When in ra server mode, configure nameservers passed in router
announcements from the dns value (which is already used by odhcpd).
This also fixes FS#677 by using the global IPv6 address of the router
instead of the link local address (if no nameservers are configured).
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
We enabled lua interpreter by default as it doesn't make any problem in the uhttpd config file and we modify the index page to use it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
93abe6f config: fix invalid hoplimit in RA message
2ae08d1 config: fix invalid retranstime in RA message
0005cb4 config: fix invalid reachabletime in RA message
5683dd2 config: limit ra_mtu to 65535
f8d40a5 router: fix interface mtu read error
f8f4b87 config: limit ra_retranstime to 60000
a2d8bf6 dhcpv4: display two hex digits per octet in syslog
a9e9bc4 config: make RA retransTime configurable via uci
2cb6b48 config: make RA reachableTime configurable via uci
e4504db config: make RA curHopLimit configurable via uci
9dd5316 config: make RA mtu configurable via UCI
29cb2ff config: fix dhcpv4 server being started
0ef74ec ndp.c: add switch/case fallthrough comments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
None of the variables in this "local" declaration are actually set in
wpa_supplicant_add_network().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This patch adds the interface-name option for each dhcp config
in /etc/config/dhcp.
With the interface_name option users can define a DNS name for each dhcp section
that will be resolved by dnsmasq with the underlaying interface address.
For example:
config dhcp 'lan'
option interface 'lan'
...
list interface_name 'home.lan'
...
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If there's a TFTP root directory configured, create it with mkdir -p
(which does not throw an error if the folder exists already)
before starting dnsmasq. This is useful for TFTP roots in /tmp, for example.
Originally submitted by nfw user aka Nathaniel Wesley Filardo
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Setting legacy_rates to 0 disables 802.11b data rates.
Setting legacy_rates to 1 enables 802.11b data rates. (Default)
The basic_rate option and supported_rates option are filtered based on this.
The rationale for the change, stronger now than in 2014, can be found in:
https://mentor.ieee.org/802.11/dcn/14/11-14-0099-00-000m-renewing-2-4ghz-band.pptx
The balance of equities between compatibility with b clients and the
detriment to the 2.4 GHz ecosystem as a whole strongly favors disabling b
rates by default.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, defaults change]
When sta is configured, hostapd receives 'stop' and 'update' command from
wpa_supplicant. In the update command, hostapd gets sta parameters with
which it configures ap.
Problem is, with the default wireless configuration:
mode:11g freq:2.4GHz channel:1
If sta is connected to 5GHz network, then ap does not work. Ideally with
340-reload_freq_change.patch hostapd should reload the frequency changes
and start ap in 5GHz, but ap becomes invisible in the network.
This issue can be reproduced with following /etc/config/wireless:
config wifi-device radio0
option type mac80211
option channel 1
option hwmode 11g
option path 'virtual/uccp420/uccwlan'
option htmode 'none'
config wifi-iface 'ap'
option device 'radio0'
option encryption 'none'
option mode 'ap'
option network 'ap'
option ssid 'MyTestNet'
option encryption none
config wifi-iface 'sta'
option device radio0
option network sta
option mode sta
option ssid TestNet-5G
option encryption psk2
option key 12345
This change updates current_mode structure based on configured hw_mode
received from wpa_supplicant. Also prepare rates table after frequency
selection.
Signed-off-by: Abhilash Tuse <Abhilash.Tuse@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, patch refresh]
A number of small tweaks & improvements on the way to a final release.
Most notable:
Improve DHCPv4 address-in-use check.
Remove the recently introduced RFC-6842 (Client-ids in DHCP replies)
support as it turns out some clients are getting upset.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
9268ca6 ndp: don't trigger IPv6 ping when neighbor entry is invalid
2b3355f ndp: fix adding proxy neighbor entries
7dff5b4 ndp: fix wrong interface name in syslog message
a54afb5 dhcpv6-ia: Fix segfault when writing DHCPv4 leases in state file
c0e9dbf ubus: don't segfault when there're no leases
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Configuring dhcp_option as an option does not allow the usage of white
spaces in the option value; fix this by supporting dhcp_option as a list
config while still supporting the option config to maintain backwards
compatibility
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Install procd interface triggers only for interfaces which are enabled
so dropbear instances running on (an) enabled interface(s) are not
restarted due to an interface trigger of an interface which is disabled.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Based on a patch by Alexandru Ardelean.
netifd ubus reload call returns the actual reload error status;
return error status as well in reload_service
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
11cb9cf ubus: add interface method to trigger renew event
4375d1b system-linux: allow "throw" route type
5fbd904 netifd: propagate error code on netifd_reload()
6e0acec interface-ip: fix device name for IPv6 link-local DNS server
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The dep for the nftables support was wrong, if someone actually enable
that option gain a compilation error. This fix this problem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
minor/cosmetic: fixes the following misleading message:
root@box:~ /etc/init.d/dnsmasq restart
sh: out of range
Signed-off-by: Bastian Bittorf <bb@npl.de>
Update OpenVPN to 2.4.1
Remove 200-small_build_enable_occ.patch as it's included upstream.
Refresh patches
Add mirror and switch to HTTPS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Commit f4e312ddf8 adds libnetlink to
staging dir but did not add the header files libgenl.h and ll_map.h
which define functions belonging to libnetlink lib
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Similar to odhcpd, allow using ISC DHCPd instead of dnsmasq.
Disable DHCP and/or DHCP6 in case ISC DHCP is present and
enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The relay section should use the logical interface name and
not the linux network device name directly. This to be
consistent with other sections of the dnsmasq config where
'interface' means the logical interface.
Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
These are recommended practices by REC-22 and REC-24 of RFC6092:
"Recommended Simple Security Capabilities in Customer Premises Equipment
(CPE) for Providing Residential IPv6 Internet Service"
Fixes FS#640
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Make scan output useful for 802.11s meshes. The common print_ssid function
is used, so this doesn't add any additional code.
Based-on-patch-by: Jan-Tarek Butt <tarek@ring0.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
0463b05 dhcpv6: rebind capability support in reconfigure message (rfc6644)
53767fc dhcpv6: respect renew end point when handling reconfigure message
dd892e2 dhcpv6: calculate T1, T2 and T3 in a more sane manner
8a6ca6e md5: use libubox md5 library as local implementation
89822de dhcpv6: don't return renew msg in case of invalid msg type in reconfigure msg
4160c0e treewide: align coding style
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This change protects the openvpn instances to be marked as "in a crash
loop" and thereby the connection retries will run infinitely.
When the remote site of an openvpn connection goes down for some time
(network failure etc.) the openvpn instance in an openwrt/lede device
should not stop retrying to establish the connection.
With the current limit of 5 retries, there is a user interaction
required, which isn't really what you want when the device should
simply do everything to keep the vpn connection up.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add actual mirror and use main site as last resport
Source: http://www.tcpdump.org/mirrors.html
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
This includes following changes:
480d7bc Fix sending unicast questions on cache expire
a0403cd Keep source sockaddr for every cached DNS record
1478293 Fix code freeing cached non-A(AAA) records too early
9f1cc22 Fix replying to "QU" questions received on unicast interface
943bedb Fix reading port of incoming packets
c725494 Use MCAST_PORT define for port 5353
ce7e9e9 Use one define for DNS-Based Service Discovery service name
e1bacef Drop entries cached for interface we're going to delete
496aeba Fix comment typo in cache_gc_timer
f89986b Fix refreshing cached A(AAA) records that expire
Previous updates made umdns work as expected on startup but there were
still many bugs. They were mostly related to runtime - cache management
and requests + responses. E.g. umdns was never able to send question on
DNS record expire. It was also ignoring all incoming unicast questions.
Since these issues are quite serious it makes sense to backport this
update to the stable branch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
a032166 interface-ip: set prefix indicator flag when IPv6 prefix lifetime changes
b4f8984 system-linux: parse vti specific settings as nested json data object
7e3b89a system-linux: parse gre specific settings as nested json data object
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
If noresolv is set, we should not generate a --resolv-file parameter.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [minor cleanup]
This includes 3 cleanups:
fd5a160 Don't cache hosts as services
80dd246 Refresh DNS records A and AAAA directly
6515101 Access cached records (instead of services) to read list of hosts
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The kernel unconditionally pulls in a header file that defines
'current', which conflicts with the lua extension code.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes crash in interface_start caused by freeing interface in
interface_free without stopping a timeout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
RFC 6761 defines a number of top level domains should not be forwarded
to the Internet's domain servers since they are not responsible for
those domains.
This change adds a list of domains that will be blocked when 'boguspriv'
is used and augments that which is already blocked by dnsmasq's notion
of 'local service' using '--bogus-priv' i.e. RFC 1918 private addresses
and IPv6 prefixes as defined in RFC 6303.
To make this configurable rather than hard coded in dnsmasq's init
script, a new file /usr/share/dnsmasq/rfc6761.conf is conditionally
included.
The default file matches the RFC 6761 recommendation along with a few
other top level domains that should not be forwarded to the Internet.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Honour the parent interfaces peerdns option when spawning a virtual DHCPv6
interface in order to avoid pulling in IPv6 DNS servers when the user opted
to inhibit peer DNS servers in the configuration.
Fixes#597.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Pass down TARGET_CPPFLAGS for path to header files, and append the
libraries we depend on in TARGET_LDFLAGS. Put TARGET_LDFLAGS at the end
of the command line as is required by modern GCC/binutils.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes linking failures observed with external toolchains:
/home/florian/dev/toolchains/stbgcc-4.8-1.5/bin/../lib/gcc/mipsel-linux-gnu/4.8.5/../../../../mipsel-linux-gnu/bin/ld:
warning: libubox.so, needed by
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so,
not found (try using -rpath or -rpath-link)
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_open_nested'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_parse'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blob_nest_end'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_add_field'
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
thc-ipv6 did not allow an external environment to override CFLAGS, which
would lead to our CFLAGS not being passed properly (relro,
optimizations, etc...)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Drops a LEDE carried patch now upstream.
Convert to autotools.
A number of nits fixed upstream (dns & short packet handling most
notable)
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
When not defining 'device' or 'vlan' in relevant switch_port uci
sections, behaviour is inconsistent due to *devn, *port and *vlan
pointers not being zero initialized.
Signed-off-by: Ben Kelly <ben@benjii.net>
stop() is overwritten by rc.common, so implement stop_service instead.
While at it, remove the now unnecessary restart() override
Signed-off-by: Felix Fietkau <nbd@nbd.name>
--bogus-priv now applies to IPv6 prefixes as specified in RFC6303 - this
is significantly friendlier to upstream servers.
CNAME fix in auth mode - A domain can only have a CNAME if it has no
other records
Drop 2 patches now included upstream.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
- Fix eap test to work with standalone hostapd builds
- Fix 11n test to check the correct define
- Add 11ac, 11r and 11w tests
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
New test release (since test1) includes 2 LEDE patches that are
upstream and may be dropped, along with many spelling fixes.
Add forthcoming 2017 root zone trust anchor to trust-anchors.conf.
Backport 2 patches that just missed test3:
Reduce logspam of those domains handled locally 'local addresses only'
Implement RFC-6842 (Client-ids in DHCP replies)
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This update includes numerous small fixes for:
1) Interfaces setup
2) Packets parsing
3) Sending replies
Without this there were multiple problems with exchanging information
between (u)mdns and other implementations (including (u)mdns as well).
This also follows project rename to umdns which was required to avoid
confusion with Apple's mdnsd from mDNSResponder project.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
as we do for IPv4 PPP interfaces. When we create the
dynamic IPv6 interface we should inherit ip6table from
main interface.
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
pppoe-discovery performs the same discovery process as pppoe, but does
not initiate a session
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
f107656 netifd: Add option to configure locktime for each device
cdc0e80 interface: add prefix assignment priority support
6397f5e device: add veth support
6228d0f wireless: fix _wireless_add_process
7cc2f10 treewide: fix white space errors
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The only HMACs currently available use MD5 and SHA1, both of which have known
weaknesses. We already compile in the SHA256 code since we use Curve25519
by default, so there's no significant size penalty to enabling this.
Signed-off-by: Joseph C. Sible <josephcsible@users.noreply.github.com>
Bump to dnsmasq 2.77test1 - this includes a number of fixes since 2.76
and allows dropping of 2 LEDE carried patches.
Notable fix in rrfilter code when talking to Nominum's DNS servers
especially with DNSSEC.
A patch to switch dnsmasq back to 'soft fail' for SERVFAIL responses
from dns servers is also included. This mean dnsmasq tries all
configured servers before giving up.
A 'localise queries' enhancement has also been backported (it will
appear in test2/rc'n') this is especially important if using the
recently imported to LEDE 'use dnsmasq standalone' feature 9525743c
I have been following dnsmasq HEAD ever since 2.76 release.
Compile & Run tested: ar71xx, Archer C7 v2
Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ref commit 9525743c07
dnsmasq: make DHCPv6 viable for standalone dnsmasq install
Above commit broke instancing by missing filter_dnsmasq()
as part of the dhcp_add() execution.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Do not spam the syslog with DHCPv6 lease info if quietdhcp option
is selected. This already works for DHCPv4, make it work in the same
way for DHCPv6.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
[Originally written by Arjen de Korte on GitHub but had issues providing
a SoB in correct format.]
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
key_direction shows up as an openvpn option in the user-interface but does not end up in the /var/etc/openvpn*.conf file. Adding it to the list here fixed the issue for me.
Signed-off-by: Brandon Koepke <bdkoepke@fastmail.com>
samba.org has started to enforce https and
currently plain http downloads with curl/wget fail,
so convert samba.org download links to use https.
Modernise links at the same time.
Also convert samba.org URL fields to have https.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
dnsmasq has sufficient services to meet the needs of DHCP
and RA with IP6 for single router router users. This is
the most common use for consumer routers. Its reenforced
as most ISP tend to only DHCP-PD /64. dnsmasq has year
over year demonstrated great flexibility in its option
set, and support for off-standard DHCP clients.
odhcpd has enhanced capabilities focused on IP6 such
as DHCP/RA relay and NDP proxy. However, it is not as
flexible in its option set. odhcpd is not as forgiving
with off-standard DHCP clients. Some points may represent
a long term TODO list, but it is the state currently.
These changes make any such combination possible. Already
odhcpd can be set as the main dhcp server. Now odhcpd
can be removed or disabled and dnsmasq will take over
if DHCPv6 compiled in. The existing DHCPv6 and RA UCI
are translated into dnsmasq.conf. The changes focus on
'--dhcp-range', '--dhcp-host', and '--dhcp-options'.
DHCP host ID is least 16 bits [::1000-::FFFF], but
leaves low range for typical infrastructure assignments.
dnsmasq accepts DHCPv6 options in the tranditional
'--dhcp-option' put they must be prefixed 'option6:'.
dnsmasq will also discover SLAAC DNS entries from DHCPv4
clients MAC, and confirm with a ping at least renew.
Long term TODO include improving use of dnsmasq relay
options for DHCPv4 and DHCPv6 in parallel. It would also
be possible to preconfigure DHCP-PD in host-with-options
records for fixed infrastructure.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
[Jo-Philipp Wich: emit proper IPv6 hostid format in dhcp-host directive]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ref commit 612e2276b4
ref commit ec63e3bf13
'option add_local_hostname' scripted implementation statically assigns
this host in auto generated host file at init. If IFUP or other signals
do not occur, then address changes are not tracked. The script doesn't
apply all the addresses at an interface. This may make logs obscure.
The script only puts the bare host name (maybe not FQDN) in host file,
but if '--exapandhosts' is enabled, then /etc/hosts entries will be
suffixed, and "127.0.0.1 localhost" becomes "localhost.lan".
dnsmasq provides an option to perform this function, but it is rather
greedy. '--interface-name=<name>,<iface>' will assign the name to all
IP on the specified interface (except link local). This is a useful
feature, but some setups depend on the original restrictive behavior.
'option add_local_fqdn' is added to enhance the feature set, but
if not entered or empty string, then it will default to original
option and behavior. This new option has a few settings. At each
increased setting the most detailed name becomes the PTR record:
0 - same as add_local_hostname 0 or disabled
1 - same as add_local_hostname 1
2 - assigns the bare host name to all IP w/ --dnsmasq-interface
3 - assigns the FQDN and host to all IP w/ --dnsmasq-interface
4 - assigns <iface>.<host>.<domain> and above w/ --dnsmasq-nterface
'option add_wan_fqdn' is added to run the same procedure on
inferred WAN intefaces. If an interface has 'config dhcp' and
'option ignore 1' set, then it is considered WAN. The original
option would only run on DHCP serving interfaces.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
This will allow starting hostapd with the new -s parameter and finally
read all (error) messages from the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
c13b6a0 dhcpv6: fix white space error
e9d80cc dhcpv6: trigger restart of DHCPv6 state machine when not
receiving statefull options
c7122ec update README
419fb63 dhcpv6: server unicast option support
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
It wasn't possible to read hostapd wpa_printf messages unless running
hostapd manually. It was because hostapd was printing them using vprintf
and not directly to the syslog.
We were trying to workaround this problem by redirecting STDIN_FILENO
and STDOUT_FILENO but it was working only for the initialization phase.
As soon as hostapd did os_daemonize our solution stopped working.
Please note despite the subject this change doesn't affect debug level
messages only but just everything printed by hostapd with wpa_printf
including MSG_ERROR-s. This makes it even more important as reading
error messages can be quite useful for debugging.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Updates to openvpn.init were included in early OpenVPN 2.4 patch
series, but got lost along the way and were never merged.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
When relying on x.509 certs for auth and / or encryption of traffic you can't
use package openvpn-nossl.
Just have your package depend on openvpn-crypto to have SSL-encryption and
X.509-support enabled in OpenVPN. If encryption / X.509 is not a must, use
virtual packge openvpn, which is provided by all OpenVPN-variants.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
ap_setup_locked is named wps_ap_setup_locked in uci for consistency with other
wps related uci options.
Signed-off-by: Steven Honson <steven@honson.id.au>
The hostapd_append_wpa_key_mgmt() procedure uses the possibly uninitialized
$ieee80211r and $ieee80211w variables in a numerical comparisation, leading
to stray "netifd: radio0 (0000): sh: out of range" errors in logread when
WPA-PSK security is enabled.
Ensure that those variables are substituted with a default value in order to
avoid emitting this (harmless) shell error.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add PROVIDES:=openvpn to the default recipe in order to let all build variants
provide a virtual openvpn package.
The advantage of this approach is that downstream packages can depend on just
"openvpn" without having to require a specific flavor.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Packets which are merely forwarded by the router and which are neither
involved in any DNAT/SNAT nor originate locally, are considered INVALID
from a conntrack point of view, causing them to get dropped in the
zone_*_dest_ACCEPT chains, since those only allow stream with state NEW
or UNTRACKED.
Remove the ctstate restriction on dest accept chains to properly pass-
through unrelated 3rd party traffic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use ubus process signalling instead of 'kill pidof dnsmasq' for
SIGHUP signalling to dnsmasq when ntp says time is valid.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This causes problem when a FQDN is configured in /etc/config/system. The
domain name will appear twice in reverse DNS.
Next to that, there seems to be a bug in dnsmasq. From the manual page:
--interface-name=<name>,<interface>[/4|/6]
Return a DNS record associating the name with the primary address
on the given interface. This flag specifies an A or AAAA record for the
given name in the same way as an /etc/hosts line, except that the address
is not constant, but taken from the given interface. The interface may be
followed by "/4" or "/6" to specify that only IPv4 or IPv6 addresses
of the interface should be used. If the interface is down, not configured
or non-existent, an empty record is returned. The matching PTR record is
also created, mapping the interface address to the name. More than one name
may be associated with an interface address by repeating the flag; in that
case the first instance is used for the reverse address-to-name mapping.
It does not just create an A/AAAA record for the primary address, it creates
one for all addresses. And what is worse, it seems to actually resolve to the
non-primary address first. This is quite annoying when you use floating IP
addresses (e.g. VRRP), because when the floating IP is on the other device,
SSH failes due to incorrect entry in the known hosts file.
I know that this is not a common setup, but it would be nice if there was an
option to restore the previous behaviour, rather than just forcing this new
feature on everybody.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Delete the map-t device when tearing down the map-t interface; as such
there's no conflict when the map-t interface comes up again when trying
to add the map-t device as the map-t device was still present
(Can not add: device 'map-wan6_4' already exists!).
Only call ifdown in teardown for map-e and lw6o4 map interfaces types
in order to suppress the trace "wan6_4 (6652): Interface wan6_4_ not found"
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts the following commits:
fbe522d120278ad007ee863888e44f96daf6352fcfd83555fc
This seems to trigger some mconf bugs when built with all feeds
packages, so I will try to find a less intrusive solution before the
release.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
wpa_supplicant allows only SAE as the key management
type for mesh mode. The recent key_mgmt rework unconditionally
added WPA-PSK - this breaks interface bringup and wpa_s
throws this error message:
Line 10: key_mgmt for mesh network should be open or SAE
Line 10: failed to parse network block.
Failed to read or parse configuration '/var/run/wpa_supplicant-wlan0.conf
Fix this by making sure that only SAE is used for mesh.
Signed-off-by: Sujith Manoharan <m.sujith@gmail.com>
Enabling this makes it possible to query LLDP neighbors via SNMP.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Add option keep_ra_dnslifetime which will preserve the received
lifetime for RDNSS and DNSSL RA records and not overwrite it
by the RA router lifetime as specified in RFC6106.
This allows to accept RDNNS records from RAs that don't announce
a default route by setting router lifetime to 0 in the RAs.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
ef3c563 dhcpv6-ia: filter out prefixes having invalid length
16cd87e dhcpv6-ia: fix dereference after freeing assignment
d6b0c99 dhcpv6-ia: log only IPv6 addresses which are effectively
assigned to a DHCPv6 client
08a9367 config: respect ignore uci option
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
'add_local_hostname' previous implementation may drop some addresses.
Soft addition of IP6 addresses may not cause a reload or restart event.
dnsmasq '--interface-name' robustly applies DNS to all addresses per
interface (except fe80::/10).
Change UCI 'add_local_hostname' to expand during each interface assignement
during add_dhcp().
Assign '<iface>.<host>.<domain>' as true name (reflexive A, AAAA, and PTR).
Assign '<host>.<domain>' and '<host>' as convinience aliases (no PTR, not
technically CNAME).
This is accomplished with the '--interface-name' order, first is PTR.
We could also assign each <ip4/6>.<iface>.<host>.<domain> to the respective
dual stack on the interface.
That seemed excessive so it was skipped (/4 or /6 suffix to the interface).
Add UCI 'add_wan_hostname' similar to 'add_local_hostname' function for
external WAN.
WAN IP4 are less often named by the ISP and rarely WAN IP6 due to complexity.
For logs, LuCI connection graph, and other uses assigning a WAN name is desired.
'add_local_hostname' only applies with DHCP and 'add_wam_hostname' only applies
without DHCP. Common residential users will want to set both options TRUE.
Businesses will probably have global DNS, static IP, and 'add_wan_hostname' FALSE.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Add DHCPv6 matching by DHCP Unique Identifier (RFC-3315) in addition to
existing MAC-address (RFC-6939). The latter is not widely supported yet.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
Enable support for stronger SHA256-based algorithms in hostapd and
wpa_supplicant when using WPA-EAP or WPA-PSK with 802.11w enabled.
We cannot unconditionally enable it, as it requires hostapd to be
compiled with 802.11w support, which is disabled in the -mini variants.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Now that wpa_key_mgmt handling for hostapd and wpa_supplicant are
consistent, we can move parts of it to a dedicated function.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Rework wpa_key_mgmt handling for wpa_supplicant to be consistent with
how it is done for hostapd.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
This commit modifies the /lib/netifd/proto/gre.sh script so that, when
GRE-TAP tunnels are created, either IPv4 or IPv6, the prefix before the chosen
interface name contains the "tap" substring, to differentiate them from non-TAP
GRE tunnels.
Right now, both GRE and GRE-TAP tunnel (either IPv4 or IPv6) interfaces defined
in /etc/config/network are named equally ("gre-"+$ifname or "grev6"+$ifname)
upon creation. For instance, the following tunnels:
config interface 'tuna'
option peeraddr '172.30.22.1'
option proto 'gre'
config interface 'tunb'
option peeraddr '192.168.233.4'
option proto 'gretap'
config interface 'tunc'
option peer6addr 'fdc5:7c9e:e93d:45af::1'
option proto 'grev6'
config interface 'tund'
option peer6addr 'fdc0:6071:1348:31ff::2'
option proto 'grev6tap'
are named, respectively, "gre-tuna", "gre-tunb", "grev6-tunc" and "grev6-tund".
The current change makes that each GRE tunnel interface of the four different
types available (gre, gretap, grev6 and grev6tap) gets a different prefix.
Therefore, the abovementioned tunnels will be named, respectively:
"gre4-tuna", "gre4t-tunb", "gre6-tunc" and "gre6t-tund".
This is coherent with other types of virtual interfaces (i.e. PPP, PPPoE, PPPoA)
where the whole protocol name is used. For instance, a PPPoA interface named
"p1" and a PPPoE interface named "p2" will respectively appear as "pppoa-p1"
and "pppoe-p2", not as "ppp-p1" and "ppp-p2").
Since Linux interfaces names are limited to 15 characters, these prefixes leave,
for the worst case (TAP tunnels), 9 characters for the actual name.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This fixes the folowing security problems:
CVE-2016-9586: printf floating point buffer overflow
CVE-2016-9952: Win CE schannel cert wildcard matches too much
CVE-2016-9953: Win CE schannel cert name out of buffer read
CVE-2016-9594: unititialized random
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
64a655d proto: allow configuring deprecated static IPv6 addresses
c99182e remove obsolete /opt/local prefix on Mac OS X
0249d5f system-linux: Don't set gre tunnel ttl by default to 64 (#FS312)
edc15ca ubus: Display the IPv6 prefix assigned address
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
add possibility to set the facility to which dnsmasq will send syslog entries, i.e. set it to '/dev/null' to mute dnsmasq output at all.
Signed-off-by: Dirk Brenken dev@brenken.org
Before the rewrite, uhttpd-mod-tls used to contain a tls plugin.
Afterwards it was left in for compatibility reasons, but given how much
has changed, and that we're about to change the default SSL
implementation again, it's better to just drop this now
Signed-off-by: Felix Fietkau <nbd@nbd.name>
OpenVPN 2.4 builds with mbedTLS 2.x, rename openvpn-polarssl
variant to openvpn-mbedtls.
Some feature highlights:
* Data channel cipher negotiation
* AEAD cipher support for data channel encryption (currently only
* AES-GCM)
* ECDH key exchange for control channel
* LZ4 compression support
See https://github.com/OpenVPN/openvpn/blob/master/Changes.rst
for additional change notes.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Build seems to fail with:
```
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies for X:
* grev4 *
* opkg_install_cmd: Cannot install package X
```
After adding an empty install rule, the failure goes away.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
uqmi has the possibility to allow the modem to start a regsitration
process only to this specified plmn
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Let dnsmasq reread the leasefile by using procd_send_signal
which triggers procd to send SIGHUP kill signal by default
if signal is not specified
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to latest upstream HEAD:
- Refreshed all
- Delete patches and parts which made it upstream
Compile tested Full & Mini configs
Run-tested Mini config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [another update, remove broken patch]
Update tc to track upstream cake changes:
diffserv3 - a simple 3 tin classifier
Also make diffserv3 and triple-isolate default
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Add uqmi 'sync' command call to release stalled cid when preparing to
setup new connection. As a result it prevents 'POLICY MISMATCH' errors.
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
8ceeab6 uqmi: Change returned value to QMI_CMD_REQUEST for 'sync' command.
1dc7be1 uqmi: Add sync command to release all cids.
Signed-off-by: John Crispin <john@phrozen.org>
It's useful when using multiple usb devices that should be bound to
certain usb ports. Symlinks are created by hotplug handlers.
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
It's useful when using multiple usb devices that should be bound to
certain usb ports. Symlinks are created by hotplug handlers.
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
The build system only accepts Package/<name>/description and since the
typoed version virtually has the same content as the TITLE field, remove
them altogether
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The SIGHUP also got sent to the reload script making it bail out
with an error
Revert "dnsmasq: reload config if host name is modified"
This reverts commit 854459a2f9.
Reported-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
The sha256sum was not updated in the last commit.
Fixes: a7c231027 [odhcpd: Fix dnsmasq re-reading hostfile]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for specifying a call profile index instead of APN. A
specific index different from 1 must be used for some service
provider and modem combinations.
In addition, change the manufacturer detection to use the standard
AT+CGMI command, which produces more predictable output than ATI,
remove the redundant ipv6 option, since it is less ambiguous to
directly specify the PDP context type with mobile connections, and
fix missing device during teardown when using ncm through the wwan
proto.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
Update uqmi to latest version, which brings about support for
specifying a call profile index instead of APN. A specific index
different from 1 must be used for some service provider and modem
combinations.
Also change option dhcp to dhcpv6, since IPv4 now always uses DHCP,
replace option ipv6 with pdptype, which is less ambiguous, and
make autoconnect optional and default it to off for IPv6 due to it
not working with statically configured IPv6.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
Harmonise handling of DEFAULT_PATH by removing the patch introducing #ifndef
guards around the path, and only using one means to set the path in the
makefile.
Signed-off-by: Dario Ernst <Dario.Ernst@riverbed.com>
The xt_id match was used by the firewall3 package to track its own rules but
the approach has been changed to use xt_comment instead now, so we can drop
this nonstandard extension.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to current HEAD in order to drop automatic generation of per-zone
NOTRACK rules.
The NOTRACK rules used to provide a little performance improvement but the
later introduction of the netfilter conntrack cache made those rules largely
unnecessary. Additionally, those rules caused various issues which broke
stateful firewalling in some scenarios.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Depending on the dhcp uci config pidof dnsmasq can return
multiple pids. Fix re-reading of the hostfile by dnsmasq in
such case by sending SIGHUP signal to each of the returned
pids.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Let dnsmasq read all hosts files in /tmp/hosts directory by specifying
/tmp/hosts as argument of --addn-host
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Support new packet overhead passing paradigm in cake qdisc, also restore
DSCP wash/nowash keywords.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
OpenVPN requires arguments to --push to be enclosed in double quotes.
One set of quotes is stripped when the UCI config is parsed.
Change append_params() of openvpn.init to enclose push parameters in
double quotes.
Unquoted push parameters do not cause errors in OpenVPN 2.3,
but OpenVPN 2.4 fails to start with unquoted push parameters.
Fixes: FS#290.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Correct splitting the 32-bit 'hostid' value to two 16-bit hexadecimal
values. Previously, the lower 16-bit value was truncated to an 8-bit
value, which would result in hostid values 100 and 200 both to be set
to [::0:0] instead of [::0:100] and [::0:200] respectively.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
If the hostname in /etc/config/system is modified the dnsmasq will not
reread the update host file under /tmp/hosts/dhcp.$cfg.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
This fixes the following security problems:
CVE-2016-8615: cookie injection for other servers
CVE-2016-8616: case insensitive password comparison
CVE-2016-8617: OOB write via unchecked multiplication
CVE-2016-8618: double-free in curl_maprintf
CVE-2016-8619: double-free in krb5 code
CVE-2016-8620: glob parser write/read out of bounds
CVE-2016-8621: curl_getdate read out of bounds
CVE-2016-8622: URL unescape heap overflow via integer truncation
CVE-2016-8623: Use-after-free via shared cookies
CVE-2016-8624: invalid URL parsing with '#'
CVE-2016-8625: IDNA 2003 makes curl use wrong host
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Not all kmod packages depends on kmod-ipt-compat-xtables, but this
kernel config option is required for building the whole package
Signed-off-by: Felix Fietkau <nbd@nbd.name>
odhcpd daemon has hitless config reload support by means of the
sighup signal; add reload_service function which uses sighup
signal to reload the config
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This fixes building with musl and drops the dependency on the OpenWrt
kernel-header patches:
270-uapi-kernel.h-glibc-specific-inclusion-of-sysinfo.h.patch
271-uapi-libc-compat.h-do-not-rely-on-__GLIBC__.patch
272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch
Use the new upstream location at netfilter.org and use a define instead
of a patch to "optimize".
See also: https://git.netfilter.org/arptables/log/
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
[Jo-Philipp Wich: add mirror SHA256 sum]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds support for "channels" command which displays more details
about channels. It includes e.g. info about available widths.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Update to latest Git head in order to import several fixes and enhancements.
- Disable drop invalid by default (FS#73, FS#154)
Instead of dropping packets with conntrack state INVALID, only allow streams
with explicit NEW or UNTRACKED conntrack state.
This change gives user defined rules the chance to accept traffic like ICMPv6
multicast which would be filtered away by the very early ctstate INVALID drop
rule otherwise.
The old behaviour can be restored by explicitely setting "drop_invalid" to 1
in the global firewall config section.
- Fix re-initialization of loadable iptables extensions on musl (FS#31)
Since musl does not implement actual dlclose() semantics, it is impossible to
re-run initializers on subsequent dlopen() calls.
The firewall3 executable now intercepts the extension registration calls
instead in order to be able to re-call them when needed.
This also allowed us to switch to libxtables' builtin extension loader as a
positive side-effect.
- Fix masquerade rules for multiple negated IP addresses (FS#248)
When building MASQUERADE rules for zones which specify multiple negated
addresses in masq_src or masq_dest, emit -j RETURN rules which jump out of
the masquerading chain instead of creating multiple rules with inverted "-s"
arguments.
- Tag own rules using comments
Instead of relying on the nonstandard xt_id match, use the xt_comment match
to mark own rules. Existing comments are prefixed with "!fw3: " while
uncommented rules are marked with a sole "!fw3" string.
This allows removing the xt_id match entirely in a later commit.
- Make missing ubus connection nonfatal
Technically, firewall3 is able to operate without ubus just fine as long as
the zones are declared using "option device" or "option subnet" instead of
"option network" so do not abort execution if ubus could not be connected or
of no network namespace is exported in ubus.
This allows running firewall3 on ordinary Linux systems.
- Fix conntrack requirement detection for indirectly connected zones
The current code fails to apply the conntrack requirement flag recursively to
zones, leading to stray NOTRACK rules which break conntrack based traffic
policing.
Change the implementation to iteratively reapply the conntrack fixup logic
until no more zones had been changed in order to ensure that all directly and
indirectly connected zones receive the conntrack requirement flag.
- Add support for iptables 1.6.x
Adds support for the xtables version 11 api in order to allow building
against iptables 1.6.x
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
"This release fixes a few minor bugs, including a
(non-security-impacting) buffer overflow fix ported
from upstream cjson."
<http://software.es.net/iperf/news.html#iperf-3-1-4-released>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds the mac address of the DNS requestor to DNS queries which
are forwarded upstream and can be used to do filtering by the
upstream servers. This only works if the requestor is on the
same subnet as the dnsmasq server
The addmac parameter can hold the following values:
0 : mac address is not added
1 : mac address is added in binary format
base64 : mac address is added base64 encoded
text: : mac address is added in human readable format
as hex and colons
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
moving comgt and its modules to WWAN submenu to join uqmi as both are tools for WWAN modems.
I replaced the link with comgt's ubuntu manpage because the old link isn't working anymore.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
For Huawei devices like E3372 proper command for set lte mode is:
AT^SYSCFGEX="03",3fffffff,2,4,7fffffffffffffff,,
Eval is required for proper quotation.
Without this fix:
Fri Nov 4 19:07:49 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 4 19:07:52 2016 daemon.notice netifd: wan (2060): sending -> AT
Fri Nov 4 19:07:52 2016 daemon.notice netifd: wan (2060): sending -> ATZ
Fri Nov 4 19:07:53 2016 daemon.notice netifd: wan (2060): sending -> ATQ0
Fri Nov 4 19:07:53 2016 daemon.notice netifd: wan (2060): sending -> ATV1
Fri Nov 4 19:07:54 2016 daemon.notice netifd: wan (2060): sending -> ATE1
Fri Nov 4 19:07:55 2016 daemon.notice netifd: wan (2060): sending -> ATS0=0
Fri Nov 4 19:07:55 2016 daemon.notice netifd: wan (2060): sending -> AT+CGDCONT=1,"IP","internet"
Fri Nov 4 19:07:57 2016 daemon.notice netifd: wan (2060): sending -> AT^SYSCFGEX=\"03\",3fffffff,2,4,7fffffffffffffff,,
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2060): Error running AT-command
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2060): Failed to set operating mode
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2092): Stopping network
...
With this fix:
Fri Nov 4 19:10:59 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 4 19:11:01 2016 daemon.notice netifd: wan (2539): sending -> AT
Fri Nov 4 19:11:01 2016 daemon.notice netifd: wan (2539): sending -> ATZ
Fri Nov 4 19:11:02 2016 daemon.notice netifd: wan (2539): sending -> ATQ0
Fri Nov 4 19:11:03 2016 daemon.notice netifd: wan (2539): sending -> ATV1
Fri Nov 4 19:11:03 2016 daemon.notice netifd: wan (2539): sending -> ATE1
Fri Nov 4 19:11:04 2016 daemon.notice netifd: wan (2539): sending -> ATS0=0
Fri Nov 4 19:11:05 2016 daemon.notice netifd: wan (2539): sending -> AT+CGDCONT=1,"IP","internet"
Fri Nov 4 19:11:06 2016 daemon.notice netifd: wan (2539): sending -> AT^SYSCFGEX="03",3fffffff,2,4,7fffffffffffffff,,
Fri Nov 4 19:11:07 2016 daemon.notice netifd: wan (2539): sending -> AT^NDISDUP=1,1,"internet"
Fri Nov 4 19:11:08 2016 daemon.notice netifd: wan (2539): Connected, starting DHCP on wwan0
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan' is now up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Network device 'wwan0' link is up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Network alias 'wwan0' link is up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' is enabled
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' has link connectivity
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' is setting up now
...
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Rename the "ip" package declaration to "ip-tiny" and let both "ip-tiny" and
"ip-full" provide the virtual "ip" package. This allows users to freely choose
the "ip" command variant while other packages can continue to depend on "ip"
without needing to enforce a specific variant.
Note that this commit does not add busybox as "ip" provider due to
the following reasons:
- The builtin Busybox ip applet cannot be added or removed at runtime
- Both "ip-tiny" and "ip-full" are able to install without file clashes even
if the busybox applet is enabled
- The system is preferring full "ip-tiny" and "ip-full" at runtime, even
if Busybox ip is still present.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Ensure that selecting the wpa-supplicant-mesh package actually packages the
wpa_supplicant binary with SAE support and add missing dependency on OpenSSL.
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: slightly reword commit message for clarity]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We add an 'httpauth' section type that contains the options:
prefix: What virtual or real URL is being protected
username: The username for the Basic Auth dialogue
password: Hashed (crypt()) or plaintext password for the Basic Auth dialogue
httpauth section names are given included as list
items to the instances to which they are to be applied.
Further any existing httpd.conf file (really whatever
is configured in the instance, but default of
/etc/httpd.conf) is appended to the per-instance httpd.conf
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
During reload, we could send invalid information to the other
side and confuse it.
That's why, during reload we'll pause execution, do the reconfig
and resume + update when reload is done.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The problem is that interfaces are specified at start as
command line arguments, making them unchange-able via reload.
That means, we have to move (since lldpd allows this) the
interfaces-match-pattern option to be in a config file and reload
the configuration.
It's either that, or do a 'restart'.
Since we're generating the lldpd.conf file, we'll have to
move the 'sysconfdir' of lldpd to /tmp, where the files will
get written ; this will prevent any unncessary flash writes.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Adds support in uci for configuring multiple dnsmasq instances via
multiple dnsmasq sections.
The uci sections host, boot, mac, tag, vendorclass, userclass,
circuitid, ... will refer to a dnsmasq instance via the instance
parameter defined in the section; if the instance parameter is
not specified backwards compatibility is preserved.
Start/Stopping a dnsmasq instance can be achieved by passing the
dnsmasq instance name as argument to start/stop via the init script.
Multiple dnsmasq instances is usefull in scenarios where you want to
bind a dnsmasq instance to an interface in order to isolate networks.
This patch is a rework of a multiple dnsmasq instance patch by Daniel Dickinson
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add a partially random O= item to the certificate subject in order
to make the automatically generated certificates' subjects unique.
Firefox has problems when several self-signed certificates
with CA:true attribute and identical subjects have been
seen (and stored) by the browser. Reference to upstream bugs:
https://bugzilla.mozilla.org/show_bug.cgi?id=1147544https://bugzilla.mozilla.org/show_bug.cgi?id=1056341https://bugzilla.redhat.com/show_bug.cgi?id=1204670#c34
Certificates created by the OpenSSL one-liner fall into that category.
Avoid identical certificate subjects by including a new 'O=' item
with CommonName + a random part (8 chars). Example:
/CN=LEDE/O=LEDEb986be0b/L=Unknown/ST=Somewhere/C=ZZ
That ensures that the browser properly sees the accumulating
certificates as separate items and does not spend time
trying to form a trust chain from them.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prefer the old default 'px5g' for certificate creation
as Firefox seems to dislike OpenSSL-created certs.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This option, defined by RFC3442, allows a DHCP server to send static
routes to a client. But the client has to request this option
explicitely.
Static routes are useful when the gateway configured by DHCP cannot be
in the same subnet as the client. This happens, for instance, when
using DHCP to hand out addresses in /32 subnets.
A new configuration option "classlessroute" is available, allowing
users to disable this feature (the option defaults to true).
Other DHCP clients already request this option by default (dhcpcd, for
instance, and possibly Windows). If a DHCP server does not support
this option, it will simply ignore it.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
The special prefix of "/" should match any url by definition but the final
assertion which ensures that the matched prefix ends in '\0' or '/' is causing
matches against the "/" prefix to fail.
Update to current HEAD in order to fix this particular case.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
iperf upstream added some bugfixes to the already released 2.0.9 version
without changing the filename. This conflicts with old mirrored files
and the hash that we previously used.
To avoid conflict, use a renamed tarball from mirror2.openwrt.org
containing the new upstream changes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This more of a demo for the previous commit that comes with
this one, where I added support for copying source from 'src' to
the build dir(s).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Adds per-host leasetime support
Various bugfixes :
-Prioritize ifname resolving via ubus
-Free interface if ifindex cannot be resolved
-...
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [update mirror sha256]
Commit 8f24ee6382 ("uqmi: Add proper IPv6 support") changed the code
to fetch the IPv4 address via QMI by default instead of using DHCP to
make it consistent with the IPv6 codepath.
This breaks on at least some Sierra Wireless cards, where data exchanges
fail to work until the host has fetched a DHCP lease.
Leave v6 as it is, but always use DHCP for v4.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Quote resolveip hostname argument to avoid bad shell injections.
While at it fix pattern match logic in case multiple IPv6 addresses
are returned for a hostname as they're seperated by newline by
resolveip and not a white space
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Now that the uhttpd init script can generate certificates using openssl as
well, update the section name and related comment to be more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support the usage of the OpenSSL command-line tool for generating
the SSL certificate for uhttpd. Traditionally 'px5g' based on
PolarSSL (or mbedTLS in LEDE), has been used for the creation.
uhttpd init script is enhanced by adding detection of an installed
openssl command-line binary (provided by 'openssl-util' package),
and if found, the tool is used for certificate generation.
Note: After this patch the script prefers to use the OpenSSL tool
if both it and px5g are installed.
This enables creating a truly OpenSSL-only version of LuCI
without dependency to PolarSSL/mbedTLS based px5g.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Fix rt_names build failure when FORTIFY_SOURCE disabled.
Include limits.h which otherwise gets automatically included
by fortify headers.
Solves FS #194
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Within the Lua binding, use the same logic as the command line interface for
reporting the used WPA ciphers. Instead of printing the intersection of
pairwise and group ciphers, report both group and pairwise ciphers.
This fixes a case where a connection which uses CCMP for pairwise and TKIP
as groupwise cipher is getting reported as using the NONE cipher.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Remove an invalid local variable declaration in the tunnel update subshell
invocation. Local declarations outside of function scopes are illegal since
the Busybox update to version 1.25.0 .
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Configurations without shadow passwords have been broken since the removal
of telnet: as the default entry in /etc/passwd is not empty (but rather
unset), there will be no way to log onto such a system by default. As
disabling shadow passwords is not useful anyways, remove this configuration
option.
The config symbol is kept (for a while), as packages from feeds depend on
it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Match sections allow to set a tag specified by the option networkid if the client
sends an option and optionally the option value specified by the match option.
The force option will convert the dhcp-option to force-dhcp-option if set to 1 in
the dnsmasq config if options are specified in the dhcp_option option.
config match
option networkid tag
option match 12,myhost
option force 1
list dhcp_option '3,192.168.1.1'
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Permit users of the full variant to disable the NO_ID *.bind pseudo
domain masking.
Defaulted 'on' in all variants.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
As security precaution and to limit the attack surface based on
the version reported by tools like nmap mask out the dropbear
version so the version is not visible anymore by snooping on the
wire. Version is still visible by 'dropbear -V'
Based on a patch by Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove trailing _]
Don't expose dnsmasq version & other data to clients via the *.bind
pseudo domain. This uses a new 'NO_ID' compile time option which has been
discussed and submitted upstream.
This is an alternate to replacing version with 'unknown' which affects
the version reported to syslog and 'dnsmasq --version'
Run time tested with & without NO_ID on Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
