Commit graph

18278 commits

Author SHA1 Message Date
Sergey Ryazanov
6cad8ee0bd ar71xx: keep the RouterBOARD Power LED in On state
It is quite unexpected behaviour when the Power LED switches off as soon
as the kernel starts booting. So set the default state to 'Keep' for
the Power LEDs of all RouterBOARDs (e.g. RB91x, SXT Lite series, etc.).

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[switch the default state to keep instead of on]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-20 19:10:29 +02:00
Chuanhong Guo
a4c84b2d73 ramips: add support for Phicomm K2P
It uses one MT7615D radio chip with DBDC mode enabled. This mode allows
this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time. However mt76 doesn't  support it currently so there is no
wireless available.

Specification:
- SoC: MediaTek MT7621AT
- Flash: 16 MB
- RAM: 128 MB
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Wireless radio: MT7615D on PCIE0
- UART: 1 x UART on PCB - 57600 8N1

Issue:
- Wireless radio doesn't work due to the lack of driver.

Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2,then follow the instruction to
   set device and tftp server IP address and input the firmware
   file name.U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2017-07-20 19:10:29 +02:00
Andrea Merello
b81c04382b lantiq: fix sleep with spinlock held in xrx200 network driver
In the xrx200_close() function we call napi_disable(), that could
sleep, with priv->hw->chan[i].lock held. This could lead to deadlock
and causes the kernel to complain.

Look at the code I couldn't convince myself about why we
need to protect that specific code part with the lock. IMHO there
seems no reason to protect the refcount variables, because AFAIK
ndo_close() and ndo_open() callbacks are already called with a
semaphore held. Neither I could figure out why napi_disable() have to
be called with that lock held. The only remaining code part for
which I could guess the lock is useful for is ltq_dma_close()
function call.

This patch reduces the lock to the said function call, avoiding the
sleep-with-spinlock-held situation

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
[fold into 0025-NET-MIPS-lantiq-adds-xrx200-net.patch, backport to
kernel 4.4]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-20 19:10:29 +02:00
Florian Fainelli
6bdb662deb uml: Backport upstream fix to build against static libpthread
Backport upstream commit f44f1e7da7c8e3f4575d5d61c4df978496903fcc ("um:
Avoid longjmp/setjmp symbol clashes with libpthread.a") to fix build
issues on hosts that only have a static libpthread.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-07-18 14:52:51 -07:00
Baptiste Jonglez
cd10577350 x86: Fix xen serial console by removing conflicting PATA driver
The Xen serial console has been broken since the xen_domu subtarget
was merged in the generic x86 subtarget (commits 1d6879ee and 371b382a).

The reason for the broken serial console seems to be an IRQ conflict
between the serial console driver and the PATA_LEGACY driver:

[    1.330125] genirq: Flags mismatch irq 8. 00000000 (hvc_console) vs. 00000000 (platform[pata_legacy.4])
[    1.330134] hvc_open: request_irq failed with rc -16.
[    1.330148] Warning: unable to open an initial console.

Just drop the PATA_LEGACY driver from the x86/generic and x86_64
subtargets, since this driver is marked experimental and only supports
very old ISA devices anyway.  It is still included in the x86/legacy
subtarget where it rightfully belongs.

Fixes: FS#787

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2017-07-16 11:31:52 +02:00
Baptiste Jonglez
6548b34c3f x86/64: add xen DomU support
Xen support for x86/generic was added in 1d6879ee.  This commit also
enables it for x86/64.

This was successfully tested with Xen 4.5, although the serial console
is broken in the same way as x86/generic (see FS#787)

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2017-07-16 02:29:05 +02:00
Baptiste Jonglez
de8370fcf2 x86: Move USB support from subtargets to target config
All x86 subtargets enable USB support, so it makes sense to enable it
in the target config instead, to avoid duplication.

Also refresh subtarget configs accordingly.

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2017-07-16 02:29:05 +02:00
Baptiste Jonglez
609f169ff4 x86: Refresh subtargets kernel config
This was done by simply running `make kernel_menuconfig CONFIG_TARGET=subtarget`
and then saving without changing any option.

Most of the removed options can be explained because they are already
present in the target config or in the generic 4.9 config:

- PAE-related options, enabled by default on x86 by 961c0eac
- LZO-related options, enabled by default since 4.9

As far as I understand the build system, this shouldn't have any
user-visible impact, because the build system already merges the
various kernel configs during build.

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2017-07-16 02:29:04 +02:00
Baptiste Jonglez
31ba457416 x86: Drop stray subtarget "epia"
This subtarget was added by 961c0eac, probably by mistake.  It does
not contain anything beside a kernel config.

Acked-by: Daniel Golle <daniel@makrotopia.org>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2017-07-16 02:28:50 +02:00
Mathias Kresin
e4e984f2a0 treewide: use only board_name function to get name
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.

The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
e0b9ec8e96 treewide: drop target board_name functions
They are not used any longer.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
f12a32630f treewide: use the generic board_name function
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
ced05ca9e0 sunix: run b53_hack later
The script relies on the board name but runs prior the generic sysinfo
script which sets the board name.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
78cf5eed6e treewide: do board detection during preinit
Do the board detection during preinit to unify it across all targets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
ac3e05c5d7 treewide: populate boardname and model earlier
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.

Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
John Marrett
4531bc4267 ramips: fix GL-inet GL-MT300N-V2 WAN/LAN MAC address
Correct MAC address lookup to appropriate offset based on vendor
source.

Override the WAN MAC to use the same address as LAN. The switch driver
increments the base MAC address for the WAN vlan but the stock firmware
uses the same MAC address for all interfaces.

Based on vendor source commit
https://github.com/domino-team/lede-1701/commit/efb0518

Signed-off-by: John Marrett <johnf@zioncluster.ca>
2017-07-15 07:02:59 +02:00
Mathias Kresin
f7eb7f577f imx6: fix DualLite/Solo GW551X board detection
The model name is a different one in the device tree source file.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 07:02:59 +02:00
Koen Vandeputte
cd54b2d42b kernel: update kernel 4.9 to 4.9.37
- Refreshed all patches
- Removed upstreamed
- Adapted 4 patches:

473-fix-marvell-phy-initialization-issues.patch
-----------------------------------------------
Removed hunk 5 which got upstreamed

403-net-phy-avoid-setting-unsupported-EEE-advertisments.patch
404-net-phy-restart-phy-autonegotiation-after-EEE-advert.patch
--------------------------------------------------------------
Adapted these 2 RFC patches, merging the delta's from an upstream commit
(see below) which made it before these 2.

https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-
stable.git/commit/?h=v4.9.36&id=97ace183074d306942b903a148aebd5d061758f0

180-usb-xhci-add-support-for-performing-fake-doorbell.patch
-----------------------------------------------------------
- Moved fake_doorbell bitmask due to new item

Compile tested on: cns3xxx, imx6
Run tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-07-15 00:13:05 +02:00
Stijn Tintel
a576ed5437 scripts/gen_image_generic.sh: move from x86/image
The script can also be useful for other targets.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-07-14 04:09:16 +02:00
Alexander Couzens
8c96eb2fdb
ar71xx/image: change unifi UBNT_CHIP to ar7240
Verified by OEM firmware images which contains the same
chip.

Tested-by: Andreas Bräu <ab@andi95.de>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-07-13 23:56:24 +02:00
Matthias Schiffer
16222a1010
ar71xx: set US region code for TP-Link TL-WR710N v1 image
Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so
far, so we can just set US unconditionally.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-12 21:30:08 +02:00
Matthias Schiffer
438dcbfe74
base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.

The list of binaries is also slightly cleaned up and duplicates are
removed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:26:32 +02:00
Matthias Schiffer
f464da623d
kirkwood: upgrade: fix RAMFS_COPY_*
RAMFS_COPY_* are moved to platform.sh toplevel. The nand_do_upgrade call is
moved to platform_do_upgrade.

Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:19:23 +02:00
Matthias Schiffer
08a94ecaee
ipq806x: upgrade: fix RAMFS_COPY_*
RAMFS_COPY_* are moved to platform.sh toplevel. The unneeded
linksys_preupgrade function is removed, and the nand_do_upgrade call is
moved to platform_do_upgrade.

Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:19:23 +02:00
Matthias Schiffer
73f675415c
bcm53xx: upgrade: fix RAMFS_COPY_*
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:19:23 +02:00
Piotr Dymacz
9d07d2dc56 ar71xx: image: simplify Meraki MR16 device definition
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:46:53 +02:00
Enrique Giraldo
afcf5f69be ar71xx: fix upgrade platform check for Compex WPJ558
The magic number was wrong and always marked the images as invalid.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
2017-07-09 23:46:30 +02:00
Piotr Dymacz
befc763ed1 ar71xx: support LED in TP-Link TL-WR902AC RJ45 socket
TP-Link TL-WR902AC has another one, tiny LED inside RJ45 socket which is
attached to GPIO15. Add support for it, use it as a "lan" LED and rename
old one to "internet". Also, fix uci option name for "lan" LED in system
configuration ("wan" -> "lan").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:44:20 +02:00
Piotr Dymacz
42c8bbb69b ar71xx: verify TP-Link TL-WR902AC sysupgrade image
Until we enable requirement for metadata in sysupgrade images under
ar71xx target, this prevents users from using wrong image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:43:46 +02:00
Henryk Heisig
096a604df0 ar71xx: add metadata to some TP-Link images
This commit adds metadata to TP-Link sysupgrade images
created by tplink-safeloader with uImage kernel header.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-07-09 22:45:59 +02:00
Mathias Kresin
01819254af ramips: sound-mt7620: fix dependencies for kernel 4.9
With kernel 4.8 common used code was moved to a shared kmod. Add the
missing dependency to the shared snd-soc-simple-card-utils.ko.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-07 07:56:24 +02:00
Mathias Kresin
1743ed49c1 kernel: add missing symbols
Fixes the ramips and xburst/qi_lb60 build.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-07 07:44:51 +02:00
Mathias Kresin
3dc757856c lantiq: fix typo in EASY80920.dtsi
There is no device tree property named phynmode0. Use phy-mode as it is
done for the other ethernet nodes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-07 07:18:14 +02:00
Thomas Nixon
50e3659703 lantiq: add Netgear DM200 support
Netgear DM200 is an inexpensive VDSL modem:

    CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
    RAM: 64MiB
    Flash: 8MiB
    Ethernet: 1x100M
    DSL: VDSL2+, ADSL2+
    reset button, 3x bi-color LEDs

Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.

To upgrade from the vendor firmware, upload factory.img

The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.

Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.

Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2017-07-07 07:13:24 +02:00
Matthias Schiffer
4b32d66216
ramips: simplify ubnt-erx-sfp device definition
Most of the ubnt-erx definition can be reused; the package removals in
DEVICE_PACKAGES have become redundant after d17cb4a68a "ramips: purge
default packages on MT7621".

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-06 19:45:09 +02:00
Felix Fietkau
7887a46f45 build: enable gzipping of images on x86 even if ext4 is disabled
There is lots of padding between the boot partition and the rootfs, so
gzipping is helpful here

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-07-06 11:30:33 +02:00
Ram Chandra Jangir
c2a4f144d7 ipq806x: Enable AP148 fit image(.itb) generation
This change enables .itb image generation for AP148,
It will help us to boot and test AP148 with NOR flash.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-07-06 07:16:40 +02:00
John Crispin
fddc78bc11 ramips: bump to v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-07-06 06:37:03 +02:00
Jonas Gorski
a0bb6c91fe brcm63xx: remove misleading warning about partial SPI NOR writes
The warning will be triggered by jffs2 or UBI, and partial writes are no
issue for most flash chips.

Fixes: 2a2b16210b ("brcm63xx: backport upstream solution for SPI message size limits")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-07-05 11:24:24 +02:00
Mathias Kresin
0825de2df7 kirkwood: drop kernel 4.4 support
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-04 16:29:07 +02:00
Paul Wassi
9808b9ae02 kirkwood: switch to kernel 4.9
Add patches-4.9, some of them (heavily) rewritten:
  - ea4500 is upstream available, keep only LEDE changes in dts
  - ea3500 is changed to match the structure of the upstream ea4500 dts
  - nsa310s rewritten to include the common dtsi
  - nsa325 is dropped, since already upstream

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[refresh kernel config, add on100, use the switchdev based mv88e6171
driver for the linksys boards, keep lede specific rootfs/kernel
partition names for linksys boards, reorder patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-04 16:29:07 +02:00
Mathias Kresin
08c499f865 lantiq: use img file extension for DGN3500 factory images
The Netgear UI in basic mode refuses the upgrade file if the the
fileextension is not img. The expert/advanced mode accepts any
fileextension. Use img to make it work in any case.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-04 16:29:01 +02:00
Piotr Dymacz
cf23547e57 ar71xx: fix TPLINK_BOARD_ID for Archer C58 and TL-WA855RE
Rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID for two ommited devices.

Fixes: 7d6c63d ("build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 15:09:52 +02:00
Qian Zheng
a08ec9a54d ar71xx: fix Netgear WNDR3700 v4 switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
2017-07-04 11:42:33 +02:00
Piotr Dymacz
6165e4aab0 ar71xx: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

Root access over serial line in vendor firmware: root/sohoadmin.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
0a2e4204db ar71xx: generic: enable CONFIG_MTD_SPLIT_TPLINK_FW
We can use "tplink-fw" mtd splitter for TP-Link devices which use kernel
with TP-Link header embedded inside "safeloader" image type and thus get
rid of statically defined "kernel" and "rootfs" partitions in cmdline.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
43ae7dcdd4 ar71xx: refresh and cleanup mikrotik subtarget kernel config
Refresh mikrotik subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
f67ad17d19 ar71xx: refresh and cleanup nand subtarget kernel config
Refresh nand subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
cc9b9c5885 ar71xx: refresh and cleanup target kernel config
Refresh target kernel config and disable kernel support for all boards
which belong to nand and mikrotik subtargets only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Hauke Mehrtens
1f991bb365 brcm47xx: Add support for kernel 4.9
I tested this on a WRT54GS and a WRT610N V1.
The WRT610N does not boot when the kernel is too big, so I deactivated KALLSYMS

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-07-02 23:10:06 +02:00
Hauke Mehrtens
b56995550a brcm47xx: refresh kernel configuration
Run make kernel_oldconfig on the brcm47xx target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-07-02 22:44:07 +02:00
Hauke Mehrtens
250d305455 brcm47xx: remove kernel 4.1 support
Kernel 4.1 is not supported by LEDE for some time now.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-07-02 22:44:06 +02:00
Mirko Parthey
e3b339e2ea brcm47xx: use DMZ LED as status indicator
On the Linksys WRT54GSv1, the Power LED flickers in the "off" state.
Indicate status using the DMZ LED if available, since it has solid "on" and
"off" states.

This change was tested on the WRT54GSv1, but may also affect other brcm47xx
devices.

Fixes FS#793.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
2017-07-02 22:44:06 +02:00
Mirko Parthey
1dace8cbe0 brcm47xx: resolve GPIO conflict for WRT54GSv1
On the Linksys WRT54GSv1, the adm6996 switch driver and the
gpio_button_hotplug module both claim GPIO 6, which is connected to the
Reset button.  When the switch driver's request wins, the Reset button
cannot work. This makes it impossible to enter failsafe mode without a
serial console.

Stop requesting the "adm_rc" GPIO in the switch driver, since it is not
used anywhere.

Fixes FS#792.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
2017-07-02 22:44:06 +02:00
Jonas Gorski
eaaba94bf6 kernel: add missing symbol to generic
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-30 12:14:10 +02:00
Jonas Gorski
beaaf214f7 brcm63xx: refresh smp config
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-30 12:13:08 +02:00
Jonas Gorski
d131e36e41 brcm63xx: enable KEXEC for SMP again
It seems it compiles again, so there is no reason to keep it disabled.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-30 12:12:38 +02:00
Jonas Gorski
2983576bae brcm63xx: disable commandline parts parser
We don't use it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-30 12:12:32 +02:00
Anthony Sepa
f9b67b89d3 brcm63xx: add support for the Actiontec R1000H gateway
SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0

Known issues:
 - Unable to detect 53115 switch attached to MDIO. Not supported
 - No support for the cable port

More info on the device and the research can be found at:
http://www.actiontec.com/212.html

Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)

Signed-off-by: Anthony Sepa <anthonysepa@yahoo.ca>
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-30 12:12:17 +02:00
Jonas Gorski
1dc7a0cfd5 brcm63xx: fix bcm6328 pinmux other register
The pinmux register is at relative offset 0x8, not 0xc. Fixes hang
when trying to modify pins >= 32.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-30 12:12:06 +02:00
Jo-Philipp Wich
28cb6ed949 ar71xx: fix typo in network defaults
Commit 9fec39a (ar71xx: add support for TP-Link TL-WA855RE v1) introduced a
typo in 02_network, fix it by removing the stray paren.

Reported-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-06-29 18:04:29 +02:00
Piotr Dymacz
a73471dea7 ar71xx: image: specify TPLINK_HWID for TP-Link RE450
TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin.
As we don't want to break sysupgrade (all existing LEDE release images
for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0.

Fixes FS#852

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:46:08 +02:00
Piotr Dymacz
24043a0d2e ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.

The difference between these two models is in number of available
LEDs, buttons and power input switch.

This work is partially based on GitHub PR#974.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
  switch

* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Factory image notes:

These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.

We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.

Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.

The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".

Flash instruction:

Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

To access U-Boot CLI, keep pressed "4" key during boot.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
c55fadcacb ramips: image: simplify TP-Link Archer devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
5b7f592251 build: move mktplinkfw2 related commands to image-commands.mk
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
7d6c63d875 build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
ad8c315812 ar71xx: fix switch port mapping for TP-Link TL-WR74xN/D series
Fixes FS#843

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Henryk Heisig
b05c7193fd ar71xx: add support for TP-Link Archer C58 v1
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-06-29 10:37:36 +02:00
Federico Cappon
9fec39a033 ar71xx: add support for TP-Link TL-WA855RE v1
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Federico Cappon <dududede371@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
656ed7544f ar71xx: fix EnGenius ENS202EXT mtd definition
Use statically defined sizes for kernel and rootfs mtd partitions.
Vendor upgrade script writes both firmware parts independently which
ends up in a gap between kernel and rootfs images. This results in
incorrectly calculated rootfs_data start offset.

Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL
definition.

Fixes FS#835

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Camille Bilodeau
bb46b635df ar71xx: move Arduino Yun to generic building code
Migrate Arduino Yun from legacy to generic building code.

Note: the mtd partitioning is changed to adopt the LEDE default
partitioning. It allows to have a kernel bigger than 1280k. It is
necessary as kernel > 4.4 with default LEDE configuration grows
bigger.

To use the new partitioning, you need to update your U-Boot env in
advance:

setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
saveenv

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Camille Bilodeau
2fa58a8d7c ar71xx: remove Arduino Yun 8 MiB prototype
The Arduino Yun has 16 MiB flash. Early prototype boards with 8 MiB were
not available for sell:

https://blog.arduino.cc/2013/08/21/updating-about-arduino-yun-and-arduino-robot/

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Leon M. George
3e12ca2355 ar71xx: wpj344: set MAC on wan
Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-06-29 10:37:36 +02:00
Leon M. George
98c5a71dfd ar71xx: wpj344: remove unused eth1 device
Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-06-29 10:37:36 +02:00
Leon M. George
c777fd8a7e ar71xx: wpj344: read MAC addresses from u-boot mtd
This way, the assigned addresses match those on the barcode labels.
Otherwise, the addresses appear to vary on boot.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-06-29 10:37:36 +02:00
Stijn Tintel
880f73c327 kernel: cleanup CONFIG_SCHED_HRTICK
Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the
generic config in b47fd76563.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-29 04:46:59 +02:00
Stijn Tintel
1e91855af2 armvirt: rename config-default to config-4.9
The kernel configs for all targets should have the version in the
filename, for clearness and consistency across all targets.
It is also expected by the update_kernel.sh script.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-29 03:36:19 +02:00
Rafał Miłecki
76c460b584 kernel: backport usbport LED trigger driver support for DT
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-06-28 11:31:38 +02:00
Michael Heimpold
f788fd0fd3 mxs: drop 4.4 support
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2017-06-27 23:22:25 +02:00
Michael Heimpold
9eb68f020b mxs: add support for 4.9 and switch over
I did not port the regulator and power patches from Stefan Wahren
because I talked to him and he told me that work on this is currently
stalled. And since AFAIK nothing depends on these patches, leaving them
out seems reasonable.

I build minimum default configurations and run-tested them on both
I2SE Duckbill devices and Olimex Olinuxino Maxi boards successfully [1].

[1] Tested:
- debug uart is working
- boot without any obvious kernel problem
- network is coming up and data transfer is possible
- Olinuxino: USB detects a plugged-in pen drive

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
[refreshed config and patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-06-27 23:22:25 +02:00
Michael Heimpold
8794954d10 kernel: disable various symbols for v4.9
In preparation for bumping mxs target to 4.9, disable a bunch of configuration
symbols that provoked config prompts.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2017-06-27 23:22:25 +02:00
Stijn Tintel
f80963d4d1 kernel: update kernel 4.4 to 4.4.74
Refresh patches.
Compile-tested on ar71xx.
Runtime-tested on ar71xx.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-27 07:42:50 +02:00
Koen Vandeputte
69649a1b45 kernel: update kernel 4.9 to 4.9.34
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)

Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-27 07:21:03 +02:00
Stijn Tintel
d18f76f762 kernel: use .patch extension for all patches
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-27 06:37:46 +02:00
Alexander Couzens
d98cafc7b6
ar71xx/images/senao: fix reproducible issue using tar
Use deterministic sorting
Use numeric owner/group
Set uid/gid to 0

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-25 12:14:26 +02:00
Alexander Couzens
d6331d5583 ar71xx/image: make tar calls reproducible
Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-25 12:11:41 +02:00
Christian Lamparter
6adc757097 apm821xx: MR24: fix ethernet phy detection on the MR24
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This patch fixes a problem where the AR8035 PHY can't be
detected on the Cisco Meraki MR24, when the ethernet cable
is not connected during boot.

Russell Senior reported:
|This appears to be a problem during probing of the AR8035
|phy chip. When ethernet has no link, the phy detection fails,
|and eth0 is not created. Plugging ethernet later has no effect,
|because there is no interface as far as the kernel is
|concerned. The relevant part of the boot log looks like this:
|
|[    0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[    0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[    0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
(<https://bugs.lede-project.org/index.php?do=details&task_id=687>)

Fixes FS#687
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-06-24 22:36:38 +02:00
Mathias Kresin
1faff3b7e3 ramips: add MT7603E driver to AFoundry EW1200
Add the MT7603E driver for the 2.4GHz wireless.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
e7cd6f5d66 ar71xx: add AVM FRITZ!WLAN Repeater 300E support
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
0605b15be4 ar71xx: add AR724x PCIe init fixes
Add upstream send AR724x PCIe patches to get the PCIe controller out of
reset during driver init.

The AVM Fritz 300E bootloader doesn't take care of releasing the
different PCIe controller related resets which causes an endless hang
as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
8e0d7d6574 build: move lzma2eva build step to image-commands.mk
Move it to image-commands.mk so that it can used by other targets with
eva based boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
d165f1f3bc kernel: move Lantiq PEF7061/7071/7072 phy driver to generic
The driver is used for boards outside the lantiq target as well. Move
it to generic to make it available for more targets.

The phy driver is included in kernel 4.8 as INTEL_XWAY_PHY.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Rafał Miłecki
f5f1d40b5e kernel: backport MTD patch extracing TRX code to separated parser
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-06-23 11:54:20 +02:00
Rafał Miłecki
4d5f296af8 kernel: backport upstream mtd support for partition parsers
In a log term it should replace our implementation. For now both can
coexist.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-06-23 11:40:05 +02:00
Rafał Miłecki
8c1e760ab6 kernel: backport upstream mtdpart.c cleanups
Except for renames and line changes the only conflict was in
allocate_partition in handling MTD_WRITEABLE. Hopefully it was handled
correctly.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-06-23 11:40:05 +02:00
Rafał Miłecki
4052443a23 kernel: don't switch allocate_partition to use mtd_roundup_to_eb
This mtd_roundup_to_eb helper was introduced years ago in the commit
daec7ad768 ("kernel/3.10: add separate rootfs partition parser") and
it was probably supposed to simplify code a bit.

With the recent upstream commit 1eeef2d7483a7 ("mtd: handle partitioning
on devices with 0 erasesize") the logic in allocate_partition got
slightly more complex and we can't use this simple helper anymore as it
doesn't support MTD_NO_ERASE properly.

There also isn't any real gain from this helper, so it's probably easier
to just don't use it *or* work on upstreaming it to avoid maintenance
cost.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-06-23 10:09:57 +02:00
Mathias Kresin
3ccca56eb0 ramips: remove optional ucidef_set_led_rssi parameters
The same values are set if the parameters are not specified.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-17 15:38:20 +02:00
Pavlo Samko
82f9486142 ramips: add support for TRENDnet TEW-638APB V2
This patch add support for the TRENDnet TEW-638APB V2.

Specification:
- SoC: Ralink SoC RT3052F
- Flash: 4MB
- RAM: 32MB
- Ethernet: 1x LAN (100 Mbps)
- Wireless: 2.4GHz b/g/n, 2x external antenna
- Buttons: 1x Reset, 1x WPS
- LEDs: Power (green), Ethernet (green), WPS (green and orange),
  Wireless (green)
- UART: 1x UART on PCB (3.3V, GND, RX, TX) - 57600 8N1

Installation

via vendor firmware:
- upload sysupgrade.bin image

via TFTP:
- stop uboot into tftp-load into option "2"
- upload sysupgrade.bin image

Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
2017-06-17 15:38:19 +02:00
Mathias Kresin
259fc1e778 lantiq: show xdsl line init status on shared dsl/internet led
On boards which don't have a distinct internet and dsl led, use the
shared LED to indicate the xdsl line state and any traffic that is
send/received via the netdev. This traffic doesn't necessarily need to
be internet traffic.

Rename the shared LED of existing configs to "dsl", to match the new
defaults. The configuration of the to be renamed LED is identical with
the new defaults.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-17 15:38:18 +02:00
Martin Schiller
03776d813c lantiq: restore netdev trigger of dsl led on line up
Allows to use a single LED for line init status indication and to show
any rx/tx activity on a synchronized dsl line.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-17 15:34:16 +02:00
Pavel Kubelun
189239ade3 ipq806x: qca99xx: fix wifi calibration
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.

Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).

Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-06-17 11:51:41 +02:00
Daniel Golle
d80d1b6c42 imagebuilder: don't rewrite package list output
No longer rewrite opkg list output in package_list function, remove
the awk call in the pipe (which was intended for a single specific
use-case).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-06-17 01:24:43 +02:00
Daniel Golle
1b555e1d2b imagebuilder: clean package_list
commit 19ac879954 (imagebuilder: add package_list function) introduced
a new function 'package_list' to the imagebuilder Makefile.
Unfortunately the package list was poluted by stdout noise of the
Makefile itself as well as opkg. Redirect those outputs to stderr to
make sure that the package_list returned doesn't contain progress
info output but really only packages.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-06-17 00:54:46 +02:00
Paul Spooren
19ac879954 imagebuilder: add package_list function
The imagebuilder can now list all available packages by using make
package_list. This is usefull for scripts to retrieve a list of all
packages with versions (and size)

Signed-off-by: Paul Spooren <paul@spooren.de>
[daniel@makrotopia.org: fixed commit message]
2017-06-15 00:36:08 +02:00
小桥
a3332f2aa2 ramips: fix Phicomm K1S(PSG1208) pinmux
Use gpio function for pins with LEDs.

Signed-off-by: 小桥 <29551030@qq.com>
2017-06-12 21:08:54 +02:00
Makoto Takeuchi
ca27b3d370 kirkwood: add support for Cisco ON100
The Cisco ON100 device is a Kirkwood based router:

    SoC: Marvell 88F6282 1600Mhz
    SDRAM memory: 512MB DDR3 1333Mhz
    Gigabit ethernet: 2x Marvell 88E1310 (over RGMII)
    Flash memory: 512MB
    2 bi-colour status LEDs (green/red)
    1 Reset button
    1 USB 2.0 port (on back)
    1 SDIO slot (on back)

This commit adds a target profile of "Cisco Systems ON100" under the target
system "Marvell Kirkwood".

Flashing can be performed over tftp, once "dhcp" has been issued:
 tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin
 nand erase 0x0c0000 ${filesize}
 nand write ${loadaddr} 0x0c0000 ${filesize}

Once flashed, set environment variables to boot:
 setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs
  \; bootm
 saveenv

Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
2017-06-12 21:07:31 +02:00
Ben Whitten
c2f052acae at91: convert boards to generic build target
Evaluation boards are left in component form to ease flashing
using vendor tooling and instructions. These boards also do
not include the EOF marker in the UBIFS as the bootloaders
are recent and easily upgradeable.

The end product boards use factory.bin images based on the
dts layout and include EOF markers as bootloader UBI support
is not determined.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-12 21:07:31 +02:00
Piotr Dymacz
3ff31586eb ar71xx: image: simplify TP-Link devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
8b556fb056 ar71xx: image: fix TP-Link TL-WR710N v2/v2.1 BOARDNAME
All TP-Link TL-WR710N versions share the same machine code.

This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
7efe0cd83d ar71xx: image: tp-link.mk: keep devices in alphabetical order
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
a41f38e61d ar71xx: base-files: cleanups in 10-ar922x-led-fix
Fix code style, indentation and leading/trailing whitespaces in:
/etc/hotplug.d/net/10-ar922x-led-fix

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
b73cb365d5 ar71xx: base-files: cleanups in 11-ath10k-caldata
Fix code style and boards alphabetical order in:
/etc/hotplug.d/firmware/11-ath10k-caldata

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Ludwig Thomeczek
b4711dbad3 ar71xx: add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[minor code style fixes, boards alphabetical order fixes,
reworked commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Serg Studzinskii
b7cc661615 ar71xx: add support for TP-Link TL-WR942N v1
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
641af0c39d ar71xx: move WRTnode2Q to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
636ae9e9a0 ar71xx: image: simplify Ubiquiti devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
01aa23acf7 ar71xx: image: mikrotik: shorten DEVICE_TITLE
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
7bc5571d14 ar71xx: image: use simply expanded variables
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
80136e57a4 ar71xx: image: update GL.iNet boards DEVICE_TITLE
Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:31:25 +02:00
Piotr Dymacz
93198b8335 ar71xx: image: fix 8devices boards DEVICE_TITLE
Be consistent with DEVICE_TITLE syntax and use vendor + board names.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:30:05 +02:00
Piotr Dymacz
bd92a6cf57 ar71xx: image: drop unused mtdlayouts from legacy.mk
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
708cc2bd3c ar71xx: image: cosmetic: drop redundant empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
e83cac1a8f ar71xx: image: add ROOTFS_SIZE to DEVICE_VARS
Also use ROOTFS_SIZE variable in place of static values.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
c00fb14329 ar71xx: image: keep custom Build/* functions in separate files
Most of the custom Build/* functions in ar71xx target are rarely used by
image building code for devices from more than one subtarget. As they
don't need to be always included, move them to corresponding *.mk files.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
3a3cd0ac43 ar71xx: image: keep DEVICE_VARS and Build/* at the beginning
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:21:45 +02:00
Piotr Dymacz
af27dd1a51 ar71xx: image: simplify Compex devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Piotr Dymacz
43c0ef1010 ar71xx: image: drop redundant kmod-usb-ohci from DEVICE_PACKAGES
kmod-usb-ohci is needed only on devices with AR71xx and AR7240 SoCs.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Piotr Dymacz
05e276c071 ar71xx: image: drop redundant uboot-envtools from DEVICE_PACKAGES
uboot-envtools is already included in DEFAULT_PACKAGES for ar71xx.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 19:06:49 +02:00
Kevin Darbyshire-Bryant
8960f2b80c
ar71xx: fixup ar71xx/ar933x_wmac_reset: remove indefinite wait for wmac reset
Fix malformed patch introduced by 296312fca1

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2017-06-11 17:12:45 +02:00
Alexander Couzens
ab11618001 ar71xx/ar93xx_wmac_otp_read_word: fix wrongly used sizeof(*u)
Found-by: Coverity Scan #1330474
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-11 14:22:44 +02:00
Alexander Couzens
878cd77026 linux/swconfig_get_attr: fix leak of msg in case of error
Found-by: Coverity Scan #1330102
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-11 14:22:44 +02:00
Alexander Couzens
814e1695aa linux/ledtrig-netdev: remove unsigned < 0 check
Found-by: Coverity Scan
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-11 14:22:44 +02:00
Alexander Couzens
296312fca1 ar71xx/ar933x_wmac_reset: remove indefinite wait for wmac reset
Found-by: Coverity Scan #1329327
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-11 14:22:44 +02:00
Alexander Couzens
1025941662 ar71xx/ag71xx_ethtool: don't return uninitialized return value on success
ag71xx_ethtool_set_ringparam() will return an uninitialized value on
success.

Found-by: Coverity Scan #1330877
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-11 14:22:44 +02:00
Alexander Couzens
64cd4b48e8 ar71xx/ag71xx_mdio_probe: fix a memory leak when probe fails
Found-by: Coverity Scan #1330233
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-11 14:22:44 +02:00
Alexander Couzens
d18cb142d5 ar71xx/ag71xx_ar7240_get_port_link: fix off-by-one check on argument port
Found-by: Coverity Scan #1329901
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-11 14:22:44 +02:00
Jonas Gorski
b43c190079 brcm63xx: probe SPI connected switches through DT
Now that we can configure the switches through DT, do so.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-10 12:40:38 +02:00
Jonas Gorski
5df15c06cc b53: allow configuration through device tree
Add support for the same binding as upstream b53 to allow an
easy switch.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-10 12:40:38 +02:00
Jonas Gorski
9ceeaf4c6c brcm63xx: switch to hardware led controllers
Instead of bit banging SPI to talk to the GPIO chip, use the hardware
led controllers intended for controlling the LEDs.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-10 12:40:38 +02:00
Jonas Gorski
0aa366c6e0 brcm63xx: leds-bcm6328: fix signal assignments for leds 4~7
Properly use modulus for bit calculation for LEDs 4 to 7.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-10 12:40:38 +02:00
Jonas Gorski
c5d394e9ba brcm63xx: dsl-275xb-d: configure switch leds
Add pinctrl configuration to configure the switch leds on DSL-275XB.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-10 12:40:38 +02:00
Jonas Gorski
0755c2d117 brcm63xx: add pinctrl support
Add and enable pincontrol drivers, and update dts(i) files with
appropriate hogs.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-10 12:40:37 +02:00
Jonas Gorski
fd1096e351 kernel: make regmap LZO cache optional
There are no users, so hide it and let future users select it. Saves
about ~17 kB on MIPS.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-10 12:40:37 +02:00
Jonas Gorski
f9b7bfa088 brcm63xx: backport upstream generic gpio changes
Backport patches that add a data pointer to gpio_chip.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-10 12:40:37 +02:00
Rafał Miłecki
c00fbaf670 bcm53xx: include wpad-mini only on devices with (supported) wireless
Don't include wpad-mini when it's useless just like we don't include
useless wireless drivers.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-06-08 22:25:00 +02:00
Jo-Philipp Wich
55623a9c83 kernel: update kernel 4.9 to 4.9.31
Fixes the following security vulnerabilities:

CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.

CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.

CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.

CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.

Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.9.31

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-06-08 01:03:39 +02:00
Jo-Philipp Wich
f4a4f324cb kernel: update kernel 4.4 to 4.4.71
Fixes the following security vulnerabilities:

CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.

CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.

CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.

CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.

Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.71

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-06-07 21:40:42 +02:00
Sergey Ryazanov
67a322a79c kernel: remove CONFIG_ZONE_DMA_FLAG from 4.9
There are no CONFIG_ZONE_DMA_FLAG config symbol since 4.7.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 18:31:10 +02:00
Sergey Ryazanov
68e7a2a0b7 kernel: disable CONFIG_SG_POOL by default
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 18:31:10 +02:00
Sergey Ryazanov
6a3d82a3fa ath25: add missed HAVE_IRQ_EXIT_ON_IRQ_STACK
Add HAVE_IRQ_EXIT_ON_IRQ_STACK kernel configuration symbol that was
missed during backporting separate IRQ stack for MIPS from upstream.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 18:31:10 +02:00
Felix Fietkau
2dc23a7576 rb532: enable high-res timers, refresh kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-06-07 18:31:10 +02:00
Felix Fietkau
f859a7b696 xburst: enable high-res timers, refresh kernel config
Helps with system performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-06-07 18:31:10 +02:00
Felix Fietkau
1d44593c49 octeon: enable high-res timers
Helps with network stack performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-06-07 18:31:10 +02:00
Felix Fietkau
b47fd76563 kernel: add CONFIG_SCHED_HRTICK=y to the generic config
It is used by pretty much every target

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-06-07 18:31:10 +02:00
Lucian Cristian
cdedb24ef8 x86: include USB HID by default
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2017-06-07 18:31:10 +02:00
Sergey Ryazanov
00639586fd kernel: update myloader for linux 4.9
add backport patches for older kernels.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 17:19:48 +02:00
Sergey Ryazanov
2cc61e6e8e ip17xx: correct aneg_done return value
PHY core treats any positive return value as the auto-negotiation done
indication. Since we do not actually check any device register in this
callback then update it to return positive value with a neutral meaning
instead of the register flag to avoid  confusing for future readers.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 11:06:29 +02:00
Sergey Ryazanov
913b2290ca mvswitch: fix autonegotiation issue
The Marvel 88E6060 switch has an MDIO interface, but does not emulate
regular PHY behavior for the host. The network core can not detect using
the generic code, whether the connection via the attached PHY can be
used or not. The PHY's state machine is stuck in a state of
auto-negotiation and does not go any further so the Ethernet interface
of the router stay forever in the not-runing state.

Fix this issue by implementing the aneg_done callback to be able to
inform the network core that the Ethernet interface link to which the
switch is connected can be marked as RUNNING.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 11:06:12 +02:00
Sven Roederer
cc722bec97 linux/ath25: fixing some tabs and whitespace
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-06-07 06:50:16 +02:00
Sergey Ryazanov
8a3a71084c ath25: drop 4.4 kernel support
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 06:49:46 +02:00
Sergey Ryazanov
0f4943211c ath25: switch to 4.9 kernel
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 06:47:10 +02:00
Sergey Ryazanov
3e3d482c98 ath25: 4.9: fix Ethernet link autonegotiation
Drop the own PHY polling function and switch to using the kernel PHY
state machine. This change allows driver to work correctly with devices
that do not support PHY behaviour but whose driver could emulate
autonegotiation completion (e.g. MV88E6060 and IP17xx switches).

NB: earlier this driver rely on flaws in PHY core code and could use PHY
device without really starting it. But now (at least in kernel 4.9)
this trick no more work and network interface could stuck in not-running
state.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 06:47:03 +02:00
Sergey Ryazanov
b1cc215d27 ath25: 4.9: fix Ethernet tiny issues
Few tiny fixes for issues caused by changes in the upstream:
 - do not touch PHY IRQ array (core code initializes it itself now)
 - add missed SET_NETDEV_DEV() invocation (causes segfault during phy
   connection)
 - use phy API inside the MDIO probe function instead of direct field
   access (consider phy structure changes in upstream and prevent
   similar issues in the future)

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 06:46:52 +02:00
Sergey Ryazanov
0827a0b4f1 ath25: 4.9: fix GPIO compile issues
Consider renaming the dev field to parent in the upstream.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 06:46:44 +02:00
Sergey Ryazanov
64083848e2 ath25: add preliminary kernel 4.9 support
Copy and refresh patches and config from 4.4

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 06:46:34 +02:00
Sven Roederer
9715beb04c ramips: add support for Ubiquiti EdgeRouter X-SFP
This patch adds support for the Ubiquiti EdgeRouter X-SFP and
improves support for the EdgeRouter X (PoE-passthrough).

Specification:
- SoC: MediaTek MT7621AT
- Flash: 256 MiB
- RAM: 265 MiB
- Ethernet: 5 x LAN (1000 Mbps)
- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
- EdgeRouter X:
  - 1 x PoE-Passtrough (Eth4)
  - powered by Wallwart or passive PoE
- EdgeRouter X-SFP:
  - 5 x PoE-Out (24V, passive)
  - 1 x SFP (unknown status)
  - powered by Wallwart (24V)

Doesn't work:
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.

Installation

via vendor firmware:
- build an Initrd-image (> 3MiB) and upload the factory-image
- initrd can have luci-mod-failsafe
- flash final firmware via LuCI / sysupgrade on rebooted system

via TFTP:
- stop uboot into tftp-load into option "1"
- upload factory.bin image

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-06-07 06:33:33 +02:00
Ram Chandra Jangir
e178d51a04 ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 board
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.

Testing:
 *Tested on IPQ40xx AP-DK04.1-C1:
   a. NAND boot
   b. ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-06-07 06:33:33 +02:00
Ram Chandra Jangir
5e1cc0c090 ipq806x: Updated various ipq40xx pin definitions
This change populates default values for various GPIO functions
in ipq40xx pinctrl driver.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-06-07 06:33:33 +02:00
Kristian Evensen
1898f7339f Add missing APU1 reference to x86 board.d
x86 board.d only contains a case for the APU2, not the APU1. This
causes, for example, network configuration not to be created correctly.
Even though the APU1 seems to reaching EOL, there a still a lot of them
out there.

The APU1 and APU2 is configured in the same way and this patch should
also be considered for stable, as the error also exists there.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-06-06 23:01:53 +02:00
Jonas Gorski
334f8f4fc3 brcm63xx: drop support for specifying SPI flash part parsers
No need to keep this since we set them from device-tree.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 11:33:44 +02:00
Jonas Gorski
092ac42e1e brcm63xx: drop support for caldata in brcm63xxpart
Now that we always provide these partitions through DT, we don't need to
pass their data through parser data from board files anymore.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 11:33:44 +02:00
Jonas Gorski
474cde6123 brcm63xx: probe SPI flash through DT
Now that we support problem the SPI controllers through DT, we can also
probe flash through DT.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 11:33:44 +02:00
Jonas Gorski
97b36aca09 brcm63xx: add pflash for remaining pflash equipped boards
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 11:33:44 +02:00
Jonas Gorski
31c3ac1118 brcm63xx: do not require fixed partitions when probing from DT
Allow the parser to be invoked from DT without fixed cfe/linux/nvram
partitions. This allows flash to be probed from DT also for multi
flash-size images.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 11:33:44 +02:00
Jonas Gorski
b50fd8c2b3 brcm63xx: register SPI controllers through DT
Register SPI controllers through device tree. We will wire up the clocks
at a later stage.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 11:33:43 +02:00
Jonas Gorski
2a2b16210b brcm63xx: backport upstream solution for SPI message size limits
Backport upstream solution for working around SPI controller maximum
message sizes.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 10:40:00 +02:00
Jonas Gorski
f62e02cf20 brcm63xx: update flash of_node patches to full patch set
Fixes missing of_node for SPI flash probed through devicetree.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 10:40:00 +02:00
Jonas Gorski
d298576739 brcm63xx: refresh kernel config
Ensure the config is ordered and has all recent symbols.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-06-04 10:40:00 +02:00
Tino Reichardt
e097eb27af lantiq: fix 0008-MIPS-lantiq-backport-old-timer-code.patch for Amazon-SE
The patch 0008 removes the vanilla kernel gptu.c of lantiq.
But the replacement file timer.c does not work Amazon-SE and
is also protected therefore with an CONFIG_SOC_AMAZON_SE :-)

This commit will re-activate the default vanilla kernel code
in gptu.c for Amazon-SE.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
[refresh patches and add same change for kernel 4.9]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-06-03 21:35:53 +02:00
Tino Reichardt
712ebe95f8 lantiq: add Allnet ALL0333CJ support
This patch adds support for the Allnet ADSL2+ Modem ALL0333CJ.

Specifications:
- SoC: Amazon-SE
- RAM: 16MB
- Storage: 4MB NOR FLash
- LEDs: Power, Ethernet, DSL (Sync)
- Buttons: 1x Reset Button (not currently supported, will be done)
- 1x Ethernet-Port: 1x RJ45 10/100BaseTX
- 1x WAN-Port: AnnexB & J, G.992.1(ADSL), G.992.3(ADSL2), G.992.5(ADSL2+)

Installation:
- can be done via telnet+tftp or serial console
- default passwords:
  - via telnet (root:admin)
  - via webinterface http://172.16.1.254:8235/ (admin:coolwhite)

Installation via telnet / tftp:
host: # your own host must have an tftpd daemon, then do this:
host: ifconfig eth0:172 172.16.1.1 up
host: # telnet to allnet modem, root:admin
host: telnet 172.16.1.254
modem: # kill this daemon, it spams your console
modem: killall dsl_cpe_control
modem: # change to some place in ram:
modem: cd /ramdisk/tftp_upload
modem: # load lede-lantiq-ase-ALL0333CJ-squashfs-sysupgrade.bin alias uImage
modem: tftp -g -r uImage 172.16.1.1
modem: # load these extra tools from your tftpd via:
modem: # source: https://github.com/mcmilk/uboot-utils/releases/download/0.1/mips32.tar.gz
modem: tftp -g -r flashwrite 172.16.1.1
modem: tftp -g -r fw_setenv 172.16.1.1
modem: tftp -g -r fw.conf 172.16.1.1
modem: ln -s fw_setenv fw_printenv
modem: chmod +x *
modem: ./fw_setenv disable_recovery y
modem: ./fw_setenv kernel_addr 0xb0010000
modem: ./flashwrite /dev/mtd/1 uImage 0

Installation via serial line at uboot:
uboot: # erase everything exept bootloader
uboot: protect on b0000000 +10000; protect on b03f0000 +10000
uboot: erase all
uboot: # get new firmware via tftp:
uboot: tftpboot 0x80100000 uImage; setenv kernel_addr 0xb0010000
uboot: # copy to flash:
uboot: cp.b 0x80100000 $(kernel_addr) $(filesize)
uboot: # disable proprietary image checking:
uboot: setenv disable_recovery=y; saveenv
uboot: # reboot with LEDE ;)
uboot: reset

Ethernet works as expected, DSL syncronization does not work properly
currently, I am working on this issue.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Tino Reichardt
995ad357f9 lantiq: enable Netgear DGN1000B image build
Enable the building of Netgear DGN1000B images. I have an
example device here, but it was not tested currently.
Also WLAN and USB is not ready in the moment.

This is just the proper way, so that developing on this
device is known to be done in the near future.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Tino Reichardt
9b321bc60d lantiq: add Amazon-SE subtarget
Re-Add support for the Amazon-SE subtarget on Lantiq.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Tino Reichardt
1039e41dea lantiq: fix amazonse.dsti
Add missing memory@0 and localbus@0 sections.
Fix MEI and GPTU interrupt definitions.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Daniel Golle
bfa2e945de ramips: enable PCIe on MT7688
Submitted upstream as well, see
patchwork https://patchwork.linux-mips.org/patch/16223/

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-06-03 20:45:38 +02:00
Helge Mader
63a20c95fd lantiq: modified lantiq_dsl.sh status output of latency
Signed-off-by: Helge Mader <ma@dev.tdt.de>
2017-06-02 22:49:45 +02:00
Helge Mader
666dd85b36 lantiq: fix lantiq_dsl.sh status and lucistat output
Signed-off-by: Helge Mader <ma@dev.tdt.de>
2017-06-02 22:49:33 +02:00
Daniel Engberg
22ac4bd555 mvebu: Add block device sd to default kernel config
Add block device sd to kernel config otherwise AHCI/eSATA devices won't get enumerated in /dev

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2017-06-02 12:02:21 +02:00
Jo-Philipp Wich
1893b5622d x86: disable X2APIC support for legacy subtargets
Explicitely disable X2APIC support on legacy targets since the targeted
processor types do not support it anyway there.

Fixes FS#285.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-06-02 01:51:03 +02:00
Matthias Schiffer
5654a03768
mvebu: fix sysupgrade
mvebu was modifying RAMFS_COPY_BIN and RAMFS_COPY_DATA from a
sysupgrade_pre_upgrade hook. As the ramfs is created from stage2, this
did not have an effect anymore after the staged sysupgrade changes.

As it doesn't really hurt to copy fw_printenv and fw_setenv
unconditionally, simply add them in /lib/upgrade/platform.sh, so stage2
will see them.

Config copying is moved to a function called by platform_copy_config, where
it belongs.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: FS#821
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
2017-06-01 20:41:19 +02:00
John Crispin
7f9143168f ramips: add jumbo frame support for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-06-01 12:30:17 +02:00
John Crispin
9bc9457b85 ramips: fixup nand support on v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-06-01 12:30:17 +02:00
Sergey Sergeev
9e1bc27e6d ar71xx: Fix UBIFS work on Mikrotik RB95x devices
If nand chip has no NAND_NO_SUBPAGE_WRITE flag on its options
ubifs can't use it mtd devices and the kernel crashes with error:
__nand_correct_data: uncorrectable ECC error

Signed-off-by: Sergey Sergeev <adron@yapic.net>
2017-05-31 11:36:21 +02:00
Koen Vandeputte
3b4241071d imx6: disable UART dma
Fixes these prints on boot:

[   13.785600] imx-uart 2020000.serial: DMA transaction error.
[   13.793134] imx-uart 2020000.serial: DMA transaction error.
[   13.798721] imx-uart 2020000.serial: DMA transaction error.

Based on following upstream patch by Tim Harvey (Gateworks):

80a01b6582

TX complete DMA messages are getting missed.
This is also currently an issue in mainline.
For now we will disable DMA in serial/imx.c.

This resolves an issue encountered with RS485 transmit.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-05-31 08:45:26 +02:00
Enrico Mioso
acd8649b18 ramips: let the "reserved" MTD partition be RO for R6220
The "reserved" partition should probably be read-only, just in case. Even
not knowing it's content, other devices have marked it as such, so it
seems a good idea to do so also for this device.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Mathias Kresin <dev@kresin.me>
CC: Hanqing Wong <hquu@outlook.com>
2017-05-31 08:45:02 +02:00
Jo-Philipp Wich
66f25c98e0 ar71xx: disable ENS202EXT in mikrotik and nand subtargets
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-05-31 02:40:47 +02:00
Piotr Dymacz
6173f6d8f1 ar71xx: move Wallys DR344 to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:34:09 +02:00
Piotr Dymacz
18d5cee2a8 ar71xx: fix Wallys DR344 GPIO-connected LEDs and button
This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.

Actually, DR344 has 6 GPIO-connected LEDs and one button:

- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan

WAN LED is connected directly with AR8035 PHY.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:34:04 +02:00
Piotr Dymacz
6713640b52 ar71xx: set GE interface as wan by default in Wallys DR344
This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:15:25 +02:00
Piotr Dymacz
c7bc8a9a13 ar71xx: fix GE interface support in Wallys DR344
GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:15:25 +02:00
Marty Plummer
558d86923e ar71xx: add support for EnGenius ENS202EXT
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.

The device is based on Qualcomm/Atheros AR9341 v1.

Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button

Flash instructions:

You have three options:

- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.

- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.

- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:

*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
      stat -- Status
       sys -- System
    wless2 -- 2.4G-Wireless
      mgmt -- Management
      tree -- Tree
      help -- Help
    reboot -- Reboot
ens202ext>mgmt
  Management
---========= Commands Help =========---
     admin -- Administration
     mvlan -- Management VLAN settings
      snmp -- SNMP settings
    backup -- Backup/Restore settings
    autorb -- Auto reboot settings
   fwgrade -- Firmware upgrade
      time -- Time settings
   wifisch -- Wifi schedule
       log -- Log
      diag -- Diagnostics
      disc -- Device Discovery
    logout -- Logout
      help -- Help
      exit -- Exit
ens202ext/mgmt>fwgrade
  Management --> Firmware upgrade
---========= Commands Help =========---
      fwup -- Firmware upgrade
      help -- Help
      exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin

Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
2017-05-30 14:15:25 +02:00