Instead of each target defining it the same, move the KDIR_TMP
definition to include/image.mk. In addition Image/Build/SysupgradeNAND
already requires KDIR_TMP to be set, so it makes sense to have it
globally defined.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46592
Previous patch 6f2905eeb6ce5ddec8d12d677e1f377a940b537b enabled ADM in
the kernel, which causes a kernel panic when accessing the SPI flash.
As a workaround, We'll disable DMA for the flash for now. It was not
enabled previously anyway so we'll just leave it as is.
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46587
We got check for nvram_len placed too early and the code never tried
reading CFE variables used on WGT634U. This is a regression introduced
in r45942 and reported in #20291.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46584
Previous patch set backported the recently posted NAND flash driver to
3.18 and 4.1 kernel. This patch now enables it in the kernel config.
There is no change to the partition layout and init yet. But the NAND
flash can be seen in the mtd list on an AP148:
root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 10000000 00020000 "qcom-nandc"
...
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46569
These patches add support for ipq806x NAND flash controller. Most of
these are cherry-picked & backported from LKML:
*https://lkml.org/lkml/2015/8/3/16
This patch just modifies the kernel code, but doesn't change the config.
It should be harmless.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46568
These are cherry-picked & backported from LKML:
*https://lkml.org/lkml/2015/3/17/19
They are enabled on both 3.18 and 4.1 kernel. Patches 150 to 154 are
applying changes merged since 3.18; they enable mechanisms used by the
ADM driver.
ADM engine is used by the NAND controller, so it is necessary to
bring-up NAND flash support.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46567
Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used
for template generation, so need to be present before inclusion of
image.mk in target image Makefiles.
So move all declarations to before any includes.
Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46564
It looks like RAC flushes cause random corruption(?) when the
second thread is set as default.
Fixes#20160.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46563
BCM6318: add support for Plusnet / Sagem 2704N (V1)
Signed-off-by: Matt Goring <matt.goring@googlemail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46562
We forgot to enable the stmmac driver for 4.1 kernel, so ethernet
interfaces don't show-up on this kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46559
Old bootloader (same ones which have DT disabled) don't perform any PCIe
initialization. The consequence is a freeze during PCIe bring-up on
these old u-boot. Same kernel with a newer bootloaders works fine as
they contain the corresponding PCIe init code.
In this change, we'll add the missing init and make sure the kernel
doesn't rely on some preexisting init to get PCIe to work. That includes
the following changes:
*GPIOs: set function & drive strength
*Clocks: add init code for aux & ref clocks
*PCIe driver: additional init of the hardware controller
Tested 3.18 and 4.1 on an AP148 with bootloader branch 0.0.1
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46557
PCIe controller nodes are numbers 0/1/2 in the chipset dtsi file, but
the pinmux nodes are numbers 1/2/3. We'll make it consistent by changing
the pinmux numbering to match the controller's one.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46556
Certain AP148 platforms (and derivative) use bootloaders which did not
have DT enabled.
In order to support these old platforms, we'll now make the following
modifications:
*explicitely add the memory node in the AP148 DT: this used to be added
by new u-boot through a run-time patch mechanism. We'll now add it
explicitely so it works on boots which don't support that feature. New
boots will have the node twice, the second one will be ignored.
*add the zImage generation next to the FIT image for AP148.
Other platforms using non-DT enabled bootloaders may want to leverage
this zImage code to generate their own firmare as well.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46555
The generic kernel cmdline parser ignores argv[0], this caused a
regression for all lzma-loader based boards with linux 4.1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46544
Fix for default button states in WRT1900AC dts files.
This prevents overlay wipe when reset is pressed.
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
SVN-Revision: 46530
This patch was missing for kernel 4.0 and 4.1 in r46464. I also
replaced the version in OpenWrt with the version which went upstream
into the Linux mainline kernel.
This closes#20193 and #20192
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46493
Switches BCM63xx to the new IB system.
Images are generated per device definitions.
There are no changes in the produced images except for some name changes,
caused by the new IB system.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46490
Simplify image/Makefile by using the new perl script for RedBoot.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46489
REGMAP_MMIO is a hidden symbol, so it cannot be directly selected. If nothing
selects it, it will fail the build with:
ERROR: module '/store/buildbot/slave/slave/rb532/build/build_dir/target-mipsel_mips32_musl-1.1.10/linux-rb532/linux-3.18.19/drivers/base/regmap/regmap-mmio.ko' is missing.
make[2]: *** [/store/buildbot/slave/slave/rb532/build/bin/rb532/packages/base/kmod-regmap_3.18.19-1_rb532.ipk] Error 1
Fix this by adding a description to allow selecting it manually.
Fixes: r46451 ("kmod-regmap: enable MMIO support")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46485
NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position) and an E3372 device (which mandates NDP
to be after indexed datagrams).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46464
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
There are a few NETGEAR devices which don't terminate the model name in the
ART with a NUL byte, at least some NETGEAR WNDR3700v2. The current awk
expression doesn't match 0xFF bytes, so AR71XX_MODEL contains lots of
trailing 0xFF garbage in this case.
Fix this by matching for the first non-printable character and explicitly
setting LC_CTYPE=C (probably not strictly necessary on OpenWrt, but will
definitely work like this, even when awk supports locales and LANG is set).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46455
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
This ports 9e2a7b779e6f0914395da3657b00f0ac00209bfd to the 4.1 patches.
I forgot this when preparing the initial 4.1 patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46453
As r46245 disabled the board.bin template workaround, 5GHz wifi stopped working
on these devices. This adds them to the calibration data loading introduced in
r46244 and thus makes 5GHz work again for these devices.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
SVN-Revision: 46415
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46405
Now that we have a dtc command that invokes the preprocessor, make use
of it and replace the magic numbers with KEY_* defines.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46391
Now that we have a BuildDTB command, make use of it instead of calling
dtc directly.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46390
This patch adds buttons support for Huawei EchoLife HG553.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46388
Switch brcm63xx to 4.1 to give it some initial testing, but keep 3.18
at least until CC-final is out.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46386
If a link goes down, don't flush the complete ARL table.
Only flush the entries for the respective port.
Don't touch ARL table if a link goes up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46381
Adds functions for flushing ARL table entries per port.
Successfully tested on AR8327. Implementation for AR8216/AR8236/AR8316
is based on the AR8236 datasheet and assumes that the three chips
share a common ATU register layout.
Compile-tested only for AR8216/AR8236/AR8316.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46380
Adds the chip-specific part of reading ARL table for AR8216/AR8236/AR8316.
It's based on the AR8236 datasheet and compile-tested only as I couldn't
find datasheets for AR8216/AR8316 and don't own devices with these chips.
The existing ar8216_atu_flush implementation was used for all three
chip types, therefore I guess they share a common ATU register layout.
More testing would be appreciated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 46379
All modules should be build by a package and only selected by such a
package. Remove all the config options selected as module and also
refresh the config.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46372
One argument was removed with kernel 4.1 from xhci_handshake() which
caused a compile error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46369
Since r40909 openwrt can automatically shutdown when you press the
power button or try to shutdown a kvm virtual machine.
When booting a recent CC-rc2 or trunk image, it doesn't work,
as two kernel modules are missing.
Add these two kernel modules to the default packages, so users
don't need to install them manually.
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 46366
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46361
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.
Signed-off-by: Tom Deng <2579131212@qq.com>
SVN-Revision: 46349
USB port of TP-Link Archer C20i does not work with trunk and CC.
This patch adds two nodes (ehci and ohci) to the device tree enabling USB.
Signed-off-by: Gunnar Thorburn <gunnar@thorburn.se>
SVN-Revision: 46348
Implement sysupgrade for Raspberry Pi, similar to the way it is done on x86:
The config files are saved in the boot partition and moved to where they are
normally expected in preinit.
Also add optional gzip compression for the SD card image, since this can save
a lot of space (76M vs 6M), also similar to x86.
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 46347
- only sunxi has this disabled
- unify kernel configuration across platforms
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46307
commit r46299 broke the mvebu target because one patch does not apply
any more. This commit closes#20070.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46303
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.
Fix Ethernet by setting the right values.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 46281
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46280
This patch adds the RFKill GPIO control switch and enables another GPIO to
control power supply to USB Ports by emulating an LED GPIO for WDR4900v1.
Signed-off-by: Guo Wei Lim <alphasparc@gmail.com>
SVN-Revision: 46279
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
The mips reloc patch introduced new allocations which were done before
add_unformed_module but never freed them in case of an error. A new hook in
Linux 3.19 called module_arch_freeing_init can be used for freeing memory
which were allocated during this init phase.
The problem can be seen when trying to load a module (via busybox insmod)
when it was already loaded.
free -m
for i in `seq 1 100`; do
/sbin/insmod /lib/modules/*/ath9k.ko >& /dev/null
done
free -m
This simple loop would leak ~3.2 MB.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46247
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
This device is identical to the TL-WR740N v5, it even uses the same HWID (which
wasn't the case for older TL-WR741ND revisions).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46238
Backport for the Spansion S25FL164K
It's a 8 MiB flash chip with 4 KiB erase sectors.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46237
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
Add features ext4 targz to target x86/xen_domu in order to
generate images in defconfig.
This fixes#18074.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 46233
Basically the only error I am seeing is "Correctable Error". Also newer
lantiq PCIe drivers have this message wrapped in a "if debug enabled"
block. So it should be safe to disable this warning.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46222
Newer DSL driver versions depend on the address information.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46221
This is useful if the device also has an ethernet WAN interface with a
separate mac address (that is derived from the LAN mac address).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46220
Make it consistent with the net_device struct and the xrx200 driver
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46219
All (still relevant) patches were refresh.
The following patches were dropped because they are applied upstream:
- 0003-MIPS-lantiq-handle-vmmc-memory-reservation.patch
- 0005-MIPS-lantiq-add-reset-controller-api-support.patch
- 0006-MIPS-lantiq-reboot-gphy-on-restart.patch
- 0009-MIPS-lantiq-command-line-work-around.patch
- 0010-MIPS-lantiq-export-soc-type.patch
- 0011-lantiq-add-support-for-xrx200-firmware-depending-on-.patch
- 0037-MIPS-lantiq-move-eiu-init-after-irq_domain-register.patch
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46216
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46206
r45954 ("ar71xx: fix 100/10mbps ethernet link issues on mynet range
extender") introduced a pdata based modification of the tx_clk_dly. But it
was not checked if pdata actually existed. This caused a page fault on all
devices which didn't have at803x_platform_data specified for an at803x
based device.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46200
Update firmware name and md5sum. MAC-address location remains
unchanged from previous version.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46196
- it should be BOARDNAME instead of BOARD_NAME
- kernel partition should be padded to 1536k (somehow this padding was lost in translation to BuildCode in bc797c73f6328941b2194d144385655ad9297e7c)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46193
EPG5000 uses ath79 nvram functions, but does not select it. This breaks
build if no other board support enabling nvram support is selected.
Closes#19952.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46190
Some machtypes were dropped when 4.0 support was added, and the
incomplete patch was taken over to 4.1.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46187
Code calling fpu_emulator_cop1Handler will pass on fault_addr, making gcc
complain about it not being initialized when the FPU emulator is disabled.
Fixes:
arch/mips/kernel/traps.c: In function 'do_fpe':
arch/mips/kernel/traps.c:864:22: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
process_fpemu_return(sig, fault_addr, fcr31);
^
arch/mips/kernel/traps.c: In function 'do_ri':
arch/mips/kernel/traps.c:806:22: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
process_fpemu_return(sig, fault_addr, fcr31);
^
arch/mips/kernel/traps.c:763:15: note: 'fault_addr' was declared here
void __user *fault_addr;
^
arch/mips/kernel/traps.c: In function 'do_cpu':
arch/mips/kernel/traps.c:1421:28: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (!process_fpemu_return(sig, fault_addr, fcr31) && !err)
^
cc1: all warnings being treated as errors
make[7]: *** [arch/mips/kernel/traps.o] Error 1
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46184
Backport a commit from 4.2 making IRQCHIP_DECLARE available outside of
drivers/irqchip and use it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46183
Replace the appended dtb patch with the upstream accepted version and
update the code to work with the changed interface.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46181
The AT91 SAMA5D3XPLAINED uses a KSZ9031 and a KSZ8081 that are supported
by this PHY driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 46171
The position of the nvram header file on brcm47xx changed with kernel
version 4.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46170
r46161 updated headers also touched by it, so it needed to be refreshed
as well.
Closes#20033.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46165
Make some network uapi headers detect if they are included after
not only glibc but also musl headers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46161
Also move it to an earlier place so new boards added are less likely
to confuse quilt.
Fixes#19965.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46148
Follow upstream patch and handle it using &uart0. Also disable &uart1 as
it's most likely unused. This will allow us to get valuable reports and
upstream these changes.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46140
This patch adds the missing parts to use the upstream Broadcom PCIe
driver and makes use of it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46130
Instead of setting the l2c_aux_val variable in the board code make it
possible to set these through device tree and make use of that.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46129
This only removes the patches already applied upstream and makes the
rest apply cleanly.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46128
TP-Link ships wr740n v5.0 to Romania (so probably everywhere except
China) with 4 MB flash and 32 MB memory (confirmed by their local
support). This patch adds support for the v5.0 clone of v4, i just
tested it on my own v5.0 router and it works.
Signed-off-by: Daniel Petre <daniel.petre@posteo.net>
SVN-Revision: 46115
Boot tested: http://pastebin.com/L6aAb9xj
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo:
update to 4.1 final
add patches added since submission
delete patches applied in later rcs
restore commit messages in 220-gc-sections and 304-mips_disable_fpu
fix 050-backport_netfilter_rtcache to match new API
update inlined dma ops with upstream changes
add missing config symbols
enabled CONFIG_MULTIUSER
update kmod defintions for 4.1
]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46112
On two tested devices: Netgear R6250 (BCM53011 rev 2) and Luxul XWC-1000
(BCM53011 rev 3) it was possible to use port 7 and eth1 (instead of port
5 and eth0). It seems BCM53011 just like BCM53012 has 8 ports and
usually 3 of them are connected to the SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46104
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46046
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46043
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
SVN-Revision: 46041
Some devices ship with NAND images that use BCH ECC. Let the driver know
about that ECC mode so that it can be selected by machine files.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
SVN-Revision: 46022
It seems that there are maximum timings for mdio accesses that can be
hit when the system is under load and the thread is scheduled during
a read or write access. Since there is no way of knowing if this
happens as there is not even a parity bit, try to work around it
by disabling interrupts during any gpio-mdio accesses.
Performance impact seems to be neglectable, as mdio accesses are not
that often.
Hopefully fixes#19500.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46012
This stabilizes USB support. The old patch was handling initialization
in a different order that was causing some problems with few USB 3.0
devices. Some weren't detected, some were working unstable, sometimes
USB 3.0 could hang the whole controller.
A still known issue (but not a regression) is controller hang triggered
by connecting USB 1.1 device when not having OHCI controller enabled
(kmod-usb-ohci).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45997
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
This patch adds the pll_1000 value for eth0 interface. This makes the Rocket M
XW image compatible with other Ubiquiti devices with similar hardware with a
Gigabit Ethernet port.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45965
The *u-boot-initramfs* images are not ITB/FIT images but are rather
supposed to be loaded to RAM and jumped-into.
To avoid confusion, change the file extension from itb to bin.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45963
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes#19751, bug introduced in #45624
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 45958
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 45954
When r42245 moved A4001N to DT based detection the image padding size
was accidentally increased from 4 to 8 MiB. This made images unflashable
on these devices.
Fixes#19836.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45945
On device reset the sizes for the vlan and port tables were wrongly
calculated based on the pointer size instead of the struct size. This
causes buffer overruns on 64 bit targets, resulting in panics.
Fix this by dereferencing the pointers.
Reported-by: Fedor Konstantinov <blmink@mink.su>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45938
At least on my b53 chip, the mask is 3 bits wide, and because
of this some STP states are not set properly and discarded when read.
Maybe for some other chips it makes sense to have just 2 bits width,
but I don't have other versions around to test/validate.
If that's the case then maybe we could add another STP state mask.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45937
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45919
Extracting TRX to separated file in /tmp/ just wastes some RAM while we
can just pass a proper extracting command to the default_do_upgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45912
Extracting full TRX out of vendor format is not needed as otrx supports
passing TRX offset. This saves some RAM during sysupgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45911
The v1 identifies as v10 internally. As there is no TL-WA830RE v10, add a
workaround to avoid confusing users.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45903
Version 2 : White spaces and alphabetical order problems
fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware
Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>
SVN-Revision: 45902
Extracting TRX to separated file in /tmp/ requires extra RAM which may
not be available on some chepaer devices. Instead of that lets pass a
proper extracting command to the default_do_upgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45901
if there is any new tx need to clean up. do it in next napi poll.
collect tx related members to fe_tx_ring struct. for better
cache usage and more readable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 45895
when open device. first ready napi software rx.
then enable hardware interrupt.
final start software tx queue to send data.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 45894
Avoid the use of memory marked as reserved
MT7621 support 512MB memory.
According to "MT7621_ProgrammingGuide_Preliminary_Platform.pdf"
0x0~0x1c000000 448MB
0x20000000~0x4000000 64MB
total 512MB
Signed-off-by: wengbj <fl.service@t-firefly.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45892
This also adds the old hardcoded value to the VGV7519BRN profile to make
sure that images are still generated correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45882
Livebox does need the uncompressed kernel, so just create it during
image generation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45875
Ethernet GMAC is built-in the SoC, so there is no need to enable it as a
module. We'll just assume we need it. That's what is done for other
platform where this driver is used so it'll make things more consistent.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45871
Delete the dtb appended, uncompressed kernels after having compressed
them, so they don't end in the image builder.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45869
In r44391 the kernel partion size was increased to allow larger kernels,
but the rootfs partition offset was missed. Fix this by setting the
rootfs offset to the expected value.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45868
I didn't figure out how to achieve this using uci-defaults-new.sh,
so use old-school uci-defaults script as that's what is used on
realview as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45857
Building the loader in Image/Build/TPLINK-SAFELOADER would break the image
builder as no target compiler is available in that stage.
Fixes#19580
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45855
In contrast to Image/BuildLoader, Image/BuildLoaderPatched first patches the
kernel command line in the image and then builds the loader without command
line. This allows building loaders for systems which don't boot correctly when
the kernel command line is provided by the loader (like the TP-LINK CPE series).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45854
Most boards use pci connected usb controllers, so make sure to include
the pci drivers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45840
This is the case e.g. if JFFS2 partition is full.
see: https://www.mail-archive.com/linux-unionfs@vger.kernel.org/msg00246.html
(a small error in a logmessage was changed and reported upstream)
runtime tested on ar71xx with kernel 3.18.11 and r45772
this paritially fixes#19564
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
Acked-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45833
This driver has been cherry-picked and backported from the following
LKML thread:
*https://lkml.org/lkml/2015/5/26/744
It also updates the DT accordingly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45831
Most ipq806x platforms use an ethernet switch, and the new upstream
GMAC driver makes use of the Fixed PHY emulation to force the link
settings despite the lack of PHY.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45830
STMMAC_PLATFORM and STMMAC_PCI have been added recently in the kernel,
but show up only when STMMAC driver is enabled. So se'll add it in the
generic config, so the kernel build doesn't stall whenever we enable
this driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45828
This include is necessary starting at the PCIe patch, which has a lower
number. So in order to keep the patches consistent, we'll move the
arm-gic include in the first patch who needs it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45827
Turn on the auto recovery feature when flashing
and turn it off on successful bootup.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45792
With this patch the following two patches are backported:
* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down
The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45783
Update kernel sources and refresh some patches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45761
