This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42126
Add the required nodes to the dtsi files and code to prevent double
registration from the board support code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42123
In preparation for switching to dtb based board identification, add
support for building lzma-loader and lzma cfe kernels with dtb
appended.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42121
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42119
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42088
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42083
In r41578 this was added in order to make default images bootable for the BB
release. We need more generic approach for this.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42071
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 42023
Created on basis of 3.10 config. Remove few obsolete symbols and add new
upstream symbols. New symbols left in its default state.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41996
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
SVN-Revision: 41993
Fix IFF_NO_IP_ALIGN location which is collide with new netdev private flag
IFF_MACVLAN.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41992
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
SVN-Revision: 41961
This commit implements a new netfilter match "xt_id" which can be used to
attach unsigned 32bit IDs to iptables rules.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41945
Mostly works except for USB led. Flashing not tested yet. Mostly
as an example for the sprom fixup code.
Fixup values taken from GPL tarball by comparing bcm43217_map.c
with the struct in sprom.c.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41944
Rework fallback sprom support by providing different sproms for
different chips. Also make it optional to use.
This likely causes sprom fallback support to break on a few boards.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41942
Now that BB is branched off, we can now switch to 3.14 and start
breaking stuff again.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41941
Add a working lzma loader and use it for generating initramfs kernels
to allow easily netbooting elf kernels on devices with a 4 MiB CFE
size limit.
Based on ar71xx's lzma-loader.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41940
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41939
This patch adds support for setting SPI_CS1 as Chip Select, Watchdog reset output and GPIO#27.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41938
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41932
without this the build for NBG6716 fails due to missing packages
https://dev.openwrt.org/ticket/17325
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41930
This is a backport of bcma from wireless-tesing/master tag master-2014-07-29-1.
For kernel < 3.10 this only adds the header changes needed by more
recent b43 versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41899
Fix a typo: gpio 21 is already used for the WPS led. Gpio 20 is the
right one (tested) for the mode switch. Confirmed that
/sys/kernel/debug/gpio state followed the position of the switch.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41858
Since kernel commit 928bea964827 ("PCI: Delay enabling bridges until
they're needed"), pci fixups are run with bridges (e.g. the pcie port)
disabled.
This causses hangs when ath9k_pci_fixup tries to manually enable the
device to apply the register fixups.
Fix this by enabling any parent bridges before trying to access the
device itself.
Fixes boot on DSL-274XB rev F1.
Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41856
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 41841
Compile tested all subtargets and profiles.
Unfortunately I don't own any board affected by these changes, so no run tests.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41839
The earlier r41797 change was missing this part, to enable the right
vlan configuration.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41838
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken. This seems to fix it.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41837
It doesn't seem to be used anywhere, it's incompatible with other
targets and can be confusing. People may think they need to update
section name every time they change VLAN ID (well, even I was doing
that).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41835
This is a backport of bcma and ssb from wireless-tesing/master tag
master-2014-07-22.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41804
The airGateway has a reset button connected to GPIO 12, so we should use it.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41794
ASL-26555 16MB: caldata is present on uboot-env and devdata, but the proper one seems to be the devdata, since mac address corresponds to Amper, the real manufacturer, meanwhile the caldata on uboot-env corresponds to D-Link.
ASL-26555 8MB: caldata is only present on uboot-env, but its mac address corresponds to Alpha, the real manufacturer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41768
The default case in 02_network is inappropriate for the MikroTik RouterBOARD 91x boards because they do not have a WAN port, so don't bother setting the non-existent eth1 interface as the WAN port.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41767
This patch adds support for the Ubiquiti Networks airGateway.
Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41766
Update the kernel of the orion target to version 3.10.44.
Refresh orion config and patches to match the changes in the kernel
Tested on WRT350N-v2 device.
Signed-off-by: Maarten Bezemer <maarten.bezemer@gmail.com>
[run make kernel_oldconfig, fold a01-dt2-fixes-for-3.3.patch into dt2-setup.c,
make dt2-setup.c compile, fix harddisk subprofile]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41765
This fixes error erasing partial mtd partition which does not start on
eraseblock boundary and allows using fconfig to configure redboot on
devices such as the Gateworks Cambria.
Signed-off-by: Maciej Skrzypek <maciej.skrzypek@flytronic.pl>
SVN-Revision: 41733
Declare inline placeholder when usb_hcd_amd_remote_wakeup_quirk() not
compiled due CONFIG_PCI_DISABLE_COMMON_QUIRKS.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41702
Use AR2315_ prefix for macroses specific to AR2315/AR2316/AR2317 chips,
use AR5312_ prefix for macroses specific to AR5312/AR2312/AR2313 chips,
and use AR231X_ prefix for common macroses.
This patch should not cause any functional changes, only make clear
which macros is common and which macros is specific.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41701
Pass only physical address to 8250 serial port driver and set flag to
remap I/O memory inside the driver. Also fix AR5312 UART base address
definition, which seems specified already mapped.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41700
Pass PHY I/O memory region via platform resources and remap them
unconditionally.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41698
Each SoCs generation has own independent gpiolib realization, so we
have no reason to keep these realizations in semiuniversal form.
Following modifications are made:
* Remove valid_mask field
* Remove ar231x_gpio_chip structure
* Rename AR2315_GPIO_CR to AR2315_GPIO_DIR
* Fix count of AR5312 GPIOs
* Simplify gpio_chip methods realization
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41696
Currently AR5312 misc IRQ numbers are used for AR2315+ chips, what cause
us to use switch-case to map IRQ number to ISR bit. Introduce AR2315
specific misc IRQs set and simplify interrupt (un)mask operation.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41694
Rename interrupt control handlers to be consistent with operation names
and add IRQ chips names.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41693
UART IRQ number could be different for different SoCs, so make them
configurable.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41691
* Pass iomem and IRQ via platform device resources
* Remap iomem and use iowrite32 accessor function
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41688
Rename config symbol to AR2315_WDT to avoid confusion with other Atheros
SoCs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41685
Move eeprom extraction from scripts to dts files.
Additionally there are few other changes like:
- whitespace fixes
- add partition labels where needed
- BR6524N board doesn't exist (lost in translation?)
- fix Edimax 3g-6200nl model
- add wmac eeprom to dts for Asus RT-N14U board
Compile tested all subtargets and their profiles.
Run tested on:
- Asus RT-N15
- Asus RT-N14U
- Buffalo WHR-600D
- Argus ATP52B
- Sparklan WCR-150GN
Few problems noted:
- many boards didn't have wmac eeprom information defined at all
- several boards don't have any patitions defined (see FIXME comments in dts)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41680
Some devices were renamed when converted from diag to in kernel board detection and it was not changed in netconfig. Devices not in the
kernel board detection are removed now.
This should close: #17111, #16968, #13202
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41663
The default case of ramips_setup_macs() is useful when mtd-mac-address is defined in dts.
But lan_mac is not set by default, this results in lan and wan having the same mac.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41632
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
- fix coding style,
- check the first and the last character of the MAC string
instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41622
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>
Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>
This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
- remove user-space and image generation support, will be included
from other patches,
- fix coding style and drop superfluous comment in mach-gl-inet.c,
- rename and refresh kernel patch,
- adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41618
The RB2011UiAS is almost exactly the same as the RB2011UAS, which is
already supported. Hardware-wise, it adds a passive power injector on
Eth10. Software-wise, Routerboot passes a different board name on the
kernel command line. Hence the need for a patch.
Not yet working:
* touchscreen: doesn't work on RB2011UAS either. The touchscreen itself
seems to be driven by an ADS7843-compatible IC, but figuring out which
GPIO pins it's connected to is work for the future.
* control of power injector: remains off. Probably also GPIO-controlled.
Signed-off-by: Soren Harward <stharward@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5841/
[juhosg: rename and refresh the kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41617
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41588
This patch also makes use of the new leds script.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41585
By using uci-defaults force_link is enabled, which fixes some link issues if ethernet cable isn't connected when LAN is initialized.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41583
Run lantiq_board_detect from lantiq_board_name and lantiq_board_model.
This was the one thing missing from r41474 for sysupgrade board
detection to work properly.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41567
Disables gluebi and enables ubiblock on lantiq xway. Squashfs
images on nand use ubifs instead of jffs2 for the overlay.
I'll leave the equivalent patch for xrx200 to someone who has a
board to test.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41565
With help of this script the ath10k board.bin settings are loaded from
flash and saved to the ath10k firmware directory. The driver reads it
later in the boot process.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41562
Since kernel 3.11, the third parameter passed to notifier_call()
is of type struct netdev_notifier_info. This patch fixes an oops
when setting a netdev LED trigger.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 41552
Move defines and board_info structs back to their proper locations so
(de-)selecting SOC support won't break the build.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41550
A reboot is issued by setting the watchdog timer to a low value, when
the value is decreased from 1 to 0 by the hardware the system will
reboot. Setting this value to 1 does not work every time, it is a
little bit more reliable when setting it to 3. This timer runs with
some MHz or KHz so nobody will notice the increased waiting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41548
broadcom-wl now builds in the mips74k profile, so remove these chips
from the generic profile.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41546
The previous attempt (r40717) to fix squashfx made the system bootable but
overlayfs remained broken.
This enables block2mtd again using the right partition number and naming
and adds MTD_ROOTFS_SPLIT option.
However onboard rootfs partition name had to be renamed to place overlay on
CF instead of onboard NAND.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41541
No config option should be set to m in the default config, because
there is also some script needed which picks the module up into the
image and that is missing this way. Always create a kmod when building
a module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41539
Most ar7 devices have only 16 MiB RAM, so select low_mem to give them
a chance to work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41532
When the Ethernet controller is powered down and someone wants to
access the mdio bus like the witch driver (b53) the system crashed if
PCI_D3hot was set before. This patch deactivates this power sawing mode
when a switch driver is in use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41527
According to the thread https://forum.openwrt.org/viewtopic.php?id=48281
b53 uses GPIO 7:
[ 4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7
and causes device to self-reboot. GPIO 8 was found in CFE boot log:
"Reset switch via GPIO 8 ..."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41526
Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41515
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41513
Without this patch the switch config for the adm switch did not worked,
because hey are not names eth0.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41512
This patch deactivates the statistics, adds a missing lock
initialization and fixes a waring.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41511
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.
Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41500
Realview is mostly used as a QEMU development platform, which will provide a
built-in DHCP server to NAT or bridge the connection outside of the emulated
environment.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 41495
This is not needed since our toolchain produces the expected binaries for the
target CPU.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 41494
New make target in lantiq to use UbinizeImage and SysupgradeNand.
Only enabled for BTHOMEHUBV2B for the moment but should be useable
for other lantiq nand boards.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41474
After r41444 wifi working on WRTnode. Tested.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41452
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget.
These drivers are not needed for ASE, Danube and AR9.
As side effect PHY11G and PHY22F firmwares are not included in the
kernel image, which saves 64 KB.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41449
The Livebox 1 support is currently broken. Fixed with this patch
Fixes:
- Redboot partitioning broken: fixed
- Replaced custom ephy reset with platform code
- USB code breaks the building process: fixed
- Led colors
- Removed unneded EHCI code since bcm6348 only has OHCI
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: drop unneded parts since merge, fixup to apply to current head]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41424
This adds support for Comtrend WAP-5813n.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41421
Some fixes for Telsey CPVA502+ bcm6348 routers:
- reset the external PHY (eth1) with proper platform code, not using a led definiton
- eth1 is an external phy, not a switch, deleted forced link speed
- fixed led color
Patch made for 3.14 kernel patches.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: also fix 3.14, refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41420
Spotted by several buildbots.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Patchwork: http://patchwork.openwrt.org/patch/5768/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41391
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
This enables the procd nand upgrade for ZyXEL NBG 6716. Also the ubi config
is cleaned up to match the wndr4300.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41346
- Support set VLAN ID of each vlan.
- Support untag feature.
- Replace register address with C MACRO.
- There are 8 ports for MT7530 actually.
Signed-off-by: Xiongfei Guo <xfguo@credosemi.com>
SVN-Revision: 41331
add missing kernelnames to Makefile because those files are needed in 'target/linux/mpc83xx/image/Makefile'. Without them a compilation for mpc83xx is not possible - the buildbot stops with the error "No such file or directory"
Signed-off-by: Claudio Thomas <ct@xmodus-systems.de>
SVN-Revision: 41330
We do not need global access to it, so move it from arch include to the
mtd subdir.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41321
Pass I/O memory regions (flash read and MMR) via platform device
resources array and use them inside spiflash driver.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41320
Moving the start of IO mem to 0x10000000 leads to allocation conflict
with SPI flash memory region, which starts at 0x08000000.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41319
We should not detect actual flash size during board initialization to
find board config at the end of the flash, just use large enough mapping
size (currently 128 mbit). If mapping size is larger than the actual
flash size, than flash will simply be mapped multiple times. This change
simplifies code by removing duplication and saves about 200 bytes of
uncompressed kernel :)
Tested with Ubnt LS2 board equipped with STM 25p32v6p NOR flash (32 mbit).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41317
Merge 3_10-updates.patch into the ar2313_ethernet.patch since it contains
only one ethernet driver fix.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41316
As far as I am aware, amongst the lantiq boards, jffs2_nand was
only used on the BTHOMEHUBV2B. Ubi-related modifications to the
device tree for that board mean that the resulting jffs2 images
no longer work, and are no longer required anyway. So I suggest
removing the related configuration, which this patch does.
If anyone else is using jffs2_nand on a lantiq target please speak
up!
Incidentally, for a jffs2 rootfs partition concatenated to the
kernel image to be recognised and mounted correctly on nand
this patch or something equivalent is required:
http://patchwork.openwrt.org/patch/5110/
It is marked as accepted in patchwork but doesn't seem to have
been committed. As far as I am concerned it too is deprecated.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41312
Setting this flag allows rootfs_data to expand on first boot
to fill remaining free space on nand.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41310
Use the CFE_EPTSEAL to tell them apart at runtime. Added for now only
for the 3.14 until properly tested.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41296
move both asus boards to asus.mk
rename HW5503G profile to HW550-3G to match name in image/Makefile
(fixes#16599)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41271
At the moment, an rootfs.ubi is copied over to bin/lantiq
but rootfs-overlay.ubi is not. This adds it.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41270
Revision r41256 introduced a typo (wandaboard => wandboard), but later
revisions expect to match on "wandboard"
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 41262
WAN and LAN are swapped the wrong way around. This patch fixes that by adding the 951Ui-2HnD to ar71xx.sh and the relevant entry in 02_network.
This patch also defines the ACT LED as the status LED in diag.sh.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41255
This patch adds factory image building for the DGN3500, all variants,
and fixes sysupgrade images to make them play nice with the sercomm
secondary boot loader.
The factory images can be used directly in the update dialog in the
interface of the stock firmware and via the special Sercomm bootmode
and a special windows flashing utility (allegedly present in the CD
that came with the device -- but it's also compatible with the NSLU2
Upgrade_207_XP utility.) The special bootmode can be activated by
turning the device on while holding the reset button pressed, then
releasing it when the power led starts blinking red and green. Please
notice that if using the 207 utility, it will always report that the
flashing failed even though it completed successfully. Just power
cycle the router manually after the utility reports the failure and
OpenWRT will boot. This same utility (despite reporting failure in
this case too) can revert a DGN3500 (any variant) to the appropriate
stock Netgear firmware.
This patch is a heavily modified version of a package I found on the
OpenWRT forum with a couple fixes and features added -- mainly the
generation of all the different image variants to support all known
models directly, atm known variants are AnnexA-WW, AnnexA-NA and
AnnexB-DE/GR.
I tested the patch successfully on my device.
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 41236
A modified version of 552-ubifs-respect-silent-mount-flag.patch has
been merged upstream. Replace the patch in OpenWrt with the version
which has been merged.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41218
Without this, the ports all end up on vlan 1. This enables a separate
WAN port that works.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41216
In a recent revision (r41177) John Crispin removed the profile for the
AsiaRF AWM002 eval board while adding another AsiaRF board. This
patch restores AWM002 and also corrects a misspelling and an
apparently errant reference to an Allnet ALL0239-3G device.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41215
This patches the BTHOMEHUB2B device tree to make use of the
new code for automatic detection of the ubi partition and the
rootfs type within it. Gets rid of the ugly alternative bootargs
lines.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41214
Similar to the rootfs hacks on NOR flash devices, this series
introduces support for auto-attaching (ubi device), auto-creating
(ubiblock device) and mounting the "rootfs" (ubifs or squashfs)
volume.
This is needed so OpenWrt can start without relying on the bootloader
to pass the ubi.mtd, ubi.block, rootfs and rootfstype parameters, but
instead auto-detect the root filesystem according to a simple convention.
OpenWrt-specific:
490-ubi-auto-attach-mtd-device-named-ubi-or-data-on-boot.patch
491-ubi-auto-create-ubiblock-device-for-rootfs.patch
492-try-auto-mounting-ubi0-rootfs-in-init-do_mounts.c.patch
493-ubi-set-ROOT_DEV-to-ubiblock-rootfs-if-unset.patch
sent upstream:
552-ubifs-respect-silent-mount-flag.patch
http://lists.infradead.org/pipermail/linux-mtd/2014-May/053893.html
v2: actually retry with MS_RDONLY when mounting read-only ubifs root
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41119
Use msleep(20) instead of msleep(10) to make code closer to reality
since msleep can sleep for up to 20ms even we request shorter delay.
All updated calls are located in PCI initialization routine which is
called only once upon device boot. So there should be no performance
issues caused by more longer delay.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41096
Use __func__ instead of gcc specific __FUNCTION__ as suggested by
checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41093
Move trailing statements to next line with indentation as suggested by
checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41092
Various indent fixes suggested by checkpatch: use tabs, use same level
of indentation for switch and case, correct indentation levels.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41090
Remove some unnecessary includes and use <linux/foo.h> instead of
<asm/foo.h> when it possible as suggested by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41089
Use more particular functions dev_<level> or pr_<level>(...) insead of
direct printk(...) call. Add KERN_LEVEL to calls what missed it.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41088
Fix braces location, remove unnecessary empty lines before or after code
block, remove useless braces. All cases are detected by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41087
Remove parentheses around return values since return is no a function,
as suggested by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41083
Fix comment issues detected by checkpatch. Convert C99 // comments to
ordinary /* ... */ comments. Correct block comments style or convert
them to single line comments.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41081
Change fooBar variables names to foo_bar as suggested by checkpatch,
write few tables names in lower case and correctly place __initdata
keyword.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41080
With this patch the mips74k subtarget will be compiled with optimized
compiler options to generated smaller and faster code. This currently
breaks broadcom-wl, because the binary blob is only compiled with
mipsr1 support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41050
This fixes some strange problems with tg3. I assume that the Ethernet
driver was not brought up if the switch was named switch0.
This was reported and tested by ernesto (Faulp3lz).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41042
All new devices (with MIPS 74K CPU) are based on BCMA SoC and have
Ethernet core supported by bgmac. Create a new subtarget to generate
optimized builds.
This is just a beginning, further tweaks (like kernel configuration)
are still possible. This decreases default root.squashfs by ~128 kB.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41025
This allows creating more subtargets and optimize builds per family.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41024
Remove old irq map patch and replace it with the propper upstream patches
allowing IMX6 PCIe devices behind PCIe switches to work properly.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 41004
ath5k fix in wifi and ethernet eeprom handling patch.
Without the line that adds the patch of_ath5k_eeprom_probe cause a
kernel panic, at least with the ARV4518PW.
Tested only in the modem-router mentioned above.
This patch is based in Bruno's hack present in patch #5454.
Signed off by: Bruno Rodríguez <bruno.rodriguez.1980@gmail.com>
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40999
The canutils package is in the packages repo and not part of trunk, so we
should not enable them by default.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40991
Add the following kernel modules by default (which are present on most Ventana
baseboards):
- kmod-leds-gpio (user leds)
- kmod-sound-core (required as a dependency of the other sound modules)
- kmod-pps-gpio (Pulse-Per-Second)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40990
The Gateworks Ventana board names have been adjusted per upstream patches
to include all IMX6 SoC variants.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40989
update the Ventana DTS files with upstream fixes:
- The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common and
not baseboard specific.
- removed obsolete crts
- fix include typo: The imx6q-gw51xx needs to include imx6qdl-gw51xx.dtsi
- fix gw52xx clock for sgtl5000 ananlog audio codec
- fix LVDS mapping for Ventana GW52xx/GW53xx/GW54xx
- add LVDS backlight for Ventana
- update model descriptions for all processor variants
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40988
update the Ventana DTS files with upstream fixes:
- The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common an
not baseboard specific.
- update model descriptions for all processor variants
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40987
It was augmented by CONFIG_USB_GADGET...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40986
