Commit graph

3190 commits

Author SHA1 Message Date
Tal Keren
0d9d980ecd firmware-utils: kernel image generator for TP-Link RE450
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:05 +01:00
Matthias Schiffer
324bdf3ecc
ar71xx: remove redundant -j from TL-WR1043ND v4 kernel build command
mktplinkfw ignores -j in combined mode, the EOF marker is added by
tplink-safeloader.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-21 23:29:00 +01:00
Ludwig Thomeczek
1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
Matthias Schiffer
0495181529
ar71xx: rename mktplinkfw-initramfs to more generic mktplinkfw-combined
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-20 14:38:48 +01:00
Kevin Darbyshire-Bryant
79abb8f140 kernel: bump to 4.4.39
Bump & refresh patches for all 4.4 targets.

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-12-20 09:35:36 +01:00
David Lutz
aada15af93
ar71xx: add support for TP-LINK TL-WR940N v4
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
2016-12-16 11:12:46 +01:00
Jo-Philipp Wich
98b14e0906 ar71xx: fix TL-WR842N v2 switch port order
The TL-WR842N v2 has the following switch port layout with swconfig port 0
being connected to eth1:

            Power  LAN4    LAN3    LAN2    LAN1    WAN     USB
             (*) | [...] | [...] | [...] | [...] | [...] | [.]
    swconfig port:   1       4       3       2      n/a
    netdev:        eth1    eth1    eth1    eth1    eth0

Adjust the board defaults to match this model specific layout.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-14 18:43:48 +01:00
Gad Krumholz
21cb84435a ar71xx: Added missing support for Linksys E2100L
It's based on the WRT160NL according to
https://wiki.openwrt.org/toh/linksys/e2100l

Based on research done here: https://forum.openwrt.org/viewtopic.php?id=24244
and here: https://forum.openwrt.org/viewtopic.php?pid=120791#p120791 this patch
was conceived.

Signed-off-by: Gad Krumholz <gad.krumholz@gmail.com>
[Jo-Philipp Wich: fix ordering, move addpattern change into separate commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-14 18:42:48 +01:00
Huan Truong
fd62fa752b ar71xx: Add support for Netgear WNR2000v1
This patch adds supports for the WNR2000v1 board with 4MB flash, and
produces device-specific factory, rootfs, and sysupgrade files for the
WNR2000v1. This board is errorneously claimed as supported on the OpenWRT
wiki as AP81, but AP81 image would not work because of APT81 image
requiring having 8MB of flash, while WNR2000v1 has only 4MB.

The image requires the u-boot bootloader to be modified to fuhry's
bootloader first.

Short specification:

- CPU: Atheros AR9132
- 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps
- 4 MB of Flash
- 32 MB of RAM
- UART header (J1) on board
- 1x button

Factory/Initial flash instructions:

- Set up a TFTP server on your local machine.
- Download the uImage for ar71xx-generic and the rootfs image for
  ar71xx-generic-wnr2000 and save in the tftp server root.
- Gain serial access to the router via the UART port (telnetenable over
  the network only won't work!).
- Upgrade the u-boot bootloader to fuhry's version by running the
  script: http://fuhry.com/b/wnr2000/install-repart.sh
- When the router restarts, interrupt u-boot and gain access to u-boot command line.
- Repartititon the board and flash initial uImage and rootfs as follow.

Commands to type in u-boot:

	# tells u-boot that we have a tftp server on 192.168.1.10
	setenv serverip 192.168.1.10

	# tells u-boot that the router should take the address 192.168.1.1
	setenv ipaddr 192.168.1.1

	# erase the region from 0x050000-0x3f0000
	erase 0xbf050000 +0x3A0000

	# loads sqfs.bin on TFTP server, and put it to memory address 0x81000000
	tftpboot 0x81000000 sqfs.bin
	# it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ
	# copy bit by bit 0xZZZZZZ bytes from offset 0x050000
	cp.b 0x81000000 0xbf050000 0xZZZZZZ

	# same to the uImage.bin, write it right next to sqfs.bin
	# again, 0xYYYYYY is the length that tftpboot reports
	tftpboot 0x81000000 uImage.bin
	cp.b 0x81000000 0xbf2a0000 0xYYYYYY

	# We need to tell the kernel what board it is booting into, and where to find the partitions
	setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd"

	# Tell u-boot where to find the uImage
	setenv bootcmd "bootm 0xbf2a0000"

	# Tell u-boot to save parameters to the u-boot-env partitions
	saveenv

	# Reset the board
	reset

Tested on:

- WNR2000v1 board.
- Initial flash works.

Known bugs:

- I don't know why factory image doesn't work on initial flash on stock
  firmware in u-boot recovery mode while it should.
- Sysupgrade does not yet work, if you do -f it will mess up your
  installation (requiring a reinstall of sqfs and uImage).

Signed-off-by: Huan Truong <htruong@tnhh.net>
2016-12-14 10:37:01 +01:00
Jing Lin
c9a9f9b8ce ar71xx: Add ath10k-firmware-qca988x for DomyWifi DW33D
The default package selection was missing the correct FW for ath10k to
work.

Signed-off-by: Jing Lin <mumuqz@163.com>
2016-12-14 10:37:01 +01:00
Kevin Darbyshire-Bryant
f5b833b8fe kernel: bump to 4.4.38
Bump & refresh patches for all 4.4 supported targets.

Compile & run tested: ar71xx - Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-12-13 08:28:28 +01:00
Matthias Schiffer
fcf54f79d2
ar71xx: simplify model detection for TP-Link Pharos devices
This also makes the detection more flexible, as it doesn't need to check
for each model explicitly.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-12 13:45:37 +01:00
Felix Fietkau
8f23ec609c ar71xx: remove obsolete flash chip locking code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:19 +01:00
Felix Fietkau
a5923cd549 ar71xx: remove PB92 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
30285facbe ar71xx: remove AP113 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
4c8a9b8e39 ar71xx: remove AP81 reference design board support
This board is very old and unlikely to still be relevant today.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
fd95dec2e3 ar71xx: remove obsolete duplicate driver source file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
441ee62931 ar71xx: remove AP83 reference design board support
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
fa04682f21 ar71xx: clean up spi controller related patches
Remove various hacks for fast read, un-break device tree support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:17 +01:00
Piotr Dymacz
c198ca682c ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00
Matthias Schiffer
9c5af2489a
ar71xx: fix LEDs and sysupgrade support for TL-WA801ND v3
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-06 19:08:35 +01:00
Felix Fietkau
2135e54c00 ar71xx: set GPIO reset line for Ubiquiti NanoStation Loco XW
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-04 11:41:50 +01:00
Felix Fietkau
106a4605c8 ar71xx: add support for configuring at803x PHY GPIO reset via platform data
Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW,
because ar71xx is not converted to device tree yet.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-04 11:41:50 +01:00
Matthias Schiffer
a15ea362d7
ar71xx: fix syntax error in /lib/ar71xx.sh
Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.

Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-29 19:53:47 +01:00
Matthias Schiffer
9a5801e7f6
ar71xx: add model detection for UBNT Rocket Ti
Based-on-patch-by: Neal Oakey <neal.oakey@bingo-ev.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-29 15:37:39 +01:00
Felix Fietkau
1cd7ff3e96 ar71xx: remove squashfs-64k rootfs image from bin directory, the generic one is enough
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 10:20:27 +01:00
Felix Fietkau
eff858e8df ar71xx: remove split kernel/rootfs images where the sysupgrade image can be written to flash directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 10:20:27 +01:00
Felix Fietkau
cc550d0005 ar71xx: remove 2MB flash variant of WP543
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:55:05 +01:00
Felix Fietkau
12e2beaaed ar71xx: remove legacy devices that cannot be supported due to kernel partition size limits
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:51:57 +01:00
Felix Fietkau
35dda35114 ar71xx: remove legacy gzip images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:44:39 +01:00
Felix Fietkau
88f6f0120d ar71xx: remove obsolete jffs2 image building code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-29 09:44:39 +01:00
Piotr Dymacz
6998b8a054 ar71xx: move DomyWifi DW33D to nand subtarget
This device uses NAND FLASH, so it should be kept in nand subtarget.

Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-24 22:37:40 +01:00
João Chaínho
39433bb618 ar71xx: Fix switch config on Mikrotik RB450/G
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2016-11-21 10:11:37 +01:00
Piotr Dymacz
e33dcd1cfe ar71xx: add support for YunCore CPE830
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.

Use the same flash approach as for YunCore AP90Q.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
eb9ba2b91e ar71xx: add support for YunCore CPE870
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:

- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset

Vendor firmware access (login/password): Admin/5up

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
01dda0659e ar71xx: add support for YunCore AP90Q
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Flash instruction under vendor fimrware, using telnet/SSH:

1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
31952dbd1c ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530N
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.

All 3 devices are based on Qualcomm/Atheros QCA9531 v2.

COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Paul Wassi
6e65576f2d ar71xx: fix drivers/mtd/nand/ar934x_nfc.c
Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw.
Add *page* in the argument list and remove the local variable.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-11-18 21:57:19 +01:00
João Chaínho
5dd13c071b ar71xx: enable serial console on mikrotik devices
This patch enables the serial console on some Mikrotik devices (RB450,
RB450G, RB493G, RB750UP).

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2016-11-18 09:41:14 +01:00
Stijn Tintel
8e47655d4e kernel: update kernel 4.4 to version 4.4.32
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-11-16 17:31:29 +01:00
Henryk Heisig
0d760bfba8 ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partition
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-16 11:01:18 +01:00
Jaylin Yu
7ee6ab1a31 ar71xx: Add usable, inactive LEDs on OpenMesh devices
OpenMesh devices have often LEDs which are not yet used by OpenWrt. These
should still be available as disabled LEDs in the system configuration for
easier modification.

Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com>
[sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh,
 add wifi/status LEDs]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-11-16 10:54:33 +01:00
FUKAUMI Naoki
0165203304 ar71xx: add support for Buffalo BHR-4GRV2
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2016-11-16 10:54:33 +01:00
Martin Weinelt
5247ac2f80
ar71xx, ramips: reduce CPU load and flickering on devices using rsslieds
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.

Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-16 01:42:15 +01:00
Matthias Schiffer
7ef0d7c4fc
ar71xx: enable HSR tuner on Ubiquiti UAP Outdoor+
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-15 18:54:07 +01:00
Matthias Schiffer
60983a486c
ar71xx: fix DEVICE_TITLE for Ubiquiti UAP Outdoor+
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-15 18:54:06 +01:00
Matthias Schiffer
9cac5e8be0
ar71xx: generate region-coded factory images for TP-Link TL-WR841ND v11
The latest stock firmwares for US and EU regions have started checking the
region code.

Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-11 03:29:59 +01:00
Felix Fietkau
462a7c0e96 ar71xx: fix kernel relocate stub parallel build issue
Use per-kernel directory

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-08 11:51:27 +01:00
Henryk Heisig
4ad68fa0a2 ar71xx: tl-wpa8630: Fix kernel lenght
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Chris Blake
53b43e65e7 ar71xx: Add net config for MR12 & MR16
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-31 12:52:56 +01:00
Christian Mehlis
7cb82d4b70 ar71xx: fix ethernet on wpj344 board
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
2016-10-31 12:52:56 +01:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
6b0d279ca5 ar71xx: build relocate stub for generic and legacy images
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
e19427bd79 ar71xx/base-files: rename 09_fix-trx-header 09_fix-checksum
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
136319e72d kernel: mtdsplit: add support for WRGG images
Support splitting WRGG images, found in some D-Link devices (e.g.
DAP-2695).

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Chuanhong Guo
c5a7e2c2fb ar71xx: Ignore firmware building errors of UBNT and CyberTAN devices
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-10-26 14:07:20 +02:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Chris Blake
fac018b25e ar71xx: Remove switch config for the MR12/MR16
These boards do not have a switch, so they should have never been added
to this file in the first place.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Chris Blake
28dd52b079 ar71xx: add mac partition to the MR12/MR16
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).

The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.

Once this partition is added to a device, you can set your MAC doing the
following:

mtd erase mac
echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5
sync && reboot

Where 00:18:0a:33:44:55 is your MAC address.

This was tested, and confirmed working on both the MR12 and MR16.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Chris Blake
d8662ac3c6 ar71xx: Move MR12 & MR16 from legacy to generic
This moves the Meraki MR12 and Meraki MR16 to the new generic target.
Tested and verified working on both devices.

Note that kernel/rootfs images are still generated. This is because they
are used for the inital flashing process due to the fun pace at which
UBoot erases/writes to SPI.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:44 +02:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Matthias Schiffer
83f7ec31f8
ar71xx: set EU region code for TP-Link TL-WA901ND v4
There is no US firmware for the TL-WA901ND v4 yet, so we'll just
unconditionally set the EU region for now.

This makes LEDE flashable on these devices again. The format of the region
string is slightly different from the one used on the Archer C7 that is
generated by mktplinkfw (the second half of the region string is missing),
but it's similar enough to make it work.

Tested-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-15 19:09:56 +02:00
Christian Lamparter
098f7156cc ar71xx: add support for the Airtight C-60
This patch adds support for the Airtight C-60.

SOC:	Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM:	128 MiB
NOR:	MX25L3205D 4MiB
NAND:	ST Micro NAND 32MiB 3,3V 8-bit
SW-NET:	AR8327N (2 Ports)
WLAN1:	Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2:	Dual-Band AR9300 Rev:4 PCIe Chip

The switch is setup for an accesspoint:
	LAN1: (gigabit) is the wan-port.
	LAN2: (fast ethernet) is bridged with the br-lan.

Flashing Guide (via initramfs):
  1. Connect a PC to the serial port of the C-60.
     power up the C-60.

     Enter u-boot command prompt:
     #> nand erase
     #> setenv bootcmd "bootm 0x9f060000"
     #> saveenv
     #> setenv ipaddr 192.168.1.1
     #> setenv netmask 255.255.255.0
     #> setenv serverip 192.168.1.100
     #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
     #> tftpboot
     #> bootm

  2. Wait for the C-60 to boot LEDE.
     On the root prompt. Enter:
     # ubiformat /dev/mtd4
     # ubiattach -p /dev/mtd4

  3. After that copy the sysupgrade.tar onto the router and run:
     # sysupgrade sysupgrade.tar

     to flash the image.

Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-15 11:36:50 +02:00
Karl Palsson
5d04dcedb4 ar71xx: move dragino2 from legacy to generic
Tested on real hardware with r1804.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2016-10-13 17:04:38 +02:00
Florian Beier
5abeba3450
ar71xx: add userspace support for D-Link DIR-869 A1, generate images
Signed-off-by: Florian Beier <beier.florian@gmail.com>
[Matthias Schiffer: fix factory image, improve commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:37 +02:00
Matthias Schiffer
594f0e80ce
ar71xx: add kernel support for D-Link DIR-869 A1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:36 +02:00
Matthias Schiffer
e407f1a4c8
ar71xx: add back SEAMA header checksum fix (as used on ramips)
The D-Link DIR-869 A1 doesn't accept images with the jffs2 marker added
after the checksummed range, so we need to include it in the checksum and
fix it on first boot.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:57:59 +02:00
Matthias Schiffer
212ce6bce1
ar71xx: avoid double lzma compression of kernel for SEAMA images
Use relocation loader instead of lzma loader.

Tested on D-Link DIR-869 A1.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:57:51 +02:00
Matthias Schiffer
0d1fb72241
ar71xx: add relocation loader
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:39:16 +02:00
Matthias Schiffer
fce0b5d893
ar71xx: clean up SEAMA image build code
Split seama-factory and seama-sysupgrade into smaller pieces (similar to
the ramips code) to make the image generation more flexible.

Also use standard pad-offset instead of adding a block of zeros at the
beginning of the image that is later cut off again. Standard pad-rootfs can
be used as the seal header doesn't contain an image size or checksum.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:32:24 +02:00
Amir Rachum
4c36bcc567
ar71xx: build image for Archer C7 v2 IL
TP-Link uses a different region coding mechanism for IL firmware for the Archer
C7 v2. Instead of of setting the region, they set a different TPLINK_HWREV.

Signed-off-by: Amir Rachum <amir@rachum.com>
2016-10-09 21:13:09 +02:00
Piotr Dymacz
52974da2bb ar71xx: update kernel config symbols
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:51 +02:00
Piotr Dymacz
c166b050fd ar71xx: base-files: fix boards order in lib/upgrade/platform.sh
Keep also case sections in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
8be47007a9 ar71xx: base-files: cleanups in lib/upgrade/platform.sh
This includes:

- code style fixes
- fix boards order within case sections

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
92870eac27 ar71xx: comsetic cleanups in files/arch/mips/ath79/{Makefile,machtypes.h}
Keep everything in alphabetical order and aligned in columns.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
6e58440fc1 ar71xx: base-files: cleanups in etc/board.d/01_leds
This includes:

- use of local 'board' variable in LED names, wherever possible
- merge of boards with exactly the same LED configuration

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
c142df3094 ar71xx: fix LED names for GL Innovations boards
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
8689078a9b ar71xx: base-files: fix code style in etc/board.d/01_leds
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
d09f4e0631 ar71xx: base-files: combine boards with the same config in etc/diag.sh
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
2917ae91ec ar71xx: base-files: cleanups in etc/diag.sh
This includes:

- code style fixes
- use of local 'board' variable in LED names, wherever possible

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
edcdb93467 ar71xx: base-files: fix boards order in etc/board.d/02_network
Keep everything in alphabetical order. Boards are ordered in two steps,
first within/inside common configuration (case section), then sections,
globally.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
a75cfac1f6 ar71xx: base-files: cleanups in etc/board.d/02_network
This includes:

- code style fixes
- removal of huge comment (it should be in doc, not here) and some small ones
- removal of redundant config for DR531/WPJ531 as the default is the same
- merge of boards with exactly the same interfaces config

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
4fa90c49c1 ar71xx: base-files: rework etc/board.d/02_network
Convert etc/board.d/02_network in ar71xx target to the same shape
as we have in ramips target. Split code into two new functions:

- interface/s setup in ar71xx_setup_interfaces()
- MAC/s setup in ar71xx_setup_macs()

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:48 +02:00
Álvaro Fernández Rojas
7d559169c5 kernel: update to v4.4.23
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-30 20:08:21 +02:00
Martin Blumenstingl
e7be0decf6 ar71xx: Do not use a hardcoded ath10k firmware mac address
ar71xx has an init-script for special devices where the ath10k OTP
calibration data is stored on the PCIe card's EEPROM (and thus can only
be read by ath10k). Unfortunately the OTP data uses the default mac
address (= all devices come with the same mac address, which leads to
problems when you have multiple of these devices in the same network).

To work around this the mac address is patched in the firmware during
the first boot of the device. To prevent flash wear this was only done
if the ath10k firmware matched a hardcoded md5sum.
However, if the md5sum does not match this can mean that either the mac
address was already patched (which is fine) - unfortunately it can also
mean that the firmware version was updated without updating the
hardcoded md5sum.

Change the "was the mac address already patched" check to actually
compare the mac address inside the ath10k firmware.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-09-28 08:39:01 +02:00
Chris Blake
68d649f5cd ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker Gateway
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-09-27 17:50:22 +02:00
Matthias Schiffer
9dbf8241c3
ar71xx: clean up DEVICE_PACKAGES of legacy devices
Remove arbitrary or redundant packages from DEVICE_PACKAGES.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-26 17:57:57 +02:00
Neal Oakey
524d4110f9
ar71xx: add model detection for many Ubiquiti AirMax XM devices
Signed-off-by: Neal Oakey <neal.oakey@bingo-ev.de>
[Matthias Schiffer: minor adjustments]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-24 19:07:27 +02:00
Jo-Philipp Wich
1c09849f6c treewide: remove bad local shell variable declarations
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-09-24 14:38:20 +02:00
Piotr Dymacz
dc9172b65b ar71xx: update kernel config symbols
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-09-19 15:30:32 +02:00
Piotr Dymacz
2ad0ecc101 ar71xx: mark U-Boot and radio calibration data partitions as read-only
General convention is to keep U-Boot and radio calibration
data (ART) mtd partitions marked as read-only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-09-19 15:30:32 +02:00
Matthias Schiffer
01e2024754
ar71xx: set region code of TP-Link TL-WDR3600/4300 to US
There are currently two stock firmwares for the TL-WDR3600/4300, a US and
a universal version. Both allow installing images with US region code, so
we don't need to provide multiple images.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-15 19:34:28 +02:00
Matthias Schiffer
b063faa2c8
ar71xx: separate TP-Link TL-WDR3600/4300/4310 profiles
Simplify modifying some of the images without affecting the others.

While we're at it, also unify the profiles to use := syntax and add "v1" to
the TL-WDR4300 name to make things more consistent.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-15 19:33:30 +02:00
Álvaro Fernández Rojas
d14c28fc80 kernel: update kernel 4.4 to version 4.4.20
Refresh patches for all targets that support kernel 4.4.
Compile-tested on brcm2708 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-15 08:10:55 +02:00
Mathias Kresin
61c2a7339a image: remove padding parameter from append-kernel/append-rootfs
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.

Furthermore the purpose of the extra parameter is hard to get without
reading the code.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-13 19:36:41 +02:00