KumiSystems/openwrtv4
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv4/target/linux/ar71xx/files/arch/mips/ath79
History
Piotr Dymacz 6165e4aab0 ar71xx: add support for TP-Link TL-WR902AC v1 
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

Root access over serial line in vendor firmware: root/sohoadmin.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
..
dev-ap9x-pci.c ar71xx: add correct named default wireless led by using platform leds 2017-04-08 14:30:00 +02:00
dev-ap9x-pci.h ar71xx: add correct named default wireless led by using platform leds 2017-04-08 14:30:00 +02:00
dev-dsa.c ar71xx: add v3.18 support 2015-02-15 19:45:29 +00:00
dev-dsa.h
dev-eth.c ar71xx: fix ethernet PLL configuration for QCA956x 2017-02-17 12:16:13 +01:00
dev-eth.h ar71xx: QCA956X: add missing register 2017-01-26 11:38:20 +01:00
dev-m25p80.c ar71xx: clean up spi controller related patches 2016-12-12 10:22:17 +01:00
dev-m25p80.h ar71xx: clean up spi controller related patches 2016-12-12 10:22:17 +01:00
dev-nfc.c
dev-nfc.h
Kconfig.openwrt ar71xx: add support for TP-Link TL-WR902AC v1 2017-07-04 08:58:54 +02:00
mach-a60.c ar71xx: add kernel support for the OpenMesh A40 board 2017-02-14 12:18:05 +01:00
mach-alfa-ap96.c ar71xx: clean up spi controller related patches 2016-12-12 10:22:17 +01:00
mach-alfa-ap120c.c ar71xx: cosmetic fix of alfa ap120c/ap96 ordering 2016-03-24 21:09:34 +00:00
mach-alfa-nx.c
mach-all0258n.c
mach-all0315n.c
mach-antminer-s1.c ar71xx: Bitmain Antminer S1/S3 set GPIO for USB Power 2015-10-26 09:01:28 +00:00
mach-antminer-s3.c ar71xx: Bitmain Antminer S1/S3 set GPIO for USB Power 2015-10-26 09:01:28 +00:00
mach-antrouter-r1.c V2 ar71xx : Add Support for the Bitmain Antrouter R1 2016-01-01 21:21:13 +00:00
mach-ap90q.c ar71xx: add support for YunCore CPE830 2016-11-21 10:05:40 +01:00
mach-ap96.c
mach-ap132.c
mach-ap143.c ar71xx: add support for ap143 2015-07-07 08:06:05 +00:00
mach-ap147.c ar71xx: Add support for AP147-010 reference board 2015-07-24 09:09:42 +00:00
mach-ap152.c ar71xx: fix ap152 support 2016-01-10 17:19:34 +00:00
mach-ap531b0.c ar71xx: add support for Rockeetech AP531B0 2017-03-12 17:38:31 +01:00
mach-archer-c7.c Revert "ar71xx: fix Archer C7 LED colour names" 2017-01-27 22:16:24 +01:00
mach-archer-c25-v1.c ar71xx: add support for TP-Link Archer C25 v1 2017-06-11 21:32:18 +02:00
mach-archer-c59-v1.c ar71xx: add support for TP-Link Archer C58 v1 2017-06-29 10:37:36 +02:00
mach-archer-c60-v1.c ar71xx: fix lan ports on archer C59 and C60 2017-02-17 10:30:48 +01:00
mach-arduino-yun.c ar71xx: Arduino Yun board 'WLAN RST' button support 2016-03-10 19:11:13 +00:00
mach-aw-nr580.c
mach-bhr-4grv2.c ar71xx: add support for Buffalo BHR-4GRV2 2016-11-16 10:54:33 +01:00
mach-bhu-bxu2000n2-a.c
mach-bsb.c ar71xx: Add support for Black Swift 2015-08-17 06:16:54 +00:00
mach-c55.c ar71xx: clean up spi controller related patches 2016-12-12 10:22:17 +01:00
mach-c60.c ar71xx: clean up spi controller related patches 2016-12-12 10:22:17 +01:00
mach-cap324.c ar71xx: Kernel board definition for PowerCloud CAP324 2015-12-19 11:27:19 +00:00
mach-cap4200ag.c
mach-carambola2.c ar71xx: update Carambola2 platform data 2014-08-04 14:46:52 +00:00
mach-cf-e316n-v2.c ar71xx: add support for COMFAST CF-E380AC v1 and v2 2016-11-21 10:05:40 +01:00
mach-cpe510.c ar71xx: add support for TP-Link WBS210/510 2017-01-05 16:01:17 +01:00
mach-cpe870.c ar71xx: add support for YunCore CPE870 2016-11-21 10:05:40 +01:00
mach-cr3000.c ar71xx: Kernel board definition for PowerCloud CR3000 2015-12-19 11:27:25 +00:00
mach-cr5000.c ar71xx: Kernel board definition for PowerCloud CR5000 2015-12-19 11:27:32 +00:00
mach-dap-2695-a1.c ar71xx: add support for D-Link DAP-2695 rev. A1 2016-10-27 01:50:42 +03:00
mach-dgl-5500-a1.c add D-link DGL-5500 A1 support 2014-11-27 14:27:34 +00:00
mach-dhp-1565-a1.c ar71xx: Added support for D-link DHP-1565 rev. A1 2014-11-19 09:20:47 +00:00
mach-dir-505-a1.c ar71xx: dir-505: fix reset button gpio active_low value 2015-02-09 12:17:00 +00:00
mach-dir-600-a1.c ar71xx: Add support for D-Link EBR-2310 Rev. C 2017-02-14 12:27:14 +01:00
mach-dir-615-c1.c ar71xx: fix D-Link DIR-615 rev. C1 WLAN MAC address 2015-01-28 19:19:47 +00:00
mach-dir-615-i1.c ar71xx: add support for D-Link DIR-615 rev. Ix board 2015-07-07 13:48:39 +00:00
mach-dir-825-b1.c
mach-dir-825-c1.c
mach-dir-869-a1.c ar71xx: add kernel support for D-Link DIR-869 A1 2016-10-11 22:58:36 +02:00
mach-dlan-hotspot.c ar71xx: add support for the devolo dLAN Hotspot 2015-11-21 21:24:18 +00:00
mach-dlan-pro-500-wp.c ar71xx: add support for the devolo dLAN pro 500 Wireless+ 2015-07-14 07:32:33 +00:00
mach-dlan-pro-1200-ac.c ar71xx: fix AR8337 switch initialization on dLAN pro 1200+ WiFi ac 2016-01-19 10:16:11 +00:00
mach-domywifi-dw33d.c ar71xx: Add support to DomyWifi DW33D 2016-10-25 17:51:08 +02:00
mach-dr344.c ar71xx: fix Wallys DR344 GPIO-connected LEDs and button 2017-05-30 14:34:04 +02:00
mach-dr531.c ar71xx: add support for Wallys DR531 2016-07-13 20:03:10 +02:00
mach-dragino2.c ar71xx: Fix LED definitions for the DRAGINO2 board 2014-10-14 10:33:07 +00:00
mach-e2100l.c ar71xx: Added missing support for Linksys E2100L 2016-12-14 18:42:48 +01:00
mach-eap120.c ar71xx: Add support to TP-Link EAP120 2016-10-18 09:18:55 +02:00
mach-eap300v2.c ar71xx: add kernel support for the EnGenius EAP300 v2 board 2014-07-14 21:30:26 +00:00
mach-eap7660d.c
mach-el-m150.c ar71xx: Fix the sys LEDs on the EasyLink M150 and mini 2014-11-14 16:58:29 +00:00
mach-el-mini.c ar71xx: Fix the sys LEDs on the EasyLink M150 and mini 2014-11-14 16:58:29 +00:00
mach-ens202ext.c ar71xx: add support for EnGenius ENS202EXT 2017-05-30 14:15:25 +02:00
mach-epg5000.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-esr900.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-esr1750.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-ew-dorin.c ar71xx: add status led found on ew-dorin boards 2015-05-10 07:47:04 +00:00
mach-f9k1115v2.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-fritz300e.c ar71xx: add AVM FRITZ!WLAN Repeater 300E support 2017-06-24 22:36:38 +02:00
mach-gl-ar150.c ar71xx: fix LED names for GL Innovations boards 2016-10-04 11:50:50 +02:00
mach-gl-ar300.c ar71xx: fix LED names for GL Innovations boards 2016-10-04 11:50:50 +02:00
mach-gl-ar300m.c ar71xx: set status led for the gl-* boards 2017-03-06 07:50:11 +01:00
mach-gl-domino.c ar71xx: fix LED names for GL Innovations boards 2016-10-04 11:50:50 +02:00
mach-gl-inet.c ar71xx: fix LED names for GL Innovations boards 2016-10-04 11:50:50 +02:00
mach-gl-mifi.c ar71xx: set status led for the gl-* boards 2017-03-06 07:50:11 +01:00
mach-gs-minibox-v1.c ar71xx: Add Gainstrong MiniBox v1.0 support to trunk 2015-10-19 17:55:25 +00:00
mach-gs-oolite.c ar71xx: oolite: the buttons are not active_low 2014-08-01 11:19:34 +00:00
mach-hiveap-121.c ar71xx: add support for Aerohive AP-121 2017-05-15 22:58:59 +02:00
mach-hiwifi-hc6361.c ar71xx: add kernel support for HiWiFi HC6361. 2014-06-02 14:56:24 +00:00
mach-hornet-ub.c Fix (invert/revert) Hornet-UB WPS LED state 2015-03-15 19:25:48 +00:00
mach-ja76pf.c
mach-jwap003.c
mach-jwap230.c ar71xx: add support for jjPlus JWAP230 2016-07-13 20:03:10 +02:00
mach-lima.c ar71xx: add support for 8devices Lima board 2017-02-17 10:19:09 +01:00
mach-mc-mac1200r.c ar71xx: Add support for MERCURY MAC1200R 2015-02-09 12:16:51 +00:00
mach-mr12.c ar71xx: add mac partition to the MR12/MR16 2016-10-26 12:37:45 +02:00
mach-mr16.c ar71xx: add mac partition to the MR12/MR16 2016-10-26 12:37:45 +02:00
mach-mr18.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-mr600.c ar71xx: Fix 2.4G WiFi LED of the OpenMesh MR600 board 2014-08-18 13:09:14 +00:00
mach-mr900.c ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR900 2016-03-23 12:52:09 +00:00
mach-mr1750.c ar71xx: add kernel support for the OpenMesh MR1750v2 2016-05-23 12:19:25 +02:00
mach-mynet-n600.c
mach-mynet-n750.c
mach-mynet-rext.c ar71xx: fix 100/10mbps ethernet link issues on mynet range extender 2015-06-14 17:41:01 +00:00
mach-mzk-w04nu.c
mach-mzk-w300nh.c
mach-nbg460n.c
mach-nbg6716.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-om2p.c ar71xx: add kernel support for the OpenMesh OM2Pv4/-HSv4 2017-02-14 12:18:04 +01:00
mach-om5p.c ar71xx: Increase RXD/RDV to 2 on OM5P-AN 2015-04-20 15:01:00 +00:00
mach-om5pac.c ar71xx: add kernel support for the OpenMesh OM5P-AC board 2016-04-09 10:25:47 +00:00
mach-om5pacv2.c ar71xx: fix build error 2016-04-17 22:03:58 +00:00
mach-omy-g1.c ar71xx: Add support for the OMYlink OMY-G1 2016-04-26 11:44:36 +00:00
mach-omy-x1.c ar71xx: Add support for the OMYlink OMY-X1 2016-03-16 09:26:58 +00:00
mach-onion-omega.c ar71xx: add support for Onion Omega 2015-07-24 09:09:49 +00:00
mach-pb42.c
mach-pqi-air-pen.c ar71xx: add support for PQI Air Pen 2017-01-20 00:52:48 +01:00
mach-qihoo-c301.c ar71xx: qihoo: define flash variable as static 2015-02-07 19:59:02 +00:00
mach-r602n.c ar71xx: add support for P&W R602N and CPE505N 2017-03-23 17:59:47 +01:00
mach-r6100.c Netgear R6100 support 2014-11-26 08:28:22 +00:00
mach-rambutan.c ar71xx: add support for 8devices Rambutan development board 2017-05-15 22:43:33 +02:00
mach-rb4xx.c ar71xx: fix build error 2016-04-17 22:03:58 +00:00
mach-rb91x.c ar71xx: clean up spi controller related patches 2016-12-12 10:22:17 +01:00
mach-rb95x.c ar71xx: Fix UBIFS work on Mikrotik RB95x devices 2017-05-31 11:36:21 +02:00
mach-rb750.c ar71xx: Detect USB port on Mikrotik RB750UP 2017-01-15 17:43:14 +01:00
mach-rb922.c ar71xx: convert mikrotik routerboard support to UBI 2017-01-16 20:40:12 +01:00
mach-rb2011.c Make GBit switch work on RB2011 2017-05-25 09:22:42 +02:00
mach-rbspi.c ar71xx: add support for MikroTik hAP ac 2017-03-23 09:35:14 +01:00
mach-rbsxtlite.c ar71xx: fix machine name for several devices 2017-03-12 17:39:12 +01:00
mach-re450.c ar71xx: add support for TP-Link RE450 2016-12-22 14:50:05 +01:00
mach-rw2458n.c
mach-sc300m.c ar71xx: add Abicom SC300M support 2017-01-20 00:40:27 +01:00
mach-sc450.c ar71xx: add Abicom SC450 support 2017-01-20 00:40:33 +01:00
mach-sc1750.c ar71xx: add Abicom SC1750 support 2017-01-20 00:40:40 +01:00
mach-smart-300.c add support for the NC-LINK SMART-300 2014-08-11 11:44:51 +00:00
mach-som9331.c ar71xx: add support for OpenEmbed SOM9331 2016-06-07 11:21:55 +02:00
mach-sr3200.c ar71xx: add support for YunCore SR3200 and XD3200 2016-12-12 09:57:40 +01:00
mach-tellstick-znet-lite.c ar71xx: add support for the Telldus TellStick ZNet Lite 2016-03-10 19:07:26 +00:00
mach-tew-632brp.c
mach-tew-673gru.c
mach-tew-712br.c
mach-tew-732br.c
mach-tew-823dru.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-tl-mr3x20.c
mach-tl-mr11u.c
mach-tl-mr13u.c ar71xx: Fix LED polarity for the TP-LINK TL-MR13U. 2015-03-10 13:26:50 +00:00
mach-tl-mr3020.c
mach-tl-mr6400.c ar71xx: Add support for TP-Link MR6400 2017-05-27 07:54:21 +02:00
mach-tl-wa701nd-v2.c ar71xx: add support for TL-WA701ND v2 2015-01-20 15:48:07 +00:00
mach-tl-wa801nd-v3.c ar71xx: fix LEDs and sysupgrade support for TL-WA801ND v3 2016-12-06 19:08:35 +01:00
mach-tl-wa830re-v2.c ar71xx: added support for TL-WA830RE V2 2014-07-13 07:12:22 +00:00
mach-tl-wa901nd-v2.c
mach-tl-wa901nd-v4.c ar71xx: add TP-Link TL-WA901ND-v4 support 2016-04-09 10:26:46 +00:00
mach-tl-wa901nd.c
mach-tl-wa7210n-v2.c ar71xx: TL-WA7210n v2 support 2015-02-24 12:00:50 +00:00
mach-tl-wax50re.c ar71xx: add support for TP-Link TL-WA855RE v1 2017-06-29 10:37:36 +02:00
mach-tl-wdr3320-v2.c ar71xx: add TP-LINK TL-WDR3320 v2 support 2015-09-14 20:12:16 +00:00
mach-tl-wdr3500.c
mach-tl-wdr4300.c ar71xx: fix TP-LINK TL-WDR3600/4300 RFKILL switch positions 2015-03-15 19:39:47 +00:00
mach-tl-wdr6500-v2.c ar71xx: register only the built-in switch MDIO bus, hook up eth0 to it, should hopefully fix regression reported in #21520 2016-02-07 21:00:11 +00:00
mach-tl-wpa8630.c ar71xx: fix machine name for several devices 2017-03-12 17:39:12 +01:00
mach-tl-wr703n.c
mach-tl-wr720n-v3.c ar71xx: add support for TL-WR720N-v4. 2015-06-18 18:21:23 +00:00
mach-tl-wr741nd-v4.c
mach-tl-wr741nd.c
mach-tl-wr802n-v2.c ar71xx: add support for TL-WR802N Version 2 2017-02-20 09:10:17 +01:00
mach-tl-wr802n.c ar71xx: add support for TP-Link WR802N v1 2016-10-26 12:37:45 +02:00
mach-tl-wr810n.c ar71xx: add TP-Link TL-WR810N support 2016-05-10 10:43:12 +02:00
mach-tl-wr841n-v8.c ar71xx: add support for the TP-LINK TL-WR941ND v5 2015-02-04 06:10:20 +00:00
mach-tl-wr841n-v9.c ar71xx: fix LED defines for TP-Link TL-WR740N v6 2017-05-30 14:15:25 +02:00
mach-tl-wr841n.c
mach-tl-wr902ac-v1.c ar71xx: add support for TP-Link TL-WR902AC v1 2017-07-04 08:58:54 +02:00
mach-tl-wr940n-v4.c ar71xx: add support for TP-LINK TL-WR940N v4 2016-12-16 11:12:46 +01:00
mach-tl-wr941nd-v6.c ar71xx: add support for TP-LINK TL-WR941ND v6 (international version) 2015-11-08 20:39:18 +00:00
mach-tl-wr941nd.c
mach-tl-wr942n-v1.c ar71xx: add support for TP-Link TL-WR942N v1 2017-06-11 21:32:17 +02:00
mach-tl-wr1041n-v2.c
mach-tl-wr1043nd-v2.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-tl-wr1043nd-v4.c ar71xx: add support for TP-LINK WR1043ND v4 2016-12-20 14:38:48 +01:00
mach-tl-wr1043nd.c
mach-tl-wr2543n.c ar71xx: fix ath9k default LED changes fallout 2017-04-13 08:18:57 +02:00
mach-tube2h.c ar71xx: Ext LNA patch for TUBE2H and HORNET-UB targets 2015-03-12 10:06:53 +00:00
mach-ubnt-unifiac.c ar71xx: add support for UniFi-AC-Mesh 2017-05-15 22:43:33 +02:00
mach-ubnt-xm.c ar71xx: set GPIO reset line for Ubiquiti NanoStation Loco XW 2016-12-04 11:41:50 +01:00
mach-ubnt.c
mach-weio.c ar71xx: Add WeIO Board Support 2015-09-24 09:08:47 +00:00
mach-whr-hp-g300n.c
mach-wlae-ag300n.c
mach-wlr8100.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-wndap360.c ar71xx: fix machine name for several devices 2017-03-12 17:39:12 +01:00
mach-wndr3700.c
mach-wndr4300.c ar71xx: WNDR4300: Fix switch HW controlled LEDs 2017-03-13 00:12:07 +01:00
mach-wnr2000-v3.c ar71xx: add correct named default wireless led by using platform leds 2017-04-08 14:30:00 +02:00
mach-wnr2000-v4.c ar71xx: do general formatting on wnr2000-v4 2015-05-08 12:24:30 +00:00
mach-wnr2000.c ar71xx: Add support for Netgear WNR2000v1 2016-12-14 10:37:01 +01:00
mach-wnr2200.c ar71xx: add correct named default wireless led by using platform leds 2017-04-08 14:30:00 +02:00
mach-wp543.c
mach-wpe72.c ar71xx: compex wpe72 add space to include statement 2015-07-09 07:04:14 +00:00
mach-wpj342.c ar71xx: add support for Compex WPJ342 2016-04-09 10:26:41 +00:00
mach-wpj344.c ar71xx: wpj344: remove unused eth1 device 2017-06-29 10:37:36 +02:00
mach-wpj531.c ar71xx: wpj531: fix GPIOs for LED 2017-03-27 08:36:32 +02:00
mach-wpj558.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-wpj563.c ar71xx: Compex WPJ563 support 2017-03-30 09:57:22 +02:00
mach-wrt160nl.c ar71xx: rename wrt160nl's trx partition parser 2015-03-11 15:56:15 +00:00
mach-wrt400n.c Revert "ar71xx: wrt400n: lift size limit on kernel and rootfs part" 2017-01-20 06:43:13 +01:00
mach-wrtnode2q.c ar71xx: add WRTnode2Q support 2016-06-06 14:58:11 +02:00
mach-wzr-450hp2.c Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x" 2016-03-23 12:52:17 +00:00
mach-wzr-hp-ag300h.c treewide: replace nbd@openwrt.org with nbd@nbd.name 2016-06-07 08:58:42 +02:00
mach-wzr-hp-g300nh.c
mach-wzr-hp-g300nh2.c ar71xx: fix ath9k default LED changes fallout 2017-04-13 08:18:57 +02:00
mach-wzr-hp-g450h.c ar71xx: fix ath9k default LED changes fallout 2017-04-13 08:18:57 +02:00
mach-z1.c ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker Gateway 2016-09-27 17:50:22 +02:00
mach-zbt-we1526.c ar71xx: add support for Zbtlink ZBT-WE1526 2016-08-18 09:49:18 +02:00
mach-zcn-1523h.c
machtypes.h ar71xx: add support for TP-Link TL-WR902AC v1 2017-07-04 08:58:54 +02:00
Makefile ar71xx: add support for TP-Link TL-WR902AC v1 2017-07-04 08:58:54 +02:00
nvram.c ar71xx: add support for TP-Link TL-WR942N v1 2017-06-11 21:32:17 +02:00
nvram.h
pci-ath9k-fixup.c ar71xx: allow pci calibration fixup to work with ar9344 2015-07-07 13:46:44 +00:00
pci-ath9k-fixup.h
routerboot.c ar71xx: routerboot: export extended wlan data via sysfs 2015-04-07 20:03:43 +00:00
routerboot.h ar71xx: routerboot: add support for extended radio data 2015-04-07 20:03:35 +00:00