this commit allows to make a standalone u-boot for nsa310b.
While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
While at it, the following changes are introduced
- Rewrite the Makefile for better readability
- Make parallel builds possible
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This seems to occur when gettext-full is built on the host-side
and the autoreconf stuff re-generates some of the build files,
except for the po/Makefile.in.in
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Even though these fonts may not be installed, they seem to be
generated at build time.
Seems that the configure script re-generated from configure.ac
is a bit more annoying than it has to be.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Reboot of: a0ea22ac43
Reverted: 3c52cbfa53
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Few minor code formatting style fixes, including:
- keep one board per line
- always use "|\" (for consistency)
- remove redundant double quotes and empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
In order to prevent the impact of the merger of the company and the potential
rebase of the SDK repositories, migrate the u-boot source to github.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Based on the submission to the uboot-lantiq repo by Martin Blumenstingl.
Use the ddr_settings.h from the GPL tarball. The NAND boot optimized
one (with memory tuning enabled) doesn't work for the UART boot image.
Use the same mtd layout as the stock u-boot. Add add UBI support.
Use the leds to indicate boot status like it is done with the stock
u-boot. Switch on the red power led if kernel image can't be loaded.
Otherwise switch the green led on.
Make only the ramboot u-boot available. Only this image is required for
the first installation of LEDE.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The current uboot default config for the A13 SOM erroneously enables support
for the AXP209 power regulator IC which is not present on the board.
This superfluous support module sets an incorrect initial clock frequency and
confuses the kernel, ultimately leading to a boot failure later on.
Properly disable the PMIC support and enable the EHCI support by translating
the deprecated SYS_EXTRA_OPTIONS values into proper SUNXI_NO_PMIC and
USB_EHCI_HCD symbols respectively.
Also rename 002-add-olimex-a13-som.diff to 002-add-olimex-a13-som.patch and
refresh the remaining patches of the series while we're at it.
Reported-by: Mario Fischer <mario-fischer@web.de>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Fix the default value for the 'bootcmd' environment variable.
Therefore make the default bootcmd work for buildbot's images.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Fix metadata scan failure in the grub2 package by removing an unexpected
invisible space character and by adding back the missing SECTION variable
which was removed with d140648.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
While enable zynq uboot:
CONFIG_PACKAGE_uboot-zynq-zc702
CONFIG_PACKAGE_uboot-zynq-zed
CONFIG_PACKAGE_uboot-zynq-zybo
make will arise dtc error:
./scripts/dtc-version.sh: line 17: dtc: command not found
./scripts/dtc-version.sh: line 18: dtc: command not found
*** Your dtc is too old, please upgrade to dtc 1.4 or newer
make[4]: *** [checkdtc] Error 1
Pass the kernel dtc to uboot for compile.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
because boot loaders are in Boot Loaders, not in Utilities -> Boot Loaders
Also moved brub2-editenv in Utilities -> Boot Loaders
Part of a wider housekeeping effort on the packages repository.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Boot Loaders submenu of Utilities is the most logical place to find fconfig and other bootloader tools.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Boot Loaders submenu of Utilities is the most logical place to find rbcfg and other bootloader tools.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
OpenWrt uses ancient u-boot thats not reproducible.
There are multiple upstream changes that introduce
reproducible builds like:
859e92b775fd8ebcfacc591eaf621b677c95b6f7
(not used here - the CMD_DATE/TIMESTAMP functionality
seems to be disabled by config)
70d39f57146a6cb94736db39c770c3d95e07bedb
f3f431a712729a1af94d01bd1bfde17a252ff02c
2d9efa1227262249d381ed5d9d341cbdba76e62d
Instead of changing the Makefile too much
this changeset just tries to use the
changes in Makefile from current upstream git f5fd45f
*Should* fix issue reported by reproducible lede page:
https://tests.reproducible-builds.org/lede/lede.html
Compile tested only
(verified w. hexdump & md5sum)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Adds u-boot for the at91 platform and a couple of boards.
The build honours COPTS to benefit from fortify source et al.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Uboot-mvebu isn't a real package, which will break the image builder
when it tries to install it during the packing step. Instead of cleafog
selecting it through its default packages, make it default to m if the
clearfog profile is selected.
This will ensure it is always build, but never added to the rootfs. This
fixes creating images for clearfog with IB.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog image requires u-boot, so package it into KDIR to make sure
it is available in imageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
This allows kobs-ng to flash the SPL successfully on the 4.4 kernel used by
the Gateworks IMX boards supporting NAND. The previous version of kobs-ng
worked with the 3.14 kernel but will brick a board making its SPL unbootable
for the 4.4 kernel.
See http://trac.gateworks.com/wiki/ventana/bootloader#nandspl for instructions
on updating the SPL from Linux.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
tools/env/fw_env.c misses to include stdint.h.
Apparently musl doesn't mind and includes this header by default,
but glibc does not and causes the build to fail.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
In company networks everything except the http and https protocol is
often causes problems, because the network administrators try to block
everything else. To make it easier to use LEDE in company networks use
the https/http protocol for git access when possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Major cleanup and addition of brnboot second stage u-boot was done by
me.
The second stage brnboot u-boot is untested, since the brnboot prompt
is secured by a still unknown password. But should work.
The former ram values are replaced with the ram values extracted from
the original brnboot. The old ones didn't worked with the ramboot
image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The default bootloader partition of some devices is to small for an
u-boot with uncompressed gphy firmware(s).
Instead of increasing the bootloader partition size, in compare to the
stock firmware, compress the firmware. This would allow the bootloader
of at least the FritzBox 3370 as well as the bootloader of the
VGV7510KW22 to fit into the bootloader partition of the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Devices like the xrx200 Arcadyan VGV7519 are using two NOR flash chips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the author, all SPI related configs are copy & paste
leftovers. Which makes sense since nothing is connected to the SPI bus
on this device.
The NOR SPL isn't required for this board, since the NOR is directly
memory mapped.
Allow to overwrite the env in ram while using brn variant. Do not set
the power GPIO pin twice.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use:
- 00nn for u-boot patches
- 01nn for new boards
While doing the rework, the board definitions for the easy50712 and
easy80920 were moved to distinct board definitions patches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
Explicit sets the size of the mtdparts, because the kernel has also an explicit value.
If they have diffent sizes the ubi won't be detected.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49018
otherwise the uboot is missing important commands like bootz
Signed-off-by: Martin Mueller <mm@sig21.net>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49017
Since switching to new ubi(kernel,squashfs,ubifs) layout, the kernel lies in a
ubi volume. Dropping the mtd parts because the mtd layout is saved in the
device-tree, which is appended to the zImage.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49016
Add support for Xilinx ZC702 Dev board
Zynq target is using 4.4 kernel and mainline 2016.1 u-boot.
Patch is tested with Xilinx ZC702 Dev board with SD boot mode.
known issues:
- no QSPI driver in 4.4 kernel: no QSPI flash support
- USB is not working in 4.4 kernel
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
create mode 100644 package/boot/uboot-zynq/Makefile
create mode 100644 target/linux/zynq/Makefile
create mode 100644 target/linux/zynq/base-files.mk
create mode 100755 target/linux/zynq/base-files/etc/board.d/02_network
create mode 100644 target/linux/zynq/base-files/etc/config/network
create mode 100644 target/linux/zynq/base-files/etc/inittab
create mode 100644 target/linux/zynq/config-4.4
create mode 100644 target/linux/zynq/image/Makefile
create mode 100755 target/linux/zynq/image/mkits.sh
create mode 100644 target/linux/zynq/patches-4.4/0001-arm-dts-zynq-zc702.dts-Set-default-rdinit-to-sbin-in.patch
create mode 100644 target/linux/zynq/profiles/zc702.mk
SVN-Revision: 48697
U-boot ships with the `mx6qsabresd` configuration file to configure a
bootloader suitable for booting the Freescale i.MX6q SABRE evaluation board
from SD card. Expose this option in the uboot-imx6 Makefile.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
SVN-Revision: 48014
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
- tested on Beagleboard C4
- remove upstream patches
- disable THUMB mode on OMAP3 this increases binary size
(remove CONFIG_SYS_THUMB_BUILD)
- reduce SPL size by disabling EXT feature
(remove CONFIG_SPL_EXT_SUPPORT)
this fixes 2015.07 and 2015.10-rc3
Beagleboard C4 booting
which were broken by upstream commit
with id: bd2c4522c26d535515aebca52d27c004a7e0c05c
Arm THUMB mode is broken because of an yet unknown errata
see: http://lists.denx.de/pipermail/u-boot/2015-August/225793.html
- backport upstream fix that was introduced in 2015.10-rc5
and was not fixed in 2015.10 final
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47924
gcc-5 handles inline without static differently and that makes
uboot-mxs fail to build. Remove the inline so it gets exported and can
be used in other functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47533
- Use board engineering names rather than marketing names
- Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47429
The current patch to add Duckbill support is wrong and does not
even compile. So replace this patch with a working one.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47007
Install uboot files to KERNEL_BUILD_DIR instead of BIN_DIR to fix
ImageBuilder. Similar fixes are necessary for many (all?) other uboot
targets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46605
Invert the `__GLIBC__` guards into `!__UCLIBC__` ones to avoid
invalid references to `_llseek` on musl.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46125
Add three download mirrors for 'grub', as the Makefile currently defines only
one download location.
@GNU can not be used, as the most recent version of 'grub' is not available
at the general GNU mirrors, and can only be found at the "gnu-alpha" mirrors.
Signed-off-by: Hannu Nyman <hannu.nyman at iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45909
- kexec-tools is now distributed with tarballs of .tar.gz and .tar.xz
format; .tar.bz2 are not provided anymore.
- Add CONFIG_KEXEC_LZMA for selecting lzma support.
Patches are updated along to:
- Remove the now unnecessary patch 0004-mips_regdefs.patch.
- Drop 100-reduce_size.patch because the size reduction is marginal.
- Allow zlib and lzma support coexist together. This patch has been
merged into upstream project.
- Fix kexec-tools' configure.ac.
- Fix a few compilation warnings.
Size comparison of stripped binaries of kexec malta target with both
zlib and lzma support enabled.
- Before: 41447
- After: 42583
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44437
After r43987 TARGET_lantiq_xrx200_P2812HNUFX does not exist anymore.
Fix empty menuconfig bootloader selection by making u-boot depend on
one of the new target profiles.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 44179
KD20 got an IC+ phy, without the driver the phy is not properly
initialized resulting in ethernet not working unless being already
initialized by the vendor loader.
upstream commit 368b4d2b49bbbf379d9334747fbbd2aaaafe4356
drivers: net: remove dead drivers
removed icplus.c due to the lack of in-tree users.
Partially revert that commit adding back the IC+ driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43508
fixes BeagleBoard C4 detection
error message in serial console was:
"WARNING: Could not determine device tree to use"
change is found in upstream u-boot
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 43392
This adds support for the oxnas target in U-Boot 2014.04
History can be found at https://github.com/kref/u-boot-oxnas up to 2013.10
changes from 2013.10 to 2014.04 can be followed at
https://gitorious.org/openwrt-oxnas
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43389
