* fix up the order of respawn parameters for ubus
* add a event broadcast function
* add debug level handover between preinit and main process
* make the service running trigger be queued directly after the service was startetd
* Allow process respawning forever
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38868
- instead of writing one (or more) ACCEPT rules in the filter table
for each redirect install a global ctstate DNAT accept rule per zone
- discard rules and redirects which have invalid options set instead
of silently skipping the invalid values
SVN-Revision: 38849
move xfsprogs to the right submenu
e2fsprogs, btrfs-progs and other stuff is there already
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 38838
Current version of ath10k in the recently updated wireless-testing
package requires a new firmware. This patch fixes the issue.
v2:
* fix (hopefully) the mangled whitespaces
* actually install the new firmware instead of the old
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 38835
This patch was copied from a more recent backports versions. This fixes
a build problem with kernel < 3.6.
This closes#14475
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38833
move log service from procd to ubox
some debloating on procd
the preinit part of procd is now also a seperate binary
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38822
The correct bits are now cleared in the IPv6 address as the shift
value to the correct byte in the IPv6 address was wrong. Depending
on the stack values this could result in a hanging 6rdcalc program
due to an endless loop.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 38818
RIPEMD is needed to update erlang and i'd like to enable RIPEMD160 support in openssh.
Size compared:
openssl without RIPEMD/160 support:
647K 29. Okt 20:00 bin/ar71xx/packages/libopenssl_1.0.1e-2_ar71xx.ipk
openssl with RIPEMD/160 support:
652K 8. Nov 15:11 bin/ar71xx/packages/libopenssl_1.0.1e-2_ar71xx.ipk
So the file size just grows ~5kb, which shouldn't be a problem.
Signed-off-by: Peter Wagner <tripolar@gmx.at>
SVN-Revision: 38809
The current implementation of mtd will not append the backup
file created by sysupgrade to the correct partition, as mtd will append
the data to first jffs2 partition it finds. As the kernel is also
stored on a jffs2 partition (which resides before the overlay
partition), the data will be appended to this partition.
To fix this problem, a new option
-s <number> skip the first n bytes when appending data to the jffs2 partiton, defaults to "0"
is added to mtd.
Signed-off-by: Peter Wagner <tripolar@gmx.at>
SVN-Revision: 38807
In commit r38690, the MAC address canonicalization
has been converted to use 'tr' instead of 'printf'.
This only works if with MAC addresses which uses
the 'xx:xx:xx:xx:xx:xx' format.
However on some boards, the MAC addresses are stored
in different format in the mtd partition. Some vendors
are using hyphens or dots as separators instead of
colons. Also the leading zeroes may be missing from the
individual octets or those are replaced with spaces.
Add a new function which can be used to convert these
into the 'xx:xx:xx:xx:xx:xx' format. Also update the
'mtd_get_mac_ascii' function to use the new helper.
The helper function is based on this code:
http://isquared.nl/blog/2010/08/11/Bash-function-to-canonicalize-MAC-addresses/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38803
This was copied from wireless-regdb.git commit a14052b85e5d70e37a31962a9c56c0cdbb9acafc
The passive-scan/no-ibss flag of channels 36-48 in the world regd were
removed like it was done in r32126.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38797
swapon/swapoff are no longer provided by swap-utils; they are provided
by block-mount instead.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38795
When enabling multiple VIFS, the driver sometimes crashes. The frequency
of the crash increases as more VIFS are enabled.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38762
Read the number of virtual interfaces to support from the device
capabilities; as some newer devices can support up to 16.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38759
Some devices initialize with a default address (common to all H/W).
The address needs to be changeable so that a unique address can be
assigned to each AP.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38757
Default gmode to "GOnly" unless explicitly overwridden. This corrects
processing for 11ng to specify "GOnly" for gmode instead of "Auto"
(which translated to "bg").
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38754
'nas' must be shutdown independently for each 'wl' device to properly
support devices with multiple radios. Do the shutdown when the device
is disabled instead of when it is brought up.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38753
A single instance of 'nas' can support multiple interfaces; there's
no need to run multiple instances.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38752
Modify the band reporting for broadcom devices to correctly report
HW capability. Currently, 802.11na devices report "bgn"; but should be
reporting "an".
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38749
'netifd' treats all devices with a "." in their name as vlan devices.
Modify the name of virtual/WDS interfaces created by broadcom-wl to use
a "-" instead of a ".", so they will be treated as simple devices
by 'netifd'.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38748
The associations list for Broadcom WDS interfaces are duplicate to those
reported by the corresponding AP interface; so there is no need to report
them again.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38746
Modify the hwmodelist reporting for broadcom devices to include
proper reporting of 802.11n support.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38745
The mtd_get_mac_ascii utility function was broken. This fixes it.
- Remove the superfluous include of /lib/functions.sh. The
function is already in that file so it is pointless,
- only use a variable if the whole key word matches,
- don't try to process the MAC address if it is empty,
- use 'tr' to canonicalize the MAC address,
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[juhosg: add more fixes, update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38690
swapon/swapoff are no longer provided by swap-utils, so remove them from
the description as well.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38672
'swapon/swapoff' are now provided by 'block-mount'; enabling them by default in busybox is no longer required and adds unnecessary bloat.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38671
Only reload hostname and timezone config on /etc/init.d/boot restart.
Module loading and basic boot setup is only done during boot.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 38670
The jffs2_ready() function in mount_root.c checks
the presence of various JFFS2 markers at the start
of a given MTD device. The function works on NOR
flashes because JFFS2 puts 'cleanmarker' nodes at
the start of freshly erased blocks.
However if jffs2 is used on a MTD device emulated
by the gluebi layer, the 'cleanmarker' nodes are
not present and the jffs2_ready() function fails.
Update the code to handle jffs2 correctly even on
MTD devices emulated by the gluebi layer.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38654
Changeset r36943 ("dnsmasq: use host-record instead of address") removed
the automatic domain expansion for config domain sections, this breaks
existing setups and alters the old behaviour in unexpected ways, therfore
restore behaviour of the current stable release.
Additionally handle fully qualified hostnames properly when setting up the
own hostrecord by stripping the local domain part form the given name
instead of unconditionally appending it, so that "example.lan" results
in "example example.lan" and not "example.lan example.lan.lan".
SVN-Revision: 38648
- clean up duplication of procd instance handling code
- using --cd *after* --config is rather pointless
- to be able to log errors properly, --syslog needs to be passed before --config
- tell procd about the generated or referenced config file instead of
the uci file. this avoids having to restart all instances if only one
of them changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38632
Un-reverts the previous update commit and forward-ports the patch
to improve legacy SSLv2 handshake handling.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 38609
* Various RFC compliance fixes (thanks to Hans Dedecker)
* Fix RA spam filter logic causing ipv6 connection issues
* Fix parameters -F and -P being order dependent
SVN-Revision: 38577
Reverts the CyaSSL version bump for now since the update completely broke
trunk building due to incompatible changes in the IO callback API which in
turn breaks the core ustream-ssl package.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 38576
* Use network.interface dump call instead of individual status calls
to reduce overall netifd lookups and invokes to 1 per fw3 process.
* Allow protocol handlers to assign a firewall zone for an interface
in the data section to allow for dynamic firewall zone assignment.
SVN-Revision: 38504
* Add ubus methods for global interface status
* Add ubus function to create nested interfaces
* Add protocol update notifications and hotplug legacy calls
* Fix: key to data elements point at wrong memory area
* Add support for source-restricted routes
* Add option "delegate" to toggle prefix delegation
* Reevaluate target routes also on interface update
SVN-Revision: 38453
A similar change was recently merged in iw commit
58b46da26ab9b5ff31c7033e175351eb1301d9af
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 38449
There are several cases within 'luci' that attempt to access the interface
'type' from within the 'type' specific meta tables; however, 'type' is not
currently available there. Replicate the common metadata in the 'type'
specific meta tables.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38448
Possible parameters are yes, no and adaptive. See manpage for more information.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
SVN-Revision: 38412
Fixes issues with UBIFS file system when due to unclean shutdown files would
end up with size 0. Furthermore, few style fixes are included too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38410
* Make SOL_MAX_RT configurable and default back to 120s
* Prefer servers with bigger prefixes (allows to use Comcast /60)
* Don't hang indefinitely if DHCPv6 REQUEST is not answered
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 38393
The kmodloader executable disregarded the global directory prefix in
scan_module_folder() leading to a broken extroot for non-builtin modules.
Update to current git head to fix the prefix handling again.
SVN-Revision: 38392
This is to work around issues with package list generators creating
empty fields in some environments.
Based on a patch by Paul Selkrik <pselkrik@isc.org>
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 38390
The switch driver is not used by brcm47xx any more and can be removed,
instead of this switch driver b53 is used now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38387
Config options in backports are starting with CPTCFG and not with CONFIG_.
CONFIG_B43_BCMA was never true.
This closes#13883.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38385
There are certain consumer devices which are outliers in protocol conformance.
An example is Samsung bluray players, which require broadcast DHCP responses
(on Ethernet only, strangely not on Wifi).
By specifying:
config host
...
option broadcast 1
this will enable the response to be sent as an Ethernet broadcast and not as
a unicast.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 38365
- do not insert duplicate rules when setting up reflection to a zone containing multiple interfaces
- set up reflection for any protocol, not just TCP and UDP
SVN-Revision: 38361
proto_pptp_setup is responsible for loading the required modules to establish
a pptp connection to a foreign peer. The function checks whether all required
modules are already loaded, before actually loading them.
It seems that the filter being used to accomplish this, is not restrictive
enough in some cases. For instance when pptp nat helper modules are present on
a system, and already loaded before a pptp connection is enabled. Then the
search filter (possibly) returns the following for module=pptp, where actually
no matches are expected, resulting in the pptp.ko module not being loaded,
thereby failing to establish the pptp connection.
# module="pptp" ; grep "$module" /proc/modules
nf_nat_pptp 1312 0 - Live 0x86ce7000
nf_conntrack_pptp 3072 1 nf_nat_pptp, Live 0x86cb9000
nf_nat_proto_gre 784 1 nf_nat_pptp, Live 0x86cba000
nf_conntrack_proto_gre 2368 1 nf_conntrack_pptp, Live 0x86cbf000
nf_nat 9792 13 nf_nat_rtsp,nf_nat_tftp,nf_nat_sip,nf_nat_pptp,nf_nat_h323,nf_nat_proto_gre,nf_nat_amanda,nf_nat_irc,nf_nat_ftp,ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,iptable_nat, Live 0x86ca8000
nf_conntrack 37264 31 nf_nat_rtsp,nf_conntrack_rtsp,nf_nat_tftp,nf_conntrack_tftp,nf_nat_snmp_basic,nf_conntrack_snmp,nf_nat_sip,nf_conntrack_sip,nf_nat_pptp,nf_conntrack_pptp,nf_nat_h323,nf_conntrack_h323,nf_conntrack_proto_gre,nf_nat_amanda,nf_conntrack_amanda,nf_conntrack_broadcast,nf_nat_irc,nf_conntrack_irc,nf_nat_ftp,nf_conntrack_ftp,ipt_MASQUERADE,iptable_nat,nf_nat,xt_helper,xt_connmark,xt_connbytes,xt_conntrack,xt_CT,xt_NOTRACK,xt_state,nf_conntrack_ipv4, Live 0x86c90000
The search filter can be made more accurate/restrictive, by requiring the
occurance of the exact name of the module at the beginning of a line in
/proc/modules.
# module="pptp" ; grep "^$module " /proc/modules
pptp 13296 2 - Live 0x86e80000
Signed-off-by: Tijs Van Buggenhout <tvb@able.be>
SVN-Revision: 38358
Currently, in order to configure the authentication daemon in
8021x mode, we need to set wireless.@wifi-iface[0].encryption="wpa"
Though it works it confuses folks as 8021x is using WEP
encryption and not WPA. Therefore the terminology itself is
confusing. This change adds 8021x as a recognized string for 8021x
authentication.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38339
Setting wireless.@wifi-iface[N].ext_registrar=1 will enable UPNP
advertising and add an external registrar to the interface this vif
belongs to (br-lan if the vif is included in the LAN bridge). By
enabling this we append upnp_iface=xxx to the hostapd config file.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38338
Enable CONFIG_WPS2 for hostapd. This is required to support
options like Virtual Push Button in WPS.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38337
In 2009 OpenWrt's hostapd config added an "auth_cache" boolean
to be used to address a reported issue #12129 [0] on a forum [1].
The reported issue on the ticket is different that the one
described on the forum. The commit was r33359. This change broke
proper RSN preauthentication [2] [3] [4] expectations on hostapd's
configuration for WPA2 and this in turn disabled PMKSA caching and
Opportunistic Key Caching. This change:
* Leaves the "auth_cache" to be used only for WPA networks for those
looking to use this as a workaround to a reported issue but annotates
a warning over its usage.
* Separate "auth_cache" from WPA2 RSN preauthentication, leaving
WPA2 RSN preauthentication to enabled only with "rsn_preauth" with
the expected and recommended settings.
* Adds a new WPA2 RSN preauthentication "rsn_preauth_testing" to
be used when evaluating funcionality for WPA2 RSN preauthentication
with the expected and recommended settings with the only difference
so far with what should be enabled by default to disable Opportunistic
Key Caching.
Disabling the PMKSA cache should mean the STA could not roam off and back
onto the AP that had PMKSA caching disabled and would require a full
authentication cycle. This fixes this for WPA2 networks with
RSN preauthentication enabled.
This change should be applied to AA as well as trunk.
TL DR;
The issue described on the forum has to do with failure of a STA
being able to try to authenticate again with the AP if it failed
its first try. This may have been an issue with hostapd in 2009
but as per some tests I cannot reproduce this today on a WPA2
network.
The issue described on the ticket alludes to a security issue with the
design of using a Radius server to authenticate to an AP. The issue
vaguely alludes to the circumstances of zapping a user, deleting their
authentication credentials to log in to the network, and that if
RSN preauthentication is enabled with PMKSA caching that the user
that was zapped would still be able to authenticate.
Lets treat these as separate issues.
I cannot reproduce the first issue reported on the forums of not
being able to authenticate anymore on a WPA2 network.
The issue reported on the ticket modified WPA2 RSN preauthentication
by adding two fields to the hostapd configuration if auth_cache
was enabled:
* disable_pmksa_caching=1
* okc=0
The first one disables PMKSA authentication cache.
The second one disables Opportunistic Key Caching.
The issue reported on the ticket was fixed by implementing a workaround
in hostapd's configuration. Disabling PMKSA caching breaks proper use
of WPA2 RSN pre authentication. The usage of disable_pmksa_caching=1
prevents hostapd from adding PMKSA entries into its cache when a successful
802.1x authentication occurs. In practice RSN preauthentication would
trigger a STA to perform authentication with other APs on the same SSID,
it would then have its own supplicant PMKSA cache held. If a STA roams
between one AP to another no new authenitcation would need to be performed
as the new AP would already have authenticated the STA. The purpose of the
PMKSA cache on the AP side would be for the AP to use the same PMKID for
a STA when the STA roams off onto another BSSID and later comes back to it.
Disabling Opportunistic Key Caching could help the reported issue
as well but its not the correct place to address this. Opportunistic
Key Caching enables an AP with different interfaces to share the
PMKSA cache. Its a technical enhancement and disabling it would
be useful to let a testing suite properly test for RSN preauthentication
given that otherwise Opportunistic Key Caching would enable an
interface being tested to derive its own derive the PMKSA entry.
In production though okc=1 should be enabled to help with RSN
preauthentication.
The real fix for this particular issue outside of the scope of hostapd's
configuration and it should not be dealt with as a workaround to
its configuration and breaking expected RSN preauthentication and
technical optimizations. Revert this change and enable users to pick
and choose to enable or disable disable_pmksa_caching and okc expecting them
to instead have read clearly more what these do.
As for the core issure ported, the correct place to fix this is to
enable a sort of messaging between the RADIUS server and its peers
so that if caching for authentication is enabled that cache can be
cleared upon user credential updates. Updating a user password
(not just zapping a user) is another possible issue that would need
to be resolved here. Another part of the solution might be to reduce
the cache timing to account for any systematic limitations (RADIUS
server not able to ask peers to clear cache might be
one).
[0] https://dev.openwrt.org/changeset/33359
[1] https://forum.openwrt.org/viewtopic.php?id=19596
[2] http://wireless.kernel.org/en/users/Documentation/hostapd#IEEE_802.11i.2FRSN.2FWPA2_pre-authentication
[3] http://wireless.kernel.org/en/users/Documentation/wpa_supplicant#RSN_preauthentication
[4] http://wiki.openwrt.org/doc/recipes/rsn_preauthentication
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
SVN-Revision: 38336
This adds the eap_reauth_period to be used for modifying
the RADIUS server reauthentication authentication period,
a parameter that gets passed directly to the hostapd
configuration file.
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
SVN-Revision: 38334
WL_TI is bool but was set to =m, which deactivated it. Now it is set to
=y and should be activated in the config so the wl12xx driver gets
build.
This closes#14212.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38333
Somehow BRCMFMAC_USB was not set in the build and brcmfmac.ko did not had usb support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38332
Change the autoload number from '5' to '05' so the module loads earlier (as intended).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38293
Add package signing key and certificate configuration options to the
"Image configuration" submenu. If enabled, the Packages.gz list will
be signed as file Packages.sig. The passphrase for the signing key can
be sourced from a file or entered by the user. The signing certificate
is automatically added to the firmware image if opkg-smime is selected.
Signed-off-by: Evan Hunt <each@isc.org>
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 38284
After this change, "rmmod" and "modinfo" works even if the user gives
the file name spelling instead of the kernel internal one, so that e.g.
"rmmod nls_iso8859-1.ko" and "rmmod nls_iso8859_1" will both succeed.
SVN-Revision: 38252
Instead of canonicalizing module names in the internal avl tree simpyl use a
custom strcmp() variant for the avl tree key comparisation. The custom comperator
simply treats dashes and underscores the same, so "nls_iso8859-15" is equal to
"nls-iso8859-15".
This allows us to simplify the code considerably and makes manual "modprobe"
invocations more forgiving when looking up the given module name.
SVN-Revision: 38248
Should fix build errors with Linux 3.3/3.6 targets, which use different
kconfig symbols
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38238
Add support for the ADT7410 hwmon driver, a high precision
I2C temperature sensor.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[juhosg: update subject, reformat commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38186
Move pca953x support from i2c.mk to other.mk, where other
GPIO drivers are located. Remove duplicate pcf857x support
from i2c.mk.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[juhosg: update subject, and reformat commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38185
Changes include:
* removing unused variables
* replacing spaces with tabs where appropriate
* more consistency with variable declarations
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38142
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38036
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38001
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37977
Most of the Linksys devices without an own GPIO configuration where
detected as WRT54G. On one board this made OpenWrt to boot into
failsafe every time, because one GPIO configurated as button was not a
button.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37970
- fixes buffer corruption with JSON-RPC list calls
- change JSON-RPC protocol to include the session ID into the call
attributes instead of passing it via the URL
- forcibly pass effective session ID as "ubus_rpc_session" attribute
to called procedures
- change ubus acl checking to conform with new ubus session namespace
SVN-Revision: 37962
- recalculate session ACLs on reload
- support negative access group expressions in /etc/config/rpcd
- prevent destryoing the default session
- use "ubus_rpc_session" attribute as session identifier to enforce JSON-RPC proxy security
SVN-Revision: 37961
The imx sata module has only been backported to imx6 target. This change will
fix buildbot errors due to missing patches in other targets. Keep this until
all targets use kernel version with imx sata support in them.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37950
- introduces persistent null session to allow access to procedures without login
- implements session.login procedure to support user logins via json-rpc
SVN-Revision: 37941
- adds support for service triggering on config commit
- adds uci transaction support
- adds daemon reload support without loosing session data
- exports headers for use by external plugins
- drops LuCI2 in favor to an out of tree plugin
SVN-Revision: 37921
This fixes the following error:
keyspan: Unknown symbol ezusb_fx1_ihex_firmware_download (err 0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37899
This enables usage of the ath10k driver on OpenWrt. Only 2.0 PCI hardware
is supported. The ath10k firmware is currently only available
through github so use that as its source for now.
This goes build tested, not run time tested.
[Hauke: I did some minor changes]
Cc: ath10k@lists.infradead.org
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Mathieu Olivari <mathieu@qca.qualcomm.com>
Cc: Jerome Proffit <jproffit@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Matthew McClintock <mmcclint@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37898
The package makes it possible to create custom SPI
buses via GPIO lines.
This module is based on i2c-gpio-custom and allows to
configure an SPI bus via GPIO lines and expose it to
userspace without rebuilding the kernel. This is maily
intended to connect microcontrollers and other simple
SPI devices without making an ad-hoc kernel driver.
Signed-off-by: Marco Burato <zmaster.adsl@gmail.com>
[juhosg:
- change subject,
- extend and reformat commit message,
- cleanup checkpatch errors/warnings in module source]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37872
Backport some rt2x00 specific changes from
wireless-testing/master-2013-08-26 to add
support for RT3573 based devices.
Also refresh the rt2x00 specific patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37843
Currently package/Makefile only passes /lib /usr/lib and /usr/lib/ebtables
to mklibs. However, other libs can also reside in different subdirectories
(in my case /usr/lib/ipsec). Hence, create the list of library directories
dynamically.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 37841
hostapd supports "Dynamic Authorization Extensions", making it possible
to forcibly disconnect a user by sending it a RADIUS "Disconnect-Request"
packet.
I've added three new variables to enable setting of the
"radius_das_client" and "radius_das_port" variables in the hostapd
configuration, which enable these extensions.
* dae_client - IP of the client that can send disconnect requests
* dae_secret - shared secret for DAE packets
These are combined into the "radius_das_client" option in hostapd.conf
To enable the server, both dae_client and dae_secret must be set.
* dae_port - optional, default value is 3799 as specified in RFC 5176
Signed-off-by: Martijn van de Streek <martijn@vandestreek.net>
SVN-Revision: 37734
WEP in WDS is currently broken in hostapd. Add a patch
to fix the issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
SVN-Revision: 37733
Use the "start_disabled" option in hostapd that was added
in the earlier patch.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
SVN-Revision: 37732
Add a patch for hostapd that introduces a config option
"start_disabled" which can be used to bring up an AP
interface with beaconing disabled. This is useful in
a Repeater-AP setup where the Repeater AP has to start
beaconing only after the WDS link has been established.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
SVN-Revision: 37730
The BCM4331 supports a PCIe max request size of 512 bytes and uses
that, but the PCIe controller in the BCM4706 just supports 128 Bytes
and that causes a DMA error for packages bigger than 126 bytes. This
fixes the problem by setting the BCM4331 also to 128 Bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37709
The current dependency prevents building of the
rt2800{pci,usb} drivers for RT3883. Change the
dependency to fix this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37699
When CONFIG_LLC gets build as a module, also p8022.ko and psnap.ko are
getting build as a module. kmod-appletalk depends on llc.ko and
psnap.ko, but at least psnap.ko,was not packed. On most systems
CONFIG_LLC will be build into the kernel so this problem does not show
up.
This fixes the missing dependency of kmod-appletalk on psnap.ko
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37673
This adds button and led info, which I determined
by manually poking the gpio values.
Signed-off-by: Josh Stone <cuviper@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37655
TL-WR720N-v3 has a slider switch composed of 2 GPIO buttons which can be
used to swtich between 3 positions. At leat 1 button is in pressed state
in any of those positions. Initialize 'last_state' as 0 (released) will
cause the device to automatically enter failsafe mode on every bootup.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 37643
Comparing the RTSDK driver and mac80211 revealed, that this register needs
to have a special setup on rt5350.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37608
This patch enables setting the wifi led polarity from OF.
It can be used in a DTS' wmac section like this:
ralink,led-polarity = <1>;
Valid values are 0 or 1.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37607
this patches updates openvpn to v2.3.2
and adds a PKG_MD5SUM to the Makefile
This release fixes a memory access violation when cipher none is used
on ar71xx - at least with my config
Signed-off-by: Peter Wagner <tripolar@gmx.at>
SVN-Revision: 37560
This patch modifies the uci scripts to be able to
start meshd-nl80211 for encrypted mesh networks,
therefor a new script (authsae.sh) is inserted.
Signed-off-by: Emanuel Taube <emanuel.taube@gmail.com>
[etienne.champetier@free.fr: just update mac80211.sh path]
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
SVN-Revision: 37554
This patch adds authsae open80211s authentication daemon (http://open80211s.org)
It's a rework of Peter Naulls patch (http://patchwork.openwrt.org/patch/1350/)
I've excluded the sample conf file as it's useless when used with mac80211.sh (Emanuel Taube patch)
It now link against libnl-tiny instead of libnl (patch merged in authsae git)
Authsae is 58 Ko (OPENSSL_WITH_EC option adds 35Ko to libopenssl)
Signed-off-by: Peter Naulls <peter@chocky.org>
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
SVN-Revision: 37553
- discard vfat labels with only spaces
- support using swap files
- support extroot when required kmods and block-mount are installed on jffs2
SVN-Revision: 37551
This patch adds EC compilation options to openssl
OPENSSL_WITH_EC is needed for authsae (OPENSSL_WITH_EC2M isn't)
Activating ec (but not ec2m) in openssl take 35Ko more on ar71xx (ipk size)
Activating both take 52Ko.
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
SVN-Revision: 37523
Properly define the config symbol to n so it doesn't break build for
targets which do have it available (e.g. mostly everything except arm).
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37489
This forces all packets (even for un-aggregated traffic) through
software queues to improve fairness and stability
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37483
The malta target is broken since procd is used
as init. The initramfs image boots fine, however
the console is not working.
Improve the early console handling to fix the
problem.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37451
It hasn't been buildable for a long time, and there are no users of it
anymore left as all of them have been switched to the upstream accepted
version.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37436
xor.ko is needed by btrfs in 3.10+, so split it out into its own
package. Make it hidden as it does not provide any functionality on its
own.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37395
raid_pq.ko is needed by btrfs in 3.10+, so split it out into its own
package. Make it hidden as it does not provide any functionality on its
own.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37394
The reap functionality appears to have been accidentally disabled by
commit 74ded7257e5da5e309844d386290f24ae91950a6 to iptables.git, see:
git://git.netfilter.org/iptables.git
and subsequently in iptables 1.4.15 and later. This adds a patch to
restore reap functionality for recent_opts_v1.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 37328
This is now controlled by a module parameter and the default
configuration depends on brcmsmac being installed.
This patch causes b43 to take core rev 17 and 18 always by default.
SVN-Revision: 37307
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
SVN-Revision: 37304
Apparently there are some broken devices out there that have the local
bit already set in the factory MAC address. Move the | 0x2 over to the
other side of the xor operation to fix this without affecting devices
with proper addresses.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37269
It is only used by one driver that already depends on x86. Disabling it
prevents a few kilobytes of bloat from leaking into all targets via
CONFIG_BLK_DEV_BSG
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37254
lldpd 0.7.1 has several alignment issues that trip a system configured
to fault on misaligned accesses. Version 0.7.5 fixes that along with a
few other minor issues.
Signed-off-by: John Szakmeister <john@szakmeister.net>
SVN-Revision: 37168
the attached patch fixes a bug of px5g when instructed to build
certificates that expire after 2038-01-19, caused a multiplication that
may overflow the "to" variable of type time_t
Attached patch checks if "to" precedes "from": if so sets "to" to its
maximum value. Pretty rude, but works well even if certificate is set to
expire in a century
Signed-off-by: Federico Fissore <federico@fissore.org>
Patchork: http://patchwork.openwrt.org/patch/3749/
SVN-Revision: 37165
When running OpenWrt within KVM KEY_POWER is generated from the ACPI
button driver when restarting or powering down the VM.
Extend button-hotplug to allow user space handlers for these events.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/3799/
SVN-Revision: 37160
