neumann <neumann@cgws.de>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-23 09:47:05 +02:00
Kristian Evensen
4def81f30f mediatek: Add support for the UniElec U7623-02
This commit adds support for the MT7623A-based UniElec U7623-02 router,
with eMMC storage and 512MB RAM. The router can be delivered with NAND
Flash and more memory, but I only have access to the one configuration.
The DTS is structured in such a way that adding support for
more/different storage/memory should be straight forward.

The device has the following specifications:

* MT7623A (quad-core, 1.3 GHz)
* 512MB RAM (DDR3)
* 8GB storage (eMMC 4.5)
* 2x normal miniPCIe slots
* 1x miniPCIe slot that is connected via an internal USB OTG port
* 5x 1Gbps Ethernet (MT7530 switch)
* 1x UART header
* 1x USB 3.0 port
* 1x SATA 3.0
* 1x 40P*0.5mm FPC for MIPI LCD
* 1x SIM slot
* 12x LEDs (2 GPIO controlled)
* 1x reset button
* 1x DC jack for main power (12V)

The following has been tested and is working:
* Ethernet switch
* miniPCIe slots (tested with Wi-Fi cards)
* USB 3.0 port
* sysupgrade
* reset button

Not working:
* The miniPCIe connected via USB OTG. For the port to work, some MUSB
glue must be added. I am currently in the process of porting the glue
from the vendor SDK.

Not tested:
* SATA 3.0
* MIPI LCD

Installation:

The board ships with u-boot, and the first installation needs to be done
via the bootloader using tftp. Step number one is to update the MBR of
the eMMC, as the one that ships with the device is broken. Since the
device can ship with different storage sizes, I will not provide the
exact steps for creating a valid MBR. However, I have made some
assumptions about the disk layout - there must be one 8MB recovery
partition (FAT32) and a partition for the rootfs (Linux).

The board loads the kernel from block 0xA00 (2560) and I have reserved
32MB for the kernel (65536 blocks). I have aligned the partitions on the
erase block size (4096 byte), so the recovery partition must start on
block 69632 and end on 86016 (16385 sectors). The rootfs is assumed to
start on sector 90112.

In order to install the mbr, you run the following commands from the
u-boot command line:

* tftpboot ${loadaddr} <name of mbr file>
* mmc device 0
* mmc write ${loadaddr} 0x00 1

Run the following commands to install + boot OpenWRT:

* tftpboot ${loadaddr} openwrt-mediatek-mt7623-7623a-unielec-u7623-02-emmc-512m-squashfs-sysupgrade-emmc.bin.gz
* run boot_wr_img
* run boot_rd_img
* bootm

Recovery:

In order to recover the router, you need to follow the installation
steps above (no need to replace MBR).

Notes:

* F2FS is used as the overlay filesystem.

* The device does not ship with any valid MAC address, so a random
address has to be generated. As a work-around, I write the initial
random MAC to a file on the recovery partition. The MAC of the WAN
interface is set to the MAC-address contained in this file on each boot,
and the address of the LAN-interfaces are WAN + 1. The MAC file is kept
across sysupgrade/firstboot.

My approach is slightly different than what the stock image does. The
first fives bytes of the MAC addresses in the stock image are static,
and then the last byte is random. I believe it is better to create fully
random MAC addresses.

* In order to support the miniPCIe-slots, I needed to add missing
pcie-nodes to mt7623.dtsi. The nodes are just c&p from the upstream
dtsi.

* One of the USB3.0 phys (u3phy2) on the board can be used as either USB
or PCI, and one of the wifi-cards is connected to this phy. In order to
support switching the phy from USB to PCI, I needed to patch the
phy-driver. The patch is based on a rejected (at least last time I
checked) PCI-driver submitted to the linux-mediatek mailing list.

* The eMMC is configured to boot from the user area, and according to
the data sheet of the eMMC this value can't be changed.

* I tried to structure the MBR more nicely and use for example a
FAT32-parition for the kernel, so that we don't need to write/read from
some offset. The bootloader does not support reading from
FAT32-paritions. While the command (fatload) is there, it just throws an
error when I try to use it.

* I will submit and hope to get the DTS for the device accepted
upstream. If and when that happens, I will update the patches
accordingly.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2018-06-22 11:25:52 +02:00
Chen Minqiang
e317bb06fd kernel: cleanup offload hooks on netdev unregister
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-06-22 11:01:42 +02:00
Mathias Kresin
004fe89620 lantiq: fix arcadyan vg3503j switch port indexing
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-21 22:00:03 +02:00
Chuanhong Guo
ed40173dfc ramips: Add support for Phicomm K2G
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-21 22:00:02 +02:00
Tobias Schramm
5684d08741 ramips: Add support for Mikrotik RouterBOARD RBM33g
This commit adds support for the Mikrotik RouterBOARD RBM33g.

=Hardware=

The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.

==Switch==

The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:

port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU

==Flash==

The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.

==PCIe==

The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.

Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:

PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11

==USB==

The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:

open: USB on PCIe 1 is active
closed: USB on rear USB port is active

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.

=Installation=

==Prerequisites==

A USB -> RS-232 Adapter and a null modem cable are required for
installation.

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**

Serial settings: 115200 8N1

The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
   initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
   allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet

On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
   using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"

Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Tobias Schramm
c0167abcb0 ramips: Add lzma-loader targets
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Tobias Schramm
4fa85a625f ramips: Add support for mt7621 to lzma-loader
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Deng Qingfang
feb0a0bf22 ramips: fix Newifi D1 mtd partition
Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-06-21 06:54:42 +02:00
Christo Nedev
48f311a112 brcm2708: Add wifi driver, firmware and NVRAM for Raspberry Pi 3 b
2708 -> 43430 -> pi0w

2709 -> 43430 -> pi3b
2709 -> 43455 -> pi3bplus

2710 -> 43430 -> pi3b
2710 -> 43455 -> pi3bplus

Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
2018-06-20 21:50:14 +02:00
Arvid E. Picciani
bf39d5594b ar71xx: add support for TP-LINK Archer C7 v5
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2018-06-20 15:36:19 +02:00
Daniel Engberg
c6e02b49f6 octeon: Add and set CPU type Octeon+ as default
The lowest CPU type used by supported Octeon platform
is Octeon+ (EdgeRouter Lite) while EdgeRouter Pro/ER-8 uses
Octeon II which is backwards compatible with Octeon+.

Sources:
https://community.ubnt.com/t5/EdgeRouter/EdgeRouter-Pro-CPU/td-p/654599
https://www.cavium.com/octeon-II-CN68XX.html
"OCTEON II family is fully software compatible with the widely-adopted
OCTEON Plus family"

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2018-06-20 15:36:02 +02:00
Daniel Golle
969fe206bd brcm2708: Add wifi driver, firmware and NVRAM for RPi1
Apparently there are RPi1 devices with BRCM43430 wifi, such as the
Pi Zero W. Add the necessary packages for that to the image generated
for those boards as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-20 11:19:26 +02:00
Johann Neuhauser
dcc942e666 ath79: ar934x: use irq-ath79-intc driver and enable wmac
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
Johann Neuhauser
b8562f168b ath79: qca95xx: add new intc2, correct intc3 and add second pcie on qca9557
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
Johann Neuhauser
c7efc93509 ath79: fix irq-ath79-intc driver and add support for other ath79 SoCs
Add the missing enable and disable function.
Remove dummy mask and unmask function and use the one provided by
irq_dummy_chip.
Allow interrupt status register being defined from dts.
Add ddr_wb_flush for ar934x/qca953x.
Rename controller name to qca,ar9340-intc because this design was
first introduced in AR934x.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
INAGAKI Hiroshi
189815462c ramips: add support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
  - MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新(アップデート)")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:21 +02:00
INAGAKI Hiroshi
4645a6d318 ipq806x: add support for NEC Aterm WG2600HP
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

Specification:

- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
  - RX, TX, NC, GND, Vcc from power connector side
  - baudrate: 115200 bps

Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
  /dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
  fw_setenv ipaddr "192.168.0.1"
  fw_setenv serverip "192.168.0.2"
  fw_setenv autostart "yes"
  fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
  bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:01 +02:00
Mathias Kresin
4bb6ee465e ramips: mt7621: fix wireless package selection
Add wpad-mini if wireless drivers are included. Drop the mt76 package if
both of the provided drivers are included with their own packages.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-19 20:45:29 +02:00
Evgeniy Didin
56f3aee531 arc770: bump kernel to 4.14
Currently arc770 is no more "source-only".
Lets update Linux kernel version from 4.9 to 4.14 for arc770.
config-4.14 was simply regenerated with "make kernel_menuconfig".

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
2018-06-19 14:32:47 +02:00
David Ehrmann
81d446b045 ar71x: add support for Mikrotik Routerboard wAP R
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.

Specifications:

- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot

Installation:

1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
  - Boot device: try ethernet once then NAND
  - Boot protocol: DHCP
  - Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
  - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
    server within the same subnet of the DHCP range
  - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
    of the to be booted image, e.g.
    openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
   "try ethernet once then NAND," press and hold the reset button while
   powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
   pressed from the previous step.

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.

Revert to RouterOS

Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: David Ehrmann <ehrmann@gmail.com>
2018-06-19 14:32:47 +02:00
Felix Fietkau
9a4253b81f ramips: improve ethernet driver performance with GRO/TSO
GRO stores packets as fraglist. If they are routed back to the ethernet
device, they need to be re-segmented if the driver does not support
sending fraglists.
Add the missing support for that, along with a missing feature flag that
allows full routed GRO->TSO offload.
Considerably reduces CPU utilization for routing

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-19 09:45:28 +02:00
John Crispin
c49ae68cba ath79: fix qm5p-ac-v2 dts file
Signed-off-by: John Crispin <john@phrozen.org>
2018-06-18 23:23:30 +02:00
David Bauer
b4bf43c667 ar71xx: add support for Fritz!WLAN Repeater 450E
This commit adds support for the AVM Fritz!WLAN Repeater 450E

SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - Most LEDs

Not working:
 - 2 RSSI LEDs
   AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
   control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
   While it is possible to implement this feature, it would require an
   additional kernel patch for a minor functionality.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 23:23:30 +02:00
David Bauer
abb4ab076f ar71xx: fix incorrect speed setting on QCA9556
The QCA9556 only has a SGMII interface. However the speed on the
ethernet link is set for the non-existant xMII interface.

This commit fixes this behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 23:23:30 +02:00
Lucian Cristian
b1a173d7c3 ath79: add support for tl-wr1043nd v2/v3
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 20:29:38 +02:00
Marty E. Plummer
0e81968ee8 ath79: add initial nand support for gl-ar300m
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
2018-06-18 20:29:38 +02:00
Marty E. Plummer
fe3b62bbdc ath79: initial gl-ar300m support
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
2018-06-18 20:29:38 +02:00
Hannu Nyman
414ce80c07 mvebu: enable CONFIG_HW_RANDOM
Enable the Hardware Random Number Generator Core infrastructure
in kernel.

Needed for hardware random number generator drivers like chaoskey

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-06-18 20:29:38 +02:00
John Crispin
ee1dbffeed ipq806x: D7800 only has a single sata port
Signed-off-by: John Crispin <john@phrozen.org>
2018-06-18 20:29:37 +02:00
Vincent Wiemann
076d2ea682 mips: fix dynamic ftrace
The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as
dynamic ftrace depends on -mlong-calls.
See http://patchwork.linux-mips.org/patch/675/
Thus we always set -mlong-calls if the kernel is being
compiled with dynamic ftrace support.

Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
2018-06-18 20:29:26 +02:00
Jeremiah McConnell
e820455198 mvebu: backport ahci_mvebu errata patchset
Marvell ahci hardware requires a workaround to prevent eSATA failures
on hotplug/reset when used with multi-bay external enclosures.

Errata Ref#226 - SATA Disk HOT swap issue when connected through Port
Multiplier in FIS-based Switching mode.

These patches backport the workaround from 4.17.

Signed-off-by: Jeremiah McConnell <miah@miah.com>
2018-06-18 20:28:20 +02:00
Lucian Cristian
c8e76cd4ff ath79: fix rx ring buffer stall qca956x
when ported from ar71xx to ath79 the qca9560-eth was omitted

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 18:21:20 +02:00
Thomas Nixon
bb71a3f27e ar71xx: add kmod-usb-ehci to fix USB on RB hAP AC
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2018-06-18 18:21:20 +02:00
Magnus Frühling
4b280ad91a ipq40xx: add support for ZyXEL WRE6606
Specifications:
SOC:	Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:	128 MB Nanya NT5CC64M16GP-DI
FLASH:	16 MiB Macronix MX25L12845EMI-12G
ETH:	Qualcomm QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:  WPS, Mode-toggle-switch
LED:	Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
        (LAN not controllable by software)
        (WLAN each green / red)
SERIAL:	Header next to eth-phy.
        VCC, TX, GND, RX (Square hole is VCC)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (Correct MAC-address)
 - 2.4 GHz WiFi (Correct MAC-address)
 - 5 GHz WiFi (Correct MAC-address)
 - Factory installation from tftp
 - OpenWRT sysupgrade
 - LEDs
 - WPS Button

Not Working:
 - Mode-toggle-switch

Install via TFTP:

Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.

To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.

append-cmdline patch taken from chunkeeys work on the NBG6617.

Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
2018-06-18 18:21:20 +02:00
Lucian Cristian
71ae0792ba ath79: add tl-wr1043nd-v4 support everything is working
tplink-safeloader: resize kernel partition
kernel 4.14 is much bigger, resize the partition

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 18:21:20 +02:00
Lucian Cristian
cad843e1f5 ath79: add ubiquiti unifi ap ac lite/lr
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 18:21:19 +02:00
Weijie Gao
52109ce71f ath79: ag71xx: fix pll-data setting for ar7242/ar934x/qca955x/qca956x
ar71xx/ar913x series use the old pll registers and settings.

However started from ar7242, a new pll register is introduced and the
pll setting is much simpler.

This can be observed from dev-eth.c from the ar71xx target.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-06-18 18:21:19 +02:00
Weijie Gao
97c5cbc496 ath79: add support for Phicomm K2T
This patch adds dts for qca956x and also support for Phicomm K2T

The qca965x.dtsi adds nearly all the necessary components.
Both ath9k AHB and PCIe worked well.

The Phicomm K2T uses MTD partition 'config' to store the mac addresses in
JSON format. To extract these fields correctly, a script is introduced:
    /lib/functions/k2t.sh
This script provides a helper function to extract mac addresses, and is used
in three places.

Hardware spec of Phicomm K2T:
CPU: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337
WiFi 5.8GHz: QCA9886

Flash instruction:
Apply sysupgrade.bin via serial console:

tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-06-18 18:21:16 +02:00
Chen Minqiang
8f804f42d5 ipq40xx: essedma: fixup ip align
This fixup ip align in essedma driver rx path
see cat /proc/cpu/alignment
which reports alignment-fixups without this fix.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-06-18 15:39:08 +02:00
Kevin Darbyshire-Bryant
d600de3ddd kernel: atm: pppoatm fix vc-mux connection failures
Backport a hot off the press upstream kernel ATM fix:

Preserve value of skb->truesize when accounting to vcc

"There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs. Ideally it would cover ATM too. It doesn't. Just
stashing the accounted value and using it in atm_raw_pop() is probably
the easiest way to cope."

The issue was exposed by upstream with:

commit 14afee4b6092fde451ee17604e5f5c89da33e71e
Author: Reshetova, Elena <elena.reshetova@intel.com>
Date:   Fri Jun 30 13:08:00 2017 +0300

    net: convert sock.sk_wmem_alloc from atomic_t to refcount_t

But an earlier commit left the ticking timebomb:

158f323b9868 ("net: adjust skb->truesize in pskb_expand_head()

Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging
assistance and to David Woodhouse <dwmw2@infradead.org> for further
guidance, cajoling & patience in interpreting the debug I was giving him
and producing a fix!

Fixes FS#1567

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-18 15:27:15 +02:00
Kevin Darbyshire-Bryant
0276e1f760 lantiq: atm: fix ifx_atm driver integration
When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77
we incorrectly updated our hack integration patch that updates atm/common.c

+++ b/net/atm/common.c
@@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc
        write_unlock_irq(&vcc_sklist_lock);
 }

+struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL;
+EXPORT_SYMBOL(ifx_atm_alloc_tx);
+
 static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size)
 {
        struct sock *sk = sk_atm(vcc);

+       if (ifx_atm_alloc_tx != NULL)
+               return ifx_atm_alloc_tx(vcc, size)

The correct solution is to drop our ifx_atm_alloc_tx replacement hack
entirely and let the kernel do its thing.

In reality neither pppoatm or BR2684 interfaces actually hit this code,
so the incorrect integration would only be noticed with direct socket
calls which we are unaware of a use-case.

This is not the solution to pppoatm vc-mux failing to work which started
the whole investigation, but let's fix it up anyway.

With sincerest thanks to David Woodhouse <dwmw2@infradead.org> &
Mathias Kresin <dev@kresin.me>.

Tested-on: lantiq, BT HomeHub 5a

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-18 15:26:41 +02:00
Koen Vandeputte
db73c71e8d kernel: bump 4.9 to 4.9.109
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 15:25:28 +02:00
Rafał Miłecki
93cc44c433 bcm53xx: exit if writing kernel during sysupgrade fails
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-06-18 13:47:08 +02:00
Rafał Miłecki
c3d9109fad bcm53xx: drop not ready support for Luxul devices
Support for these devices isn't ready yet and it was only accidentally
pushed in the commit 0da9303e5b ("mac80211: backport "brcmfmac:
cleanup and some rework" from 4.17").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-06-18 08:46:23 +02:00
Tomasz Maciej Nowak
f5bce268b0 mvebu: replace espressobin spi patch with upstream one
For easier future kernel bumps replace spi patch with upstream version
slightly modified. The modification removes partition definitions which
has been diffrent for some U-Boot versions.
Also this removes unnecessary i2c definition which was in the old patch.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-06-18 07:10:20 +02:00
Tomasz Maciej Nowak
772258044b mvebu: reduce speed to gen1 for espressobin pcie
Since the beginning there's been an issue with initializing the Atheros
based MiniPCIe wireless cards. Here's an example of kerenel log:

 OF: PCI: host bridge /soc/pcie@d0070000 ranges:
 OF: PCI:   MEM 0xe8000000..0xe8ffffff -> 0xe8000000
 OF: PCI:    IO 0xe9000000..0xe900ffff -> 0xe9000000
 advk-pcie d0070000.pcie: link up
 advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
 pci_bus 0000:00: root bus resource [bus 00-ff]
 pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
 pci_bus 0000:00: root bus resource [io  0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
 pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit]
 pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref]
 [...]
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 ath9k 0000:00:00.0: enabling device (0000 -> 0002)
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40
 ath9k 0000:00:00.0: request_irq failed
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 ath9k: probe of 0000:00:00.0 failed with error -22

The same happens for ath5k cards, while ath10k card didn't appear at
all (not detected):

 OF: PCI: host bridge /soc/pcie@d0070000 ranges:
 OF: PCI:   MEM 0xe8000000..0xe8ffffff -> 0xe8000000
 OF: PCI:    IO 0xe9000000..0xe900ffff -> 0xe9000000
 advk-pcie d0070000.pcie: link never came up
 advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
 pci_bus 0000:00: root bus resource [bus 00-ff]
 pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
 pci_bus 0000:00: root bus resource [io  0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
 advk-pcie d0070000.pcie: config read/write timed out

Following the issue on esppressobin.net forum [1] the workaround seems
to be limiting the speed of PCIe bridge to 1st generation. This fixed
the initialisation of all tested Atheros wireless cards.

The change shouldn't affect the performance for wireless cards,
it could reduce the performance of storage controller cards but since
OpenWrt focuses on wireless connectivity, fixing compatibility with
wireless cards should be a priority.

For the record, the iwlwifi and mt76 cards were not affected by this
issue.

1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-06-18 07:10:20 +02:00
Tomasz Maciej Nowak
4ec8c8c23e mvebu: add fix for armada 37xx cpufreq driver
Backport from stable kernel tree fixing clock leak.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-06-18 07:10:20 +02:00
Hauke Mehrtens
6745af9a0d mediatek: mt7622: Do not deactivate CONFIG_BLK_DEV
zram.ko needs CONFIG_BLK_DEV activated and it is by default for all
other targets in OpenWrt.

This makes zram.ko compile again.
Compile tested only.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:19 +02:00
Hauke Mehrtens
10ce015c65 mediatek: mt7622: Do not set CPU_SUBTYPE for Cortex A53
Neon and vfpv4 are mandatory extensions in the ARM64 instruction set
now, do not activate them explicitly. GCC will make use of these
extension now by default.

This makes it possible to share the toolchain with other Cortex A53
SoCs.
Compile tested only.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:19 +02:00
Zoltan HERPAI
1e0aeb2b55 ath79: move Netgear build code into a common makefile
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-06-18 07:10:19 +02:00
Koen Vandeputte
2b9885571b kernel: bump 4.14 to 4.14.49
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86-64
Runtime-tested on: cns3xxx, imx6, x86-64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 07:10:19 +02:00
Koen Vandeputte
8c1f088521 kernel: bump 4.9 to 4.9.108
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 07:10:19 +02:00
David Bauer
4fc005197a ipq40xx: add get_status_led to diag.sh
This commit adds the get_status_led method to diag.sh, which sets the
boot-led as status-led for scripts using this method to get a
status-led.

This method is used platform-independent in downstream project gluon to
set the LED used to indicate the config-mode.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 07:10:19 +02:00
Linus Walleij
1c1e254244 gemini: Cook SQ201 images
This generates the "rd.gz" and "hddapp.tgz" that doesn't contain
anything of the sort but rather the OpenWRT rootfs. It works the
same way as how we generate the same layout for the NAS4220b.
For some reason the ImageInfo file is different for the SQ201.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-18 06:35:33 +02:00
Linus Walleij
d8072a3530 gemini: Add appropriate Wireless kernel modules
The D-Link DIR-685 has a RealTek RT2880 mini-PCI card in a
slot. Activate the appropriate kernel module.

The Square One SQ201 has a Ralink RT61-based mini-PCI card.
Activate the appropriate kernel modules. This fixes the
previous error just activating the firmware: the kernel
module will bring in the firmware it needs.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-18 06:35:16 +02:00
Linus Walleij
dc7f540ce1 gemini: Cook a WRGG firmware image
This makes the Gemini build a WRGG-type firmware update
image for the DIR-685. This should hopefully install the
kernel from the web firmware upgrade API on the product
switching it permanently to use OpenWRT.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-18 06:35:09 +02:00
Rafał Miłecki
0da9303e5b mac80211: backport "brcmfmac: cleanup and some rework" from 4.17
It was described by Arend as:

> This series is intended for 4.17 and includes following:
>
>  * rework bus layer attach code.
>  * remove duplicate variable declaration.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-06-17 22:46:29 +02:00
Rafał Miłecki
e53d0da775 bcm53xx: fix NAND partitions on D-Link DIR-885L
This fixes missing rootfs on above device:
[    2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
(...)
[    2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Fixes: 05cb6aa69f ("bcm53xx: replace linux,part-probe with a proper partitions subnode")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-06-17 22:41:15 +02:00
Johann Neuhauser
14cb05909a ath79: clean up led config script files for all devices
1. Move all status led definitions out of diag.sh into device dt
   as we use here a generic script hook.

2. Encode "phy0ptp" led trigger in dt of device for all ath79 devices.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-16 10:08:51 +02:00
Hannu Nyman
25ea21d765 ath79: fix WNDR3800 support
Fixes for WNDR3800 DTS:
* fix bootcmd
* name art partition to reference it for MACs
* format firmware partition's address similarly as others
* make u-boot-env read-only like in ar71xx
* read wan and lan MACs from art
* fix LED and button gpio values to match ar71xx
  (orange/green powerLED, reset button)
* enable power LED in dts by alias led-status
* define USB LED triggers and connect to USB port
* change wifi button to KEY_RFKILL like in ar71xx

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-06-16 10:08:51 +02:00
Johann Neuhauser
10f8823254 ath79: led-resets: add default-trigger property
Add support for the common led property "linux,default-trigger". It
allows to set a default led trigger via devicetree.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:08:51 +02:00
Lucian Cristian
f7a220b2f6 ath79: fix usb led on wr-1043nd-v1
usb port was not triggered correctly
also remove uneded wifi led trigger from the script

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-16 10:08:51 +02:00
Alex Maclean
ab5b359876 ath79: fixup TL-WR703N/TL-MR10U split
Readd SoC compatible strings and correct model names mangled in
a51078f735, cleanup dts to remove
duplication, rename dtsi for clarity, use correct GPIO for TL-MR10U
USB power.

Tested only on TL-WR703N due to lack of a TL-MR10U.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-16 10:08:51 +02:00
Maxim Anisimov
8956eb502d ramips: add support for TP-Link TL-WR842N v5
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch

Flash instruction:

The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-06-16 10:08:51 +02:00
David Bauer
82fa7b9d78 ramips: use phytpt trigger for mt76 wireless
With this change, the LED trigger is independent from the (wireless)
netdev name. The (wireless) netdev name can be easiliy changed in
OpenWrt and would require an update of the netdev trigger settings each
time it is done.

This change is (for now) applied only to MT7628 devices from TP-Link, as
we only had the possibility to test this change against two of those
devices, namely a TL-WR841 v13 and a Archer C50 v3.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-16 10:08:51 +02:00
lbzhung
291e34edff ramips: fix mt7688 watchdog register base addr
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.

Set the correct register address and size in the dtsi file to get the
watchdog working.

Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:08:51 +02:00
Mathias Kresin
5da2c68d00 ramips: mt7621: fix mtu setting with kernel 4.14
Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device
min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which
is [68, 1500] by default.

It's necessary to set a max_mtu if a mtu > 1500 is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:08:51 +02:00
Daniel Golle
0653e31270 lantiq-vdsl-fw: update to provide recent vectoring firmware
Recent Speedport firmware downloads only work over HTTPS, so the user
either needs to provide the already downloaded file or install
ustream-ssl-* as well as ca-certificates or ca-bundle.

So to get VDSL2 with vectoring on xRX200, simply run
vdsl_fw_install.sh
on the target and either provide the downloaded file as instructed or
make sure the device is connected to the Internet and can download that
HTTPS url itself.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-15 12:45:37 +02:00
Daniel Golle
8e2f8b0c83 Revert "lantiq: get rid of ltq-vdsl-fw"
This reverts commit 0938233fcd.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-15 12:45:37 +02:00
Daniel Golle
037ef13a16 brcm2708: move wifi calibration EEPROMs out of base-files
Ship EEPROM blobs for specific supported board only and don't have them
lurking around in our source tree but rather download them from
@github/RPi-Distro/firmware-nonfree upstream.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-14 18:15:33 +02:00
Daniel Golle
a2f17214cd brcm2708: add brcmfmac-firmware-43455-sdio to DEFAULT_PACKAGES
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-14 13:54:17 +02:00
Daniel Golle
3a40a7d5a5 brcm2708: add RPi3+ wifi calibration data
Add files from
https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.txt
https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.clm_blob

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-14 13:54:17 +02:00
Felix Fietkau
5101515375 kernel: fix conntrack fixup of offloaded flows on timeout
Fixes excessively long conntrack timeout of short lived connections

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-14 11:25:24 +02:00
Felix Fietkau
68ab89854f kernel: fix conntrack leak for flow_offload connections
This was caused by a race condition between offload teardown and
conntrack gc bumping the timeout of offloaded connections

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-13 12:54:45 +02:00
Felix Fietkau
e820734f79 kernel: allow hardware NAT offload drivers to keep a priv pointer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-13 12:54:25 +02:00
Felix Fietkau
ec502cd3fe ramips: rename ethernet driver folder to the same one that upstream uses
Preparation for sharing offload code with the mediatek target through
generic files/

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-13 12:54:25 +02:00
Felix Fietkau
b560c1748a kernel: avoid flow offload for connections with xfrm on the dst entry (should fix IPSec)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-13 12:54:25 +02:00
Kevin Darbyshire-Bryant
f60301db74 kernel: bump 4.9 to 4.9.107
Refresh patches.

Compile-tested for: ar71xx
Run-tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-09 22:39:17 +02:00
Jeremiah McConnell
390c4df2c0 mvebu: enable SATA port multiplier support
Some of the Marvell targets have functional SATA port multiplier
support, which is required for multi-bay eSATA enclosures.  Enable
kernel support by setting CONFIG_SATA_PMP.

Closes: FS#1232 and FS#547

Signed-off-by: Jeremiah McConnell <miah@miah.com>
2018-06-09 16:32:39 +02:00
Matthias Badaire
6ea0807f18 ramips: fix network config for ravpower wd03
This device has only one ethernet port.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[add the existing eth0 as lan block, shorten commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-09 13:45:29 +02:00
David Bauer
daeab36c1b ar71xx: use Power-LED as Diag-LED on FRITZBox 4020
This commit makes use of the Power-LED as Diag-LED, allowing the LED to
work as a status indicator.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:45:29 +02:00
David Bauer
9ec117c5be ar71xx: fix AVM package selection
The AVM package selection partially broke with the addition of the
FRITZ!Box 4020. This commit restores the intended behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:45:29 +02:00
Lucian Cristian
c8677ca89e ath79: add tl-mr3020-v1 support
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-08 12:19:49 +02:00
Karl Palsson
8c15fb5240 ath79: wr1043: fix DTC warnings
Use the "correct" unit name to avoid DTC warnings.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:29 +02:00
Karl Palsson
5e69dce0e7 ath79: glinet ar150: fix DTC warnings
Supply a unit name to match other .dts files and avoid DTC warnings.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson
9dad82c5d6 ath79: ubnt: fix DTC warnings
Use explicit labels instead of units with no reg's to avoid DTC
warnings.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson
93ff973c97 ath79: wdr4300: avoid DTC warnings
Use direct button labels to avoid dtc warnings

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson
29b2804c6b ath79: buffalo_wzr-hp-g450h: fix dtc warnings
Just name buttons directly, rather than abstract and then also a label.
Likewise for leds.  Avoids DTC warnings about unit address with no reg
parameter.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson
97326e5131 ath79: avm_fritz300e: avoid dtc warnings
Use number formats preferred by the device tree compiler

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson
d25d847e78 ath79: mdio: add address-cells and size-cells defaults
Eliminates warnings about relying on defaults from the device tree
compiler.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:27 +02:00
Karl Palsson
35aae0735c ath79: ar9330.dtsi: fix typo in USB unit name
Make the unitname match the reg address.  This fixes a DTC warning.

Tested that USB is still functional on an ar9331 device including this
dtsi.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:27 +02:00
Karl Palsson
1588114cf2 ath79: add etactica-eg200 support
Based on original ar71xx eg200 board files

Tested working:
* usb hub, storage and serial port
* ethernet
* wifi
* leds
* button

sysupgrade from self->self passes validity checks.
sysupgrade from old ar71xx->ath79 passes. (however this doesn't migrate
wireless driver configs)

Only unknown issue is the existance of a /sys/class/leds/ath9k-phy0,
which doesn't "exist"

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:27 +02:00
INAGAKI Hiroshi
a32c06f44d ramips: add support for I-O DATA WN-GX300GR
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.

Specification:

- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Flash instruction using initramfs image:

1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-08 09:56:27 +02:00
Adoal Xu
a51078f735 ath79: add TP-Link TL-MR10U port
Signed-off-by: Adoal Xu <adoalxu@gmail.com>
2018-06-08 09:56:15 +02:00
Sven Eckelmann
4f6320704f ar71xx: Fix offset to WMAC address for 8devices Lima
The ART partition of the Lima board stores exactly three mac addresses:

* 0x0: eth0
* 0x6: eth1
* 0x1002: wmac

The first two are correctly assigned in the mach file but the latter points
to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the
driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when
it doesn't find a valid mac address in the platform_data.

Remove this bogus offset to the ART partition to directly load the wmac via
the EEPROM data in the ART partition.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-06-08 09:39:14 +02:00
Rosen Penev
289b2f5e85 ramips: mt7621: Fix some cosmetic DTC warnings
Node /cpus/cpu@0 has a unit name, but no reg property
Node /cpus/cpu@1 has a unit name, but no reg property
Node /cpuintc@0 has a unit name, but no reg property
Node /cpuclock@0 has a unit name, but no reg property
Node /sysclock@0 has a unit name, but no reg property
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-06-08 09:31:37 +02:00
Rosen Penev
66cc6dd6c4 ramips: mmc: Add back some non-mt7621 code that staging removed
This reverts commit 8a570921b5.

This seems to have been accidentally reverted. This fixes mt7620 and
mt7628.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
2018-06-08 09:31:36 +02:00
Kevin Darbyshire-Bryant
8110bf18f4 ramips: mir3g dts define usb port Vcc volt regulator GPIO
Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.

The GPO is now controlled by the USB driver via the voltage regulator
definition.  The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)

USB port power is enabled on driver load and disabled on driver unload.

Enable kernel support for fixed voltage regulator types on mt7621.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-08 09:31:36 +02:00
Christian Lamparter
4363b5362f ipq40xx: flesh out MR33's pcie dts definitions
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-06-08 09:31:36 +02:00
Christian Lamparter
146fbeb81c ipq40xx: fix OpenMesh A62 dtc warnings
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0 missing ranges for PCI bridge (or not a bridge)
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0 missing bus-range for PCI bridge
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 node name is not "pci" or "pcie"
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 missing ranges for PCI bridge (or not a bridge)
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 incorrect #address-cells for PCI bridge
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 incorrect #size-cells for PCI bridge
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 missing bus-range for PCI bridge
Warning (unit_address_format): Failed prerequisite 'pci_bridge'
Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'

Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-06-08 09:31:36 +02:00
Christian Lamparter
2f1fa04587 ipq40xx: fix dtc warning about /soc/ad-hoc-bus missing a unit name
This patch fixes a dtc warning that shows up for every device
Warning (unit_address_vs_reg): Node /soc/ad-hoc-bus has a reg or ranges property, but no unit name

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-06-08 09:31:35 +02:00
Christian Lamparter
b22e37528b ipq40xx: set #size-cells to 0 to fix warning
qcom-ipq4018-ex6100v2.dtb: Warning (reg_format): "reg" property in
	/led_spi/led_gpio@0 has invalid length (4 bytes)
qcom-ipq4018-ex6100v2.dtb: Warning (avoid_default_addr_size):
	Relying on default #size-cells value for /led_spi/led_gpio@0

Cc: Thomas Hebb <tommyhebb@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-06-08 09:31:35 +02:00
Koen Vandeputte
55b4b1eba0 ar71xx: fix USB switch to mPCIE for Mikrotik rb91x boards
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.

Toggling a gpio selects the output to which USB is connected.

Since kernel 4.9, gpio base is rounded up to a value of 32.

Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.

But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.

Switching the USB port to mPCIe now shows my modem is correctly discovered again:

[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11

Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
2018-06-08 09:31:35 +02:00
Lucian Cristian
a0a616e1b8 ath79: fix qca956x SoC boot
based on old ar71xx irq.c driver

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-07 09:38:52 +02:00
David Bauer
e36f8b3f39 ar71xx: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-07 09:31:58 +02:00
Hannu Nyman
fb8a578aa7 ipq806x: Enlarge R7800 flash - use netgear partition
Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.

Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.

In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.

Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit

Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52

Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-06-07 09:19:39 +02:00
Rosen Penev
fff65dbe24 ipq806x: Limit NR_CPUS to 2
ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:

RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-06-07 09:06:19 +02:00
Koen Vandeputte
2792ef55ab kernel: bump 4.9 to 4.9.106
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-07 09:04:46 +02:00
Catrinel Catrinescu
dc1268cb11 ath79: add WLAN, Ethernet-Switch with LAN/WAN and Status LED to Dorin
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2018-06-07 09:02:04 +02:00
Luis Araneda
32ab2e16b1 zynq: remove support for kernel 4.4
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda
88f7e2386a zynq: switch to kernel 4.14
Also, remove the source-only qualifier

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda
19c3dc60e4 zynq: refresh kernel 4.14 configuration
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda
74dffd592b zynq: copy config to kernel 4.14
The file will be used as a base configuration
for kernel 4.14

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda
61b977fa2c zynq: fix detection of the zybo board
The board_name was being tested for "xlnx,zynq-zybo",
but the .dts compatible string is "digilent,zynq-zybo"

Also, sorted the boards alphabetically, and added an
error message for unsupported boards

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda
7967e6c067 zynq: remove hard-coded network configuration
This is no longer necessary since commit 57776e6
(base-files: remove default /etc/config/network,
generate it via board.d instead)

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda
dfac3ffd07 zynq: reworked image creation process
After commit a1248da (zynq: convert to new image build code),
all boards, became unbootable, entering into a boot loop.

Replace the compressed kernel zImage by an uncompressed Image,
which is compressed after with gzip. Also, enable the creation
of an initramfs image by default.

Change images' filename to match the compatible string from the
respective .dts file (<vendor>_<model>). Also, use the shared
mkits.sh script and remove the target specific one.

Fixes: FS#1204

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Daniel Golle
8796680277 ramips: fix reboot with W25Q256 with 4-address-mode enabled
Some board vendors actually changed the loader to expect the chip
to come up in 4-address-mode and flipped the ADP bit in the flash
chip's configuration register which makes it come up in 4-address-mode.
Hence it doesn't make sense to avoid switching to 4-address-mode on
those boards but the opposite as otherwise reboot hangs eg. on the
WrtNode2 boards. Fix this by checking the ADP register and only using
SPI_NOR_4B_READ_OP on chips which have ADP==0 (come up in 3-byte mode).

See also datasheet section 7.1.11 Power Up Address Mode (ADP)

Fixes: 22d982ea0 ("ramips: add support for switching between 3-byte and 4-byte addressing on w25q256 flash")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-07 02:34:13 +02:00
Matthias Schiffer
0c0bb62999
ar71xx: switch CPE/WBS 210/510 to okli-loader
We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.

While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.

Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.

Fixes: e39847ea2f ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:53 +02:00
Matthias Schiffer
c57e182b56
ath79: lzma-loader: sync with ar71xx target
Import all improvements made in the lzma-loader since development on the
ath79 target started.

This also reverts fe594bf90d ("ath79: fix loader-okli, lzma-loader"), as
is obsoleted by 2ad60168b6af ("ar71xx: lzma-loader: move padding workaround
to gzip step").

Likely, many of the changes should be ported to the ramips lzma-loader as
well, but I don't have a device to test this.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:53 +02:00
Matthias Schiffer
108a6f6792
ar71xx: make loader-okli build step more generic
Add support for different loader types.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:53 +02:00
Matthias Schiffer
9968dcedb4
ar71xx: lzma-loader: constify kernel argv array
By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Matthias Schiffer
8d851a95b7
ar71xx: lzma-loader: set page size to 4KB
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Matthias Schiffer
a28e46b7cc
ar71xx: lzma-loader: move padding workaround to gzip step
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.

This approach had two issues:

- The padding was only working when .data was non-empty (otherwise the
  section would become NOBITS, omitting it in the binary). .data was only
  empty when no CMDLINE was set, leading to further workarounds like
  fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
  workaround was only effective because a missing "const" led to the kernel
  argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
  uncompressed .bin and .elf loaders. The prevented embedding the kernel
  cmdline in the loader for non-gz loader types.

To fix both issues, move the creation of the padding from the linker script
to the gzip step.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Stijn Tintel
e52f3e9b13 kernel: bump 4.14 to 4.14.48
Remove upstreamed patches:
generic/pending/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch
generic/pending/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch
generic/pending/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch
lantiq/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch
Update patches that no longer apply:
generic/pending/811-pci_disable_usb_common_quirks.patch
ath79/0009-MIPS-ath79-add-lots-of-missing-registers.patch

Fixes CVE-2018-6412.

Compile-tested: octeon, x86/64.
Runtime-tested: octeon, x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-06-05 22:54:00 +03:00
Daniel Golle
187da94808 kernel: modules: package module for Exar 8250 UARTs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-05 15:27:36 +02:00
Felix Fietkau
2f3b1dddea kernel: backport patch to fix dst handling for offloaded connections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-05 10:18:58 +02:00
Michael Gray
4fdc6ca31b mvebu: fix broken console on WRT32X (venom)
The console bootarg is being corrupted on boot, causing various issues
including broken sysupgrade.
Utilising the bootargs mangle patch from other targets, hardcode the console
arguments and fetch the rootfs from the bootloader.

Kernel command line: console=ttyS0,115200 root=/dev/mtdblock8

Bootloader command line (ignored): console= root=/dev/mtdblock8

Please cherry pick to 18.06 too

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-06-01 21:01:03 +02:00
Daniel Golle
dcc34574ef oxnas: bring in new oxnas target
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.

Functional issues:
 * PCIe won't come up (hence no USB3 on Shuttle KD20)
 * I2C bus of Akitio myCloud device is likely not to work (missing
   debounce support in new pinctrl driver)

Code-style issues:
 * plla/pllb needs further cleanup -- currently their users or writing
   into the syscon regmap after acquireling the clk instead of using
   defined clk_*_*() functions to setup multipliers and dividors.
 * PCIe phy needs its own little driver.
 * SATA driver is a monster and should be split into an mfd having
   a raidctrl regmap, sata controller, sata ports and sata phy.

Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-01 15:45:06 +02:00
Daniel Golle
17511a7ea8 oxnas: kill old oxnas target
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-01 15:45:06 +02:00
Hans Dedecker
0777a3e773 kernel: re-add export ipv6_push_frag_opts for tunneling now patch
The patch got removed by commit 7dca1bae82 (kernel: bump to 4.9.105)
but is still required as ipv6_push_frag_opts needs to be exported.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-01 14:08:42 +02:00
John Crispin
7197744cd6 Revert "ramips: Move PCI driver to files directory"
This reverts commit a098a78a33.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:20 +02:00
John Crispin
69929dac89 Revert "ramips: Remove redundant owner assignment"
This reverts commit 2ad4daf579.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:14 +02:00
John Crispin
64878a5616 Revert "ramips: improve interrupt mapping"
This reverts commit 5f7396ebef.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:11 +02:00
John Crispin
7577f32c8a Revert "ramips: remove conditional compilation."
This reverts commit 1f78625714.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:09 +02:00
John Crispin
b8569427eb Revert "ramips: remove unnecessary resource details."
This reverts commit edea934799.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:07 +02:00
John Crispin
784943e3f2 Revert "ramips: pci: sync with staging driver"
This reverts commit e07baec9fa.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:05 +02:00
John Crispin
8a570921b5 Revert "ramips: Add back some non-mt7621 code that staging removed"
This reverts commit 048e41f649.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:03 +02:00
John Crispin
1d3c286381 Revert "ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928"
This reverts commit 02f815d190.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:41:51 +02:00
Kevin Darbyshire-Bryant
7dca1bae82 kernel: bump to 4.9.105
Refresh patches.

Drop patches that have been upstreamed:
target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
target/linux/generic/backport-4.9/095-v4.12-ipv6-Need-to-export-ipv6_push_frag_opts-for-tunnelin.patch
target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-01 08:25:14 +02:00
Alex Maclean
5b0c899bfd ath79: correct wmac names in dts
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:23:47 +02:00
Alex Maclean
ba5b6c619b ath79: add TP-Link TL-WR703N port
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:23:28 +02:00
Alex Maclean
d215d0f9ae ath79: add TP-Link TL-WR740N/ND v2 port
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:23:14 +02:00
Alex Maclean
fab3254b32 ath79: add pinmux node to ar724x.dtsi
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:23:02 +02:00
Alex Maclean
34f874b872 ath79: add AR7240 dtsi
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:22:50 +02:00
Alex Maclean
fc8360aa16 ath79: add tiny subtarget
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:22:38 +02:00
John Crispin
c57c3f2c22 ath79: fix glinet ar150 lan/wan ordering
LAN and WAN were swapped

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 08:21:47 +02:00
Daniel Golle
2087df1c6d Revert "kernel: backport export ipv6_push_frag_opts for tunneling now"
This reverts commit daa73b63d5.
The fix has already been imported by
commit b7735d8113 ("kernel: import follow-up fix for previous backport").
The patch won't apply twice.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-01 01:37:51 +02:00
Hans Dedecker
daa73b63d5 kernel: backport export ipv6_push_frag_opts for tunneling now
Patch is required on top of commit 6c81c27efa as ipv6_push_frag_opts needs to
be exported for usage in ip6_tunnel.c

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-05-31 18:29:42 +02:00
Daniel Golle
b7735d8113 kernel: import follow-up fix for previous backport
Buildbots complaining made me wonder what's going on...
ERROR: "ipv6_push_frag_opts" [net/ipv6/ip6_tunnel.ko] undefined!

Fixes: 6c81c27efa ("kernel: backport fix for missing tunnel encapsulation limit option")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-05-31 02:25:59 +02:00
Hans Dedecker
6c81c27efa kernel: backport fix for missing tunnel encapsulation limit option
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-05-30 12:16:24 +02:00
Rosen Penev
9685f39787 ramips: Use generic board detect for GnuBee devices
This is a port of an old commit from mkresin's tree:

09260cdf3e9332978c2a474a58e93a6f2b55f4a8

This has the potential to break sysupgrade but it should be fine as
there is no stable release of LEDE or OpenWrt that support these devices.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:36:02 +02:00
Rosen Penev
976c27f2dd ramips: Fix a few other GnuBee DTS differences
I was carrying a local commit that added the sdhci stuff and missed it
as a result.

Also fix the rgmii3 thing in the PC2 DTS file as that's bogus and causes
a dmesg warning that it's bogus.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:35:24 +02:00
Rosen Penev
02f815d190 ramips: Fix WiFi after 5f7396ebef
That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.

eg. 2.4GHz working but not 5GHz.

As all of these dts entries are already specified in mt7621.dtsi, remove
them.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:33:56 +02:00
Stijn Tintel
64b53247c4 kernel: bump 4.14 to 4.14.44
Refresh patches.

Remove upstreamed patch:
generic/pending/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
Update patches that no longer applies:
generic/hack/901-debloat_sock_diag.patch

Compile-tested on: x86/64.
Runtime-tested on: x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-05-29 00:53:15 +03:00
John Crispin
55f3731002 mediatek: add missing symbols for mt7622
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-28 08:12:28 +02:00
John Crispin
de6162e832 mediatek: add missing symbols
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-27 09:26:13 +02:00
Luo chongjun
312d7a4a5a ar71xx: add support for GL.iNet GL-AR750S
This patch adds supports for GL-AR750S.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2018-05-27 09:26:09 +02:00
Jo-Philipp Wich
3b749d4acc ar71xx: fix bad "proto" references in default network configuration
This change was originally meant to go along with the ucidef_set_interface()
fixup.

Fixes: 7e664b7c2d ("base-files: fix ucidef_set_interface() protocol selection")
Fixes: 85048a9c1f ("base-files: rework _ucidef_set_interface to be more generic")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-25 09:46:55 +02:00
John Crispin
51740777fb mediatek: add mt7622 subtarget
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 22:14:03 +02:00
John Crispin
050da2107a mediatek: backport upstream mediatek patches
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 22:11:55 +02:00
Lucian Cristian
253095131d ath79: initial tl-wr1043nd v1 support
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 15:43:39 +02:00
John Crispin
f7aa08595d kernel: add reset control support to rtl8366 driver
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 15:43:39 +02:00
John Crispin
5a6a32ad9b ath79: fix adjust_link callback for ar9130
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 15:43:39 +02:00
John Crispin
83fb9ec5e0 ath79: make ahb wifi work
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 15:43:39 +02:00
Roman Yeryomin
85048a9c1f base-files: rework _ucidef_set_interface to be more generic
This is a rework of previously submitted patch reworking
ucidef_set_interface_raw [1]. Here, keep the idea but instead
make _ucidef_set_interface more generic and use it instead of
ucidef_set_interface_raw.
Also change the users like ucidef_set_interface_lan and others.

[1] https://patchwork.ozlabs.org/patch/844961/

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-24 09:39:47 +02:00
Koen Vandeputte
467b07e00c kernel: bump 4.14 to 4.14.43
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Michael Yartys <michael.yartys@protonmail.com>
2018-05-24 08:58:17 +02:00
Rosen Penev
8c818fa1f0 ramips: Fix up GnuBee PC1 DTS file a little
There's nothing connected to i2c on this board, so remove it.

Also edited the gpio group to match the PC2 as they're the same.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-24 08:57:33 +02:00
Rosen Penev
048e41f649 ramips: Add back some non-mt7621 code that staging removed
Staging is meant only for mt7621 but for OpenWrt more is needed.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-24 08:57:17 +02:00
Mirko Parthey
7ac238fc98 brcm47xx: add switch port mapping to Asus WL-500W
Switch ports 0..3 are connected to external ports LAN{1..4} in sequence,
switch port 4 is not used, and switch port 5 is connected to the CPU.
The WAN port is attached to the CPU's second network interface; it has no
connection to the internal switch.

Reuse the "Dell TrueMobile 2300" entry, which describes the same mapping.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
2018-05-24 08:57:00 +02:00
John Crispin
f6a067a699 kernel: mark all v3.18 and v4.4 kernels are source-only
These will be removed if not updated to v4.4

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 08:55:52 +02:00
Matthias Badaire
52809db544 ramips: fix to mt7620a and add support for i2c on WD03
There was an error on initial commit, the proper soc is mt7620n (which is
more limited than mt7620a). Moreover, there is a battery management
controller connected to the i2c port of the mt7620n. I have a small piece
of i2c code to get battery level coming.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-22 21:02:01 +02:00
Johann Neuhauser
a7e1e919af ath79: preliminary support for TP-Link WDR3600 / WDR4300 (AR9344)
working:
 - leds
 - buttons
 - lan / wan
 - usb (hub port 1 + 2)
 - wifi 5g
 - sysupgrade
 - ...

not working:
 - wifi 2g

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-05-22 20:53:15 +02:00
Koen Vandeputte
faf0a460c4 kernel: bump 4.14 to 4.14.42
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-22 20:49:08 +02:00
Koen Vandeputte
6c5f2d73e9 kernel: bump 4.9 to 4.9.101
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-22 20:48:43 +02:00
Stefan Lippers-Hollmann
a436ef992d ipq806x: drop "mtd: nand: add Winbond manufacturer and chip"
The W25N01GV NAND is currently not used in any ipq806x device.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:47:20 +02:00
Stefan Lippers-Hollmann
2819732219 ipq806x: drop linux 4.9 support
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
18e9ed2482 ipq806x: switch to linux 4.14
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
8c1c1c4874 ipq806x: remove spi-nor from r7800 dts
There's no spi-nor in R7800, so disable unequipped interfaces.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
96cd31655d ipq806x: remove rpm pinctrl from board dts
These pins seem to be used by hw exclusively, so claiming it in
kernel causes an error in syslog in k4.14+.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
7f694ef3d9 ipq806x: fix EA8500 switch control
EA8500 has pcie2 slot unequipped.
By EA8500 hw design default pcie2 reset gpio (gpio63) is used to
reset the switch. That's why enabling pcie2 brings the switch into
a working state.

So let's just control the gpio63 without enabling the pcie2 slot.

We have to remove the pcie2_pins node so the gpio63 is not defined
twice. Because pcie2 node has a reference to pcie2_pins we have to
remove it as well.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
7a4f9c5993 ipq806x: move mmc specific nodes into v1.0 dtsi
These nodes are common for all revisions so put it into SoC v1.0
dtsi file.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
fbedc2213c ipq806x: fix pcie tx termination offset
According to GPL tarballs and QSDK related branch tx termination
offset for ipq8064 SoC version >= 2.0 should be equal to 0 and
not 7.

https://github.com/paul-chambers/netgear-r7800/blob/master/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L1682-L1685

Fix this.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
d4b98c38c6 ipq806x: apply updated USB PHY settings to v2.0 SoC
USB PHY power settings introduced for ipq8065 SoC with commit
644a0d5 "ipq8065: adjust SS USB PHY power settings"

According to that commit msg and in correspondence to GPL tarballs
and related QSDK branch those settings are applied to ipq8064
SoCs of version >= 2.0.

https://github.com/paul-chambers/netgear-r7800/blob/master/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2507-L2514

Now as we have clarified that mass market boards are of SoC v2.0
move those USB PHY settings from ipq8065 (v3.0 SoC) dtsi to
ipq8064 v2.0 dtsi.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
e16f9abf6b ipq806x: reference ipq8065 as ipq8064 v3.0
ipq8065 is ipq8064 v3.0
> socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0,  hw_plat_ver=65536

Include dtsi accordingly and remove the unneeded qcom-ipq8065-v1.0.dtsi

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
067036e875 ipq806x: move mass market ipq8064 to v2 dtsi
According to OEM bootlog entry mass market devices are ipq8064 SoC
v2.0:
> socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0,  hw_plat_ver=65536

I've checked C2600, EA8500 and VR2600v but couldn't find other
boards bootlog. I think it's safe to assume that other boards are
also v2.0. R7500 may be an exception because it was the first
device to hit the market.

So switch to v2.0 dtsi.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Pavel Kubelun
adbdf78049 ipq806x: introduce ipq8064 SoC v2 dtsi
According to QCA internal numbering there are 3 versions of
ipq8064/5 SoC:
ipq8064 v1.0 - probably ipq8064 evaluation boards only
ipq8064 v2.0 - probably ipq8064 mass market boards only
ipq8064 v3.0 - aka ipq8065, boards based on ipq8065.

Each next revision includes configuration differences from
previous revision and adds something new.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Marc Benoit
e40db2907e kernel: iqp806x low latency kernel does not boot
It keeps failing (R7800) with the stack trace below

BUG: scheduling while atomic: kworker/0:1/26/0x00000002

(unwind_backtrace) from [<c02121d0>] (show_stack+0x10/0x14)
(show_stack) from [<c03932e4>] (dump_stack+0x7c/0x9c)
(dump_stack) from [<c0239b90>] (__schedule_bug+0x5c/0x80)
(__schedule_bug) from [<c05b7260>] (__schedule+0x50/0x3f4)
(__schedule) from [<c05b76a8>] (schedule+0xa4/0xd4)
(schedule) from [<c05ba430>] (schedule_hrtimeout_range_clock+0xc8/0x100)
(schedule_hrtimeout_range_clock) from [<c05ba480>]
       (schedule_hrtimeout_range+0x18/0x20)
(schedule_hrtimeout_range) from [<c05b9f78>] (usleep_range+0x48/0x50)
(usleep_range) from [<c03f333c>] (__clk_hfpll_enable+0x44/0xd0)
(__clk_hfpll_enable) from [<c03f3474>] (clk_hfpll_set_rate+0xac/0xc4)
(clk_hfpll_set_rate) from [<c03ec390>] (clk_change_rate+0xf4/0x1fc)
(clk_change_rate) from [<c03ec510>] (clk_core_set_rate_nolock+0x78/0x94)
(clk_core_set_rate_nolock) from [<c03ec54c>] (clk_set_rate+0x20/0x30)
(clk_set_rate) from [<c0424168>] (dev_pm_opp_set_rate+0x190/0x26c)
(dev_pm_opp_set_rate) from [<c04a8548>] (set_target+0x40/0x108)
(set_target) from [<c04a4.140>] (__cpufreq_driver_target+0x3f4/0x488)
(__cpufreq_driver_target) from [<c04a7494>] (od_dbs_timer+0xcc/0x154)
(od_dbs_timer) from [<c04a7998>] (dbs_work_handler+0x2c/0x54)
(dbs_work_handler) from [<c02309e8>] (process_one_work+0x1c0/0x2f0)
(process_one_work) from [<c02319a8>] (worker_thread+0x2a4/0x404)
(worker_thread) from [<c0235944>] (kthread+0xd8/0xe8)
(kthread) from [<c020eef0>] (ret_from_fork+0x14/0x24)

Signed-off-by: Marc Benoit <marcb62185@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
05f53eecca ipq806x: define KERNEL_SIZE in KB instead of byte for the image generation
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
c3af761e47 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500v2
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500v2.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
c228bbe616 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
45b8a7c1a6 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 D7800
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 D7800.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Tathagata Das <tathagata@alumnux.com>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
0c967d92b3 ipq806x: increase kernel partition size for the TP-Link Archer VR2600v
The default image does not fit 2 MB anymore, expand kernel partition
to 3 MB.

Upgrading should work transparently via sysupgrade in both directions.
Another option would be to merge "kernel" and "rootfs" into a single
"firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the
sizes of the existing partitioning has been deemed safer in the absence
of an actual runtime test on an affected device; the maximum for rootfs
changes from 10.4 MB to 9.4 MB.

This change follows the example for the TP-Link Archer C2600, but has
not been runtime tested on a TP-Link Archer VR2600v.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Sebastian Quilitz <zeraphim@x-pantion.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
b72b36653a ipq806x: increase kernel partition size for the TP-Link Archer C2600
The default image does not fit 2 MB anymore, expand os-image partition
to 4 MB.

Upgrading works transparently via sysupgrade in both directions.
Another option would have been to merge "os-image" and "rootfs" into a
single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just
changing the sizes of the existing partitioning has been deemed safer
and actually tested on an affected device; the maximum for rootfs
changes from 27 MB to 25 MB.

Run-tested on TP-Link Archer C2600.

Signed-off-by: Joris de Vries <joris@apptrician.nl>
[slh: extend comments and commit message, rename rootfs]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
dc50694bd1 ipq806x: increase kernel partition size for the Netgear r7800
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This patch is based on a corresponding change by Pavel Kubelun
<be.dissent@gmail.com> and has been tested by Michael Yartys
<michael.yartys@protonmail.com>

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Ram Chandra Jangir
7ac6697fe2 ipq806x: cleanup kernel config
Disable MSM8960, MSM8974 and APQ8084
 - since these are different SoC's than IPQ806x
Removed unrequired serial configs
 - since ipq806x uses SERIAL_MSM only

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Ram Chandra Jangir
93dd2f7211 ipq806x: add kernel 4.14 support
- Rebased the patches for 4.14
 - Dropped spi-qup and 0027, 0028, 0029
   clk patches since it's already included
   in upstream.

 Tested on IPQ AP148 Board:
  1) NOR boot and NAND boot
  2) Tested USB and PCIe interfaces
  3) WDOG test
  4) cpu frequency scaling
  5) ethernet, 2G and 5G WiFi
  6) ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
David Bauer
70e6ea319d ipq40xx: add eva-image for FRITZ!Box 4040
This commit adds an EVA flashable image for the FRITZ!Box 4040.

The image contains the U-Boot with OpenWRT appended to it. This way we
remove the need to use UART for initial flashing.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
David Bauer
ce91c85e01 ramips: change wifi led trigger for Archer C50v3
This commit alters the TP-Link Archer C50v3 LED settings to use the phy
trigger instead of the netdev one. This way the WiFi status is displayed
even if the wifi interface name is altered.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
David Bauer
35d00d9a41 ramips: fix Archer C50v3 LED mapping
This commit fixes the wrong LED mapping of the Archer C50 v3.
Commit was tested with an EU device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
Lucian Cristian
71cec0b194 ath79: enable rtl8366rb phy
is needed for at least tplink wr1043nd-v1

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-05-22 20:34:14 +02:00
Lucian Cristian
fe594bf90d ath79: fix loader-okli, lzma-loader
booting will hang most of the times on tl-wr1043nd-v1 without a KERNEL_CMDLINE value
add anything as a placeholder as kernel command line is taken from DTS

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-05-22 20:34:14 +02:00
Chuanhong Guo
a789c0f491 ar71xx: Add support for PISEN TS-D084
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0

Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-05-22 07:58:16 +02:00
Sergey Ryazanov
67a3cdcbb0 kernel: enable THIN_ARCHIVES by default
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:20 +02:00
Sergey Ryazanov
bdc2b58c4b kernel: enable FUTEX_PI by default
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:12 +02:00
Sergey Ryazanov
a08b0d0c31 kernel: enable EXPORTFS by default
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:05 +02:00
Sergey Ryazanov
978543a246 kernel: disable DRM_LIB_RANDOM by default
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:57 +02:00
Sergey Ryazanov
ead26e9db6 kernel: disable DMA_{NOOP|VIRT}_OPS by default
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:49 +02:00
Sergey Ryazanov
f928c338ad kernel: disable ARCH_WANTS_THP_SWAP by default
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:42 +02:00
Evgeniy Didin
a2418dba02 arc770: remove source-only
In commit 8b9cdebc9c ("arc770: mark as source-only") arc770 was marked
as source-only because of iproute2 compile issues.
With uClibc-ng version 1.0.30 issues with iproute2 were fixed.
Lets remove "source-only" for arc770 as soon as uClibc-ng version
will be updated to 1.0.30. Patch for uClibc-ng is here:
https://patchwork.ozlabs.org/patch/917547/

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
2018-05-22 07:20:26 +02:00
Hauke Mehrtens
ae8ff1c65c ar71xx: Fix build for dap-1330-a1 board
Using a version number of 16 character causes a buffer overflow in the
version number overwriting the first bit of the signature in the
mkdapimg2 tool.
I am not sure if the version number should be null terminated or not.
This patch reduces the size of the version number by removing the number
of private commits from it.

This was the original version number which caused problems:
OpenWrt-r6727+10
Now it uses this version number:
OpenWrt-r6727

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-05-22 07:20:26 +02:00
Sergey Ryazanov
06116473cc ath25: drop 4.9 kernel support
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:20:13 +02:00
Sergey Ryazanov
5191ea5621 ath25: switch to 4.14 kernel
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 06:42:14 +02:00
Sergey Ryazanov
3d69857ac1 ath25: add kernel 4.14 support
Copy and refresh patches and config from 4.9, no more work is need.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 06:41:57 +02:00
Damir Samardzic
5b7b0c68c7 mvebu: initial support for Marvell Armada 7k and 8k DB boards
Add initial support for cortex-a72 based Armada DB-88F8040-Modular and
DB-88F7040-Modular development boards.

DB-88F8040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU (up to 2 GHz)
- DDR4 DIMM - 64 bits + ECC
- 2 x 128 Mb SPI NOR flash memory
- 2 x 1G Ethernet port via RGMII (RJ45)
- 2 x SD card ports (4 bit port on CP, 8 bit port on AP)
- 2 SERDES modules with the following interfaces each:
  - 2 x SATA Rev 3.0 port (Port1 via SERDES module CON4 (active port), Port0
    via SERDES Module CON2 or CON1 (optional port))
  - 3 x PCI Express (PCIe) Gen 3.0 (Port2 via SERDES module CON5 (active port),
    Port1 via SERDES module CON7 (optional port), Port0 via SERDES module CON6
    (optional port))
  - 2 x USB3 (USB 2.0 backward compatible) host (via SERDES module CON9 and
    CON10)
  - 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 1 x MCI interface by two over USB Type C connector
- 4 x serial COM port driven by the 88F8040 UART interface and converted to
  USB via FTDI IC
- I2C Master Interface
  - CP I2C 2x EEPROM @ Address 0x50 and 0x57
  - 1 x I/O Expander @ Address 0x21
  - Sample at Reset (SatR) memory device @ Address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
  board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions: 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions: 70 mm x 105 mm

DB-88F7040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU
  - CPU core operating speed of up to 1.6 GHz for Dual Core, 1.4 GHz for Quad
    Core
- DDR4 - 32 bit + ECC on Module - SLM1366-V1 (DB-DDR4-40B-MODULE) 4 GByte
  32-bit
- 1 x 128Mb SPI NOR flash memory
- 2 x 1G Ethernet port: 1 over RGMII (RJ45) and 1 over SGMII
- SD card 4 bits port on AP
- eMMc Module on CP
- 1 SERDES Modules with the following interfaces each:
  - 1 x SATA Rev 3.0 port (via SERDES module CON4)
  - 1 x PCI Express (PCIe) Gen 3.0 (via SERDES module CON5)
  - 2 x USB 3.0 (USB 2.0 backward compatible) host (via SERDES module CON9 and
    CON10)
  - 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 2 x MCi interface by one over USB Type C connector
- 4 x Serial COM port driven by the 88F7040 UA
- RT interface and converted to USB via FTDI IC
- I2C Master Interface
  - 2 x EEPROM at address 0x57 and 0x50 in AP and 2 x EEPROM at address 0x57
    and 0x50 in CP
  - 1 x I/O Expander at address 0x21
  - Sample at Reset (SatR) memory device at address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
  board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions - 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions - 70 mm x 105 mm

Booting from USB flash drive (dd sdcard image to the flash drive):
 1. reset U-Boot environment:
      env default -a
      saveenv

 2. prepare U-Boot manually (make sure to set correct dtb file name):
      setenv bootargs_root 'root=/dev/sda2 rw rootdelay=2 ip=dhcp'
      setenv fdtfile armada-7040-db.dtb
      setenv image_name Image
      setenv bootcmd 'usb start; ext4load usb 0:1 $kernel_addr $image_name; ext4load usb 0:1 $fdt_addr $fdtfile; setenv bootargs $console $mtdparts $bootargs_root; booti $kernel_addr - $fdt_addr'
      saveenv
      boot

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-05-21 18:07:47 +02:00
Damir Samardzic
322a02f666 mvebu: initial support for Marvell Armada 3720 DB board
Add initial support for Marvell Armada cortex-a53 based
DB-88F3720-DDR3-Modular development board.

Specifications:
- Dual core ARMv8 Cortex-A53 CPU (up to 1.0 GHz)
- 4Gb 16-bit DDR3/3L DRAM memory
- 128Mb SPI NOR flash memory
- 8Gb eMMC NAND flash memory
- 1 x SATA Rev 3.0 port
- 1 x PCI Express (PCIe) Gen 2.0 or 1 x mini PCI Express (PCIe) Gen 2.0
- 1 x 1G Ethernet port via RGMII (RJ45)
- 1 x SD card port
- 1 x USB3 (USB2 backward) host\device port via type C connector
- 1 x USB2 host port via type A connector
- 1 x serial COM port driven by the 88F3720 UART interface and converted to
  USB via FTDI IC (option to connect the UART DB9 adapter)
- I2C Master Interface:
  - 1 x EEPROM @ address 0x57
  - 1 x I/O Expanders @ address 0x22
  - Sample at Reset (SatR) memory device @ address 0x4C
  - RTC clock generator PT7C4337AWE @ address 0x68
  - USB3 switch PI5USB30213XEA @ address 0x0D
  - ID component of PHY module @ address 0x24
- 1 x JTAG interface for CPU emulator
- 1 x SETM and JTAG debug interface
- 1 x power connector for HDD supply
- 1 x 12V DC jack power connector
- Board dimensions: 150 mm x 179 mm
- LED interface for system status

Booting from SD card:
 1. reset U-Boot environment:
      env default -a
      saveenv

 2. prepare U-Boot with boot script:
      setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
      saveenv

    or manually:
      setenv fdt_name armada-3720-db.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 0; ext4load mmc 0:1 $kernel_addr $image_name;ext4load mmc 0:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr'
      saveenv

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-05-21 18:07:47 +02:00
YuheiOKAWA
13684ba63f kernel: Add support spi-nor, Eon EN25QH32
Support Add spi-nor chip EN25QH32. JEDEC is 1c7016.

Can't boot issue, new revision hardware is EN25QH32 flash chip.
example, MZK-DP150N (ramips).
https://bugs.openwrt.org/index.php?do=details&task_id=1534

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-05-21 18:07:47 +02:00
Alif M. Ahmad
b0a51dab8c x86: disable CONFIG_EFI_VARS
Disable CONFIG_EFI_VARS, since it suffers from sysfs limitation (no
support for variable longer than 1024 bytes).

kmod-fs-efivarfs is the replacement of this, which enables mounting
efivarfs file system and doesn't suffer from 1024 bytes limitation.

Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
2018-05-18 11:19:00 +02:00
YuheiOKAWA
d91953cb53 ramips: add support for YUKAI Engineering Inc. BOCCO
BOCCO is a communication robot provided by YUKAI Engineering Inc.

SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-05-18 11:19:00 +02:00
Michal Cieslakiewicz
45dc530334 ar71xx: WNDR3700: enable RFKILL function for Wifi button
Wifi button for WNDR3700 dual band routers has been renamed to "rfkill"
and its emitted keycode changed to KEY_RFKILL. This allows OpenWrt/LEDE
to support it 'out of the box' without additional tweaking.

Until this patch, button had been sending BTN_2 keycode which was
ignored by default (no action script present). To get expected behaviour
of switching radios on and off, user had to manually rename/link
'rfkill' script to name 'BTN_2' in /etc/rc.button directory.

This patch follows similar changes for other Netgear ar71xx routers,
for example WNR2000v3. It applies cleanly to both latest trunk and 17.01
branch. Tested on WNDR3700v1.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2018-05-18 11:18:53 +02:00
Christian Lamparter
707b6c815b brcm2708: add squashfs rootfs image
This patch adds a image with squashfs as the root filesystem.
A rootfs_data partition will be generated on the first boot
and placed inside the rootfs partition (just after the squashfs
image).

advantages:
 - it is possible to migrate from an existing -ext4
   installation and back via sysupgrade.
 - existing partition layout will not be lost.
 - slightly smaller image size.
 - support for attendedsysupgrade

disadvantages:
 - needs f2fs + tools as well. This is because fs-tools decides on the
   blocksize of the sdcard. So either f2fs or ext4 can get choosen as
   the rootfs_data filesystem (depends on the size of the root partition).
 - rootfs_data is placed into the rootfs partition. This makes
   it difficult for tools that expect a /dev/mmc0pX device.
   It also makes it difficult for data recovery tools since they
   might not expect to find a embedded partition or will be
   confused.

For people with existing build configurations: make sure to include mkf2fs
and f2fsck package into the image... Otherwise the new -squashfs image will
boot of a ram-overlay and won't keep the configurations after a reboot.

Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: Paul Spooren <spooren@informatik.uni-leipzig.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
2018-05-18 09:17:49 +02:00
Kristian Evensen
8f9baf5e1a x86: Add APU3 reference to x86 board.d
There is a new APU-model available, APU3. The device is configured in
the same way as the APU1 and APU2, so the same LED/network setup can be
used.

I considered changing the case to pc-engines-apu*, but I chose to follow
the existing pattern and add the full board name.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2018-05-18 09:17:24 +02:00
Christian Lamparter
16e39624b7 apm821xx: backport and reassign crypto4xx patches
This patch backports several patches that went upstream into
Herbert Xu's cryptodev-2.6 tree:

crypto: Use zeroing memory allocator instead of allocator/memset
crypto: crypto4xx - performance optimizations
crypto: crypto4xx - convert to skcipher
crypto: crypto4xx - avoid VLA use
crypto: crypto4xx - add aes-ctr support
crypto: crypto4xx - properly set IV after de- and encrypt
crypto: crypto4xx - extend aead fallback checks
crypto: crypto4xx - put temporary dst sg into request ctx

The older, outstanding patches from 120-wxyz series have been
upstreamed as well and therefore they have been reassigned to
fit into the series.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-05-18 09:14:09 +02:00
Christian Lamparter
e6e51ce87f apm821xx: don't select swconfig for the MR24
The swconfig package is part of the DEFAULT_PACKAGES list in
the apm821xx's nand subtarget. It's enabled by default because
the MX60(W) and WNDR4700 need it for their initramfs. However
the package is not necessary for the MR24's sysupgrade image, as
the MR24 does not have a switch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-05-18 09:13:19 +02:00
Roman Yeryomin
1f42deec8e ipq40xx: fix ethernet on ap-dk01.1
Not sure how it worked before but ethernet is disabled
by default in ipq4019 dtsi.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-18 09:12:53 +02:00
Koen Vandeputte
e2aa0c3f8b kernel: bump 4.14 to 4.14.41
Refreshed all patches

Dropped upstreamed patches:
522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch
523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch
525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch
527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch

updated patches:
524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch
030-USB-serial-option-fix-dwm-158-3g-modem-interface.patch

Added new ARM64 symbol: CONFIG_ARM64_ERRATUM_1024718

Compile-tested on: cns3xxx, imx6, mvebu (arm64), x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-18 09:10:46 +02:00
Koen Vandeputte
12f44b83a8 kernel: bump 4.9 to 4.9.100
Refreshed all patches

Added new ARM64 symbol: ARM64_ERRATUM_1024718

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-18 09:10:21 +02:00
Daniel Gonzalez Cabanelas
fbbb977772 brcm63xx: Tune the network configuration for several routers
- DGND3700v1: fix port numbers, they're in reverse order
- FaST2704n: there is no WAN port identified as such, only 4 LAN
- AD1018: configure the "FIBRE" port as WAN

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2018-05-18 08:55:37 +02:00
Rosen Penev
fec205f654 ramips: mmc: Sync with staging driver
Mostly whitespace cleanups. Some unneeded code was removed.

MMC init was also moved to the probe function as in
6069bdd

The cleanup commits are over 100, making it hard to do them individually.

Tested on GnuBee PC1 with an SD card being used as swap.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
v2: Fixed compile issue with mt7620
2018-05-18 08:49:52 +02:00
Matthias Schiffer
a5b77c9d9d
ath79: remove unused copy-file build step
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-17 22:11:56 +02:00
Matthias Schiffer
aea146736c
ath79: fix TP-Link TL-WR1043ND v1 image build
Both initramfs and flashed images are built and boot. No Ethernet, no WLAN,
probably further issues, so the image is not added to TARGET_DEVICES for
now.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-17 22:11:56 +02:00
Felix Fietkau
e9cb1b720d netfilter: fix hardware offload regression (FS#1551)
The relevant code needs to be enabled even if flow table support is only
compiled as module

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-17 08:21:54 +02:00
Mathias Kresin
75ed56a08a ath79: add AVM FRITZ!WLAN Repeater 300E
No known issues, everything works fine.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
bc04cf780e ath79: ar724x: fix pll settings
Add the syscon compatible, otherwise used functions like
syscon_regmap_lookup_by_phandle() will return an error and setting the
ethernet pll data wont work at all.

Fix the pll register width. Writing to registers out of the range via
syscon isn't possible and returns an error. On ar7242 the last pll
register - Current Audio Modulation Logic Output - is at 0x1805003c.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
f7ec385c13 ath79: add and enforce image metadata
Add metadata to images and make the metdata mandatory.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
f77db1a590 ath79: cleanup image build code
Remove recipes for not yet migrated boards. Drop variables which aren't
required due to the switch to devicetree like boardname.

Drop the legacy image build code. Boards added to this target shouldn't
use the legacy image build code anyway.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
cfe442c503 ath79: sysupgrade: drop unused variables
None of the variables are used at the moment.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
3e9d9f6225 ath79: sysupgrade: drop unused platform checks
None of these checks are used at the moment and most of them aren't
required if the image metadata validation is used.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
377197fdb3 ath79: sysupgrade: remove obsolete sysupgrade watchdog kill
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
0ff5785c5d ath79: fix dts files
Add the SoC compatible to the individual dts files. Rename the dts files
to match the common pattern.

Remove dts files wich aren't used and no image in ar71xx exists.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
8f7e28a783 ath79: enable wireless
PCI attached wireless works fine. So enable the wireless config symbols.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
bf781bd2ef ath79: cleanup kernel config
Remove outdated or not required kernel config settings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
b2cef5d045 ath79: drop platform data patches
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
a181781bf8 octeontx: make board.d files executable
Add the executable permission to the files to ensure they run on
firstboot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
d136192396 ath79: make board.d files executable
Add the executable permission to the files to ensure they run on
firstboot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
d8b475212b lantiq: kernel 4.14: use vbus-supply devicetree property
It isn't a phy supply, as the phy is still up if the GPIO is low. It
rather is the supply for the vbus. A correct setting/definition will be
relevant as soon as USB peripheral mode is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
0e9e8d8323 kernel: dwc2: add support for host mode external vbus supply
Backport patch adding support for the vbus-supply devicetree property,
which allows to specific GPIOs (via fixed regulators) to enable
vbus/usb power.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
0b62fe5ed8 lantiq: complete AVM FRITZ!Box 3370 support
Rename the image and use a compatible string which indicates that only
hardware revision 2 and higher is supported.

It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the
wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless
LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO.

The HWREV can be checked by connecting to the fritzbox right after power
on via ftp:

  ftp> quote GETENV HWSubRevision

Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash
chips are used. Usually it isn't a big deal but depending on the used
NAND flash chip, the ECC calculation is done different (and incompatible
of course).

Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND
chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND
flash chip are doing the ECC calculation in software.

Supporting both with a single DTS isn't possible. It might be possible
to add a patch selecting the ECC mode dynamicaly based on the found NAND
flash chip. But such a patch has no chance to get accepted upstream and
most likely need to be touched with every kernel update.

Instead two images are created. One for Micron NAND flash chip and one
for Hynix NAND flash chip. So far no pattern is known to identify the
used flash chip without opening the box.

Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as
input, which will cause a reboot 30sec after power on. For boards with
EVA version 2186 the installation is tricky as it has to be finished
within the 30sec time frame.

The EVA version can be checked by connecting to the fritzbox right after
power on via ftp:

  ftp> quote GETENV urlader-version

The ath9k eeprom/caldata is at a different and offset and stored in
reverse order (from the last byte to the beginning) on the flash.
Reverse the bits to bring the data into the format expected by the
ath9k driver.

Since the ath9k eeprom is stored in reverse order on flash, we can not
use the mac address from the on flash eeprom. Get the MAC address from
the tffs instead.

Within the same HW revision 5 of the Fritz!Box 3370 both version of the
vr9 SoC are used. During preparation of kernel 4.14 support, all
devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2
gphy firmware, which fixed the embedded phys for boards using the
version 1.2 of the vr9 SoC.

While at it, add a trigger to make use of the LAN LED. Setup the
build-in switch and add a hint for LuCI two show the ports in order
matching the labels on the case

Add support for the second USB port and provide the volatage GPIOs. Use
GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38.

Name the rootfs partition ubi and remove the mtd/rootfs related kernel
bootargs to use the OpenWrt autoprobing based on the partition name.

Enable sysupgrade support to allow an upgrade from a running system.
Since sysupgrade wasn't supported till now, drop image build code which
was added to allow a sysupgrade from earlier OpenWrt versions.

Build images that allow an (initial) installation via EVA bootloader.

To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote SETENV linux_fs_start 0
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1
  ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
d7b7483343 lantiq: switch to kernel 4.14
Use kernel 4.14 by default.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
John Crispin
7e15e21766 Revert "ramips: mmc: Sync with staging drivers"
This reverts commit 2d401925b9.

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-15 12:42:40 +02:00
Wei Yongjun
87c254c87e staging: mt7621-eth: fix return value check in mt7621_gsw_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: f079b6406348 ("staging: mt7621-eth: add gigabit switch driver (GSW)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:46:08 +02:00
Wei Yongjun
edec251870 staging: mt7621-eth: fix return value check in mtk_connect_phy_node()
In case of error, the function of_phy_connect() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.

Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:45:53 +02:00
Wei Yongjun
c4ae54dfab staging: mt7621-eth: fix return value check in mtk_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:45:34 +02:00
Rosen Penev
e07baec9fa ramips: pci: sync with staging driver
This is an amagalmation of two upstream commits dealing with whitespace
and dead code removal. I'm synching instead of having two separate commits
as they go out of order compared to previous commits here.

Tested on GnuBee PC1.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-15 06:45:07 +02:00
Rosen Penev
2d401925b9 ramips: mmc: Sync with staging drivers
Mostly whitespace cleanups. Some unneeded code was removed.

MMC init was also moved to the probe function as in
6069bdd087

The cleanup commits are over 100, making it hard to do them individually.

Tested on GnuBee PC1 with an SD card being used as swap.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-15 06:44:48 +02:00
Matthias Badaire
a0685deec4 ramips: Add i2c support for mt7620n
I2c is supported on mt7620n like on mt7620a when checking the datasheet

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-15 06:39:46 +02:00
Alberto Bursi
e09d4c850d kirkwood: support for buttons in Audi and Viper
Both these devices have a wps and a reset button on
GPIO pins, which need kmod-gpio-button-hotplug
package to work.

Add this package to their default package config.

Troubleshooted and tested on a Viper.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-05-15 06:39:37 +02:00
Johann Neuhauser
c15dfbeea0 ath79: fix gmac compatible in ar9330.dtsi and ag71xx_setup_gmac_933x
1. compatible property in node gmac was wrong

2. ag71xx_setup_gmac_933x should use np of gmac-config and
   not the pointer to gmac. gmac is only used for the reg address.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-05-15 06:38:07 +02:00
Michael Gray
bfbdeeb3de mvebu: add support for WRT32X (venom)
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.

Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-14 17:20:10 +02:00
Linus Walleij
1f56417e6b gemini: Augment DIR-685 device tree for RTL8366RB
This makes the ethernet and RTL8366RB come up on the
D-Link DIR-685.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-14 16:24:10 +02:00
Linus Walleij
3b48111df9 gemini: create zImage for DIR-685
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-14 16:24:09 +02:00
NeilBrown
edea934799 ramips: remove unnecessary resource details.
These resources are extracted from devicetree, so they aren't
needed here.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:24:07 +02:00
NeilBrown
1f78625714 ramips: remove conditional compilation.
Code currently defines:

and then compiles code only if they are defined.
We might want to disable some of these via devicetree one
day, but for now just remove the #defines and the
conditions - all the code for different ports is
easy to identify.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:24:04 +02:00
NeilBrown
5f7396ebef ramips: improve interrupt mapping
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.

The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:59 +02:00
Christian Lütke-Stetzkamp
2ad4daf579 ramips: Remove redundant owner assignment
Remove the owner assignment form the platform driver as
platform_driver_register() already initializes the owner.
Found using coccinelle.

Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:36 +02:00
Rosen Penev
a098a78a33 ramips: Move PCI driver to files directory
This will make it easier to port upstream code.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-14 15:55:17 +02:00
Jo-Philipp Wich
aadca035bc at91: sama5d4: fix bad mkubifs options
Drop the "-x lzo" compression type override from MKUBIFS_OPTS since we
do not support it in mkfs.ubifs. Attempting to use LZO compression results
in "Error: bad compressor name".

The build system also appends an explicit "--compr=zlib" to the mkfs command
line, turning the "-x" flag into a no-op anyway.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-13 18:33:47 +02:00
Rafał Miłecki
404508001e kernel: use accepted version of bcm47xxpart fix commit
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 23:53:44 +02:00
Rafał Miłecki
070693477a kernel: backport mtd patch for minor partitioning cleanup
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 23:14:07 +02:00
Felix Fietkau
a3096b4b33 kernel: fix build error in flow offload code with CONFIG_NETFILTER=n
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-12 22:28:00 +02:00
Rafał Miłecki
02225f5763 bcm53xx: backport the first bunch of 4.18 BCM5301X patches
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 15:38:55 +02:00
Jo-Philipp Wich
cf7a88cf5a at91: cleanup kernel configurations
The subtarget configurations contained a lot of reduntant symbols, arbitrary
overrides and symbols set to =m.

Remove most of these redundant settings to shrink the subtarget configurations
to a manageable size.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 18:24:00 +02:00
Jo-Philipp Wich
f23326eb76 at91: sama5d2: remove CONFIG_XZ_DEC override
Fixes the following error spotted by the buildbot:

    Package kmod-fs-squashfs is missing dependencies for the following libraries:
    xz_dec.ko

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 16:40:34 +02:00
Jo-Philipp Wich
0167f53b9d at91: add missing config symbols
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 16:01:26 +02:00
Jo-Philipp Wich
d8c7cd9cb1 kernel: rtl8366_smi: guard of_mdiobus_register() call
Make the call to of_mdiobus_register() dependant on CONFIG_OF to avoid
pulling in an unwanted dependency on of_mdio.ko.

Fixes: 3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 15:07:56 +02:00
Piotr Dymacz
ce4d2fb5cc ar71xx: fix and improve ALFA Network Tube2H support
Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).

Fixes: FS#1532

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-05-09 20:32:47 +02:00
Matthias Schiffer
db34cdf6c5
ath79: Ubiquiti Airmax M: add relocate-kernel to invalidate cache
Apply ar71xx fix for broken Ubiquiti bootloader to ath79 as well.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-08 21:14:24 +02:00
Felix Fietkau
6069bdd087 ramips: move mtk-mmc init to probe function to avoid breaking NAND flash
The driver messes with the pin control settings - MMC and NAND are
mutually exclusive

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-08 17:56:04 +02:00
Felix Fietkau
f95a4aa565 ramips: clean up the mt7621 nand flash driver hacks, add support for the xiaomi mir3g flash chip
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-08 17:56:04 +02:00
Rafał Miłecki
97f3c0f041 brcm47xx: switch to the kernel 4.14
The biggest (and the only?) disadventage of this is obviously an
increased image size.

For mips74k the size of vmlinux goes up from 4186684 B to 4701436 B.
Most devices use LZMA compressed kernel so probably more important is
vmlinux.lzma size which goes up from 1342945 B to the 1508498 B.

Still this isn't something that should stop target kernel bump. There
are various adventages of kernel 4.14. If kernel / image size is a
serious concern for anyone, it's perfectly possible to use previous
release which is pretty solid for the brcm47xx.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Paul Wassi <p.wassi@gmx.at>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
2018-05-08 09:55:10 +02:00
Rafał Miłecki
f9dcdc7fef kernel: mark source kernel for netfilter backports
This helps keeping track on patches & adding new kernels in the future.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-08 09:42:07 +02:00
Davide Ammirata
004cc22e4e ramips: add support for mqmaker witi 512mb version
Splitted out the dts file and create the new dts for the 256 MByte RAM and
the 512 MB RAM version.

Migrate both versions to the common board detection.

The install the 512 MByte Version on a board running the 256 MByte image,
a forceful sysupgrade with the -F flag is required.

Signed-off-by: Davide Ammirata <list@davidea.it>
2018-05-07 18:54:23 +02:00
Matthias Badaire
5ef79af4f8 ramips: add support for Ravpower WD03
The RavPower WD03 is a battery powered SD card reader and a USB port.

Specifications:
SOC:     MediaTek MT7620N
BATTERY: 6000mah
WLAN:    802.11bgn
LAN:     1x 10/100 Mbps Ethernet
USB:     1x USB 2.0 (Type-A)
RAM:     PM Tech PMD708416CTR-5CN 32 MB
FLASH:   Holtek HT66F40 - 8 MB Flash
LED:     Power button and 4 leds to indicate power level of the
         battery (could not get control of that)
INPUT:   Power, reset button
OTHER:   USB SD-Card reader with card detect on GPIO#42

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - installation from tftp
 - OpenWRT sysupgrade (Preserving and non-preserving)
 - LEDs
 - Buttons

Installation:
 - Download the sysupgrade image
 - Place it in the root of a clean TFTP server running on your computer.
 - Rename the image to "kernel" — be sure there is no file extension.
 - Plug the WD03 into your computer via ethernet.
 - Set your computer to use 10.10.10.254 as its IP address.
 - With your WD03 shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The WD03 (10.10.10.128) will look for your computer at 10.10.10.254
   and install the kernel file. Once it has finished installation of the
   kernel file, it will search for a (nonexistent) rootfs file — when it
   begins searching for this file, shut down the WD03 by holding the
   power button normally.
 - Start up your WD03 normally.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-07 18:54:23 +02:00
Mathias Kresin
ef19747b6c lantiq: kernel 4.14: Remove reboot/remove reset asserts
Backport patch accepted upstream which removes the reset asserts of the
xrx200 gphy driver on reboot/remove.

While doing a global software reset, these bits are not cleared and let
some bootloader fail to initialise the GPHYs. The bootloader don't expect
these bits to be set, as they aren't during power on.

The asserts were a workaround for a wrong syscon-reboot mask. With a mask
set which includes the GPHY resets of the first reset register, the
resets of the second reset register arn't required any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 18:53:08 +02:00
John Crispin
99f10b193e ath79: drop dts/Makefile
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 15:01:12 +02:00
Russell Senior
4aacd6388a ath79: u-boot partitions should be read-only in dts
Some of the new ath79 device trees were missing read-only tags on the
u-boot partitions.  This adds the tags where previously missing.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-05-07 13:07:00 +02:00
Rafał Miłecki
4edd4cb2b3 ath79: use the new DT fixed partitions syntax
This new syntax is slightly better designed & uses "compatible" string.
For details see Documentation/devicetree/bindings/mtd/partition.txt .

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-07 12:57:47 +02:00
John Crispin
7fe77a5962 ath79: revert license change on upstream DTS files
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 12:52:03 +02:00
David Bauer
b6a4c67468 ar71xx: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.

SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM:   Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
USB:   1x USB 2.0
IN:    WPS button, WiFi button
OUT:   Power LED green, Internet LED green, WLAN LED green,
       LAN LED green, INFO LED green, INFO LED red
UART:  Header Next to Black metal shield
       Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
       The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (LAN + WAN)
 - WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Not working:
 - USB port

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-07 10:42:26 +02:00
Rafał Miłecki
66c8afd115 ath79: relicense DTS files to the GPL 2.0+ / MIT
Some maintainers prefer DTS files licensed under permissive license like
MIT / BSD. As all DT bindings should be OS independent and DTS files are
pretty separated from Linux code it probably makes sense to share them
across projects.

The safest solution is to use dual licensing: that way it stays clear
these files can be used in GPL projects without depending on current
belief of licenses compatibility.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin <john@phrozen.org>
2018-05-07 10:31:35 +02:00
John Crispin
53c474abbd ath79: add new OF only target for QCA MIPS silicon
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 08:06:51 +02:00
John Crispin
3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 08:06:51 +02:00
Rafał Miłecki
ed00387dc5 bcm53xx: switch to the new/alternative SPI controller driver
This switches bcm53xx from spi-bcm53xx to the spi-bcm-qspi driver. The
later one was developed by Broadcom and is more advanced one. It
supports more modes, setting a speed, setting bits per word and uses
IRQs instead of polling.

This increases kernel size from 1808120 B to the 1811160 B (by 3040 B).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-07 07:56:38 +02:00
John Crispin
6e0ae87a98 ramips: disable spi full duplex on mt7621
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-05 08:25:18 +02:00
Linus Walleij
6cd2e1f947 gemini: Add ethernet to DNS-313 and Wiliboard
This adds an interrim patch for v4.14 based on an
upstream commit to get ethernet working on D-Link DNS-313
(probably also on the Wiliboards)

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
ce93b05bf1 gemini: fix hard disk boot on D-Link devices
Since the D-Link devices boot from hard disk we need to
add the following changes to Gemini:

- Supply a bootarg in the device tree so we can boot from
  the right partition (/dev/sda4 on DNS-313)
- Disable forced command line in config so the kernel picks
  up the right bootargs from the device tree
- Enable EXT4 in the config as this is used for rootfs else
  we get nowhere, we cannot load this as a module because,
  well, it is supposed to be loaded from the root partition
  (chicken and egg problem).
- Enable jbd2 and mbcache (needed by ext4)

Also clean out the premature attempts to dynamically
modify the command line in the Image makefile: we should
pass this with the device tree bootargs instead, it works
much better.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
2c35bcffd0 gemini: add rtl8366rb to dir-685 board
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
af069fbd24 gemini: cleanup kernel config
Disable video and input drivers - they are needed only for one
board and can be enabled via modules if/when UI will be available.
Use LED drivers from packages.
Cleanup other things unnecessarily overriding defaults.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
91930c0f99 gemini: remove 4.4 support
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
6409b159e8 gemini: switch to 4.14
This introduces Device/ infrastructure and images
for all boards available upstream.

Changes from Linus submitted version:
- fix Raidsonic image generation
- remove redundant (old) image generation
- remove redundant header tool for dns313 board

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
4f74957584 gemini: add 4.14 support
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.

Tested on Raidsonic NAS4220B and D-link DNS-313.

ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed

ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
  of the v4.4 patches to separate (big) patches.

ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
  dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
  file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
  1 minute by default, if we have the hdparm tool installed

ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
55c9aa27be gemini: rename files directory (preparation for 4.14)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Sandeep Sheriker Mallikarjun
610770dc5b at91: refreshing kernel configurations.
refreshing kernel configurations for sama5 and legacy subtarget.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
27ca6cdc7b at91: Add SAMA5D2 PTC EK board
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
60750ab505 at91: reorganize at91 subtargets
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
  1. able to set neon flags to sama5d2 & sama5d4 subtargets.
  2. fix the make clean which removes all the subtargets in bin folder.
  3. able to configure kernel specific to subtarget.
  4. able to set vfpu4 flags to samad3 subtargets.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
581f5e2392 at91: sdcard image with ext4 rootfs
creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:21 +02:00
Sandeep Sheriker Mallikarjun
22c398d257 at91: Add SAMA5D27 SOM1 EK board
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:21 +02:00
Sandeep Sheriker Mallikarjun
130224cc47 at91: fix sdcard create image
copying at91bootstrap and uboot binaries to sdcard image is done
based on device name instead of dts name and this avoids creating
multiple u-boot and at91bootstrap binaries.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:01 +02:00
Felix Fietkau
58f7b5b96c kernel: add missing in6_dev_put_clear call to an ipv6 network patch
Fixes "unregister_netdevice: waiting for lo to become free. Usage count = 1" messages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-02 15:32:07 +02:00
Rosen Penev
45219c1c0f kernel: Restrict dmesg output to root.
In typical OpenWrt setups, there are no other users that have a shell spawned for them by default.

This can be overriden by the kernel.dmesg_output syssctl.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-04-30 09:01:33 +02:00
Sandeep Sheriker Mallikarjun
2391d6a29e at91: sama5: remove neon and VFPv4 support
sama5d2 & samad4 have neon feature and sama5d3 does not have neon
feature due to which sama5d3 boot fails with error message Kernel
panic - not syncing: Attempted to kill init! exitcode=0x00000004.
removing neon & VFPv4 support to fix this

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-04-30 09:01:12 +02:00
Sandeep Sheriker Mallikarjun
80fe9bd71c at91: fix build error for wb50n.
when external kernel is selected from menuconfig, device wb50n is not
avaliable and build fails. As a fix adding checks for external kernel.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-04-30 09:01:12 +02:00
Simon Paterson
264feab1e7 ar71xx: Add userspace support for Mikrotik rb-2011iLS
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.

https://mikrotik.com/product/RB2011iLS-IN

Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
2018-04-30 09:01:12 +02:00
Koen Vandeputte
3435dbdc1c kernel: bump 4.14 to 4.14.37
Refreshed all patches

Compile-tested on: cns3xxx, imx6, octeon, ramips/mt7621, x86/64
Runtime-tested on: cns3xxx, imx6, octeon, ramips/mt7621, x86/64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[add extra tested targets to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-04-30 09:07:53 +03:00
Mathias Kresin
3877550114 arm64: enable harden branch predictor
Enable the harden branch predictor for arm64 as it is recommend.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-27 21:34:18 +02:00
Mathias Kresin
25f47c7bf9 kernel: add missing config symbols
The harden branch predictor was backported for arm64 with 4.9.92-96.

Fixes: 9aa196e0f2 ("kernel: bump 4.9 to bump 4.9.96")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-27 21:34:00 +02:00
Felix Fietkau
67aec988c4 brcm47xx: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Felix Fietkau
771f1ca3ff brcm63xx: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Felix Fietkau
1de74df8b9 bcm53xx: drop linux 4.4 and 4.9 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Christo Nedev
50b0919628 brcm2708: Add support for raspberry pi 3 b+.
Signed-off-by: Christo Nedev <christo.nedev@me.com>
2018-04-27 09:59:33 +02:00
Rosen Penev
7912677086 kernel: Fix data corruption on some mips devices.
This is mainly a bug fix for multi-core MIPS systems where L1 caches besides the primary do not get flushed.

The most obvious problem is data corruption on SATA and USB devices where read requests are typically larger than the cacheline size.

This may also fix ar71xx systems that suffer from similar data corruption but I have not tested if it does.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-04-27 09:59:33 +02:00
Matthias Schiffer
d168c2cf81
ar71xx: Ubiquiti Airmax M: add relocate-kernel to invalidate cache
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.

As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-26 20:40:07 +02:00
Koen Vandeputte
6cd41b419c kernel: bump 4.14 to 4.14.36
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Fixes for CVEs:
CVE-2018-1108
CVE-2018-1092
CVE-2018-1094
CVE-2018-1095

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
2018-04-26 08:54:01 +02:00
Kevin Darbyshire-Bryant
9aa196e0f2 kernel: bump 4.9 to 4.9.96
Refresh patches, following required reworking:

ar71xx/patches-4.9/930-chipidea-pullup.patch
layerscape/patches-4.9/302-dts-support-layercape.patch
sunxi/patches-4.9/0052-stmmac-form-4-12.patch

Fixes for CVEs:
CVE-2018-1108
CVE-2018-1092

Tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Arjen de Korte <build+openwrt@de-korte.org>
2018-04-26 08:53:54 +02:00
Damir Samardzic
6f4faf833d mvebu: cortexa72: enable Marvell 10G PHY by default
This one enables 10 GbE ports on MACCHIATObin.

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-04-25 20:37:22 +02:00
Mathias Kresin
91e11bec74 ramips: fix mt7628 eval board pinmux
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.

Fixes: FS#1515

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-25 20:33:27 +02:00
Mathias Kresin
d089a5d773 ramips: create image for mt7628 evb board
The image for the EVB board got lost with the merge of the mt7628 and
mt7688 subtargets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-23 22:07:22 +02:00
Tobias Wolf
3d800f14a9 ramips: use patch-dtb for F5D8235 V1
The old DTB method (OWRTDTB) is not recognized by the boot process
anymore with 4.9/4.14.

This patch reuses KERNEL_DTB to get a valid DTB applied to the kernel
image.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2018-04-23 22:07:22 +02:00
Giuseppe Lippolis
78666c7ba0 kernel: fix usb interface on 3G dwm-158 modem
The current option driver binds to the usb interface 2,3,4,5.
But the interface 4 and 5 doesn't answer to the AT commands.
On the new openwrt configuration the wwan script select the 5th
interface as control interface, failing to establish the
3G connection.

Backport the fix for the problem.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
c6aac196b8 ipq40xx: fix gpio-hog related boot issues
The pinctrl initialization fails with the MSM pinctrl code and gpio-hogs
because either the gpio ranges are not yet initialized (missing gpio-range
in DT) or that the msm driver unconditionally tries to re-initializes the
ranges (gpio-range in DT).

To allow gpio-hogs and similar early-boot gpio code, the gpio-ranges must
be in the device tree and the pinctrl-msm code must check whether the range
was already initialized by the DT.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[drop changes to unrelated dtsi files, refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
856f0d5d0d ipq40xx: use upstream board-2.bin
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00