Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
The more straight forward approach for generating the pure and unpadded
kernel file which then can be used for initramfs straight.
Build options for factory.img and sysupgrade.tar are handeled
seperately.
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.
Fixes: FS#542
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO
For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f
For debugging serial console is easily visible on board, no soldering needed.
Signed-off-by: André Valentin <avalentin@marcant.net>
The R7800 is an IPQ8065, so rename its dts file to reflect that fact.
Also fold the R7500v2 dts addition into the existing 800-devicetree.patch.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1)Changes
- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime
2)Testing
Tested on IPQ AP148 Board:
a. NOR boot and NAND boot
b. ethernet network and ath10k wifi
c. ubi sysupgrade
UnTested
dwc3 usb has not been validated on IPQ board(AP148)
3)Known Issues:
Once we flash ubi image on AP148, and if we reset the board, uboot on
first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
and not what linux expects which causes errors when trying to mount rootfs.
In order to test this, we can use the below steps:
a. Flash the ubi image on board and don't reset the board
b. load the kernel fit image in RAM and boot from there.
Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
the board names used by the upgrade check differ from the device names
in case, so always set them. We can't rely on tolower or similar since
different locales might have different rules for lower case letters, so
set them explicitily.
Fixes sysupgrade rejecting *-sysupgrade.tar because of the difference.
Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47381
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.
Known issues:
* 5 GHz wifi not working - there is no quantenna driver
* One of the USB ports is not working
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46796
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46789
Switch ipq806x to the new image build system. Image files might change
slightly their names, but the generated files should not change.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46602
Certain AP148 platforms (and derivative) use bootloaders which did not
have DT enabled.
In order to support these old platforms, we'll now make the following
modifications:
*explicitely add the memory node in the AP148 DT: this used to be added
by new u-boot through a run-time patch mechanism. We'll now add it
explicitely so it works on boots which don't support that feature. New
boots will have the node twice, the second one will be ignored.
*add the zImage generation next to the FIT image for AP148.
Other platforms using non-DT enabled bootloaders may want to leverage
this zImage code to generate their own firmare as well.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46555
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46361
DB149 is a IPQ8064 based platform. This patch adds the init scripts to
detect it, configure the network accordingly, and generate a flashable
image for it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45537
Patches in the ipq806x/patches folder were out of tree in v3.14. The
newest patch at the time was from June, so we can safely assume that
either the patches have been merged, or they have been rejected for
a good reason. If patches are seen missing, we'll cherry-pick them
on a per-needed basis.
This new kernel have been tested on AP148, which seems to works fine.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44386
Patches are generated using the "format-patch" command from the
following location:
*https://www.codeaurora.org/cgit/quic/kernel/galak-msm/log/?h=apq_ipq_base
*rev=0771849495b4128cac2faf7d49c85c729fc48b20
Patches numbered 76/77/102/103 have already been integrated in 3.14.12,
so they're not in this list.
All these patches are either integrated are pending integration into
kernel.org, therefore these patches should go away once the kernel
gets upgraded to 3.16.
Support is currently limited to AP148 board but can be extended to other
platforms in the future.
These changes do not cover ethernet connectivity.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 42334
