ath79: add support for TP-Link RE450 v2
TP-Link RE450 v2 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button - UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers) Flash instruction: Apply factory image in OEM firmware web-gui. U-Boot does not seem to have any recovery functions, so debricking requires connection via UART. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
This commit is contained in:
Peter Lundkvist
John Crispin
parent
f4ac88b509
commit
781ad46206
7 changed files with 263 additions and 1 deletions
|
|
@ -28,6 +28,10 @@ case "$board" in
|
|||
ucidef_set_led_switch "lan1" "LAN1" "netgear:green:lan1" "switch0" "0x02" "0x0f"
|
||||
ucidef_set_led_switch "lan2" "LAN2" "netgear:green:lan2" "switch0" "0x04" "0x0f"
|
||||
;;
|
||||
"tplink,re450-v2")
|
||||
ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
|
||||
ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"
|
||||
;;
|
||||
"tplink,tl-mr3020-v1")
|
||||
ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x02"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -13,6 +13,7 @@ ath79_setup_interfaces()
|
|||
ucidef_set_interface_lan "eth0" "dhcp"
|
||||
;;
|
||||
"avm,fritz300e"|\
|
||||
"tplink,re450-v2"|\
|
||||
"tplink,tl-mr10u"|\
|
||||
"tplink,tl-wr703n"|\
|
||||
"ubnt,unifiac-lite"|\
|
||||
|
|
|
|||
|
|
@ -91,6 +91,10 @@ case "$FIRMWARE" in
|
|||
ath10kcal_extract "ART" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
||||
;;
|
||||
"tplink,re450-v2")
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
||||
;;
|
||||
"tplink,tl-archer-c7-v2")
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)
|
||||
|
|
|
|||
195
target/linux/ath79/dts/qca9563_tl-re450-v2.dts
Normal file
195
target/linux/ath79/dts/qca9563_tl-re450-v2.dts
Normal file
|
|
@ -0,0 +1,195 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,re450-v2", "qca,qca9563";
|
||||
model = "TP-Link RE450 v2";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-status = &system;
|
||||
mdio-gpio0 = &mdio2;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system: power {
|
||||
label = "tp-link:blue:power";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "tp-link:blue:wlan2g";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "tp-link:blue:wlan5g";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
lan_link {
|
||||
label = "tp-link:green:lan_link";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
lan_data {
|
||||
label = "tp-link:green:lan_data";
|
||||
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
wps_blue {
|
||||
label = "tp-link:blue:wps";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
wps_red {
|
||||
label = "tp-link:red:wps";
|
||||
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
power {
|
||||
label = "Power button";
|
||||
linux,code = <KEY_POWER>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
leds {
|
||||
label = "LED control button";
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "WPS button";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio2: mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>, /* MDC */
|
||||
<&gpio 4 GPIO_ACTIVE_HIGH>; /* MDIO */
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
phy0: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
device_type = "ethernet-phy";
|
||||
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "firmware";
|
||||
reg = <0x020000 0x5e0000>;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "partition-table";
|
||||
reg = <0x600000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
info: partition@610000 {
|
||||
label = "product-info";
|
||||
reg = <0x610000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@630000 {
|
||||
label = "config";
|
||||
reg = <0x630000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
mtd-mac-address = <&info 0x8>;
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&info 0x8>;
|
||||
};
|
||||
|
|
@ -1,4 +1,4 @@
|
|||
DEVICE_VARS += TPLINK_HWID TPLINK_HWREV TPLINK_FLASHLAYOUT TPLINK_HEADER_VERSION TPLINK_BOARD_NAME
|
||||
DEVICE_VARS += TPLINK_HWID TPLINK_HWREV TPLINK_FLASHLAYOUT TPLINK_HEADER_VERSION TPLINK_BOARD_NAME TPLINK_BOARD_ID
|
||||
|
||||
define rootfs_align
|
||||
$(patsubst %-256k,0x40000,$(patsubst %-128k,0x20000,$(patsubst %-64k,0x10000,$(patsubst squashfs%,0x4,$(patsubst root.%,%,$(1))))))
|
||||
|
|
|
|||
|
|
@ -13,6 +13,24 @@ define Device/tl-archer-c7-v2
|
|||
endef
|
||||
TARGET_DEVICES += tl-archer-c7-v2
|
||||
|
||||
define Device/tl-re450-v2
|
||||
$(Device/tplink)
|
||||
ATH_SOC := qca9563
|
||||
IMAGE_SIZE := 6016k
|
||||
DEVICE_TITLE := TP-LINK RE450 v2
|
||||
DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
|
||||
TPLINK_HWID := 0x0
|
||||
TPLINK_HWREV := 0
|
||||
TPLINK_BOARD_ID := RE450-V2
|
||||
LOADER_TYPE := elf
|
||||
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header -O
|
||||
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \
|
||||
append-metadata | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
|
||||
SUPPORTED_DEVICES := tplink,re450-v2
|
||||
endef
|
||||
TARGET_DEVICES += tl-re450-v2
|
||||
|
||||
define Device/tl-wdr3600
|
||||
$(Device/tplink-8mlzma)
|
||||
ATH_SOC := ar9344
|
||||
|
|
|
|||
|
|
@ -1079,6 +1079,46 @@ static struct device_info boards[] = {
|
|||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the RE450 v2 */
|
||||
{
|
||||
.id = "RE450-V2",
|
||||
.vendor = "",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:00000000}\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:55530000}\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:45550000}\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:4A500000}\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:43410000}\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:41550000}\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:41530000}\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:4B520000}\r\n"
|
||||
"{product_name:RE450,product_ver:2.0.0,special_id:42520000}\r\n",
|
||||
.support_trail = '\x00',
|
||||
.soft_ver = NULL,
|
||||
|
||||
/* We're using a dynamic kernel/rootfs split here */
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"firmware", 0x20000, 0x5e0000},
|
||||
{"partition-table", 0x600000, 0x02000},
|
||||
{"default-mac", 0x610000, 0x00020},
|
||||
{"pin", 0x610100, 0x00020},
|
||||
{"product-info", 0x611100, 0x01000},
|
||||
{"soft-version", 0x620000, 0x01000},
|
||||
{"support-list", 0x621000, 0x01000},
|
||||
{"profile", 0x622000, 0x08000},
|
||||
{"user-config", 0x630000, 0x10000},
|
||||
{"default-config", 0x640000, 0x10000},
|
||||
{"radio", 0x7f0000, 0x10000},
|
||||
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
{}
|
||||
};
|
||||
|
||||
|
|
|
|||
Loading…
Reference in a new issue