This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49076
Not all mach-* files set all boards correctly in ETH_CFG. They depend on
some preset values by u-boot which were not previously modified by
ath79_setup_qca955x_eth_cfg. Avoiding to modify them in this function keeps
it backward compatible for these boards.
This reverts commit 119b8ab2c2eac237ec4e9c4d0ed53df22b5c6978.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49072
The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some
boards. These boards depend on the preset values of u-boot which may
differ.
This reverts commit f2d4bb96b62512caa161dcc2867c91692fb16a38.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49071
The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR1750 can be used instead.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49070
The MR900 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR900 can be used instead.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49069
Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3
and WNR612v2.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49051
The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.
This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.
Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49031
The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.
This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.
Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49030
Some u-boot versions for QCA955x change the delays based on the link speed
during boot. This usually breaks the support of other linkspeeds when
OpenWrt is booted. It also conflicts with the
at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own
values in QCA955X_GMAC_REG_ETH_CFG.
The default RGMII values from the Atheros u-boot are currently used to
preset the existing mach files. These may have to be adjusted for boards
using different values but which are not currently set them explicitely in
OpenWrt.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Christian Beier <cb@shoutrlabs.com>
Cc: Chris R Blake <chrisrblake93@gmail.com>
Cc: Benjamin Berg <benjamin@sipsolutions.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Dirk Neukirchen <dirkneukirchen@web.de>
Cc: Christian Mehlis <christian@m3hlis.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 49029
Some u-boot versions for QCA955x set currently not cleared bits depending
on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c
file is responsible to select the correct configuration bits and thus the
ath79_setup_qca955x_eth_cfg has to clear the unset.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49028
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 48937
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48779
Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48777
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
In r45970 the MAC swap handling was made opt-in, however some boards
have been forgotten during the conversion. Since the reference design
uses this MAC swapping, and pretty much all known boards using this chip
seem to do so too, enabling the swapping is a more reasonable default
than leaving it disabled.
Change the code to still allow boards to opt-out of this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47956
The following patch is to add ath79_register_m25p80_large, which sets
is_flash to false to support bit banging. This is needed on some 32MB+
SPI chips, such as the S25FL256S1
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47952
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47940
Kernel part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47939
Kernel part of support for PowerCloud CAP324 Cloud AP.
The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
the CloudCommand service for 'cloud' based managment of large numbers
access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47938
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47261
This patch fixes ticket #15267 by enabling power on the
WNR2200's USB port. At present, the USB port on the WNR2200
is non-functional due to it not receiving power.
This patch defines an additional GPIO pin, but none of the
current GPIO definitions have been modified.
Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch>
SVN-Revision: 47236
This patch supersedes the v1 from September 17th.
Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.
The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).
Fixed items:
- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.
Compiles fine, has been confirmed working by owners on 15.05.
Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?
Thank you
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 47234
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47221
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]
SVN-Revision: 47036
QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different
is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they
have the same device ID(0x1150). So they share the same codes.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
SVN-Revision: 46971
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.
Fix Ethernet by setting the right values.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 46281
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46206
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46046
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 45954
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45635
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45634
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45633
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45630
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45524
