Only netboot tested, so no images or now.
GbE ports are only working in FE mode, and leds do not work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39679
Completely untested except for booting from network; wan port
only works in 10/HD, lan1 only in 100/FD.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39678
BCM63168 has 6 ports (3 FE PHY, 1 GE PHY, two RGMII) and BCM63268
has two additional RGMII ports, making it 8.
Fix this by checking the chip variant and applying an appropriate
limit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39677
Support for Asmax AR 1004g router
Signed-off-by: Adrian Feliks <mexit@o2.pl>
Patchwork: http://patchwork.openwrt.org/patch/4464/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39674
This adds kernel support support for Sagemcom F@st 2704 wireless ADSL
router.
It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+
modem equipped with 64 MiB RAM and 8 MiB flash.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4266/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39671
Add kernel support for the BCM963269BHR board, USB and Ethernet switch,
LEDs and buttons are working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39363
Allow using the HSSPI controller since it works just fine, as well as
the integrated switch core, since that one works too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39362
Update a few devices with their actual port numbers, especially those
with two ports.
Should allow properly using the second port on the Neufboxen and HW553
and HW556.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39325
Allow setting the number of available usb host ports for boards with
additional sanity checks to allow using the second port on devices
where it is available.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39324
USB will fail to work if compiling with BCM6318 only if BCM63XX_HAS_EHCI
and BCM63XX_HAS_OHCI are not selected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39322
Return the same clock for usbh and usbd on BCM6318 to prevent the clock
getting disabled despite being supposed to be enabled, e.g. by the
following sequence:
clk_enable(usbh); <- usbh->usage = 1, enabled
clk_enable(usbd); <- usbd->usage = 1, enabled (no effect)
clk_disable(usbd); <- usbd->usage = 0, -> disabled!
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39321
Changeset r39302 updated a board section and added twice .has_ehci0,
this is not necessary, so fix it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39304
BCM6318 has a special initialization sequence which involves touching
PLL control registers in the USBH_PRIV register space, as well as
toggling a bit the Simulation control register.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39302
Enable the use of the USB gadget device at the board level so we can use
bcm63xx_udc on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39292
Also fixing a build warning due to a misplaced parenthesis in the
previous submission.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39291
Very similar to the BCM96318REF board except for the name and the
SDRAM/DDR configuration which is totally transparent for us.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39286
Add basic support for the BCM96318REF board which is comprised of:
- HS-SPI flash support
- Ethernet switch support
- USB slave device support
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39283
Provide clock toggling for the USB host and slave controller as well as
for the Ethernet Switch. The bcm63xx_enetsw driver is changed not to use
request_mem_region() as the Roboswitch register overlaps with the
Roboswitch IUDMA channels, hence making the driver return -EBUSY. A
future fix might be to use variable size RSET_ENETSW sizes depending on
the chip we are targetting.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39282
While adding support for BCM6345 Ethernet, some changes in the macros
ENETDMA{C,S} where introduced which now make the bcm63xx USB gadget
driver fail to build. Fix this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39279
A missing condition check in dev-hsspi.c prevented the controller from
being registered on 6318 where it is fully functional.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39278
varid might both unused and unitialized when building for e.g: bcm6318,
fix these two warnings turned into errors.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39277
BCM63XX's ohci controller does not need the frame number shift, but that
was guarded with a PPC symbol. Fix this by making the no-fix generally
available.
This is a regression from the previous conversion to ohci platform driver.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39274
CFE seems to leave the SPI flash mapping in an invalid state after
loading the kernel on some reference boards, so fix it up on boot.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39273
Add inital support for BCM6318, but keep it disabled for now until
most things are supported.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39272
Add initial support for the BCM63268 family of SoCs, but keep it
disabled for now as most things don't work yet.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39271
Some SoCs have variants which are mostly the same, but use a different
chip id (or not). Add code for detecting them and handling them as
their standard counterparts.
This adds support for e.g. BCM6369.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39269
Remove the non runtime detect code since its effectiveness is dubious
and almost never used.
Also update affinity patches to work on top of it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39268
Update bmips cleanup patches with upstream submission and backport a few
bmips fixes.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39267
Fixes generic SPI flash accesses on BCM6358/BCM6368. BCM6338 still needs
additional fixes for M25P80, so it remains broken for now.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39266
Fixes e.g. SPI flash access on BCM6358/BCM6368. Transfers < 256 bytes
are not affected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39265
Update the HSSPI driver with the upstream submitted one that has a
workaround for the auto cs down issue.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39264
