Commit graph

321 commits

Author SHA1 Message Date
Felix Fietkau
441ee62931 ar71xx: remove AP83 reference design board support
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Piotr Dymacz
c198ca682c ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00
Matthias Schiffer
a15ea362d7
ar71xx: fix syntax error in /lib/ar71xx.sh
Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.

Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-29 19:53:47 +01:00
Matthias Schiffer
9a5801e7f6
ar71xx: add model detection for UBNT Rocket Ti
Based-on-patch-by: Neal Oakey <neal.oakey@bingo-ev.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-29 15:37:39 +01:00
Piotr Dymacz
e33dcd1cfe ar71xx: add support for YunCore CPE830
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.

Use the same flash approach as for YunCore AP90Q.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
eb9ba2b91e ar71xx: add support for YunCore CPE870
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:

- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset

Vendor firmware access (login/password): Admin/5up

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
01dda0659e ar71xx: add support for YunCore AP90Q
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Flash instruction under vendor fimrware, using telnet/SSH:

1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
31952dbd1c ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530N
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.

All 3 devices are based on Qualcomm/Atheros QCA9531 v2.

COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
FUKAUMI Naoki
0165203304 ar71xx: add support for Buffalo BHR-4GRV2
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2016-11-16 10:54:33 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Christian Lamparter
098f7156cc ar71xx: add support for the Airtight C-60
This patch adds support for the Airtight C-60.

SOC:	Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM:	128 MiB
NOR:	MX25L3205D 4MiB
NAND:	ST Micro NAND 32MiB 3,3V 8-bit
SW-NET:	AR8327N (2 Ports)
WLAN1:	Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2:	Dual-Band AR9300 Rev:4 PCIe Chip

The switch is setup for an accesspoint:
	LAN1: (gigabit) is the wan-port.
	LAN2: (fast ethernet) is bridged with the br-lan.

Flashing Guide (via initramfs):
  1. Connect a PC to the serial port of the C-60.
     power up the C-60.

     Enter u-boot command prompt:
     #> nand erase
     #> setenv bootcmd "bootm 0x9f060000"
     #> saveenv
     #> setenv ipaddr 192.168.1.1
     #> setenv netmask 255.255.255.0
     #> setenv serverip 192.168.1.100
     #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
     #> tftpboot
     #> bootm

  2. Wait for the C-60 to boot LEDE.
     On the root prompt. Enter:
     # ubiformat /dev/mtd4
     # ubiattach -p /dev/mtd4

  3. After that copy the sysupgrade.tar onto the router and run:
     # sysupgrade sysupgrade.tar

     to flash the image.

Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-15 11:36:50 +02:00
Florian Beier
5abeba3450
ar71xx: add userspace support for D-Link DIR-869 A1, generate images
Signed-off-by: Florian Beier <beier.florian@gmail.com>
[Matthias Schiffer: fix factory image, improve commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:37 +02:00
Chris Blake
68d649f5cd ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker Gateway
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-09-27 17:50:22 +02:00
Neal Oakey
524d4110f9
ar71xx: add model detection for many Ubiquiti AirMax XM devices
Signed-off-by: Neal Oakey <neal.oakey@bingo-ev.de>
[Matthias Schiffer: minor adjustments]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-24 19:07:27 +02:00
Piotr Dymacz
f478fba663 ar71xx: add support for Zbtlink ZBT-WE1526
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)

Flash instruction:

Use sysupgrade in vendor firmare which is based on OpenWrt.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-08-18 09:49:18 +02:00
Chuanhong Guo
d1b20a3659 ar71xx: fix profile name of Mercury MW4530R
The mw4530r-v1 profile in tp-link.mk is for Mercury MW4530R.
There is no such a device called TL-WDR4530.
Also change MERCURY to Mercury in /lib/ar71xx.sh

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-08-15 15:18:35 +02:00
Matthias Schiffer
500a67a167
ar71xx: add revision detection for D-Link DIR-505 A1/A2
The A1 image also works on the A2, correctly set AR71XX_MODEL in this case.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-07-28 15:44:52 +02:00
John Crispin
96fa9aa13b ar71xx: add a missing ;; to ar71xx.sh
commit 42305ae24a ("ar71xx: add support for gl-mifi")

was missing a ;; breaking boot up

Signed-off-by: John Crispin <john@phrozen.org>
2016-07-24 11:17:34 +02:00
Zhao Gang
42305ae24a ar71xx: add support for gl-mifi
This add initial support for gl-mifi.
Product page: http://www.gl-inet.com/mifi/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-24 06:38:30 +02:00
Zhao Gang
d963ddf042 ar71xx: add support for gl-ar300m
This add initial support for gl-ar300m router.
Product page: http://www.gl-inet.com/ar300m/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-20 00:21:48 +02:00
Piotr Dymacz
d2c9b169b3 ar71xx: add support for jjPlus JWAP230
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers

Default configuration:

- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space

Flash instruction (do it under U-Boot, using RS232):

1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Piotr Dymacz
e767980eb8 ar71xx: add support for Wallys DR531
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers

Default configuration:

- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Allan Nick Pedrana
e61fe4e4d7 ar71xx: add support for OpenEmbed SOM9331
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.

Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
2016-06-07 11:21:55 +02:00
KeLei Liang
563e9d5e1b ar71xx: add WRTnode2Q support
Signed-off-by: KeLei Liang <xzmu@wrtnode.com>
2016-06-06 14:58:11 +02:00
Stijn Segers
d2a91f9853
ar71xx: Fix TL-WR841N v11 LEDs, use separate machine
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-05-31 17:36:51 +02:00
Alexander Couzens
c5ff273d85 ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510
Split profile into 2GHz and 5GHz. The 5GHz devices are
quite "special". The 2 GHz works perfect.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:49 +02:00
Sven Eckelmann
58dc285cd6 ar71xx: add user-space support for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
e10d12411c ar71xx: add user-space support for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Cezary Jackiewicz
0b45bec22c
ar71xx: add support for TP-LINK TL-WR842N/ND v3
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB

AP143 platform, similar to tl-wr841n v10/v11, but with USB

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-14 21:45:16 +02:00
P.Wassi
8307c2fe68 ar71xx: Add support for Ubiquiti UniFi AP AC PRO
Add support for the Ubiquiti UniFi AP AC PRO
Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
P.Wassi
c855e70491 ar71xx: Rename unifiac to unifiac-lite
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.

Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
blogic
75629fb2a8 ar71xx: add TP-Link TL-WR810N support
This patch adds support for the TP-Link TL-WR810N.
https://wiki.openwrt.org/toh/tp-link/tl-wr810n

Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com>

SVN-Revision: 49286
2016-05-10 10:43:12 +02:00
John Crispin
ee53a240ac ar71xx: Add support for the OMYlink OMY-G1
https://wiki.openwrt.org/toh/omylink/omy-g1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49258
2016-04-26 11:44:36 +00:00
John Crispin
5f1a82ec4f ar71xx: add TP-Link TL-WA901ND-v4 support
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 49158
2016-04-09 10:26:46 +00:00
John Crispin
d9799dea89 ar71xx: add support for Compex WPJ342
OpenWrt can be flashed with following uboot commands:

tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 49157
2016-04-09 10:26:41 +00:00
John Crispin
7461604bd9 ar71xx: add user-space support for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49150
2016-04-09 10:26:18 +00:00
John Crispin
2fa2d97ae2 ar71xx: add user-space support for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49142
2016-04-09 10:25:51 +00:00
John Crispin
3c91d5a479 ar71xx: fix the revision of a few TP-LINK devices in AR71XX_MODEL to match labels/image names
Let's not confuse users about the revisions of their devices when we can
easily avoid it.

Not tested on real hardware.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 49107
2016-04-01 07:12:00 +00:00
John Crispin
85c540b94e ar71xx: avoid AR71XX_MODEL ending with a space on some TP-LINK-like devices
Instead of adding the space when combining $model and $hwver, add the space
to the beginning of $hwver, so the resulting string won't end with a space
when $hwver is set to the empty string.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 49106
2016-04-01 07:11:56 +00:00
Luka Perkov
8258f8edb6 ar71xx: cosmetic fix of alfa ap120c/ap96 ordering
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49086
2016-03-24 21:09:34 +00:00
Luka Perkov
ebaba15331 ar71xx: add support for ap120c
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49082
2016-03-23 22:31:38 +00:00
John Crispin
3fd98db818 ar71xx: Add support for the OMYlink OMY-X1
This patch adds support for the OMYlink OMY-X1

https://wiki.openwrt.org/toh/omylink/omy-x1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49026
2016-03-16 09:26:58 +00:00
John Crispin
346b1905fb ar71xx: add support for the Telldus TellStick ZNet Lite
Signed-off-by: Micke Prag <micke.prag@telldus.se>

SVN-Revision: 48977
2016-03-10 19:07:26 +00:00
John Crispin
fbb2449953 AP121 target: fix board detection in ar71xx.sh
Signed-off-by: Attila Lendvai <attila@lendvai.name>

SVN-Revision: 48916
2016-03-04 08:33:38 +00:00