ar71xx: add support for TP-Link TL-WR942N v1
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit is contained in:
Serg Studzinskii
Piotr Dymacz
parent
641af0c39d
commit
b7cc661615
15 changed files with 370 additions and 2 deletions
|
|
@ -745,6 +745,16 @@ tl-wr840n-v3)
|
|||
ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E"
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
|
||||
;;
|
||||
tl-wr942n-v1)
|
||||
ucidef_set_led_switch "lan1" "LAN1" "$board:green:lan1" "switch0" "0x04"
|
||||
ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08"
|
||||
ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x10"
|
||||
ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02"
|
||||
ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0"
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
|
||||
ucidef_set_led_usbdev "usb1" "USB1" "$board:green:usb1" "1-1.2"
|
||||
ucidef_set_led_usbdev "usb2" "USB2" "$board:green:usb2" "1-1.1"
|
||||
;;
|
||||
tl-wr1043nd|\
|
||||
tl-wr1043nd-v2)
|
||||
ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1"
|
||||
|
|
|
|||
|
|
@ -411,7 +411,8 @@ ar71xx_setup_interfaces()
|
|||
tl-mr3420-v2|\
|
||||
tl-wr841n-v8|\
|
||||
tl-wr842n-v2|\
|
||||
tl-wr941nd-v5)
|
||||
tl-wr941nd-v5|\
|
||||
tl-wr942n-v1)
|
||||
ucidef_set_interfaces_lan_wan "eth1.1" "eth0"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
|
||||
|
|
|
|||
|
|
@ -36,6 +36,7 @@ get_status_led() {
|
|||
db120|\
|
||||
dr344|\
|
||||
tew-632brp|\
|
||||
tl-wr942n-v1|\
|
||||
wpj344|\
|
||||
zbt-we1526)
|
||||
status_led="$board:green:status"
|
||||
|
|
|
|||
|
|
@ -1166,6 +1166,9 @@ ar71xx_board_detect() {
|
|||
*"TL-WR941ND")
|
||||
name="tl-wr941nd"
|
||||
;;
|
||||
*"TL-WR942N v1")
|
||||
name="tl-wr942n-v1"
|
||||
;;
|
||||
*"Tube2H")
|
||||
name="tube2h"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -271,6 +271,7 @@ platform_check_image() {
|
|||
tew-712br|\
|
||||
tew-732br|\
|
||||
tew-823dru|\
|
||||
tl-wr942n-v1|\
|
||||
unifi-outdoor|\
|
||||
unifiac-lite|\
|
||||
unifiac-pro|\
|
||||
|
|
|
|||
|
|
@ -209,6 +209,7 @@ CONFIG_ATH79_MACH_TL_WR841N_V9=y
|
|||
CONFIG_ATH79_MACH_TL_WR941ND=y
|
||||
CONFIG_ATH79_MACH_TL_WR941ND_V6=y
|
||||
CONFIG_ATH79_MACH_TL_WR940N_V4=y
|
||||
CONFIG_ATH79_MACH_TL_WR942N_V1=y
|
||||
CONFIG_ATH79_MACH_TUBE2H=y
|
||||
CONFIG_ATH79_MACH_UBNT=y
|
||||
CONFIG_ATH79_MACH_UBNT_UNIFIAC=y
|
||||
|
|
|
|||
|
|
@ -1695,6 +1695,17 @@ config ATH79_MACH_TL_WR940N_V4
|
|||
select ATH79_DEV_M25P80
|
||||
select ATH79_DEV_WMAC
|
||||
|
||||
config ATH79_MACH_TL_WR942N_V1
|
||||
bool "TP-LINK TL-WR942N v1 support"
|
||||
select SOC_QCA956X
|
||||
select ATH79_DEV_ETH
|
||||
select ATH79_DEV_GPIO_BUTTONS
|
||||
select ATH79_DEV_LEDS_GPIO
|
||||
select ATH79_DEV_M25P80
|
||||
select ATH79_DEV_USB
|
||||
select ATH79_DEV_WMAC
|
||||
select ATH79_NVRAM
|
||||
|
||||
config ATH79_MACH_TL_WR1041N_V2
|
||||
bool "TP-LINK TL-WR1041N v2 support"
|
||||
select SOC_AR934X
|
||||
|
|
|
|||
|
|
@ -214,6 +214,7 @@ obj-$(CONFIG_ATH79_MACH_TL_WR841N_V9) += mach-tl-wr841n-v9.o
|
|||
obj-$(CONFIG_ATH79_MACH_TL_WR941ND) += mach-tl-wr941nd.o
|
||||
obj-$(CONFIG_ATH79_MACH_TL_WR941ND_V6) += mach-tl-wr941nd-v6.o
|
||||
obj-$(CONFIG_ATH79_MACH_TL_WR940N_V4) += mach-tl-wr940n-v4.o
|
||||
obj-$(CONFIG_ATH79_MACH_TL_WR942N_V1) += mach-tl-wr942n-v1.o
|
||||
obj-$(CONFIG_ATH79_MACH_TUBE2H) += mach-tube2h.o
|
||||
obj-$(CONFIG_ATH79_MACH_UBNT) += mach-ubnt.o
|
||||
obj-$(CONFIG_ATH79_MACH_UBNT_UNIFIAC) += mach-ubnt-unifiac.o
|
||||
|
|
|
|||
279
target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c
Normal file
279
target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c
Normal file
|
|
@ -0,0 +1,279 @@
|
|||
/*
|
||||
* TP-Link TL-WR942N(RU) v1 board support
|
||||
*
|
||||
* Copyright (C) 2017 Sergey Studzinski <serguzhg@gmail.com>
|
||||
* Thanks to Henryk Heisig <hyniu@o2.pl>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
* under the terms of the GNU General Public License version 2 as published
|
||||
* by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/ath9k_platform.h>
|
||||
#include <asm/mach-ath79/ar71xx_regs.h>
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/spi/spi_gpio.h>
|
||||
#include <linux/spi/74x164.h>
|
||||
|
||||
#include "common.h"
|
||||
#include "dev-m25p80.h"
|
||||
#include "machtypes.h"
|
||||
#include "dev-eth.h"
|
||||
#include "dev-gpio-buttons.h"
|
||||
#include "dev-leds-gpio.h"
|
||||
#include "dev-spi.h"
|
||||
#include "dev-usb.h"
|
||||
#include "dev-wmac.h"
|
||||
#include "nvram.h"
|
||||
|
||||
#define TL_WR942N_V1_KEYS_POLL_INTERVAL 20
|
||||
#define TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL \
|
||||
(3 * TL_WR942N_V1_KEYS_POLL_INTERVAL)
|
||||
|
||||
#define TL_WR942N_V1_GPIO_BTN_RESET 1
|
||||
#define TL_WR942N_V1_GPIO_BTN_RFKILL 2
|
||||
|
||||
#define TL_WR942N_V1_GPIO_UART_TX 4
|
||||
#define TL_WR942N_V1_GPIO_UART_RX 5
|
||||
|
||||
#define TL_WR942N_V1_GPIO_LED_USB2 14
|
||||
#define TL_WR942N_V1_GPIO_LED_USB1 15
|
||||
|
||||
#define TL_WR942N_V1_GPIO_SHIFT_OE 16
|
||||
#define TL_WR942N_V1_GPIO_SHIFT_SER 17
|
||||
#define TL_WR942N_V1_GPIO_SHIFT_SRCLK 18
|
||||
#define TL_WR942N_V1_GPIO_SHIFT_SRCLR 19
|
||||
#define TL_WR942N_V1_GPIO_SHIFT_RCLK 20
|
||||
#define TL_WR942N_V1_GPIO_LED_WPS 21
|
||||
#define TL_WR942N_V1_GPIO_LED_STATUS 22
|
||||
|
||||
#define TL_WR942N_V1_74HC_GPIO_BASE QCA956X_GPIO_COUNT
|
||||
#define TL_WR942N_V1_74HC_GPIO_LED_LAN4 23
|
||||
#define TL_WR942N_V1_74HC_GPIO_LED_LAN3 24
|
||||
#define TL_WR942N_V1_74HC_GPIO_LED_LAN2 25
|
||||
#define TL_WR942N_V1_74HC_GPIO_LED_LAN1 26
|
||||
#define TL_WR942N_V1_74HC_GPIO_LED_WAN_GREEN 27
|
||||
#define TL_WR942N_V1_74HC_GPIO_LED_WAN_AMBER 28
|
||||
#define TL_WR942N_V1_74HC_GPIO_LED_WLAN 29
|
||||
#define TL_WR942N_V1_74HC_GPIO_HUB_RESET 30 /* from u-boot sources */
|
||||
|
||||
#define TL_WR942N_V1_SSR_BIT_0 0
|
||||
#define TL_WR942N_V1_SSR_BIT_1 1
|
||||
#define TL_WR942N_V1_SSR_BIT_2 2
|
||||
#define TL_WR942N_V1_SSR_BIT_3 3
|
||||
#define TL_WR942N_V1_SSR_BIT_4 4
|
||||
#define TL_WR942N_V1_SSR_BIT_5 5
|
||||
#define TL_WR942N_V1_SSR_BIT_6 6
|
||||
#define TL_WR942N_V1_SSR_BIT_7 7
|
||||
|
||||
#define TL_WR942N_V1_WMAC_CALDATA_OFFSET 0x1000
|
||||
#define TL_WR942N_V1_DEFAULT_MAC_ADDR 0x1fe40008
|
||||
#define TL_WR942N_V1_DEFAULT_MAC_SIZE 0x200
|
||||
|
||||
#define GPIO_IN_ENABLE0_UART_SIN_LSB 8
|
||||
#define GPIO_IN_ENABLE0_UART_SIN_MASK 0x0000ff00
|
||||
|
||||
static struct gpio_led tl_wr942n_v1_leds_gpio[] __initdata = {
|
||||
{
|
||||
.name = "tl-wr942n-v1:green:status",
|
||||
.gpio = TL_WR942N_V1_GPIO_LED_STATUS,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:wlan",
|
||||
.gpio = TL_WR942N_V1_74HC_GPIO_LED_WLAN,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:lan1",
|
||||
.gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN1,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:lan2",
|
||||
.gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN2,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:lan3",
|
||||
.gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN3,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:lan4",
|
||||
.gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN4,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:wan",
|
||||
.gpio = TL_WR942N_V1_74HC_GPIO_LED_WAN_GREEN,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:amber:wan",
|
||||
.gpio = TL_WR942N_V1_74HC_GPIO_LED_WAN_AMBER,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:wps",
|
||||
.gpio = TL_WR942N_V1_GPIO_LED_WPS,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:usb1",
|
||||
.gpio = TL_WR942N_V1_GPIO_LED_USB1,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "tl-wr942n-v1:green:usb2",
|
||||
.gpio = TL_WR942N_V1_GPIO_LED_USB2,
|
||||
.active_low = 1,
|
||||
},
|
||||
};
|
||||
|
||||
static struct gpio_keys_button tl_wr942n_v1_gpio_keys[] __initdata = {
|
||||
{
|
||||
.desc = "Reset button",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RESTART,
|
||||
.debounce_interval = TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = TL_WR942N_V1_GPIO_BTN_RESET,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.desc = "RFKILL button",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RFKILL,
|
||||
.debounce_interval = TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = TL_WR942N_V1_GPIO_BTN_RFKILL,
|
||||
.active_low = 1,
|
||||
},
|
||||
};
|
||||
|
||||
static struct spi_gpio_platform_data tl_wr942n_v1_spi_data = {
|
||||
.sck = TL_WR942N_V1_GPIO_SHIFT_SRCLK,
|
||||
.miso = SPI_GPIO_NO_MISO,
|
||||
.mosi = TL_WR942N_V1_GPIO_SHIFT_SER,
|
||||
.num_chipselect = 1,
|
||||
};
|
||||
|
||||
static u8 tl_wr942n_v1_ssr_initdata[] __initdata = {
|
||||
BIT(TL_WR942N_V1_SSR_BIT_7) |
|
||||
BIT(TL_WR942N_V1_SSR_BIT_6) |
|
||||
BIT(TL_WR942N_V1_SSR_BIT_5) |
|
||||
BIT(TL_WR942N_V1_SSR_BIT_4) |
|
||||
BIT(TL_WR942N_V1_SSR_BIT_3) |
|
||||
BIT(TL_WR942N_V1_SSR_BIT_2) |
|
||||
BIT(TL_WR942N_V1_SSR_BIT_1) |
|
||||
BIT(TL_WR942N_V1_SSR_BIT_0)
|
||||
};
|
||||
|
||||
static struct gen_74x164_chip_platform_data tl_wr942n_v1_ssr_data = {
|
||||
.base = TL_WR942N_V1_74HC_GPIO_BASE,
|
||||
.num_registers = ARRAY_SIZE(tl_wr942n_v1_ssr_initdata),
|
||||
.init_data = tl_wr942n_v1_ssr_initdata,
|
||||
};
|
||||
|
||||
static struct platform_device tl_wr942n_v1_spi_device = {
|
||||
.name = "spi_gpio",
|
||||
.id = 1,
|
||||
.dev = {
|
||||
.platform_data = &tl_wr942n_v1_spi_data,
|
||||
},
|
||||
};
|
||||
|
||||
static struct spi_board_info tl_wr942n_v1_spi_info[] = {
|
||||
{
|
||||
.bus_num = 1,
|
||||
.chip_select = 0,
|
||||
.max_speed_hz = 10000000,
|
||||
.modalias = "74x164",
|
||||
.platform_data = &tl_wr942n_v1_ssr_data,
|
||||
.controller_data = (void *) TL_WR942N_V1_GPIO_SHIFT_RCLK,
|
||||
},
|
||||
};
|
||||
|
||||
static void tl_wr942n_v1_get_mac(const char *name, char *mac)
|
||||
{
|
||||
u8 *nvram = (u8 *) KSEG1ADDR(TL_WR942N_V1_DEFAULT_MAC_ADDR);
|
||||
int err;
|
||||
|
||||
err = ath79_nvram_parse_mac_addr(nvram, TL_WR942N_V1_DEFAULT_MAC_SIZE,
|
||||
name, mac);
|
||||
|
||||
if (err)
|
||||
pr_err("no MAC address found for %s\n", name);
|
||||
}
|
||||
|
||||
static void __init tl_wr942n_v1_setup(void)
|
||||
{
|
||||
u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
|
||||
u8 tmpmac[ETH_ALEN];
|
||||
void __iomem *base;
|
||||
u32 t;
|
||||
|
||||
ath79_register_m25p80(NULL);
|
||||
|
||||
spi_register_board_info(tl_wr942n_v1_spi_info,
|
||||
ARRAY_SIZE(tl_wr942n_v1_spi_info));
|
||||
platform_device_register(&tl_wr942n_v1_spi_device);
|
||||
|
||||
/* Check inherited UART RX GPIO definition */
|
||||
base = ioremap(AR71XX_GPIO_BASE, AR71XX_GPIO_SIZE);
|
||||
|
||||
t = __raw_readl(base + QCA956X_GPIO_REG_IN_ENABLE0);
|
||||
if (((t & GPIO_IN_ENABLE0_UART_SIN_MASK)
|
||||
>> GPIO_IN_ENABLE0_UART_SIN_LSB) == TL_WR942N_V1_GPIO_LED_USB1) {
|
||||
pr_warn("Active UART detected on USBLED's GPIOs!\n");
|
||||
|
||||
tl_wr942n_v1_leds_gpio[9].gpio = TL_WR942N_V1_GPIO_UART_TX;
|
||||
tl_wr942n_v1_leds_gpio[10].gpio = TL_WR942N_V1_GPIO_UART_RX;
|
||||
}
|
||||
|
||||
ath79_register_leds_gpio(-1, ARRAY_SIZE(tl_wr942n_v1_leds_gpio),
|
||||
tl_wr942n_v1_leds_gpio);
|
||||
|
||||
ath79_register_gpio_keys_polled(-1, TL_WR942N_V1_KEYS_POLL_INTERVAL,
|
||||
ARRAY_SIZE(tl_wr942n_v1_gpio_keys),
|
||||
tl_wr942n_v1_gpio_keys);
|
||||
|
||||
tl_wr942n_v1_get_mac("MAC:", tmpmac);
|
||||
|
||||
/* swap PHYs */
|
||||
ath79_setup_qca956x_eth_cfg(QCA956X_ETH_CFG_SW_PHY_SWAP |
|
||||
QCA956X_ETH_CFG_SW_PHY_ADDR_SWAP);
|
||||
|
||||
ath79_register_mdio(0, 0x0);
|
||||
ath79_register_mdio(1, 0x0);
|
||||
|
||||
/* WAN port */
|
||||
ath79_init_mac(ath79_eth0_data.mac_addr, tmpmac, 1);
|
||||
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
|
||||
ath79_eth0_data.speed = SPEED_100;
|
||||
ath79_eth0_data.duplex = DUPLEX_FULL;
|
||||
|
||||
/* swaped PHYs */
|
||||
ath79_eth0_data.phy_mask = BIT(0);
|
||||
ath79_register_eth(0);
|
||||
|
||||
/* LAN ports */
|
||||
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
|
||||
ath79_init_mac(ath79_eth1_data.mac_addr, tmpmac, 0);
|
||||
ath79_eth1_data.speed = SPEED_1000;
|
||||
ath79_eth1_data.duplex = DUPLEX_FULL;
|
||||
|
||||
/* swaped PHYs */
|
||||
ath79_switch_data.phy_poll_mask |= BIT(0);
|
||||
ath79_switch_data.phy4_mii_en = 1;
|
||||
ath79_register_eth(1);
|
||||
|
||||
ath79_register_wmac(art + TL_WR942N_V1_WMAC_CALDATA_OFFSET, tmpmac);
|
||||
|
||||
ath79_register_usb();
|
||||
|
||||
gpio_request_one(TL_WR942N_V1_74HC_GPIO_HUB_RESET,
|
||||
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
|
||||
"USB power");
|
||||
|
||||
gpio_request_one(TL_WR942N_V1_GPIO_SHIFT_OE,
|
||||
GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
|
||||
"LED control");
|
||||
|
||||
gpio_request_one(TL_WR942N_V1_GPIO_SHIFT_SRCLR,
|
||||
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
|
||||
"LED reset");
|
||||
}
|
||||
|
||||
MIPS_MACHINE(ATH79_MACH_TL_WR942N_V1, "TL-WR942N-V1", "TP-LINK TL-WR942N v1",
|
||||
tl_wr942n_v1_setup);
|
||||
|
|
@ -262,6 +262,7 @@ enum ath79_mach_type {
|
|||
ATH79_MACH_TL_WR941ND_V5, /* TP-LINK TL-WR941ND v5 */
|
||||
ATH79_MACH_TL_WR941ND_V6, /* TP-LINK TL-WR941ND v6 */
|
||||
ATH79_MACH_TL_WR940N_V4, /* TP-LINK TL-WR940N v4 */
|
||||
ATH79_MACH_TL_WR942N_V1, /* TP-LINK TL-WR942N v1 */
|
||||
ATH79_MACH_TUBE2H, /* Alfa Network Tube2H */
|
||||
ATH79_MACH_UBNT_AIRGW, /* Ubiquiti AirGateway */
|
||||
ATH79_MACH_UBNT_AIRGWP, /* Ubiquiti AirGateway Pro */
|
||||
|
|
|
|||
|
|
@ -13,6 +13,7 @@
|
|||
#include <linux/errno.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/string.h>
|
||||
#include <linux/etherdevice.h>
|
||||
|
||||
#include "nvram.h"
|
||||
|
||||
|
|
@ -67,7 +68,11 @@ int ath79_nvram_parse_mac_addr(const char *nvram, unsigned nvram_len,
|
|||
t = sscanf(mac_str, "%02hhx:%02hhx:%02hhx:%02hhx:%02hhx:%02hhx",
|
||||
&mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]);
|
||||
|
||||
if (t != 6) {
|
||||
if (t != ETH_ALEN)
|
||||
t = sscanf(mac_str, "%02hhx-%02hhx-%02hhx-%02hhx-%02hhx-%02hhx",
|
||||
&mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]);
|
||||
|
||||
if (t != ETH_ALEN) {
|
||||
ret = -EINVAL;
|
||||
goto free;
|
||||
}
|
||||
|
|
|
|||
|
|
@ -873,6 +873,21 @@ define Device/tl-wr941nd-v6-cn
|
|||
endef
|
||||
TARGET_DEVICES += tl-wr941nd-v2 tl-wr941nd-v3 tl-wr941nd-v4 tl-wr941nd-v5 tl-wr941nd-v6 tl-wr941nd-v6-cn tl-wr940n-v4
|
||||
|
||||
define Device/tl-wr942n-v1
|
||||
DEVICE_TITLE := TP-LINK TL-WR942N v1
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
||||
BOARDNAME := TL-WR942N-V1
|
||||
TPLINK_BOARD_NAME := TLWR942NV1
|
||||
DEVICE_PROFILE := TLWR942
|
||||
IMAGE_SIZE := 14464k
|
||||
KERNEL := kernel-bin | patch-cmdline | lzma | uImageArcher lzma
|
||||
IMAGES := sysupgrade.bin factory.bin
|
||||
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade
|
||||
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
|
||||
MTDPARTS := spi0.0:128k(u-boot)ro,1344k(kernel),13120k(rootfs),64k(product-info)ro,64k(partition-table)ro,256k(oem-config)ro,1344k(oem-vars)ro,64k(ART)ro,14464k@0x20000(firmware)
|
||||
endef
|
||||
TARGET_DEVICES += tl-wr942n-v1
|
||||
|
||||
define Device/tl-wr1041n-v2
|
||||
$(Device/tplink-4mlzma)
|
||||
DEVICE_TITLE := TP-LINK TL-WR1041N v2
|
||||
|
|
|
|||
|
|
@ -172,6 +172,7 @@ CONFIG_ATH79_MACH_RBSXTLITE=y
|
|||
# CONFIG_ATH79_MACH_TL_WR940N_V4 is not set
|
||||
# CONFIG_ATH79_MACH_TL_WR941ND is not set
|
||||
# CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set
|
||||
# CONFIG_ATH79_MACH_TL_WR942N_V1 is not set
|
||||
# CONFIG_ATH79_MACH_TUBE2H is not set
|
||||
# CONFIG_ATH79_MACH_UBNT is not set
|
||||
# CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set
|
||||
|
|
|
|||
|
|
@ -160,6 +160,7 @@ CONFIG_ATH79_MACH_RAMBUTAN=y
|
|||
# CONFIG_ATH79_MACH_TL_WR940N_V4 is not set
|
||||
# CONFIG_ATH79_MACH_TL_WR941ND is not set
|
||||
# CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set
|
||||
# CONFIG_ATH79_MACH_TL_WR942N_V1 is not set
|
||||
# CONFIG_ATH79_MACH_TUBE2H is not set
|
||||
# CONFIG_ATH79_MACH_UBNT is not set
|
||||
# CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set
|
||||
|
|
|
|||
|
|
@ -553,6 +553,43 @@ static struct device_info boards[] = {
|
|||
.last_sysupgrade_partition = "file-system"
|
||||
},
|
||||
|
||||
/** Firmware layout for the TL-WR942N V1 */
|
||||
{
|
||||
.id = "TLWR942NV1",
|
||||
.vendor = "",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"{product_name:TL-WR942N,product_ver:1.0.0,special_id:00000000}\r\n"
|
||||
"{product_name:TL-WR942N,product_ver:1.0.0,special_id:52550000}\r\n",
|
||||
.support_trail = '\x00',
|
||||
.soft_ver = NULL,
|
||||
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"os-image", 0x20000, 0x150000},
|
||||
{"file-system", 0x170000, 0xcd0000},
|
||||
{"default-mac", 0xe40000, 0x00200},
|
||||
{"pin", 0xe40200, 0x00200},
|
||||
{"product-info", 0xe40400, 0x0fc00},
|
||||
{"partition-table", 0xe50000, 0x10000},
|
||||
{"soft-version", 0xe60000, 0x10000},
|
||||
{"support-list", 0xe70000, 0x10000},
|
||||
{"profile", 0xe80000, 0x10000},
|
||||
{"default-config", 0xe90000, 0x10000},
|
||||
{"user-config", 0xea0000, 0x40000},
|
||||
{"qos-db", 0xee0000, 0x40000},
|
||||
{"certificate", 0xf20000, 0x10000},
|
||||
{"usb-config", 0xfb0000, 0x10000},
|
||||
{"log", 0xfc0000, 0x20000},
|
||||
{"radio-bk", 0xfe0000, 0x10000},
|
||||
{"radio", 0xff0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "file-system",
|
||||
},
|
||||
|
||||
/** Firmware layout for the RE450 */
|
||||
{
|
||||
.id = "RE450",
|
||||
|
|
|
|||
Loading…
Reference in a new issue