CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Update patch to remove pipetypes var declaration which was throwing
unused variable warning due to the original patch removing the only use.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw.
Add *page* in the argument list and remove the local variable.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This fixes parsing partition placed after TRX with block-aligned length.
It's important e.g. for Archer C9 which has TRX with kernel only and
rootfs as separated partition.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix build on targets not using CONFIG_MODULE_STRIPPED.
Neither RTL8367_DRIVER_DESC nor RTL8367B_DRIVER_DESC are defined
anywhere. It worked for targets using CONFIG_MODULE_STRIPPED since our
module stripper no-ops the various module info macros.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Change grub's root device to xen/xvda,msdos1 for the x86_xen_domu
target so that it will boot without further changes.
Signed-off-by: Wilfried Klaebe <w+lede-project@chaos.in-kiel.de>
[Jo-Philipp Wich: fixed and rebased patch from FS#264, added subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch refreshes the ipq806x kernel patches.
There was a large PR for ipq806x in the queue when the kernel patches
were refreshed for 4.4.32, so currently there is quite much fuzz for
ipq806x.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a powerful API for parallel crypto from which many other modules
can benefit. It only winds up being turned on on SMP systems, which
means this adds 0 bytes to the kernel on tiny machines, while only
adding a small bit to SMP systems for big performance improvements.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Adds Google's mirror as primary source and kernel.org as fallback.
Same as commit 0d4f02dfd6
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
In Device/ls1012ardb IMAGES variable, there are two separate firmware
references to the same packages, while do mult-job compile, the same package
build process will arise conflict occasionally. So, only reserve one ext4 fs
as the default firmware.bin.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
