This patch configures the correct ath9k WLAN LED polarity for the TDW8970,
and for the TDW8980 as well.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47969
Still unused, but u-boot doesn't take care of the led, which results in a
permanent switched on 5GHz LED.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47915
This patch configures the correct ath9k WLAN LED polarity for the TDW8970.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47913
The TDW8970 has a AR9381, which is the bgn 3x3:3 variant of the AR938x family.
The TDW8980 has a AR9287, which is the bgn 2x2:2 variant of the AR928x family.
This means that the chip for both routers is 2.4 GHz only.
Anyway, the manufacturer didn't disable the 5 GHz band in the EEPROM partition
(at least on my TDW8970).
So this patch disables the 5 GHz band.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47912
Now that we have redistributable vdsl/adsl firmware blobs in /lib/firmware,
we can drop the dsl_fw partition and extend the firmware partition.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47783
This reverts commit 68c2e4789b4f071ee75d39248f4d08fe8283eb28.
commit r47159 was bad
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47207
The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz
wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47130
Since the AR9 USB is very similar to the VR9 USB it too can be used with
the upstream DWC2 driver.
Here are the DTS definitions which make it compatible with the DWC2
driver.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46914
Newer DSL driver versions depend on the address information.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46221
In r44391 the kernel partion size was increased to allow larger kernels,
but the rootfs partition offset was missed. Fix this by setting the
rootfs offset to the expected value.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45868
Here the device tree entry for ifxhcd is listed as compatible with one
supported in dwc2 (after patching the dwc driver appropriately).
A second entry is added to support the second core of the hcd. This
entry is listed to be compatible with only dwc2. Done this way there
should be backwards support for both hcd drivers (ltq-hcd and dwc2)
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44676
This patch builds on the previous three to streamline support for the
Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44032
The bb-rc3 image for the BTHOMEHUBV2B is too big for its
mtd partition. This patch corrects the partition sizes in
the device tree. This patch should really go in before
bb-final, otherwise the BTHOMEHUBV2B images won't be useable.
I do apologise for not spotting this straight away.
Many thanks,
Ben
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 42316
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
This patches the BTHOMEHUB2B device tree to make use of the
new code for automatic detection of the ubi partition and the
rootfs type within it. Gets rid of the ugly alternative bootargs
lines.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41214
this should really be auto detected by the kernel, lets used this workaround until the real
solution is ready
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40418
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40329
This patch adds almost full support for this board.
- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40319
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40317
Some ARV4510PW units seem to have unstable PCI due to missing pull-up
resistors. This patch makes sure that the GPIO lines are driven properly.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39587
Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is
severely lacking. This patch brings it up-to-date.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39230
*) can not connect to switch chip
*) only one usb port is working
*) wifi is not working
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37712
This patch enables retrieving the wifi calibration data from an MTD partition.
Try to copy mac address from ethernet before generating a random one.
This fixes DGN3500 ath9k support.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 37087
Fix EBU leds by removing req2 and gnt2 from pinmux.
Fix rfkill button gpio.
Enable reset button.
Fix power led activation status.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 37004
Use platform data array for storing ath5k EEPROM instead of creating another one.
EEPROM size is 2048 words (2 bytes), so we must read 4096 bytes from flash.
No need to keep the checksum fix now that the EEPROM is loaded completely.
Add a manual eeprom swap for ath9k and keep the endian way.
Use mac-offset property retrieved from the DTS.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 36901
The GPIO buttons of ARV752DPW are active low.
Treating them as active high caused a reboot loop as a reset-button
press is detected by gpio-button-hotplug/gpio-keys-polled on startup.
This fixes: https://dev.openwrt.org/ticket/12642
Signed-off-by: Rafael Gieschke <rafael@gieschke.de>
SVN-Revision: 36783
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36781
