With this patch the following two patches are backported:
* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down
The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45783
Update kernel sources and refresh some patches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45761
Currently port 6 is shown as up 10MBit/half in LUCI and swconfig.
Reason is that all bits in the port 6 config are zero.
This means that also the aneg flag is not set and in this case
ar8216_read_port_link hardcodes the link to be up.
This is no real problem but a little annoying.
To fix this initialize port 6 with the aneg bit enabled.
This causes ar8216_read_port_link to evaluate the link status bit which is
always zero for port 6 as no PHY is connected to this port.
And it doesn't hurt as port 6 isn't connected to anything on TL-WDR4900.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45749
Fix an upstream regression on 3.18+ that causes rt305x based devices
to hang on boot.
Fixes#19715.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45747
Patches are cherry-picked from linux-next. We're also adding the
corresponding config option to the kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45729
Patch cherry-picked from the following location:
https://chromium-review.googlesource.com/#/c/269931/
Disable the i2c device on gsbi4 and mark gsbi4_h and gsbi4_qup clks as
unused. If they are enabled, clock framework will turn them off at end
of probe. On ipq806x by design gsbi4_qup, gsbi4_h clks and i2c on gsbi4
are meant for RPM usage. So turning them off in kernel is incorrect.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45728
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)
Signed-off-by: Matteo Panella <m.panella@level28.org>
SVN-Revision: 45725
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45718
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45717
There is also a OHCI controller, activate it for USB 1.1 support.
This should close#19601.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45716
Add it to the appropriate places so the power led properly works
and ethernet is properly configured for failsafe.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45709
This patch adds support for the Huawei HG655b.
Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45708
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
patching file net/ipv6/ip6_output.c
Hunk #1 FAILED at 886.
1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
patching file net/ipv6/route.c
Hunk #1 succeeded at 2247 (offset 2 lines).
Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)
This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45705
This device seems to have switch port 7 connected to the CPU:
vlan1ports=1 2 3 5 7*
vlan2ports=0 7u
it should be handled by eth1 and NVRAM seems to confirm that (no
et0macaddr entry, existing et1macaddr & et1phyaddr entries).
One of the remaining ports (4/8?) may be connected to the Quantenna SoC.
Original firmware boot log contains following messages:
(0x00,0x5d)Port 5 States Override: 0xfb
(0x00,0x5f)Port 7 States Override: 0xfb
(0x00,0x0e)Port 8 States Override: 0x0a
(why does it force port 5 state?!)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45692
It has 3 Ethernet interfaces, each of them connected to separated switch
port. Default NVRAM uses switch port 8 as CPU which is connected to the
3rd interface (eth2).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45681
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45676
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.
[ 2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.970000] 2 netgear-fw partitions found on MTD device firmware
[ 2.970000] 0x000000070000-0x000000188440 : "kernel"
[ 2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs"
The patch removes the rather useless warning message.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45669
This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/ (patches 110-111)
We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45663
This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.
It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45662
ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended
on most ARM architectures. This automatically calculate ZRELADDR by
masking PHYS_OFFSET with 0xf8000000.
On IPQ806x though, the first ~20MB of RAM is reserved for the hardware.
In newer bootloader, when DT is used, this is not a problem, we just
reserve this memory in the device tree. But if the bootloader doesn't
have DT support, then ATAGS have to be used. In this case, the ARM
decompressor will position the kernel in this low mem, which will not be
in the RAM section mapped by the bootloader, which means the kernel will
freeze in the middle of the boot process trying to map the memory.
As a work around, this patch allows disabling AUTO_ZRELADDR when
ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders
which don't support device-tree, which is the case on certain early
IPQ806x based designs.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45661
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45658
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties.
v2: set correct DEVICE_PROFILES for all images.
v2: migrate TP-LINK TL-WR710N v2 which was committed after v1.
v2: split very very long line `TARGET_DEVICES +=` into smaller parts
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 45643
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45635
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45634
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45633
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45630
This also changes the MAC address to one of the adresses actually used by the
stock firmware on one of the ethernet interfaces.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45599
INET_LRO deprecated and there are exactly two drivers using it, neither
being included in any of the targets enabling INET_LRO. At the same time
both drivers needing it select it.
So just disable it for everyone.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45584
This was a remnant of an old version.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45583
I still need to test following patch before backporting:
bgmac: leave interrupts disabled as long as there is work to do
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45571
Linux 4.0 was released on 2014-04-12
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45559
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45553
There are some rare devices without NAND, like Netgear EX6200 or
TP-LINK Archer C8.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45545
This is needed as prepare_generic_squashfs generates more data (in our
case 0x40004 B) and it's complex for sysupgrade to extract UBI image out
of TRX.
Signed-off-by: Dan Haab <dhaab@luxul.com>
SVN-Revision: 45541
DB149 is a IPQ8064 based platform. This patch adds the init scripts to
detect it, configure the network accordingly, and generate a flashable
image for it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45537
DB149 is an IPQ806x based development platform. This patch adds the dts
files to support it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45536
Certain IPQ806x based platforms are making use of this PHY. So we'll
enable it so it gets detected as such.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45535
-removed symbol because it should be handled by wpan.mk
-add missing FAKEHARD symbol (this symbol is removed in Kernel 4.0)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45530
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45524
The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared
by the function ath79_setup_ar934x_eth_cfg. Clearing these in the
ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they
rely on the preset value by the bootloader.
Instead another function is introduced which also works on ETH_CFG on AR934x.
It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on
machines which require special settings.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45523
The commit r38948 ("ag71xx: add F1E specific feature bit definitions to AR934X
register file") introduced definitions for some bits in the RDV/RXD part of the
ETH_CFG register of AR934x. These are incomplete because ETH_RXDV_DELAY is
specified as 17:16 and ETH_RXD_DELAY is specified 15:14. The original commit
only specified the lower bits. The upper bits also have to be unset when the
lower bits should only be set.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45522
The tx/rx delay bits in the ETH_XMII_CONTROL register have to be unset when the
enable_rgmii_rx_delay/enable_rgmii_tx_delay will be set in the AT803x PHY.
Othwise the throughput in gigabit mode is heavily reduced.
Signed-off-by: Sven Eckelmann <sven@open-mesh.org>
SVN-Revision: 45521
Profile definitions need to be checked and fixed before this patch can
be applied again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45511
Refresh patches to remove the trailing whitespaces caused by an old
diffutils version on osx.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45506
This should rather be done by passing appropriate platform_data/OF, but
should suffice for now.
Fixes e.g. GbE ports on BCM963268BU_P300.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45505
At least the third rgmii port is available on 63169, so assume all are
available. Simplifies cpu vs. variant handling.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45504
The new building code included the rootfs twice when building tplink initramfs images.
To make it more readable move initramfs into an own build step
Build/mktplinkfw-initramfs.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 45491
The new image size is verified by a running tplink device and checked
against mktplinkfw source code.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 45488
The mips74k subtarget of brcm47xx configures gcc to compile for mips32r2;
however, the generated kernel config for 3.14 and later kernels ends up
with CPU_MIPS32_R1 and CPU_MIPSR1 selected. The generated kernel config
for the 3.10 kernel (Barrier Breaker) properly selected CPU_MIPS32_R2 and
CPU_MIPSR2. Modify the default kernel config for mips74k to explicitly
select CPU_MIPS32_R2 and CPU_MIPSR2.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45469
Open-Mesh OM5P-AN use a AT8035 (F1E) behind one of the ethernet ports. This PHY
requires special flags to work correctly. Otherwise massive packet loss happens
with active POE or when switching the link speed from gigabit ethernet to fast
ethernet. The generic PHY doesn't have support to change these settings.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45439
The OM5P-AN boards are suffering from ethernet packet loss when booting with
some active POE setups or when switching to Fast Ethernet when previously
booted with Gigabit ethernet attached.
The cause of the problem is that the AR8035 PHYs requires special register
settings to work reliably on these boards. Enable the RGMII TX, RX delays and
disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD and RDV
delay in the ETH_CFG register to fix the issue.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45438
it has been non-functional for years and caused numerous memleaks and
crashes for people that tried to enable it.
it has no maintained upstream source, and it does not look like it's
going to be fixed any time soon
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45423
It seems to have few ports connected to CPU (only for CPU sending data?)
as part of "SMP dual core 3 GMAC setup" feature.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45403
On BCM5301X there are two different cases to handle: CPU port 8 vs. any
other one. Support for CPU port 8 was already partially implemented but
it lacked setting some extra bit for 2G speed. It also will need to be
extended to implement "SMP dual core 3 GMAC setup". That's the reason
for handling it in separated code block.
This patch also adds overriding CPU port state for port other than 8. It
requires using recently defined GMII_PORT registers.
It was tested for regressions on BCM53011 revs 2 & 3. It was also
confirmed to fix switch on some internal Broadcom board.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45402
In most cases it allows reverting back to the vendor firmware (as they
usually don't use UBI). If users wants to do that we can't do anything
anyway. Erease counters will be just lost. The only thing we do is warn:
"Flashing firmware without UBI for rootfs. All erase counters will be
lost."
It still requires forcing sysupgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45392
We can now detect that provided firmware contains kernel and UBI image
partitions. Flashing it in a sane way (keeping erase counters) still
needs to be implemented.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45391
With previous version of patch info about need of erasing blocks was
stored once per boot. It was breaking in following scenario:
1) First boot after installation (erasing blocks after 0xdeadc0de)
2) Doing sysupgrade (with ubidetach & ubiformat)
3) Attaching UBI again (it caused all blocks to be erased)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45387
It currently does not seem to make a difference anymore, except by
increasing compressed kernel image size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45385
* properly enclose macro arguments in paranthesis on use
* remove trailing white space
* convert C99 // comments
* add missing blank lines after declaration
* remove braces from single statement blocks
* split lines > 80 chars (except for one)
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45356
Having CONFIG_XZ_DEC_ARMTHUMB enabled breaks squashfs when ARM BCJ
filter was used to create the filesystem (and that's what we do on
all ARM targets). Thus unset CONFIG_XZ_DEC_ARMTHUMB to fix
squashfs on sunxi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45347
kmod-usb-phy-qcom-dwc3 is required to get USB working on ipq806x. It was
missed in previous commit so let's enable it automatically.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45345
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page
This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.
Signed-off-by: 盛凯 <shengkai81@gmail.com>
SVN-Revision: 45331
None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.
SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
SVN-Revision: 45328
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.
Update the RouterBOOT helper code to support the new
format.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45297
First of all this patch was affecting other devices, not just Netgear
WNR834B. E.g. Linksys WRT300N v1 also has boardtype 0x0472.
This was breaking PCI on WRT300N, ssb couldn't detect core working in
hostmode (due to mips_busprobe32 failing).
Secondly this patch should not be needed for years now. From the analyze
of #8861 it seems it was needed just to make devices at slots other than
0 discoverable. Setting cardbus to 0 was simply making ssb allow access
to PCI config for devices other than bridge.
With the upstream commit a6c8462 (ssb: fix cardbus slot in hostmode) we
allow accessing device at slot 1 which should be enough for CardBus.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45293
SCHED_AUTOGROUP was turned on by default which forces the use of
CGROUPS, conflicting with the options we offer from menuconfig, remove
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 45275
Default profile already enables usb2 so we'll do the same for usb3 now
that we have support for it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45262
This change adds DWC3 QCOM USB phys and TCSR drivers. These are
cherry-picked from the following LKML threads:
*dwc3 qcom: https://lkml.org/lkml/2014/9/12/599
*tcsr: https://lkml.org/lkml/2015/2/9/579
We're also adding an additional patch to add the corresponding dev nodes
in the IPQ806x and AP148 dts files.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45261
This change doesn't make USB functional but it does make it selectable
from a configuration perspective.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45259
These missing options have been noticed while enabling the following
configuration options on ipq806x, but they're available in the standard
kernel:
*ARCH_QCOM
*CONFIG_USB_SUPPORT
*CONFIG_USB_DWC3
*CONFIG_MFD_SYSCON
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45256
Options that used to be in target config have been added to the generic
config file, so remove them.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45255
original BeagleBoard has no Ethernet
provide a profile with all available USB Ethernet adapters
EBVBeagle comes with a kmod-usb-net-mcs7830 compatible device
tested with BeagleBoard C4
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45237
- does not compile with 3.18
compile error: 'struct wl12xx_platform_data' has no member named 'gpio'
- different version was sent 2015 but cannot be tested by me
see "[PATCH v7 0/6] wlcore: add device-tree support" series
in linux-omap
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45235
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 45208
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: changes in input.mk broke the patch, some of the CONFIG_SND_*
stuff was added already
SVN-Revision: 45205
Platform device support has been removed from the gpio-74x164
driver in 3.14. Restore that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45203
Enabling this option renames the bootloader supplied root=
and rootfstype= variables, which might have to be know but
would break the automatisms OpenWrt uses.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45196
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit 7e5cf0fa1b694f835cdc184a8395b229fa29f9ae
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Aug 7 11:25:05 2014 +1200
yaffs-direct: Basic tests. Add lpthread flag for background gc support
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45188
Accidentally left over development artifact.
Reported-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45179
KERNEL_IMAGE is used as target rule so reusing the same name causes:
Makefile:326: warning: overriding recipe for target `bin/brcm47xx/vmlinux.lzma'
Makefile:326: warning: ignoring old recipe for target `bin/brcm47xx/vmlinux.lzma'
Makefile:326: warning: overriding recipe for target `build_dir/target-mipsel_74kc+dsp2_uClibc-0.9.33.2/linux-brcm47xx_mips74k/vmlinux.lzma'
Makefile:326: warning: ignoring old recipe for target `build_dir/target-mipsel_74kc+dsp2_uClibc-0.9.33.2/linux-brcm47xx_mips74k/vmlinux.lzma'
Unfortunately this will cause copying vmlinux.lzma over and over like:
cp vmlinux.lzma FOO-kernel.bin
which is redundant on brcm47xx where we never modify kernel image.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45178
This makes sysupgrade reject firmware images for different devices.
Right now only support for 2 sample devices is implemented.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45170
Now that all supported boards have an dts there is no need for a
dtb free kernel anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45169
Appearently the kernel only uses kernel above it, so moving it to an
higher address causes a lot of unavailable memory (#19327).
Also move the on-flash kernel to 0x80a0000, as newer CFEs don't like
uncompressing there (net-booting an ELF kernel is fine, though).
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45164
The setting has been lost during the transition to 3.18.
The CONFIG_M25PXX_PREFER_SMALL_SECTOR_ERASE option is not
available anymore, so use CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45161
There were a few issues with the existing code to detect the model string:
* Always using the string starting with byte 56 would cut off the W of WNDR when
the ID starts with 29763654+16+64 instead of 29763654+16+128
* The string contained garbage after the zero byte instead of cutting it off
after the zero (which wasn't always visible using busybox tools, but could
confuse other scripts)
Tested on a WNDR3700v1 and a WNDR3700v2 using the new 29763654+16+64 ID in the
ART. Furthermore, tested against ART dumps of a WNDR3700v2 using the old
$'\xff...' value and a WNDR3800.
The [ -z "$model" ] check was dropped as there is no way to actually hit this
unless no ART partition is found at all.
The awk command was carefully crafted to work both with gawk and the (horribly
broken) busybox awk.
Fixes#18992.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45140
Update the xburst target to kernel version 3.18 and also remove the broken 3.10 support.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 45031
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Last time i got some mess . This is new version.
Signed-off-by: Jay Weng <fl.service@t-firefly.com>
SVN-Revision: 45018
Should fix pcmcia on BCM6348 and BCM6358 after switching to DT-probed
gpio controllers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44995
Fixes the following issue:
drivers/gpio/gpio-bcm63xx.c: In function 'bcm63xx_gpio_probe':
drivers/gpio/gpio-bcm63xx.c:80:4: error: implicit declaration of function 'devm_kasprintf' [-Werror=implicit-function-declaration]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44986
Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 44985
Currently there isn't images ready for flashing liveboxes boards. This
patch adds a script and the code to call it in the bcm63xx images
builder makefile to generate the livebox 1 firmware.
I removed some lines to avoid generating unneded files in the bin/ dir
for this board. And added code to generate a squashed rootfs aligned to
64 kB since the current one in the /bin dir is 128 kB aligned and
doesn't work. Still no sysupgrade support for this board. Upgrading from
within openwrt can be done writing with mtd the kernel, and then the 64k
aligned rootfs.
Regards
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: use sed instead of a separate shell script for the boot script, make it
respect the load address]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44982
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
This changes the x86 image generation to match x86_64, using the PARTUUID for
the rootfs instead of explicitly configuring the device.
It unbreaks KVM with VirtIO, which uses /dev/vda2 instead of /dev/sda2.
Tested in QEMU/KVM with VirtIO, VirtualBox and VMware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44966
Otherwise the root device won't be found in 1/16 of the generated images
(whenever the signature starts with a zero digit).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44959
It depends on obsolete compilers and only works on one device (an
evaluation board).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44956
also refresh generic patches for 3.14, 3.18, 3.19 and 4.0
targets might need a minor refresh as well, however, it looks
like everything still applies cleanly with occasional small
offsets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44876
There are two versions of the GL.iNet, the 6408A and the 6416A. The only
difference is the flash size.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44860
Ensure gpio chips are always labeled the same; this allows simplifying
any arch setup gpio lookups.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44846
Now that we have converted all users of global variables to use
brcm63xx_board_name, we can savely convert the implicit call to detect
in brcm63xx.sh to a single, explicit call in preinit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44840
r37000 made button kmods loaded from generic code, so we don't use
it anymore for deciding to load them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44838
Instead of setting them up on invocation of brcm63xx_detect, set them
when calling diag.sh based.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44837
Board IDs are not unique, so in preparation for depricating them, always
use board_name for any (default) configuration decisions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44836
Use the device tree model property for detecting the board instead
of board id from nvram if present.
Since we can now directly detect the DVA-G3810BN, we can remove the
extra check for it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44834
Take full board name from devicetree, if present. Provide a method
for retrieving the board name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44833
Rename board_name to board_id to prepare for using board_name as a
proper name for the board.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44832
This adds support for the Netgear DGND3700 v1 and DGND3800B.
DGND3700 v1 and DGND3800B are exactly the same router, only one difference,
the factory firmware. This patch produces two factory firmwares for each router.
The router includes an onboard NAND flash for extra storage. NAND is currently
not supported in bcm63xx, so no code added for this part. The NOR flash (32MB)
is enough for storing an openwrt firmware.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: Add back commit message from v1]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44831
Build all geode platform drivers into the kernel
Remove kmod-* packages for these drivers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44809
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44795
This patch allows AP148 to boot from NOR flash.
As we're using a FIT image as kernel (which includes kernel bin + DTB)
we enable the MTD_SPLIT_FIT_FW kernel option, which will detect the FIT
image and automatically split the "firmware" partition into 2 MTD parts
(kernel + rootfs).
The rootfs will then be parsed and split between rootfs + rootfs_data,
as usual.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44794
Only one bootargs is really needed: the tty port. All the other
information will use the OpenWrt mechanisms.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44793
If this option is enabled, the FIT image format will be detected and
split by the mtdsplit code. Detection is based upon the FDT magic, which
will trigger the parsing and detection of the rootfs, ending-up in the
creation of the 2 new partitions.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44792
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.
The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44791
It will now actually enable the mib counters instead of enabling rx/tx for
the first switch port.
Reported-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44788
copied target/linux/x86/config-3.14 and target/linux/x86/patches-3.14 to
3.18 equivalents and then tweaked until it built.
Tested on alix2, soekris net4826 and soekris net4521.
Still having trouble with net4826 booting from Grub, alix2 and net4521
are fine.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 44758
Move first 3 patches to 0xx numbers range to denote that this is
backported code and they should be removed when we update
kernel to version >= 3.19
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44732
To finally sync code with upsream cleanup registers headers, and update
several comments and kernel config symbols descriptions. No functional
changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44731
Cleanup board patch by moving code to specific patches, and factor out
leds to separate patch. No functional changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44729
Move GPIO patches behind PCI patch, since they are not yet merged
upstream.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44728
Make register names more consistent, mostly add appropriate prefix
(AR5312_ or AR2315_) or _BASE suffix. Also add macro to simplify mask
and shift operation.
No functional changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44726
There are no external users (last one was PCI driver) for these headers,
so move them to arch directory. Few macroses from ar231x.h header moved
to devices.h and file was removed.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44724
Honestly remap main SoC MMR mem and use accessor functions to
interact with registers. Now registers defined relatively to base
address (e.g. SDRAM controller base address).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44723
AFAIK, no one AR2315+ chip (AR2315, AR2316, AR2317, AR2318) does not
contain IR block, so remove IR registers definitions. Also remove few
unused macroses.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44722
Pass PCI IRQ and I/O memory ranges via platform device resources, this
change makes PCI controller driver independed from arch headers, so
also remove few includes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44721
Honestly remap PCI controller MMR and use accessor functions to interact
with registers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44720
Add container and place all context specific variables and structure to
it.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44719
Put AR2315_PCI_HOST_SDRAM_BASEADDR macro to DMA header, since this is
arbitrary value and not some hw specific constant. Also this relocation
decouples dma from HW specific header.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44716
Do not use prom_init() callback, do memory initialization in
plat_mem_setup() callback and move serial port configuration to
arch_initcall stage.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44715
Check SoC family (AR5312+ or AR2315+) before call instead of checking it
inside the called function. Also convert ar{5312,2315}_init_device()
function to void, since they both return zero and nobody care about
return value.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44713
Sync functions, variables and enums names with upstream. Mostly replace
'ar231x_' prefix by 'ath25_'.
No functional changes, except few 'int' -> 'unsigned' changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44712
Ethernet controller driver don't use boarddata directly, so remove
corresponding field from its platform device structure.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44710
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".
There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:
Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.
The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44692
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Signed-off-by: daixj <fl.service@t-firefly.com>
SVN-Revision: 44690
Here the device tree entry for ifxhcd is listed as compatible with one
supported in dwc2 (after patching the dwc driver appropriately).
A second entry is added to support the second core of the hcd. This
entry is listed to be compatible with only dwc2. Done this way there
should be backwards support for both hcd drivers (ltq-hcd and dwc2)
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44676
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big
endian systems such as the mips based SoCs made by Lantiq. Then dwc2
can be used to replace ifx-hcd driver for Lantiq platforms found e.g.
in OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44675
Lantiq driver does not work with autodetected fifo sizes so use ones
from original ltq-hcd driver in dwc2. Other values can be
autodetected.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44674
Port gpio code from original ltq-hcd driver to dwc2.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44673
Add VR9 specific usb initialization bits from ltq-hcd to platform
initialization.
This patch is more of a proof-of-concept than production quality
since the initialization registers are different on other lantiq
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44672
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.
Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44665
By removing the NL16 signature check, the parser can be
utilized by other devices like the WD My Net Wi-fi Range
Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44664
This patch renames the partition parser from
wrt160nl to more generic cybertan.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44663
