ramips: add support for ZyXEL Keenetic Extra II
Specification: - System-On-Chip: MT7628N/N - CPU/Speed: 580 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 5x 10/100 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (57600 8n1) - Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn - Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac - USB: Yes 1 x 2.0 - 4x LED, 3x button The device supports dual boot mode. So we use only first half of flash. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin" to "kextra2_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
This commit is contained in:
parent
9e2c28472c
commit
7d07bc96b7
6 changed files with 228 additions and 2 deletions
|
@ -555,6 +555,11 @@ zorlik,zl5900v2)
|
|||
zte-q7)
|
||||
set_wifi_led "$boardname:blue:status"
|
||||
;;
|
||||
zyxel,keenetic-extra-ii)
|
||||
set_wifi_led "$boardname:green:wifi"
|
||||
set_usb_led "$boardname:green:usb"
|
||||
ucidef_set_led_switch "internet" "internet" "$boardname:green:internet" "switch0" "0x01"
|
||||
;;
|
||||
youku-yk1)
|
||||
set_wifi_led "$boardname:blue:air"
|
||||
set_usb_led "$boardname:blue:usb"
|
||||
|
|
|
@ -218,7 +218,8 @@ ramips_setup_interfaces()
|
|||
wrtnode2p | \
|
||||
wrtnode2r | \
|
||||
youhua,wr1200js|\
|
||||
zbt-wa05)
|
||||
zbt-wa05|\
|
||||
zyxel,keenetic-extra-ii)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
|
||||
;;
|
||||
|
|
|
@ -54,7 +54,8 @@ get_status_led() {
|
|||
x5|\
|
||||
x8|\
|
||||
xdxrn502j|\
|
||||
wn3000rpv3)
|
||||
wn3000rpv3|\
|
||||
zyxel,keenetic-extra-ii)
|
||||
status_led="$boardname:green:power"
|
||||
;;
|
||||
3g-6200nl)
|
||||
|
|
|
@ -226,6 +226,7 @@ platform_check_image() {
|
|||
zbt-wr8305rt|\
|
||||
zorlik,zl5900v2|\
|
||||
zte-q7|\
|
||||
zyxel,keenetic-extra-ii|\
|
||||
youku-yk1)
|
||||
[ "$magic" != "27051956" ] && {
|
||||
echo "Invalid image type."
|
||||
|
|
206
target/linux/ramips/dts/ki_rb.dts
Normal file
206
target/linux/ramips/dts/ki_rb.dts
Normal file
|
@ -0,0 +1,206 @@
|
|||
/dts-v1/;
|
||||
|
||||
#include "mt7628an.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "zyxel,keenetic-extra-ii", "mediatek,mt7628an-soc";
|
||||
model = "ZyXEL Keenetic Extra II";
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x8000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,57600n8";
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
poll-interval = <20>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
fn {
|
||||
label = "fn";
|
||||
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power {
|
||||
label = "keenetic-extra-ii:green:power";
|
||||
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
internet {
|
||||
label = "keenetic-extra-ii:green:internet";
|
||||
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi {
|
||||
label = "keenetic-extra-ii:green:wifi";
|
||||
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "keenetic-extra-ii:green:usb";
|
||||
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
usbpower {
|
||||
gpio-export,name = "usbpower";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
m25p80@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
m25p,chunked-io = <32>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-config";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@40000 {
|
||||
label = "rf-eeprom";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "firmware";
|
||||
reg = <0x50000 0xe90000>;
|
||||
};
|
||||
|
||||
partition@ee0000 {
|
||||
label = "config_1";
|
||||
reg = <0xee0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ef0000 {
|
||||
label = "storage";
|
||||
reg = <0xef0000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "dump";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "u-state";
|
||||
reg = <0x1000000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1030000 {
|
||||
label = "u-config_res";
|
||||
reg = <0x1030000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1040000 {
|
||||
label = "rf-eeprom_res";
|
||||
reg = <0x1040000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1050000 {
|
||||
label = "firmware_2";
|
||||
reg = <0x1050000 0xe90000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1ee0000 {
|
||||
label = "config_2";
|
||||
reg = <0x1ee0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ðernet {
|
||||
mtd-mac-address = <&factory 0x4>;
|
||||
mediatek,portmap = "wllll";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
pcie-bridge {
|
||||
mt76@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
device_type = "pci";
|
||||
mediatek,mtd-eeprom = <&factory 0x8000>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
mtd-mac-address = <&factory 0x8004>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "gpio", "i2s", "refclk", "spi cs1", "uart1", "wled_an";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
|
@ -313,3 +313,15 @@ define Device/zbtlink_zbt-we1226
|
|||
DEVICE_TITLE := ZBTlink ZBT-WE1226
|
||||
endef
|
||||
TARGET_DEVICES += zbtlink_zbt-we1226
|
||||
|
||||
define Device/zyxel_keenetic-extra-ii
|
||||
DTS := ki_rb
|
||||
IMAGE_SIZE := 14912k
|
||||
BLOCKSIZE := 64k
|
||||
DEVICE_TITLE := ZyXEL Keenetic Extra II
|
||||
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pad-to $$$$(BLOCKSIZE) | \
|
||||
check-size $$$$(IMAGE_SIZE) | zyimage -d 6162 -v "ZyXEL Keenetic Extra II"
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_keenetic-extra-ii
|
||||
|
|
Loading…
Reference in a new issue