Commit graph

15258 commits

Author SHA1 Message Date
Luka Perkov
7b931ba95c imx6: ventana: fix GW16083 device-tree patch
The 206-ARM-imx-ventana-added-GW16083-to-device-tree.patch merged wrong in
the conversion from 3.18 to 4.1. This patch resolves that and puts the
device-tree nodes in the correct place.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 47510
2015-11-18 22:06:50 +00:00
Luka Perkov
5f3d29f4e6 imx6: drop support for kernel 3.18
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47509
2015-11-18 21:36:36 +00:00
Luka Perkov
03401fed5e imx6: convert ventana images to squashfs+ubifs overlay
Replace the ventana ubi images from a single rootfs volume containing the
rootfs as well as kernel+dtbs in the boot/ subdir to a multi-volume ubi
containing kernel+dtbs+bootscript in 'root' ubifs volume, rootfs in 'rootfs'
squasfs volume, and rootfs_data an empty ubifs volume.

At the same time move ventana image creation over to using the new
TARGET_DEVICE syntax as a cleanup.

Additionally removed FIT image creation as it is recommended that this be
done manually to produce signed FIT images if needed.

Note that a bootscript is needed for Ventana to change its default mtdparts
to rename the 2nd partition from 'rootfs' to 'ubi'. This is because there
are patches in OpenWrt kernels that try to auto-attach and auto-mount and these
get in the way if the mtd partition is named 'rootfs'.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 47508
2015-11-18 21:35:24 +00:00
Luka Perkov
ca26bf8932 imx6: kernel: add UBI_BLOCK support
UBI_BLOCK support is needed for mounting squashfs over UBI

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 47507
2015-11-18 21:35:16 +00:00
Luka Perkov
486dc85e72 imx6: switch to v4.1
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>

SVN-Revision: 47506
2015-11-18 21:35:12 +00:00
Luka Perkov
8c65560497 imx6: add Gateworks GW551x support
Upstream patch: e9d6d6b62f306ba83e1441af5daf2809a6167474

Add support for the Gateworks GW5510 board featuring:
 * i.MX6 SoC
 * up to 512MB DDR3
 * up to 2GB NAND flash
 * 1x miniPCIe socket (with USB)
 * HDMI out (micro-HDMI)
 * HDMI in (micro-HDMI) (currently supported by only vendor kernel)
 * TTL level I/O (supported by GW16111 breakout board):
  * I2C
  * 2x UART
  * CAN
  * 2x DIO (GPIO/PWM)
  * USB OTG

Also add support to OpenWrt build system

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>

SVN-Revision: 47505
2015-11-18 21:35:09 +00:00
Luka Perkov
84c7a31535 kirkwood: nsa310s: fix partition size
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47504
2015-11-18 21:35:04 +00:00
Rafał Miłecki
ce7bf20101 kernel: add CONFIG_SSB_HOST_SOC symbol
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47486
2015-11-16 12:22:47 +00:00
Rafał Miłecki
f8692a4b88 brcm47xx: backport BCM47xx MIPS commits from 4.3 and 4.4-rc1
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47484
2015-11-16 07:18:37 +00:00
Rafał Miłecki
b2dab45aa7 kernel: backport ssb changes from 4.4-rc1
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47483
2015-11-16 06:55:38 +00:00
Felix Fietkau
acd0e4b8dd octeon: remove 3.18 support
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 47474
2015-11-15 21:33:33 +00:00
Felix Fietkau
3cb722b875 octeon: switch to 4.3
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 47473
2015-11-15 21:33:28 +00:00
Felix Fietkau
33305b56a2 octeon: add support for 4.3
Runtime tested on Ubiquiti EdgeRouter Lite.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 47472
2015-11-15 21:33:23 +00:00
Felix Fietkau
1f8864c046 kernel: add patch to fix prefsrc lookups
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 47471
2015-11-15 21:33:14 +00:00
Felix Fietkau
06f79fe841 ipq806x: enable vfpv4 support and set cpu type to cortex-a9
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47468
2015-11-14 14:22:24 +00:00
Hauke Mehrtens
cb0c8da7c2 kernel: take bcm47xx_nvram.h from kernel and not backports
compat-wireless/backports now contains a bcm47xx_nvram.h file to
backport some of the functions in it which are used by the bcmfmac
driver. This file just checks for the kernel versions and provide an
empty implementations on older kernel versions. This is OK on most
systems, but on bcm47xx / bcm53xx systems we want to call the real
functions here. This commit removes the file from backports in our
build process like we do it with the bcma and ssb header files. Instead
we add a recent version into our kernel so all code uses only one
header file. On bcm47xx / bcm53xx the real implementations of this code
will be used.

Reported-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47467
2015-11-13 23:51:31 +00:00
Felix Fietkau
8a2a1c1d71 kernel: fix an af_packet regression that was breaking PPPoE on 4.1+ (#20707)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47459
2015-11-11 14:12:51 +00:00
Luka Perkov
4e239d9fdb kirkwood: add Linksys routers to default profile
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47458
2015-11-11 12:48:30 +00:00
Hauke Mehrtens
f38dbb89c2 kernel: add missing config options
This was seen by the buildbot on arm64.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47452
2015-11-10 23:21:10 +00:00
Hauke Mehrtens
fa137d51f5 ar71xx: add Arduino Yun
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83

The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.

Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47451
2015-11-10 23:13:09 +00:00
Hauke Mehrtens
1bfbf2de6d ar71xx: serial: core: add support for boot console with arbitrary baud rates
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 230400 Baud.

With this patch Linux will use the configured baud rate and not some
standard one which is near by.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47450
2015-11-10 23:11:10 +00:00
Hauke Mehrtens
abea1127c9 ar71xx: add function to access the GPIO function2 register
Add access to the function2 gpio register. This probably has to be
converted into a pimux driver later on. This is needed for some setup
functions on the Arduino Yun.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47449
2015-11-10 23:10:11 +00:00
Felix Fietkau
99af1cf410 kernel: fix breakage in the 4.3 version of 611-netfilter_match_bypass_default_table.patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47447
2015-11-10 21:11:25 +00:00
Felix Fietkau
8b5d644bb3 toolchain: add support of ARC architecture
This includes binutils, gcc, gdb and uClibc-ng.

Latest release of ARC gcc (as of today it is "arc-2015.06")
is based on upstream gcc 4.8.4.

Sources are available on GitHub, see:
https://github.com/foss-for-synopsys-dwc-arc-processors/gcc

Latest release of ARC binutils (as of today it is "arc-2015.06")
is based on upstream binutils 2.23.

Sources are available on GitHub, see:
https://github.com/foss-for-synopsys-dwc-arc-processors/binutils-gdb/releases/tag/arc-2015.06

Latest release of ARC GDB (as of today this is "arc-2015.06-gdb")
is based on upstream gdb 7.9.1.

Sources are available on GitHub, see:
https://github.com/foss-for-synopsys-dwc-arc-processors/binutils-gdb/releases/tag/arc-2015.06-gdb

Note that for binutils and gdb that come from unified git repository
(which is the case for upstream binutils/gdb today) we need to disable
building of gdb in binutils and binutils in gdb hence in binutils:
------>8------
--disable-sim
--disable-gdb
------>8------

and in gdb:
------>8------
--disable-binutils
--disable-ld
--disable-gas
------>8------

Also in gdb we disable sim because if the following breakage while
building with it:
------------>8------------
/usr/bin/env bash ./../common/genmloop.sh -shell /usr/bin/env bash \
        -mono -fast -pbb -switch sem5-switch.c \
        -cpu a5f -infile ./mloop5.in \
        -outfile-suffix 5
unknown option: bash
Makefile:699: recipe for target 'stamp-5mloop' failed
make[7]: *** [stamp-5mloop] Error 1
------------>8------------

Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

SVN-Revision: 47438
2015-11-10 12:03:59 +00:00
Luka Perkov
ba26e9f60f kirkwood: rename EA3500/EA4500 profiles
Match the engineering board names now used elsewhere.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47436
2015-11-10 00:17:01 +00:00
Luka Perkov
31c7de0313 kirkwood: add diag LED on Linksys EA3500
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47435
2015-11-10 00:16:56 +00:00
Luka Perkov
b0e7ca4f8f kirkwood: support sysupgrade on Linksys EA[34]500
This automatically writes to the alternate firmware partition
(on Linksys's dual firmware layout) using code borrowed from
the WRT1900AC port.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47434
2015-11-10 00:16:42 +00:00
Luka Perkov
ea8ac0999c kirkwood: support Linksys boot counter on EA[34]500
This is done with existing code from the WRT1900AC port.
It makes sure the "auto_recovery" bootloader option is set,
and resets the s_env boot counter after a successful boot.

This gives users without a serial console connection some
measure of safety.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47433
2015-11-10 00:16:37 +00:00
Luka Perkov
6acb552eee kirkwood: generate factory images for Linksys EA[34]500
This is done with the new image generation system and board names.
It also generates a sysupgrade.tar image.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47432
2015-11-10 00:16:35 +00:00
Luka Perkov
5d4bbb5f5b kirkwood: find active Linksys root partition
This is imported verbatim from the mvebu WRT1900AC port.

It picks up the current boot partition from the kernel command line,
then renames that partition "ubi" so that it auto-mounts.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47431
2015-11-10 00:16:33 +00:00
Luka Perkov
ad8f6370de kirkwood: consistently use engineering board names
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47430
2015-11-10 00:16:28 +00:00
Luka Perkov
3ef14d0c3d kirkwood: rework Linksys EA[34]500 DTS
- Use board engineering names rather than marketing names

- Linksys uses a dual firmware layout, where the bootloader
  will switch to the other stored image when one fails to
  boot three consecutive times.

  In order to make this firmware compatible with the factory
  images and the stock bootloader we must match this layout.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47429
2015-11-10 00:16:24 +00:00
Luka Perkov
49db4924d7 kirkwood: enable squashfs-on-ubiblock support
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47428
2015-11-10 00:16:14 +00:00
Felix Fietkau
23fbd97649 x86: add generic profiles to x86_64, kvm_guest and xen_domu
The imagebuilder requires a profile for every subtarget to work.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47421
2015-11-08 20:39:24 +00:00
Felix Fietkau
7f75961e38 ar71xx: add support for TP-LINK TL-WR941ND v6 (international version)
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.

This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 47420
2015-11-08 20:39:18 +00:00
Felix Fietkau
0a96564f9b ar71xx: fix typo in r47416
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47417
2015-11-07 18:33:45 +00:00
Felix Fietkau
9dd5c79c47 ar71xx: fix alignment of struct arpt_arp (fixes #14577)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47416
2015-11-07 16:22:38 +00:00
Felix Fietkau
ad133b57a9 kernel: remove linux 4.0 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47412
2015-11-07 16:22:08 +00:00
Felix Fietkau
b95aed986a ramips: minor fixes for mt7621 profiles
* remove references to non-existing kmod-usb3-mt7621
 * ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47407
2015-11-07 12:51:48 +00:00
Felix Fietkau
846b8593fc ar71xx: add support for the TP-LINK TL-WR1043ND v3
The hardware of the v3 is identical to the v2.

Based-on-patch-by: Andreas Ziegler <github@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 47406
2015-11-07 12:51:43 +00:00
Felix Fietkau
ae7e7239b8 ar71xx: Add support for ZyXEL NBG6616.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>

SVN-Revision: 47405
2015-11-07 12:51:39 +00:00
Felix Fietkau
46f6626052 include/image.mk: Introduce generic option to wrap kernel into JFFS2
Some devices require the kernel to be in a JFFS2 file system. Make the
support for this more generic so that it can be used by other devices.

Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>

SVN-Revision: 47404
2015-11-07 12:51:31 +00:00
John Crispin
aebf73f045 ramips: fix previous commit
r47388 accidentially changed 2 files too many

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47389
2015-11-05 10:03:58 +00:00
John Crispin
dc699dd547 ramips: minor tweak to the lks7688 baord name
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47388
2015-11-05 10:01:23 +00:00
Luka Perkov
47668ffd8e kirkwood: add support for 4.3
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47386
2015-11-04 22:28:47 +00:00
Luka Perkov
805492bda9 kirkwood: pogo_e02: use mainline led definitions
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47385
2015-11-04 22:28:42 +00:00
Luka Perkov
122fadaa00 kernel: update kernel 4.3-rc7 to version 4.3
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47384
2015-11-04 22:28:40 +00:00
Jonas Gorski
d9197d8b0c ipq806x: fix BOARD_NAME spellings
the board names used by the upgrade check differ from the device names
in case, so always set them. We can't rely on tolower or similar since
different locales might have different rules for lower case letters, so
set them explicitily.

Fixes sysupgrade rejecting *-sysupgrade.tar because of the difference.

Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 47381
2015-11-04 11:33:31 +00:00
Jonas Gorski
1e43316cb9 brcm63xx: fix brcm, bcm6345-ext-intc interrupt controller
brcm,field-width is read but unused

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 47379
2015-11-04 11:33:16 +00:00
Jonas Gorski
64af3295cd brcm63xx: fix Netgear CVG834G HCS magic bytes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 47378
2015-11-04 11:33:10 +00:00
Jonas Gorski
8f3cfe4ba2 brcm63xx: lzma-loader: add BCM3380 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 47377
2015-11-04 11:33:07 +00:00
Jonas Gorski
4c43b05dac brcm63xx: lzma-loader: add BCM3368 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 47376
2015-11-04 11:33:03 +00:00
Jonas Gorski
a15f148cf8 brcm63xx: fix BCM3368 external interrupts
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 47375
2015-11-04 11:32:55 +00:00
John Crispin
2350c149b5 ramips: add feature to blink led on sysupgrade
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47373
2015-11-03 13:32:02 +00:00
Felix Fietkau
0b296d3808 ar71xx: use correct PLL configuration register bitmask for QCA956x SoC.
Incorrect value causes clock inaccuracy as huge as 1/60.

Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47363
2015-11-02 18:20:51 +00:00
John Crispin
25afe99b31 mediatek: add support for the new MT7623 Arm SoC
the support is still WIP. next steps are to make the pmic and ethernet work.
this is the first commit to make sure nothing gets lost.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47354
2015-11-02 10:18:50 +00:00
John Crispin
165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
John Crispin
0f4b153e3d ramips: add eeprom mtd partition to the Asus RP-N53 dts
This patch adds the eeprom property to the dts for the Asus RP-N53. It is necessary to get the wifi in the soc working.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47350
2015-11-02 10:18:09 +00:00
John Crispin
907c67fa87 ramips: preinit: use iproute2 instead of vconfig
Replace use of vconfig with the corresponding iproute2 syntax in
/lib/preinit/07_set_preinit_iface_ramips

The switch reset work-around needed on some ramips targets used the
deprecated vconfig tool to bring up the pre-init/failsafe interface.
This doesn't work on recent builds where vconfig is no longer being
deployed, resulting in the device being unreachable when triggered
into failsafe mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47349
2015-11-02 10:18:02 +00:00
John Crispin
3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin
83693c911a ramips: add function to change rt2x00 wifi eeprom mac
Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom.
Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47347
2015-11-02 10:17:41 +00:00
John Crispin
a76de8e7b3 ramips: mt7620 add icplus phy driver kernel config symbol
Add missing icplus phy driver kernel config symbol to mt7620 subtarget.
This is needed since some mt7620 devices have icplus ip1001 ethernet transceiver

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47346
2015-11-02 10:17:35 +00:00
John Crispin
8fa6927415 ramips: add support for the Asus RP-N53 in the "02_network" boot script
This patch adds a case for the Asus RP-N53 in the "02_network" boot script. Without this, the lan interface does not get configured on startup, effectively bricking the device.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47345
2015-11-02 10:17:26 +00:00
John Crispin
7cc3beff32 ar71xx: Add support for wdr7500v3
The device is similar to Archer C7 v2, but with 8M of flash, and 6 external
antennas.  Reason for breaking the naming pattern is that sticker on the back
mentions "WDR7500" and has no mention of "Archer".

Signed-off-by: Srdjan Rosic <rosic@google.com>

SVN-Revision: 47344
2015-11-02 10:17:15 +00:00
John Crispin
e5e196b5b9 omap/Beagleboard: remove FEATURES override
It overrides the feature list of the whole target.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47343
2015-11-02 10:17:09 +00:00
John Crispin
ed30ca8e39 ramips: rt305x: enable seama mtdsplit parser
D-Link DIR-610 A1 needs seama mtdsplit parser.
This patch should fix #18046.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 47341
2015-11-02 10:16:56 +00:00
John Crispin
6dcbf74a94 ramips: rt305x: update kernel config symbols
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 47340
2015-11-02 10:16:48 +00:00
John Crispin
4f9fcd94bd package/devel/perf: fix build for kernel 4.1
This fix contains 2 parts:
 - kernel 4.1: backport upstream patch "perf build: Do not fail on missing Build file"
 - add NO_LZMA=1 to perf MAKE_FLAGS to disable LZMA support

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>

SVN-Revision: 47338
2015-11-02 10:16:28 +00:00
Rafał Miłecki
d2c1087536 bcm53xx: Netgear R8000: define GPIO powering USB ports
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47337
2015-11-01 22:21:59 +00:00
Rafał Miłecki
c348b3317a bcm53xx: replace USB patch fixing power control with the most recent version
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47336
2015-11-01 22:21:49 +00:00
Hauke Mehrtens
55a912f43e kernel: update kernel 3.18 to version 3.18.23
Changelog:
 * https://cdn.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.22
 * https://cdn.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.23

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47334
2015-11-01 13:45:57 +00:00
Felix Fietkau
9130e4dc32 ar71xx: fix regression in building TL-WDR6500-v2 images
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47333
2015-11-01 12:38:44 +00:00
Felix Fietkau
6bc9a6d0a8 imx6: add v4.1 support
Build and boot tested on the following hardware:
 * GW54xx
 * GW53xx
 * GW52xx
 * GW51xx

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>

SVN-Revision: 47331
2015-11-01 12:19:32 +00:00
Luka Perkov
6a18146206 kirkwood: add initial support for NSA310s
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47330
2015-11-01 01:13:16 +00:00
Luka Perkov
013a114691 generic: 3.18: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47329
2015-11-01 00:04:21 +00:00
Felix Fietkau
faabe8e8e6 malta: make eth0 the wan interface by default
Many packages for OpenWrt currently assume that lan is the "internal"
side of the network map, e.g. if installed, dnsmasq will hand out DHCP
leases on lan, firewall will allow forwarding on lan.

While at it, also configure a lan interface if eth1 exists.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 47326
2015-10-31 09:30:57 +00:00
Felix Fietkau
8ddca59465 malta: use as a default type device
There is currently no relevant definition for developerboard device type
in include/target.mk, thus packages like iptables, firewall, dnsmasq
etc. are missing in the default images, rendering it almost useless
for regular testing or normal use.

With this change, currently a default set of packages for "router" will
be installed to malta firmware images.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 47325
2015-10-31 09:30:37 +00:00
Felix Fietkau
c5c2eb5fd6 malta: set CPU_TYPE:=24kc.
There are instructions (e.g. wsbh) only available in MIPS32R2 which is
the isa level used by many MIPS targets in OpenWrt.  As we use the malta
target mostly for development and testing purposes, setting the CPU_TYPE
to 24Kc will make the emulation more real.

The following is output from qemu-system-mipsel 2.3.0

    root@OpenWrt:/# cat /proc/cpuinfo  | grep 'cpu model\|isa'
    cpu model               : MIPS 24Kc V0.0  FPU V0.0
    isa                     : mips1 mips2 mips32r1 mips32r2

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 47324
2015-10-31 09:30:14 +00:00
Felix Fietkau
93efeef9b3 generic: fix unrecognized opcode wsbh when building for MIPS16.
The issue was found and reported by hynman [1] when compiling reaver for ar71xx
(Big Endian MIPS).

    {standard input}: Assembler messages:
    {standard input}:79: Error: unrecognized opcode `wsbh $2,$2'
    {standard input}:90: Error: unrecognized opcode `wsbh $3,$17'
    {standard input}:208: Error: unrecognized opcode `wsbh $2,$2'
    make[3]: *** [builder.o] Error 1

The patch was already in upstream since kernel release 4.3-rc5.

 [1] 1e29676a8a (commitcomment-12901931)

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 47322
2015-10-31 09:29:57 +00:00
Felix Fietkau
180713b89b ar71xx/image: remove old unused build code for TPLINK
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47321
2015-10-31 09:29:48 +00:00
Felix Fietkau
958c785868 ar71xx/image: remove old unused build code for TPLINKOLD
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47320
2015-10-31 09:29:38 +00:00
Felix Fietkau
24eb0d1ba1 ar71xx/image: migrate tl-wr841nd-v1.5 to new build step using squashfs+jffs2 instead of squashfs-only
All other tplink images use squashfs+jffs2. I don't see any reason why
this board should use squashfs-only

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47319
2015-10-31 09:29:25 +00:00
Felix Fietkau
ebea23b49f ar71xx/image: remove old unused build step TPLINK-64K
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47318
2015-10-31 09:29:18 +00:00
Felix Fietkau
c3350394a5 ar71xx/image: migrate tl-wdr6500-v2 to new image build steps
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47317
2015-10-31 09:29:09 +00:00
Felix Fietkau
1bd87413e6 ar71xx/image: refactor templates tplink-chn-v2
SVN-Revision: 47316
2015-10-31 09:29:01 +00:00
Felix Fietkau
153ed674b3 ar71xx/image: introduce TPLINK_HEADER_VERSION variable for tplink image
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47315
2015-10-31 09:28:50 +00:00
Felix Fietkau
ea23d796f6 oxnas: image: Remove custom mkfs targz override as base should be fine now
It was wrong anyway, missing file sort order parameter which was fixed
in base month ago.

Signed-off-by: Petr Štetiar <ynezz@true.cz>

SVN-Revision: 47314
2015-10-31 09:28:42 +00:00
Felix Fietkau
2e7df6312d kirkwood: image: Remove custom mkfs targz override as base should be fine now
It was wrong anyway, missing file sort order parameter which was fixed
in base month ago.

Signed-off-by: Petr Štetiar <ynezz@true.cz>

SVN-Revision: 47313
2015-10-31 09:28:34 +00:00
Felix Fietkau
f5683a0a86 imx6: image: Remove custom mkfs targz override as base should be fine now
It was wrong anyway, missing file sort order parameter which was fixed
in base month ago.

Signed-off-by: Petr Štetiar <ynezz@true.cz>

SVN-Revision: 47312
2015-10-31 09:28:25 +00:00
Felix Fietkau
74d9ef96f1 oxnas: image: Refactor sanitize_profile_name using PROFILE_SANITIZED variable
Signed-off-by: Petr Štetiar <ynezz@true.cz>

SVN-Revision: 47310
2015-10-31 09:28:05 +00:00
Felix Fietkau
8a237d1f03 kirkwood: image: Refactor sanitize_profile_name using PROFILE_SANITIZED var
Signed-off-by: Petr Štetiar <ynezz@true.cz>

SVN-Revision: 47309
2015-10-31 09:27:56 +00:00
Felix Fietkau
e09d32dd96 imx6: image: Refactor sanitize_profile_name using PROFILE_SANITIZED variable
Signed-off-by: Petr Štetiar <ynezz@true.cz>

SVN-Revision: 47308
2015-10-31 09:27:49 +00:00
Felix Fietkau
b100027a83 ramips: fix for kernel 4.0 napi repoll need return budgets number
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47306
2015-10-30 22:32:49 +00:00
Felix Fietkau
9cd525a7fa x86/generic: enable radeon drm driver
This enables modesetting for radeon based boards.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>

SVN-Revision: 47305
2015-10-30 22:32:41 +00:00
Felix Fietkau
63f2b8afbf x86/generic: enable pata_atiixp driver
This enables booting from devices that use an ATI PATA controller for
the boot device, such as the embedded CF cards in Fujitsu-Siemens Futro
thin-clients.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>

SVN-Revision: 47304
2015-10-30 22:32:19 +00:00
Felix Fietkau
05d6b87cfb x86/generic: refresh subtarget kernel config
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>

SVN-Revision: 47303
2015-10-30 22:32:12 +00:00
Felix Fietkau
0365ce46df kernel: add some missing symbols for 4.3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47302
2015-10-30 22:32:04 +00:00
Felix Fietkau
61366c95e2 realview: Create ext4 image by default
Following the additions in r46924, enable the 'ext4' feature for
realview target so the ext4 image is created by default.

Signed-off-by: Dov Murik <dov.murik@gmail.com>

SVN-Revision: 47301
2015-10-30 22:31:47 +00:00
Felix Fietkau
65558ba722 kernel: backport some bcma header file definitions from wireless-testing
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47284
2015-10-30 15:17:41 +00:00
Felix Fietkau
e2ebbfab40 kernel: add missing config symbol
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47283
2015-10-30 15:17:34 +00:00
Rafał Miłecki
0a8196818d bcm53xx: add missing Netgear R8000 LEDs
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47282
2015-10-30 14:44:06 +00:00
Rafał Miłecki
e6944a3490 bcm53xx: add workaround for Netgear R8000 network
According to the info from NVRAM we should use port 8 for the CPU (and
interface eth2). Unfortunately it doesn't work right now, so lets switch
to the port 5.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

Forwardport of r46586 from 15.05

SVN-Revision: 47281
2015-10-30 12:55:37 +00:00
John Crispin
7fe0940c69 generic: fix adm6996 init
Kernel 3.14 added aditional genphy_soft_reset phy reset to phy_init_hw in drivers/net/phy/phy_device.c
Since adm6996 does in driver soft reset and doesn't use BMCR_RESET for soft reset
add dummy soft_reset callback to adm6996 driver, like it is done in ar8216.

This fixes ticket #20147

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47272
2015-10-26 10:39:53 +00:00
John Crispin
c89fc7a75a kernel: Fix environment pointer setup in ar71xx/ath79
Observed on ar71xx/ath79 platforms such as Ubiquiti RouterStations.Reported in #20642.:
(https://dev.openwrt.org/ticket/20642).

If embedded command-line text exists with CONFIG_IMAGE_CMDLINE_HACK=y,firmware
init doesn't initialize environment pointer (fw_init_cmdline not called).

arcs_cmdline is not initialized before calling strlcat.

Signed-off-by: Ted Hess <thess@kitschensync.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 47270
2015-10-26 10:39:41 +00:00
John Crispin
c466a46a77 ar71xx: add support for TP-LINK TL-WR841N/ND v10
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 47263
2015-10-26 09:01:41 +00:00
John Crispin
c9426352ce ar71xx: fix ath79_soc_rev value for QCA9531 ver. 2
ath9k expects to get revision id 2 for the QCA9531 ver. 2 rev. 0. This
fixes the very low TX power on some devices like the TP-LINK
TL-WR841ND v10.

As ath79_soc_rev is only used to get the revision number to ath9k on the
QCA9533, just set it to the expected value on the ver. 2.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Tested-by: Felix Kaechele <felix@kaechele.ca>

SVN-Revision: 47262
2015-10-26 09:01:34 +00:00
John Crispin
632c92094a ar71xx: Bitmain Antminer S1/S3 set GPIO for USB Power
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 47261
2015-10-26 09:01:28 +00:00
John Crispin
f080f2aa8e brcm2708: copy overlays README to boot partition
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47260
2015-10-26 09:01:21 +00:00
John Crispin
71ca5b1cc5 brcm2708: update modules
- Add support for DAC+ Pro.
- Add kmod-smi-bcm2835 and kmod-smi-bcm2835-dev modules.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47259
2015-10-26 09:01:12 +00:00
John Crispin
bf28fb50bf brcm2708: update 4.1 patches
As usual, this patches were taken (and rebased) from
https://github.com/raspberrypi/linux/commits/rpi-4.1.y

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47258
2015-10-26 09:01:05 +00:00
John Crispin
228eeb647e ramips: make the alsa driver register the codec
this allows using the codec even if it is not listed in the DTS

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47256
2015-10-26 09:00:42 +00:00
John Crispin
56dcd0fe90 rb532: prepare switch to 4.1
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 47255
2015-10-26 09:00:35 +00:00
Hauke Mehrtens
ff64ae8293 lantiq: add clk_round_rate()
This adds a basic implementation of clk_round_rate()
The clk_round_rate() function is called by multiple drivers and
subsystems now and the lantiq clk driver is supposed to export this,
but doesn't do so, this causes linking problems like this one:
ERROR: "clk_round_rate" [drivers/media/v4l2-core/videodev.ko] undefined!

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47254
2015-10-25 22:46:46 +00:00
Hauke Mehrtens
4fd9028f44 bcm53xx: add clk tree driver
These patches are written by Broadcom and will be in mainline Linux
kernel soon. I had some problems to get them backported to kernel 4.1,
so currently they are only available for 4.3.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47253
2015-10-25 22:46:08 +00:00
Hauke Mehrtens
da94b00df5 kernel: update kernel 4.1 to version 4.1.11
https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.11

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47252
2015-10-25 17:32:01 +00:00
Hauke Mehrtens
fa4395db04 bcm53xx: add support basic for kernel 4.3
The files directory is now split up into the files which are needed for
every kernel version and the files only needed by kernel 4.1. The files
in files-4.1 are already merged into mainline kernel 4.3. This patch
only removed patches which were merged into mainline kernel 4.3.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47251
2015-10-25 16:43:14 +00:00
Hauke Mehrtens
6bc8640163 kernel: update kernel 4.3 to version 4.3-rc7
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47250
2015-10-25 16:13:34 +00:00
Hauke Mehrtens
e67b786afe bcm53xx: add missing patch from r47248 for USB 3.0
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47249
2015-10-23 22:38:07 +00:00
Hauke Mehrtens
aaa20ae2c2 bcm53xx: update USB 3.0 driver with version submitted upstream
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47248
2015-10-23 22:32:38 +00:00
Hauke Mehrtens
5682b0d954 bcm53xx: use Broadcom's proposed SMP implementation
This replaces our SMP implementation with a very similar version which
is Broadcom currently trying to get into mainline kernel.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47247
2015-10-23 22:29:05 +00:00
Hauke Mehrtens
dc01c61664 bcm53xx: Add BCM SVK DT files
Add device tree files for Broadcom Northstar based SVKs.  Since the
bcm5301x.dtsi already exists, all that is necessary is the dts files to
enable the UARTs.  With these files, the SVKs are able to boot to shell.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47246
2015-10-23 22:26:49 +00:00
John Crispin
e043ada1d5 ramips: gpio-mt7621 was not handling irqs above 31 properly
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47238
2015-10-20 07:09:20 +00:00
John Crispin
fb152a810c ar71xx: Send power to USB port on WNR2200
This patch fixes ticket #15267 by enabling power on the
WNR2200's USB port. At present, the USB port on the WNR2200
is non-functional due to it not receiving power.

This patch defines an additional GPIO pin, but none of the
current GPIO definitions have been modified.

Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch>

SVN-Revision: 47236
2015-10-19 18:18:12 +00:00
John Crispin
8d8a937272 ar71xx: Add Gainstrong MiniBox v1.0 support to trunk
This patch supersedes the v1 from September 17th.

Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.

The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).

Fixed items:

- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.

Compiles fine, has been confirmed working by owners on 15.05.

Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?

Thank you

Signed-off by: Stijn Segers <francesco.borromini@inventati.org>

SVN-Revision: 47234
2015-10-19 17:55:25 +00:00
John Crispin
257e76a3df ar71xx: Bitmain Antminer S1 & S3 cleanup
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 47221
2015-10-19 10:10:02 +00:00
John Crispin
024083a556 generic: add 8139cp fixes, enable hardware csum/tso on 4.0+
This contains two sets of fixes for the 8139cp driver.

For all kernel versions older than 4.3, we can apply the fixes from the
4.3-rc4 kernel. In particular, these fix the TX timeout recovery which
is causing my Geos to lock up until the hardware watchdog kicks in.

For 4.0 and later kernels, we can also apply the additional improvements
which are going into 4.4 to fix and enable hardware checksum/TSO
offload. Backporting those to older kernels is non-trivial.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

SVN-Revision: 47220
2015-10-19 10:09:54 +00:00
John Crispin
6944a95091 oxnas: move gmac soc glue from mach to stmmac driver
Still a lot of kernel-version ifdef'ery, but imho that's easy to remove
once obsoleted and avoids duplicate code in the meantime.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47218
2015-10-19 10:09:36 +00:00
John Crispin
54b8ddf9e7 oxnas: prepare pinctrl for kernel >=4.2
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47217
2015-10-19 10:09:30 +00:00
John Crispin
26329f650c oxnas: prepare irqchip driver for kernel >=4.2
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47216
2015-10-19 10:09:23 +00:00
John Crispin
392b93f579 oxnas: fix duplicate include in clk-oxnas
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47215
2015-10-19 10:09:16 +00:00
John Crispin
ec9ffe892f oxnas: remove obsolete __cpuinit
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47214
2015-10-19 10:09:07 +00:00
John Crispin
e1d585d99f lantiq: Synchronize access to the DSL command pipe
Whenever two processes were executing different commands at the same
time then one of the commands sometimes got the response of the other
command.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47213
2015-10-19 10:08:56 +00:00
John Crispin
b7e4c8d3bf lantiq: Print the status register whenever an error occurs
This should help finding potential problems with the SPI driver.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47209
2015-10-19 10:08:29 +00:00
John Crispin
2c7d536780 lantiq: Fixed reading the number of RX FIFOs in the SPI driver
Until now the SPI driver used the TX bits for the RX FIFO. This seems
uncritical for now since both are equals on my devices (VR9), but this
could cause problems on other SoCs.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47208
2015-10-19 10:08:18 +00:00
John Crispin
42c9a85e8e Revert "lantiq: activate spi-xway on TDW89X0"
This reverts commit 68c2e4789b4f071ee75d39248f4d08fe8283eb28.

commit r47159 was bad

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47207
2015-10-19 10:08:12 +00:00
John Crispin
7295e9fb8b ramips: add alsa support
add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960.
mt7620 is only compile tested.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47205
2015-10-19 10:07:54 +00:00
John Crispin
f5d5cb0114 ramips: add a baurate hack
When talking to an atmel controller we need 9600 or 250000 baud.
as 250000 does not exist we use 2500000.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47204
2015-10-19 10:07:43 +00:00
John Crispin
51dd991d39 ramips: add LinkIt Smart7688 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47203
2015-10-19 10:07:38 +00:00
Hauke Mehrtens
a90135949f brcm47xx: remove support for kernel 3.18
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47199
2015-10-17 11:50:16 +00:00
Hauke Mehrtens
99a468a9dd bcm53xx: remove support for kernel 3.18
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47198
2015-10-17 11:49:01 +00:00
Hauke Mehrtens
b5842aed82 kernel: generic: add kernel 4.3
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47182
2015-10-11 19:08:08 +00:00
John Crispin
f457ae99f2 lantiq: fix use of IRQF_DISABLED in lantiq kmods
The IRQF_DISABLED flag was removed in kernel 4.1 with commit
"genirq: Remove the deprecated 'IRQF_DISABLED' request_irq() flag entirely" [1].

Therefore the compilation of ltq-hcd and ltq-vmmc kmods fails.

[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=d8bf368d0631d4bc2612d8bf2e4e8e74e620d0cc

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47180
2015-10-11 16:24:43 +00:00
John Crispin
c9ef7a49c7 ar71xx: TP-LINK Archer C5 image name
There are more version on market, add version number to the name.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 47179
2015-10-11 16:24:31 +00:00
John Crispin
d6ac3faec3 ar71xx/image: migrate all images based on macro TPLINK
Includes images for
rnx-n360rt
tl-mr3220-v1
tl-mr3420-v1
tl-wa701n-v1
tl-wa730rev1
tl-wa7510n
tl-wa801nd-v1
tl-wa830re-v1
tl-wa901nd-v1
tl-wa901nd-v2
tl-wr740n-v1
tl-wr740n-v3
tl-wr743nd-v1
tl-wr841nd-v3
tl-wr841nd-v5
tl-wr841nd-v7
tl-wr842n-v1
tl-wr941nd-v2
tl-wr941nd-v3
tl-wr941nd-v4
tl-wr1043nd-v1

SVN-Revision: 47178
2015-10-11 16:24:22 +00:00
John Crispin
abe9f6b025 ar71xx/image: remove old build step TPLINK-LZMA
all boards has been migrated to the new build step

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47177
2015-10-11 16:24:10 +00:00
John Crispin
b2e3f71b7c ar71xx/image: migrate last TPLINK-LZMA images to new build system
Migrate TLWR1043V2 TLWR2543

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47176
2015-10-11 16:24:01 +00:00
John Crispin
16517293ac ar71xx/image: refactor tplink-chn-v2 devices
* use build step mktplinkfw with extra arguments
* remove now unused mktplinkfw-chn-v2
* use Device/tplink

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47175
2015-10-11 16:23:53 +00:00
John Crispin
5816fa9a98 ar71xx/image: add options argument to mktplinkfw step
Allow to pass extra arguments to mktplinkfw step. Some board requires
an extra argument to create a valid image.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47174
2015-10-11 16:23:44 +00:00
John Crispin
6f59ea0e80 ar71xx/image: remove unused multiprofile definitons
These profiles covered by new image/Makefile descriptions. Only the old format uses
MultiProfile macro

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 47173
2015-10-11 16:23:35 +00:00
John Crispin
2fc473cf3f lantiq: bugfix wrong non pre-emptive crc errors output
This patch fixes a wrong non pre-emptive crc errors output of
dsl_control.sh status.

Signed-off-by: Luca Debernardi <luca.debernardi@gmail.com>

SVN-Revision: 47172
2015-10-11 16:23:26 +00:00
John Crispin
4412334bea brcm2708: use mmd for overlays subdirectory
Fixes https://dev.openwrt.org/ticket/20704

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47171
2015-10-11 16:23:18 +00:00
John Crispin
0be23c40f3 brcm2708: all sound overlays require i2c to work
Tested on RPi B+ with HiFiBerry Amp+

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47169
2015-10-11 16:23:01 +00:00
Luka Perkov
9c7336e0f9 imx6: fix platform checking
Fix platform checking when configuring networks and when doing sysupgrade.

Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>

SVN-Revision: 47168
2015-10-10 12:35:02 +00:00
Michael Büsch
56ee706379 omap24xx: Append dtb to the zImage
We just hardcode the n810 dtb for now. It should be selectable via profiles.

SVN-Revision: 47166
2015-10-09 07:46:12 +00:00
Imre Kaloz
8bb23cfb66 mvebu: add support for the Linksys WRT1900ACS (Shelby)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 47164
2015-10-08 10:01:30 +00:00
John Crispin
02197db96f lantiq: activate spi-xway on TDW89X0
use the hardware spi core in favour of spi-gpio.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47159
2015-10-07 12:12:48 +00:00
John Crispin
33f9165a63 lantiq: spi driver fix
adds a missing wait busy. based on the UGW patch 2060..

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47158
2015-10-07 12:12:35 +00:00
Michael Büsch
f0b83fd20f omap24xx: Add missing kconfig options
SVN-Revision: 47155
2015-10-07 09:40:42 +00:00
Michael Büsch
d5e9530692 omap24xx: KERNEL_PATCHVER:=4.1
SVN-Revision: 47154
2015-10-07 08:30:58 +00:00
Michael Büsch
5112dbca9a omap24xx: Remove 4.0
SVN-Revision: 47153
2015-10-07 08:29:06 +00:00
John Crispin
2210e821e1 lantiq: bugfix luci lantiq_dsl status
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Helge Mader <hmader@tdt.de>
Reported-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47152
2015-10-07 08:00:54 +00:00
John Crispin
b0f7e6bc83 ramips: fix /target/linux/ramips/dts/HC5XXX.dtsi
dtb complained about those lines

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47151
2015-10-07 08:00:40 +00:00
Felix Fietkau
2686dc6dd8 ramips: enable mt76 by default for the mt7620 subtarget (for devices with mt7620 + mt7612)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47146
2015-10-06 12:32:31 +00:00
Felix Fietkau
38389c79c2 ramips: improve read performance of the m25p80 chunked io patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47137
2015-10-05 11:34:16 +00:00
John Crispin
a0543c2bdc lantiq: several ARV7519RW22 fixes
Fixes ARV7519RW22 flash register (only 1 flash).
Power LED is green, not red.
Rename message LEDs to internet.
Add LEDs configuration (lan, wan, power).
Enable switch VLANs.
Fix secondary USB.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>

SVN-Revision: 47132
2015-10-05 10:28:34 +00:00
John Crispin
2795592d91 lantiq: make v4.1 the default kernel
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47131
2015-10-05 10:28:26 +00:00
John Crispin
161179f40b lantiq: Add target TP-Link TD-W8980
The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz
wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47130
2015-10-05 10:28:19 +00:00
John Crispin
f2f50ad762 lantiq: fix ath_pci_fixup hang on bridged devices
Port of r41856.

In contrast to the brcm63xx target, it isn't sufficient to enable/disable
the bridge. The device needs to be enabled/disabled to fix the hang. The
bridge will be automatically enabled by the time the connected device is
enabled.

Fixes boot on TD-W8980.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47129
2015-10-05 10:28:12 +00:00
John Crispin
c5cc3d9610 lantiq: Change the data-type of mac address in ETOP driver
This adds the changes from r46219 to the linux 4.1 patches as well.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47128
2015-10-05 10:28:07 +00:00
John Crispin
cea7c66ef8 lantiq: bugfix uninitialized variables
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Reported-by: Sylwester Petela <sscapi@gmail.com>

SVN-Revision: 47127
2015-10-05 10:27:55 +00:00
John Crispin
7ce3e1fd3c brcm2708: keep boot partition mounted to allow users to change config.txt
This way it's easier to configure device tree overlays, customize other
parameters...

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47126
2015-10-05 10:27:49 +00:00
John Crispin
d1fc19265a brcm2708: add support for device tree overlays
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47125
2015-10-05 10:27:41 +00:00
John Crispin
b97498ab29 brcm2708: switch device tree compilation to linux
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47124
2015-10-05 10:27:34 +00:00
John Crispin
a32acfe73c brcm2708: fix kmod-sound-soc-bcm2708-i2s config
Right now, selecting kmod-sound-soc-bcm2708-i2s causes build errors due to
missing configs.
kmod-regmap enables I2C and SPI, causing build errors due to depending
variables not defined.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47123
2015-10-05 10:27:18 +00:00
John Crispin
b4db6d29d3 ramips: improve systick timer
when sleep mode is disable use MIPS as clocksource and clockevent instead of systick.
because MIPS timer has higher resolution 5ns less than systick 20us and
larger counter bits 32 > 16.
clean interrupt by write compare register at isr.
fix typo cause sleep mode not enable.

Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47122
2015-10-05 10:27:09 +00:00
John Crispin
10f75a2b7f ramips: fix use remove_irq to release irqaction resource
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47121
2015-10-05 10:27:04 +00:00
John Crispin
ccf89e71f2 ramips: add support for 16MB VoCore
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47120
2015-10-05 10:27:00 +00:00
John Crispin
948e67cb16 ramips: fix size-cells for spi nodes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47119
2015-10-05 10:26:54 +00:00
John Crispin
d4cd8f89eb ramips: Ralink RT3883 RGMII pinmux fix.
Due to datasheet of rt3883 SoC rgmii1 port handles pins 84-95 and rgmii2 port handles pins 72-83. When this function ports gets added to rt3883_pinmux_data there's wrong pinmux bits set (RT3883_GPIO_MODE_GE1 manages 84-95 pins and RT3883_GPIO_MODE_GE2 manages 72-83). So when enabling rgmii2 as GPIO driver confuses hardware and nothing work, neither rgmii nor gpio.
Also in '0030-pinctrl-ralink-add-pinctrl-driver.patch' typo in name of rgmii2 port.

Signed-off-by: Nick Leiten <nickleiten@gmail.com>

SVN-Revision: 47118
2015-10-05 10:26:40 +00:00
John Crispin
aecac14cc4 ramips: Enable rx of 1536 bytes ethernet frames on MT7621
The default switch frame size (with FCS + header) is 1536 bytes. But the
GMAC only accepted frames up to 1522 bytes. Setting it to 1536 allows to
receive ethernet frames using the full of MTU 1500 + an extra VLAN header +
VLAN header added by the switch.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 47117
2015-10-05 10:26:34 +00:00
John Crispin
7b306e3eb3 ramips: Fix too small rx buffer
The driver assumes that the maximum received buffer for non-jumbo frames is
1536 bytes. But the allocation of the rx fragment doesn't reflect that. It
currently allocates fragments which will only be large enough to be used as
rx buffer with the size of 1534 bytes. This is problematic because the GMAC
will now try to write to 2 bytes which don't belong to its receive buffer
when a large enough ethernet frame is received.

This may already be a problem on existing chips but will at least become a
problem when the 1536 byte rx modus is enabled on MT7621a. It is required
on this SoC to receive ethernet frames which use their full 1500 bytes MTU
and a VLAN header next to the switch VLAN tag.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 47116
2015-10-05 10:26:28 +00:00
John Crispin
6b4985b105 ramips: Fix setting of rx buffer length
The length of the DMA rx buffer was always set to 0 because the function
for extracting the length was used to calculate the value for setting it.
Instead the macro has to be split in a get and set function similar to the
TX_DMA_(GET_|)PLEN(0|1) macro.

No problem was noticed on MT7621a before this was changed and thus maybe it
was hidden by different problem which is not yet fixed.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 47115
2015-10-05 10:26:21 +00:00
John Crispin
1aab21df9f ramips: Allow to receive vlan over untag ports on MT7530
The MT7530 switch driver with enable_vlan set will automatically set all
ports to the user port mode. The hardware will remove the incoming vlan tag
on these ports and use it for its internal vlan. This is usually not wanted
and makes it impossible to communicate via vlan over the switch in both
directions.

It is possible to configure a switch port to "transparent mode" when this
port is only used as untag in the switch VLANs. This will disable the VLAN
untagging of packets when they were received on this port. The tagging on
"tag" ports based on the vlan id is still working.

The transparent port mode cannot be used when a port is both used in a VLAN
as "tag" and in another one as "untag" port.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 47114
2015-10-05 10:26:09 +00:00
John Crispin
dd8f5abb23 ramips: Add build files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
    1: Spaces -> Tabs
    2: Removed some packages

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47113
2015-10-05 10:26:02 +00:00
John Crispin
e6e373d348 ramips: Add DTS files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
  1: Merged most stuff into dtsi file
  2: Remove unnecessary empty lines.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47112
2015-10-05 10:25:53 +00:00
John Crispin
c10bdf11ff ramips: Add base-files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
   1: Fixed model order
   2: Remove manufacturer name from model name
   3: Use a hacky but prettier way to get mac address.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47111
2015-10-05 10:25:47 +00:00
John Crispin
03681684bf ar71xx: Correct WeIO board name
Trivial parch to correct WeIO board name in the system.

Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>

SVN-Revision: 47110
2015-10-05 10:25:40 +00:00
John Crispin
df47e4c55b target/mpc85xx: check if 'generic' subtarget for image file cuImage.tl-wdr4900-v1
Only add 'cuImage.tl-wdr4900-v1' to KERNEL_IMAGES if
the selected subtarget is 'generic'.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>

SVN-Revision: 47109
2015-10-05 10:25:28 +00:00
Rafał Miłecki
07fac13b51 ar71xx: rename firmware for Chinese version of TL-WR941ND v6
It seems there are two *different* versions on TL-WR941ND v6: Chinese
and European one. Currently supported by OpenWrt is Chinese one. Rename
firmware to make it clear.
For details see:
http://wiki.openwrt.org/toh/tp-link/tl-wr941nd
https://forum.openwrt.org/viewtopic.php?id=59295

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47107
2015-10-05 08:54:26 +00:00
Matteo Croce
70da7324cd lantiq: fix binutils 2.15.1 build
SVN-Revision: 47105
2015-10-04 22:03:04 +00:00
Hauke Mehrtens
0cd478518f kernel: update 4.1 to 4.1.10
Fixes a regression on spi flash devices (upstream commit 1583eaece6fa).

Changelogs:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.7
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.8
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.9
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.10

096-ipv4-off-by-one-in-continuation-handling-in-proc-net.patch was applied
upstream and dropped.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>
[update from 4.1.9 to 4.1.10]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47104
2015-10-04 11:34:39 +00:00
John Crispin
7ad419a9f1 ralink: add irq to mt7628 gpio node
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47076
2015-10-01 19:12:14 +00:00
John Crispin
e1b1b0cbfd ralink: the mmc driver can now handle CD lines that are active low
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47074
2015-10-01 18:13:47 +00:00
John Crispin
9e1268b168 ralink: speed selection was broken in spi-mt7621
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47073
2015-10-01 15:35:44 +00:00
Felix Fietkau
2675ade97a uml: backport another upstream patch to fix compile errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47067
2015-09-28 12:22:35 +00:00
Felix Fietkau
82791e92ce uml: fix build with gcc 5
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47062
2015-09-27 17:29:48 +00:00
Felix Fietkau
110a74dd71 uml: update to linux 4.1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47061
2015-09-27 17:29:38 +00:00
Rafał Miłecki
f8a14765b8 brcm47xx: describe 300-fork_cacheflush.patch & 310-no_highpage.patch
These were initially commited in r9285.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47058
2015-09-27 06:53:12 +00:00
Rafał Miłecki
c6c4b2640f brcm47xx: describe 160-kmap_coherent.patch
It was initially commited in r6642.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47057
2015-09-27 06:24:33 +00:00
Rafał Miłecki
6eadb62f70 brcm47xx: describe 610-pci_ide_fix.patch
It was initially commited in r20924.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47056
2015-09-27 06:05:53 +00:00
Rafał Miłecki
c6401c6d61 bcm53xx: add early support for Linksys EA6300 V1
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47052
2015-09-26 22:57:33 +00:00
Rafał Miłecki
792f31bd10 kernel: crypto: fix ubsec_ssb.c compilation with 4.0+
SSB_DEVTABLE_END was removed in 4.0 by upstream commit 673e2baaa6d9
("treewide: Remove unnecessary SSB_DEVTABLE_END macro").

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47047
2015-09-25 04:22:13 +00:00
Felix Fietkau
941505c94b kernel: backport some SPI layer improvements from 4.1 to 3.18, significantly improves flash speed on ramips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47045
2015-09-24 16:07:10 +00:00
Rafał Miłecki
ff6ae7ce34 kernel: remove old "rootfs" splitter
A year ago I made this old splitter obsolete (see r42828), it's time to
completely remove it now. For all this time we got these warnings:
"Dedicated partitioner didn't create "rootfs_data" partition, please fill a bug report!"
and
"Support for built-in "rootfs_data" splitter will be removed, please use CONFIG_MTD_SPLIT_SQUASHFS_ROOT"
but I'm not aware of any bug reports related to that.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47040
2015-09-24 11:19:12 +00:00
Rafał Miłecki
ce7f25066b oxnas: add platform_pre_upgrade for sysupgrade
We're in process of cleaning nand_do_platform_check. Currently it leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.

The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.

This follows all other targets making it finally possible to change
nand_do_platform_check.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47039
2015-09-24 09:18:59 +00:00
Rafał Miłecki
a25fbb5c9a oxnas: drop some unused sysupgrade code
First of all platform_do_upgrade_phase2 doesn't seem to be defined
anywhere. Other than that platform_do_upgrade is not likely to be ever
called. There is a call to nand_do_platform_check which triggers
nand_upgrade_stage1 call with "exit 0" in it.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47038
2015-09-24 09:18:47 +00:00
Felix Fietkau
896d3e3e13 ar71xx: Add WeIO Board Support
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.

Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]

SVN-Revision: 47036
2015-09-24 09:08:47 +00:00
Felix Fietkau
5119ee9be6 ar71xx: fix bogus hardcoded kernel image size for Seama images (fixes #20585)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47034
2015-09-24 08:37:50 +00:00
Felix Fietkau
1061f93476 imx6: disable ext2/ext3 filesystem support (ext4 is enough)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47032
2015-09-24 08:37:35 +00:00
Felix Fietkau
c8f0290651 uml: disable ext2/ext3 filesystem support (ext4 is enough)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47031
2015-09-24 08:37:30 +00:00
Felix Fietkau
67aa83442e arm64: disable ext2/ext3 filesystem support (ext4 is enough)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47030
2015-09-24 08:37:23 +00:00
Jo-Philipp Wich
74f4f519e5 mxs: fixup permissions of image generation scripts
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47029
2015-09-23 18:40:42 +00:00
Felix Fietkau
b0f48b6ebc kernel: add a patch to fix crashes on pppoe disconnect/reconnect
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47026
2015-09-22 11:28:28 +00:00
Zoltan Herpai
ce59fe6b3d mxs: re-work SD card image generation
- Duckbill uses a different partitioning approach than standard
  FSL and Olimex
- use new sdimage to integrate U-Boot into the SD card images

Signed-off-by: Michael Heimpold <mhei@heimpold.de>

SVN-Revision: 47021
2015-09-21 21:10:43 +00:00
Zoltan Herpai
e4eb8a4145 mxs: adopt SD card generation to fixed U-Boot path
Signed-off-by: Michael Heimpold <mhei@heimpold.de>

SVN-Revision: 47019
2015-09-21 21:05:16 +00:00
Felix Fietkau
3babd37b0e omap: add Kernel 4.1
tested on Beagleboard C4

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 47013
2015-09-21 17:40:52 +00:00
Felix Fietkau
c429250ee4 arm64: switch to Kernel 4.1
- fix Kernel dts subdir location
- enable virtio networking
  we are using -M virt which supports virtio devices

changes in symbols due to make kernel_oldconfig:

- CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y : removed
fix security: upstream id: d1fd836dcf00d2028c700c7e44d2c23404062c90

- CONFIG_ARM64_CPU_SUSPEND: removed
commit id: af3cfdbf56b91785650f54e7c9a899d814b4b9fb

- CONFIG_ARM64_PGTABLE_LEVELS=3 : renamed PGTABLE_LEVELS
commit id: 9f25e6ad58e1fb3b4d441e4c55635c4598a6fa94

- CONFIG_GENERIC_CLOCKEVENTS_BUILD=y : removed upstream
commit id: 9f083b74df3a7eaa100b456f2dc195512daf728e

-# CONFIG_PREEMPT_RCU: unnecessary

unknown remove reasons:
-CONFIG_GENERIC_IOMAP=y
-# CONFIG_POWER_RESET_GPIO is not set
-# CONFIG_POWER_RESET_GPIO_RESTART is not set
-# CONFIG_POWER_RESET_LTC2952 is not set
-# CONFIG_POWER_RESET_SYSCON is not set
-# CONFIG_XEN is not set

tested and boot, networking work with qemu

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 47005
2015-09-18 13:39:55 +00:00
Felix Fietkau
708c58c1a7 kernel: fix dependencies of the sock_diag debloat patch (#20544)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46997
2015-09-18 09:05:01 +00:00
Felix Fietkau
6c018c2f5e kernel: solos-pci: Increase headroom on received packets
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46993
2015-09-17 15:38:58 +00:00
Felix Fietkau
312908ff4b kernel: ipv6: ip6_fragment: fix headroom tests and skb leak
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46992
2015-09-17 15:38:46 +00:00
Felix Fietkau
d6408aa9b4 x86/geode: enable DMI and Geos support (fixes #20512)
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

SVN-Revision: 46986
2015-09-17 10:15:52 +00:00
Felix Fietkau
ef447c9a5f x86: fix Geode LX timekeeping (#20531)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46985
2015-09-17 10:15:45 +00:00
Felix Fietkau
45b52d4581 kernel: remove lantiq specific ATM API hacks and their kernel space users (fixes #20523)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46984
2015-09-17 09:45:34 +00:00
John Crispin
9412c4e66c kernel: unbreak atm ABI for 4.0 and 4.1
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46983
2015-09-16 12:40:40 +00:00
John Crispin
e11479771d kernel: properly guard the lantiq atm abi hack with an ifdef
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46981
2015-09-16 12:08:05 +00:00
John Crispin
94295b80ff kernel 3.18/kernel 4.0/kernel 4.1: add missing symbol
deactivate NET_SCTPPROBE just like NET_TCPPROBE

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 46974
2015-09-16 08:33:25 +00:00
John Crispin
74bbc08651 x86: add missing symbol
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 46973
2015-09-16 08:33:18 +00:00
John Crispin
ac75fc8d98 ar71xx: add support for ap152 reference board
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46972
2015-09-16 08:33:14 +00:00
John Crispin
f6607a4bec ath79: dev-eth: fix QCA9561 set phy interface mode and mask
QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different
is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they
have the same device ID(0x1150). So they share the same codes.

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46971
2015-09-16 08:33:04 +00:00
John Crispin
fa09d76521 ar71xx: uci-defaults: fix ap143 to appropriate group
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46970
2015-09-16 08:32:56 +00:00
John Crispin
f461ffbaad kernel: unbreak the atm abi
the lantiq dsl hack to struct atm_trafprm broke the ABI fix this by moving
the variables to the end of the struct

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46964
2015-09-16 08:32:01 +00:00
John Crispin
f453508b3e ramips: Fix pinmux functions for MT7621
The pinctrl-rt2880 code doesn't support multiple functions with the same
name. This will result in a incorrect pinmux configuration.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46963
2015-09-16 08:31:52 +00:00
John Crispin
1297679f4b ar71xx: Add UBNT airGateway Pro support
This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro.

Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com>

SVN-Revision: 46961
2015-09-16 08:31:40 +00:00
John Crispin
3a149a2910 ramips: add mt7621/3/8 support to the I2C driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46959
2015-09-16 08:31:15 +00:00
John Crispin
e6a9d5edf2 ramips: fix reported vendor name
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46958
2015-09-16 08:31:10 +00:00
John Crispin
86a1e46b63 ramips: add proper mt7688 detection
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46957
2015-09-16 08:31:00 +00:00
John Crispin
85d5b9984d ramips: add speed and mode settings to spi-mt7621
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46956
2015-09-16 08:30:43 +00:00
John Crispin
38c28154bd ramips: add get_direction() callback and irq support to gpio-mt7621
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46955
2015-09-16 08:30:17 +00:00
John Crispin
23d79b60ce ramips: more m7628 pinmux fixes
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46954
2015-09-16 08:30:06 +00:00
John Crispin
9473837653 ramips: add mt7628 pwm driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46953
2015-09-16 08:29:55 +00:00
John Crispin
9dfe1f6fbe ramips: make pinctrl work on newer socs
newer socs have 2 mux registers

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46952
2015-09-16 08:29:45 +00:00
John Crispin
710520d5c7 ramips: make the mt7628 spi driver work for both cs lines
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46951
2015-09-16 08:29:40 +00:00
John Crispin
6f07b8a659 ramips: make the early_printk code detect which uart is used
only tested on mt7628

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46950
2015-09-16 08:29:31 +00:00
Felix Fietkau
f74116e599 omap24xx: remove obsolete kernel 3.3 patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46947
2015-09-16 07:56:33 +00:00
Rafał Miłecki
ffcb268437 ipq806x: add platform_pre_upgrade for sysupgrade
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.

The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.

This follows ar71xx, lantiq and partially bcm53xx.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46945
2015-09-15 16:05:10 +00:00
Rafał Miłecki
39940fac6b imx6: add platform_pre_upgrade for sysupgrade
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.

The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.

This follows ar71xx, lantiq and partially bcm53xx.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46944
2015-09-15 16:05:03 +00:00
Rafał Miłecki
90e1b84f15 lantiq: update list on NAND devices in platform_pre_upgrade
Meanwhile BTHOMEHUBV5A board was added.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46941
2015-09-15 11:49:33 +00:00
John Crispin
57c8708d64 lantiq: add platform_pre_upgrade for sysupgrade
As explained in recent sysupgrade/nand.sh commits, current NAND
sysupgrade is a bit misleading because of nand_do_platform_check
behavior. It leaves a special mark in /tmp/sysupgrade-nand-path
triggering some diffent code path in nand_upgrade_stage1.

The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.

Please note that because of current nand_upgrade_stage1 implementation
this patch doesn't change any behaior yet. It only prepares lantiq
target for changing nand_do_platform_check (it will be possible after
preparing all other targets as well).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46939
2015-09-15 06:13:07 +00:00
John Crispin
0dbced8a48 ar71xx: add TP-LINK TL-WDR3320 v2 support
This patch adds support for TP-LINK TL-WDR3320 v2.

This router uses a chinese version 2 firmware header,.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 46934
2015-09-14 20:12:16 +00:00
John Crispin
bfeae90850 ar71xx: extract ath10k wifi board.bin for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46933
2015-09-14 20:12:00 +00:00
John Crispin
fec6313b62 ar71xx: create profile and build image for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46932
2015-09-14 20:11:51 +00:00
John Crispin
b9b6d34e36 ar71xx: enable sysupgrade for the OpenMesh MR1750
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46929
2015-09-14 20:11:24 +00:00
John Crispin
cbf71651ec ar71xx: add user-space support for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46927
2015-09-14 20:11:01 +00:00
John Crispin
aba20334a4 ar71xx: add kernel support for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46926
2015-09-14 20:10:43 +00:00
John Crispin
f582a93a6a realview: create sd card image for qemu
enables a real rootfs with custom size

use qemu with:
qemu-system-arm -M realview-pbx-a9 \
-kernel openwrt-realview-vmlinux.elf \
-nographic -m 1024M \
-sd openwrt-realview-sdcard.img \
--append "console=ttyAMA0 root=/dev/mmcblk0p1"

modified script from brcm2708 target

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 46924
2015-09-14 20:10:04 +00:00
John Crispin
edb5ec3f34 realview: enable sd card support
qemu can be run with -sd <imagename>

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 46923
2015-09-14 20:09:56 +00:00
John Crispin
d1587fb4aa ar71xx: assign proper GPIO pin for Ubiquiti Nanostation models
The GPIO pins for "POE passthrough" of Ubiquiti Nanostation models are the
following:
* Ubiquiti Nanostation M XM: Pin 8
* Ubiquiti Nanostation M XW: Pin 2

The previous definition of the pins was mixed up between XM and XW model.

Signed-off-by: Lars Kruse <lists@sumpfralle.de>

SVN-Revision: 46922
2015-09-14 20:09:40 +00:00
John Crispin
57c5910535 ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.

Signed-off-by: Tobias Welz <tw@wiznet.eu>

SVN-Revision: 46921
2015-09-14 20:09:31 +00:00
John Crispin
2efdc7c896 ramips: add support for Planex DB-WRT01
This patch add support for Planex DB-WRT01. DANBOARD route on
 the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
 DANBOARD is Cartoon character.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46918
2015-09-14 20:08:55 +00:00
John Crispin
06a180d027 lantiq: get more status information from xDSL
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Helge Mader <hmader@tdt.de>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andre Heider <a.heider@gmail.com>

SVN-Revision: 46917
2015-09-14 20:08:39 +00:00
John Crispin
404b183aa8 lantiq: Add AR9 compatibility bits to DWC2 driver
Add AR9 DTS definition to be recognized by the DWC2 driver.

The same driver parameters can be mostly used except that some boards
seem to erroneously report OTG HNP/SRP capability of the USB HCD.
Forcing the HNP/SRP off allows these boards to work with the DWC2 as well.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>

SVN-Revision: 46915
2015-09-14 20:08:15 +00:00
John Crispin
4595440215 lantiq: Introduce DWC2 compatible DTS definitions for AR9 USB
Since the AR9 USB is very similar to the VR9 USB it too can be used with
the upstream DWC2 driver.

Here are the DTS definitions which make it compatible with the DWC2
driver.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>

SVN-Revision: 46914
2015-09-14 20:08:07 +00:00
John Crispin
1f4124ceb0 lantiq: Initialize USB on AR9 platform
Based on the ltq-hcd driver the AR9 USB can be initialized the same way
as the VR9 platform. Use the same initialization bits for both
platforms.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>

SVN-Revision: 46913
2015-09-14 20:07:23 +00:00
Jo-Philipp Wich
fb3fb9b6c1 imagebuilder: store package lists in cache directory
Force opkg to store the downloaded repository indizes into the cache
directory as well, this way the IB can be used in an offline setting
once all required files have been cached.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 46912
2015-09-14 16:57:03 +00:00
Felix Fietkau
fcee359813 ramips: fix chunked-io support for big flash chips (#20504)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46904
2015-09-14 06:54:15 +00:00
Hauke Mehrtens
e1ec8b76e9 ar71xx: fix build of lzma-loader with binutils 2.25.1
To make the lzma-loader build with binutils 2.25.1 it is needed to
remove the .MIPS.abiflags section otherwise I get the following compile
error:

mips-openwrt-linux-musl-objcopy -O binary -R .reginfo -R .note -R .comment -R .mdebug -S loader loader.bin
mips-openwrt-linux-musl-objcopy: Warning: Writing section `.text' to huge (ie negative) file offset 0xffffffff80a00000.
mips-openwrt-linux-musl-objcopy:loader.bin[.text]: File truncated

This should close #20487.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46893
2015-09-12 18:57:37 +00:00
Hauke Mehrtens
41f9b5e42e bcm53xx: add NAND flash chip description for Asus RT-AC87U
This should fix #20492.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46892
2015-09-12 11:10:34 +00:00
Felix Fietkau
1956cc7018 ramips: enable external amplifier for Xiaomi MiWiFi Mini
Attempt to boost the 2.4 GHz signal, currently very low.

Signed-off-by: D. Andrei Măceș <dmaces@nd.edu>

SVN-Revision: 46891
2015-09-12 10:22:41 +00:00
Rafał Miłecki
450aebcdce bcm53xx: reorder some arch patches
This moves arch patches affecting many DTS files. Thanks to this change
we can put some ready-to-mainline patches at 300-319 and simplify
backporting process.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46889
2015-09-11 22:36:05 +00:00
Hauke Mehrtens
89ce027c08 kernel: add CONFIG_MIPS_CDMM config option
This driver was added in kernel 4.1.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46881
2015-09-11 20:31:32 +00:00
Rafał Miłecki
c6e30d6d7a brcm47xx: detect Netgear R6300 V1 & support reset button
It's still far from complete support.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46880
2015-09-11 20:00:02 +00:00
Hauke Mehrtens
4b1278e43e kernel: Added missing symbols into 4.1 & 4.0 kernel default .config
As requested here #20432 I've
tried to fix the missing symbols from the specified default kernel
config files.
I ran into this problem trying to build an image for x86_64 target
with a custom kernel configuration.

Signed-off-by: Manganini Mirko <mmanganini@gmail.com>

SVN-Revision: 46879
2015-09-11 19:02:53 +00:00
Hauke Mehrtens
5b04888848 brcm47xx: update to kernel 4.1
This makes bcm53xx use kernel 4.1 by default now.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46878
2015-09-11 18:52:42 +00:00
Hauke Mehrtens
b075d5e734 bcm53xx: update to kernel 4.1
This makes bcm53xx use kernel 4.1 by default now.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46877
2015-09-11 18:52:18 +00:00
Hauke Mehrtens
5caee877dc brcm47xx: increase max image size
the trx utile uses a maximum image size of 7.2MB. There are brcm47xx
devices even with serial flash with bigger flash chips, but OpenWrt was
not able to create images for these devices. This patch provides an
additional parameter which increases this limit to 32 MB. There is a
warning in the trx utile code which suggests that bigger images could
overwrite the nvram partition on some devices, but normally the program
writing the image should make sure that it is safe to write it to the
flash.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46872
2015-09-11 17:55:28 +00:00
Hauke Mehrtens
c9bebfb9ce brcm47xx: break long lines in image Makefile
This patch changes nothing on the behaviour, it just breaks long lines
with bin/trx to make it easier to add additional parameters.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46871
2015-09-11 17:54:55 +00:00
Felix Fietkau
e1f0a7e841 brcm2708: remove linux 3.18 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46870
2015-09-11 17:17:30 +00:00
Felix Fietkau
6c1adb3eec lantiq: Use the BAR0 base address in the ath PCI fixup code
Fixes support for AR9287 on TP-Link TD-W8980 and possibly other devices
which have an ath wifi chip at a PCI address other than 0xb8000000
(TD-W8980 for example has it's wifi chip at 0xbc000000).

Signed-off-by: Geoffrey McRae <geoff@spacevs.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46869
2015-09-11 16:35:46 +00:00
Felix Fietkau
18c01061a9 mvsw61xx: match swconfig function names
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 46865
2015-09-11 16:34:49 +00:00
Felix Fietkau
b75d188b21 mvsw61xx: use standard swconfig get_port_link
The previous "link" and "status" functions were non-standard,
and thus less useful for parsing.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 46864
2015-09-11 16:34:35 +00:00
Felix Fietkau
542ee6ed19 ar71xx: Restore buildability of the AP121 target
Increase space for kernel and also introduce a 8M flash target into the
Makefile.

Signed-off-by: Attila Lendvai <attila@lendvai.name>

SVN-Revision: 46862
2015-09-11 16:34:08 +00:00
Felix Fietkau
e6fb730daa yaffs2: remove __TIME__ __DATE__ macros
prevent compiler errors with gcc 4.9
increase reproducibility

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 46858
2015-09-11 16:33:12 +00:00
Felix Fietkau
d9857f5468 ramips: Enable RTC support for PBR-M1
The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The
PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself
will not be build because CONFIG_RTC_CLASS is currently not enabled for its
kernel.

Enabling this option should fix the problem of the missing rtc device on
these boards.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46857
2015-09-11 16:32:58 +00:00
Felix Fietkau
bc4f2c5ce4 ar71xx: fix ar724x clock calculation
According to the AR7242 datasheet section 2.8, AR724X CPUs use a 40MHz
input clock as the REF_CLK instead of 5MHz.

The correct CPU PLL calculation procedure is as follows:
CPU_PLL = (DIV * REF_CLK) / REF_DIV / 2.

This patch is compatible with the current calculation procedure with default
DIV and REF_DIV values.

Test on both AR7240, AR7241 and AR7242.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 46856
2015-09-11 16:32:45 +00:00
Felix Fietkau
b1be597a7a brcm2708: add kmod-sound-soc-raspidac3
This adds support for RaspiDAC Rev.3x

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 46854
2015-09-11 16:32:15 +00:00
Felix Fietkau
0b5d87fd30 brcm2708: update 4.1 patches
As usual, this patches were taken (and rebased) from
https://github.com/raspberrypi/linux/commits/rpi-4.1.y

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 46853
2015-09-11 16:32:00 +00:00
Felix Fietkau
2ce833060a target: ar71xx: add support for COMFAST CF-E316N v2 board
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 46852
2015-09-11 16:31:35 +00:00
Felix Fietkau
add0c00c96 imagebuilder: run build prereq checks before building image to set up host commands properly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46840
2015-09-10 11:06:42 +00:00
Jonas Gorski
82fb27917b ipq806x: fix uninitialized variable usage in cpufreq-krait
In krait_cpufreq_probe, both freq and max_cpu_freq are never
initialized, so the max_cpu_freq will have a random value at the end.
Fix this by properly initializing max_cpu_freq to 0 and storing the clk
frequency in freq as well, to make it similar to how it's calculated in
krait_set_target.

Fixes the following warnings:

In file included from include/linux/clk.h:16:0,
                 from drivers/cpufreq/cpufreq-krait.c:13:
drivers/cpufreq/cpufreq-krait.c: In function 'krait_cpufreq_probe':
include/linux/kernel.h:714:24: warning: 'freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
  _max1 > _max2 ? _max1 : _max2; })
                        ^
drivers/cpufreq/cpufreq-krait.c:217:25: note: 'freq' was declared here
  unsigned long freq_Hz, freq, max_cpu_freq;
                         ^
In file included from include/linux/clk.h:16:0,
                 from drivers/cpufreq/cpufreq-krait.c:13:
include/linux/kernel.h:714:24: warning: 'max_cpu_freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
  _max1 > _max2 ? _max1 : _max2; })
                        ^
drivers/cpufreq/cpufreq-krait.c:217:31: note: 'max_cpu_freq' was declared here
  unsigned long freq_Hz, freq, max_cpu_freq;

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46839
2015-09-10 10:09:42 +00:00
Jonas Gorski
bebff6364d ipq806x: modules: fix typo in usb-dwc3-qcom dependencies
The phy driver has its qcom-dwc3 order switched in contrast to the usb
controller driver.

Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46838
2015-09-10 10:09:36 +00:00
Jonas Gorski
a752ff1f8e ipq806x: fix R7500 kernel generation
Obviously the dummy rootfs must be after the kernel (uImage), not
included in it.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46837
2015-09-10 10:09:26 +00:00
Felix Fietkau
5fcafa319d generic: Fix per interface nf_call_iptables setting
commit r30917 ("kernel: bypass all netfilter hooks if the sysctls for that
functionality have been disabled - eliminates the overhead of enabling
CONFIG_BRIDGE_NETFILTER in the kernel config") introduced an optimization
which should reduce/eliminate the overhead for traffic send over bridges on
kernels compiled with CONFIG_BRIDGE_NETFILTER=y. But this optimization
breaks the nf_call_iptables per bridge setting which is more fine grained
than the global sysctl net.bridge.bridge-nf-call-iptables setting.

A test reflecting a real world setup was created to identify if this really
eliminates the overhead and if per-bridge nf_call_iptables could be used in
some setups to increase the throughput. A Qualcomm Atheros QCA9558 based
system with one ethernet and an ath9k wifi 3x3 in HT40 mode was used.
Cables from the AP to the wifi station were used to reduce interference
problems during the tests.

The wlan interface was put in one bridge interface called br-wlan. This
bridge usually contains some more wlan interfaces. The eth0 was put in a
second bridge called br-lan. This usually contains some other privileged
wlan or mesh interfaces. Routing was added between br-lan and br-wlan.

Three kernels were tested:

 * (default) OpenWrt kernel for this device
 * (brfilter-global) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y
 * (brfilter-local)  OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y and
    without 644-bridge_optimize_netfilter_hooks.patch

The changes to the the netfilter settings of the bridge were done via:

 * (brfilter-global) /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=1
 * (brfilter-lobal) echo 1 > /sys/class/net/br-lan/bridge/nf_call_iptables
   and/or echo 1 > /sys/class/net/br-wan/bridge/nf_call_iptables

A station connected to the wlan0 (AP) interface was used to send traffic to
a PC connected via ethernet. iperf with 3 concurrent transmissions was used
to generate the traffic.

| kernel          | br-nf-* global | nf-call* iface | download | upload   |
|-----------------|----------------|----------------|----------|----------|
| default         | 0              | -              |      209 |      268 |
| brfilter-global | 0              | -              |      185 |      243 |
| brfilter-local  | 0              | -              |      187 |      243 |
| brfilter-local  | 0              | br-lan         |      157 |      226 |
| brfilter-local  | 0              | br-lan br-wlan |      139 |      161 |
| brfilter-global | 1              | -              |      136 |      162 |

Download/upload results in Mibit/s

It can be seen that the patch doesn't eliminate the overhead. It can also
be seen that the throughput of brfilter-global and brfilter-local with
disabled filtering is the roughly the same. Also the throughput for
brfilter-global and brfilter-local for enabled filtering on all bridges is
roughly the same.

But also the brfilter-local throughput is higher when only br-lan requires
the filtering. This setting would not be possible with
644-bridge_optimize_netfilter_hooks.patch applied and thus can only be
compared with brfilter-global and filtering enabled for all interfaces.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46835
2015-09-09 18:40:15 +00:00
Rafał Miłecki
f0c747dee5 kernel: describe bridge patch "multicast to unicast"
It was initially added in r41367 by nbd.

SVN-Revision: 46828
2015-09-08 16:43:32 +00:00
Rafał Miłecki
b8c9d6b296 kernel: describe bridge patch "optimize netfilter hooks"
It was initially added in r30917 by nbd.

SVN-Revision: 46827
2015-09-08 16:43:21 +00:00
Rafał Miłecki
255d7ad8ba kernel: describe bridge patch "remove IPv6 depependency of bridge in 2.6.38+"
It was initially added in r27237 by jow as patch from Jonas.

SVN-Revision: 46826
2015-09-08 16:43:10 +00:00
Rafał Miłecki
f8a689d276 kernel: describe bridge patch "port isolate"
It was initially added in r25762 by nbd.

SVN-Revision: 46825
2015-09-08 16:43:04 +00:00
Rafał Miłecki
e77fae4cba kernel: describe bridge patch "always accept EAP"
It was initially added in r26015 by nbd.

SVN-Revision: 46824
2015-09-08 16:42:58 +00:00
Rafał Miłecki
c64214d465 kernel: describe bridge patch "no EAP forward"
It was initially added in r25095 by nbd.

SVN-Revision: 46823
2015-09-08 16:42:50 +00:00
Felix Fietkau
75744d133d kernel: restore 640-bridge_no_eap_forward.patch to its original form
It was corrupted in r38528. The most obvious symptom is repeated messages like this:

Tue Sep  8 08:25:18 2015 kern.warn kernel: [77141.972226] br-lan: received packet on wlan0 with own address as source address

Signed-off-by: Dmitry Ivanov <dima@ubnt.com>

SVN-Revision: 46821
2015-09-08 14:29:55 +00:00
Felix Fietkau
e29efa2fb7 kernel: remove packaging of kmod-crypto-core and kmod-crypto-arc4
Everything except for blkcipher was already built-in, so make blkcipher
built-in as well.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46820
2015-09-08 12:31:04 +00:00
Rafał Miłecki
bda4c3d5e5 brcm47xx: apply serial flash size trick to Netgear WNR1000 V3
It also uses different block size just like WGR614 V10.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46810
2015-09-08 05:24:57 +00:00
Rafał Miłecki
d2a9c35af0 brcm47xx: fix reading WGT634U CFE variables with 4.1
This ports fix from r46584 to the 4.1.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46806
2015-09-07 16:43:29 +00:00
Rafał Miłecki
da2178eb7e brcm47xx: add Netgear WNR1000 V3 support in the Linux arch code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46805
2015-09-07 16:29:21 +00:00
Jonas Gorski
8b4df1efd5 ipq806x: add support for Netgear Nighthawk X4 R7500
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.

Known issues:
 * 5 GHz wifi not working - there is no quantenna driver
 * One of the USB ports is not working

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46796
2015-09-04 14:46:06 +00:00
Jonas Gorski
6ec4c4b6b9 ipq806x: enable ide led trigger
To use gpio leds as ide leds, we need to enable the trigger to be
included in the kernel.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46795
2015-09-04 14:45:49 +00:00
Jonas Gorski
05e4d736d1 ipq806x: add support for retrieving macs from mtd
Add support for mtd-mac-address for stmac.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46793
2015-09-04 14:45:40 +00:00
Jonas Gorski
b958c12d2c image: move netgear-image to top and rename to -dni
Use the same naming as netgear-chk.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46791
2015-09-04 14:45:09 +00:00
Jonas Gorski
156a25b9c4 ar71xx: rename NETGEAR_ variables to their netgear names
Netgear names them BOARD_ID and HW_ID, so we should do the same.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46790
2015-09-04 14:45:04 +00:00
Jonas Gorski
89815d4645 ipq806x: build images and add sysupgrade support for AP148
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46789
2015-09-04 14:45:00 +00:00
Jonas Gorski
e3f6876623 ipq806x: clear IMAGES for devices
Ensure that IMAGE-less devices won't keep the IMAGES of any previous
devices.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46788
2015-09-04 14:44:51 +00:00
Jonas Gorski
7a962fb55a ipq806x: wrap legacy image in uImage
Wrap the zImage in a uImage header so we can easily boot it from legacy
u-boots.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46787
2015-09-04 14:44:48 +00:00
Jonas Gorski
5686d67d1c ipq806x: rename "rootfs" to "ubi" on nand
OpenWrt expects the ubi paritition to be named "ubi", not "rootfs".

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46786
2015-09-04 14:44:44 +00:00
Jonas Gorski
9f44a347ea ipq806x: enable smem-parser for nand on AP148
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46785
2015-09-04 14:44:36 +00:00
Jonas Gorski
556d483a6f ipq806x: enable ubiblock support
To allow squashfs on ubi, enable ubiblock support in the kernel.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46782
2015-09-04 14:44:04 +00:00
Felix Fietkau
efb08b9602 ar7: fix HIGHMEM_START (#20427)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46773
2015-09-02 16:22:44 +00:00
Jonas Gorski
7d6cff4882 kernel: update 3.18 to 3.18.21
Changelog:
 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.21

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46768
2015-09-02 10:18:15 +00:00
Felix Fietkau
7747092ed1 ramips: fix devicetree corruption with some boot loaders if the caches are not ready at boot
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46766
2015-09-02 09:24:05 +00:00
Felix Fietkau
2416e506f5 kernel: bridge, multicast-to-unicast: fix echoes on STA
Currently, multicast packets from an STA are sent to any according
multicast listener directly through the bridge multicast-to-unicast
feature. Unfortunately, so far this includes the originating STA, too,
resulting in multicast packets being echo'ed back to the originating STA
if it itself is a multicast listener for that group.

This behaviour breaks IPv6 duplicate address detection: An IPv6 Neighbor
Solicitation for IPv6 Duplicate Address Detection is being echo'ed back,
resulting in the host falsely detecting an address collision, which
makes the node unable to claim an IPv6 address and use IPv6 in general.

Mac80211 unfortunately only prevents the echoes for us for multicast
frames. For the multicast frames cast to a unicast destination we'll
need to take care of excluding the originator ourselves.

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>

SVN-Revision: 46765
2015-09-02 09:23:59 +00:00
Jonas Gorski
1bc35a08d1 lantiq: remove dead EASY33016 image recipe
Support for lantiq_svip_be has been removed a while ago, so EASY33016
images weren't buildable anymore. Remove the recipes as well as gzip
compressed kernel support, as EASY33016 was the last user of it.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46760
2015-08-30 12:18:22 +00:00
Jonas Gorski
efb2c403cf ramips: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46759
2015-08-30 12:18:14 +00:00
Jonas Gorski
6920a664e8 malta: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46758
2015-08-30 12:18:05 +00:00
Jonas Gorski
09609b4e44 brcm63xx: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46757
2015-08-30 12:18:00 +00:00
Jonas Gorski
f5601a97a2 brcm47xx: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46756
2015-08-30 12:17:57 +00:00
Jonas Gorski
22d707ecd8 ath25: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46755
2015-08-30 12:17:56 +00:00
Jonas Gorski
900b87e96c adm5120: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46754
2015-08-30 12:17:54 +00:00
Jonas Gorski
5ebd02e8d5 brcm63xx: remove legacy led/button related patches
We register all gpio buttons and leds through DT, so no need to keep
fixes/additions for the platform data based bay.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46753
2015-08-30 12:17:52 +00:00
Jonas Gorski
78f253f9b1 brcm63xx: add Comtrend VR-3026e support
Add support for Comtrend VR-3026e v1.
The device is almost identical to the Comtrend VR-3025un.

Signed-off-by: Martin Tesar <tesarmar@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46752
2015-08-30 12:17:46 +00:00
Rafał Miłecki
a9559efe43 brcm47xx: fix Linksys E1200 V2 image filename
Drop unwanted suffix (copy & paste mistake).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46742
2015-08-29 09:23:19 +00:00
Rafał Miłecki
f87990840d bcm53xx: support sysupgrade with Netgear R7000 original firmware
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46732
2015-08-26 15:21:14 +00:00
Rafał Miłecki
8f77e9f668 bcm53xx: add OpenWrt specific stuff for Netgear R7000
This adds DT things that couldn't be upstreamed yet.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46731
2015-08-26 15:21:07 +00:00
Rafał Miłecki
36a8075d90 bcm53xx: use pending Netgear R7000 patch
It includes support for LEDs and buttons.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46730
2015-08-26 14:51:47 +00:00
Rafał Miłecki
1111782e20 bcm53xx: use backported patches for UART0 and profiling
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46729
2015-08-26 14:39:06 +00:00
Jonas Gorski
05a3cdd71f brcm63xx: fix WAP-5813n default network config
/etc/uci-defaults/02_network had a typo, making it generate the wrong
network config.

Closes #20407.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46727
2015-08-26 13:03:09 +00:00
Jonas Gorski
a486ffacea linux: fix off-by-one in handling in /proc/net/route
Add an upstream fix for /proc/net/route causing missing routes doing
several continued reads from it.

Only 4.1+ is affected.

Closes #20403.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46726
2015-08-26 10:11:41 +00:00
Jonas Gorski
77a70a0716 brcm63xx: enable dual rx/tx spi support for hsspi
should improve flash access times. Should be harmless to gnerally
enable regardless if a flash supporting dual reads is attached. In
doubt, spi-nor will just fall back to serial reads.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46725
2015-08-25 22:04:53 +00:00
Felix Fietkau
ddf8858cea kernel: bridge, multicast-to-unicast: assign src after pskb_may_pull()
A call to pskb_may_pull() might reallocate skb->data. Therefore we
should only assign the src-pointer after any potential reallocations.

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46721
2015-08-25 07:25:20 +00:00
Felix Fietkau
ea9963bb21 Revert "kernel: disable multicast-to-unicast translation for ipv6 neighbor solicitation (#17625)"
This reverts commit a080e8e1943156168913d0353a2e99d1151102aa.

It did not fix the problem but just hid some symptom. The real issue was
that IGMP/MLD report suppression was not considered for the
multicast-to-unicast feature. A recent netifd which isolates IGMP/MLD
reports between STAs by utilizing AP-isolation and bridge-hairpinning
should have fixed this.

It is perfectly fine to apply multicast-to-unicast to IPv6 Neighbor
Solicitations, too (once that feature is configured correctly).

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46720
2015-08-25 07:25:10 +00:00
Jonas Gorski
2d53e22357 kernel: remove already upstream applied patch
Remove 131-MIPS-export-get_c0_perfcount_int.patch which was already applied
in 4.1.6. This fixes the following build error:

arch/mips/ath79/setup.c:217:77: error: redefinition of '__kstrtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:77: note: previous definition of '__kstrtab_get_c0_perfcount_int' was here
arch/mips/ath79/setup.c:217:350: error: redefinition of '__ksymtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:350: note: previous definition of '__ksymtab_get_c0_perfcount_int' was here
scripts/Makefile.build:258: recipe for target 'arch/mips/ath79/setup.o' failed

Reported-by: swalker
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46715
2015-08-23 21:33:57 +00:00
Jonas Gorski
548630d74e adm5120: make patches apply again
Fix patches not applying anymore since r46654.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46714
2015-08-23 19:11:07 +00:00
Jonas Gorski
2d379e796f kernel: update 4.1 to 4.1.6
Changelog:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.6

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46713
2015-08-23 18:06:11 +00:00
Jonas Gorski
2190f090bb mvebu: kirkwood: fix ehci-orion probe if generic-phy isn't enabled
Properly treat -ENOSYS as no PHY, else ehci-orion won't work without
generic phy support.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46711
2015-08-23 13:35:03 +00:00
Jonas Gorski
ecdce239a5 brcm63xx: ensure dummy byte is set for mapped spi flash with fast read
Some CFEs seem to misconfigure the mapped memory flash access with
fast read but without a dummy byte, causing all accesses to be prefixed
with 0xff.
This of course breaks reading out the nvram, so do not just move back to
single i/o accessors, but also ensure that the dummy byte is correctly
set.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46707
2015-08-23 09:35:56 +00:00
Zoltan Herpai
e0d332cdbe sunxi: bump to 4.1
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 46705
2015-08-21 13:23:29 +00:00
Zoltan Herpai
79e1aa2ac3 sunxi: add audio module for 4.1
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 46704
2015-08-21 13:16:11 +00:00
Zoltan Herpai
ed1a7a2deb sunxi: update ahci package list for a couple board profiles
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 46703
2015-08-21 10:16:15 +00:00
Zoltan Herpai
c00198216a sunxi: reorganize kmod-ata-sunxi dependencies
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 46702
2015-08-21 10:08:07 +00:00
Imre Kaloz
87a70e0774 This had been set in r44508 as a workaround for switch problems.
Now that the switch driver can handle two devices with
the same MAC address in separate VLANs we can go back
to using the same address on both interfaces.

This is the Linksys firmware's default behavior.

Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 46700
2015-08-21 08:10:48 +00:00
Imre Kaloz
9cca6c5ad9 Previously, all VLANs (port-based or 802.1q) were sharing a single database in the ATU. This created problems in the case of a system where two ports/devices share a MAC address (e.g. Linksys WRT1900AC eth0/eth1).
This also clears any bootloader-set FDB defaults. This had
caused issues creating port-based VLANs when mappings
overlapped previous VLANs. Packets destined to a port
not in the default port group flooded all ports.

Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC)

Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 46699
2015-08-21 08:09:52 +00:00
Imre Kaloz
f57484c4af mvebu: fix cobra chainmask
Thanks Sebastian for spotting it.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 46697
2015-08-21 08:01:48 +00:00
Zoltan Herpai
f5fcb0b4b8 kernel: add missing symbols for 4.1
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 46696
2015-08-20 23:19:42 +00:00