Commit graph

226 commits

Author SHA1 Message Date
Deng Qingfang
d20f4fc628 ramips: add support for HiWiFi HC5861B
HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN
https://www.hiwifi.com/enjoy-view

Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7612EN 802.11ac 2T2R 867Mbps
- 5x 10/100 Mbps Ethernet

Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot

Everything is working

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-08-14 10:21:32 +02:00
Daniel Gimpelevich
1d3ea7874d ramips: fix BR-6478ACv2 support
The wholesale changes introduced in commit f9b8328 missed this DTS file
because it hadn't been merged yet. This patch brings it in line to match
the other mt7620a devices' DTS files.

Additionally, the Internet LED is now labeled correctly and set to unused
by default, since the WAN interface is not known in every configuration.

Using sysupgrade between images before and after this commit will require
the -F flag.

Tested-by: Rohan Murch <rohan.murch@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[drop internet led default setting]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-13 08:37:19 +02:00
Ludwig Thomeczek
5543d63fc8 ramips: add support for Netgear R6120
This patch adds support for the Netgear R6120, aka Netgear AC1200.

Specification:
- SoC: MediaTek MT7628 (580 MHz)
- Flash: 16 MiB
- RAM: 64 MiB
- Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E)
- LAN speed: 10/100
- LAN ports: 4
- WAN speed: 10/100
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

To flash use nmrpflash with the provided factory.img.
Flashing via webinterface will not work, for now.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2018-08-13 08:37:19 +02:00
Daniel Gimpelevich
f72fa883b3 ramips: add support for Edimax BR-6478AC v2
Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie.
Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated.

Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Macronix MX25L6405D
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7612E 5GHz 802.11ac
- Switch: Mediatek MT7530W Gigabit Switch
- USB: Yes 1 x 2.0

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
4. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
INAGAKI Hiroshi
ce93445cd6 ramips: add support for ELECOM WRC-2533GST
ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
  - MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-30 15:55:21 +02:00
Ademar Arvati Filho
16d6a63f85 ramips: add support for Blueendless Kimax U35WF
Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet

Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908
Based on: https://github.com/lede-project/source/pull/965

Specification:
- SoC: MediaTek MT7620N
- CPU/Speed: 580 MHz
- Flash-Chip: KH25L12835F Spi Flash
- Flash size: 16 MiB
- RAM: 64 MiB
- LAN: 1x 100 Mbps Ethernet
- WiFi SoC-integrated: 802.11bgn
- 1x USB 2.0
- UART: for serial console

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
3. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-07 21:07:40 +02:00
INAGAKI Hiroshi
0b83a23560 ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Stock firmware:

In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.

(excerpt from dmesg):

MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"

The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.

If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.

(example):

## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1  !!
## Booting image at bc060000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.50
   Image Type:   MIPS Linux kernel Image (lzma compressed)
   Data Size:    1865917 Bytes = 1.8 MB
   Load Address: 80001000
   Entry Point:  80001000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!

Starting kernel ...

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-07 21:07:40 +02:00
Romain MARIADASSOU
ce31bdc20c ramips: add support for TL-WA801ND v5
Specification:

- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn

Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.

Flash instructions:

1) To flash the recovery image, start a TFTP server with IP address
   192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
   button and power it up. Keep pressing the WPS/Reset button for
   10 seconds or until the lock LED is lighting up.
   It will try to download the recovery image and flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-07-04 01:20:02 +02:00
Maxim Anisimov
7d07bc96b7 ramips: add support for ZyXEL Keenetic Extra II
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button

The device supports dual boot mode. So we use only first half of flash.

Flash instruction:

The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
   to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Tobias Schramm
faf64056dd ramips: add support for MikroTik RouterBOARD RBM11g
This commit adds support for the MikroTik RouterBOARD RBM11g.

=Hardware=

The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.

==Switch==

The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.

==Flash==

The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.

==PCIe==

The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.

==USB==

There are no external USB ports.

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.

==Serial port==

The device does have an onboard UART on an unpopulated header next to the
flash chip:

GND: pin 2
 TX: pin 7
 RX: pin 6

Settings: 115200, 8N1

See below illustration for positioning of the header.

0 = screw hole
* = some pin
T = TX  pin
R = RX  pin
G = GND pin

Pinout:
+---------------
|O
|             __
|            /  \
|            \__/
|
|
|
|               +---+
|               |RAM|
| +--+          |   |
| |**|  <- unpopulated header with UART
| |*T|          +---+
| |R*|        +--------+
| |**|        |        |
| |G*|        |  CPU   |
| +--+        |        |
|    +--+     |        |
|    |  |     +--------+
|    +--+  <- flash chip
|O
|       +-----+
|       |     |
|+--+   |     |
||  |   |     |
+---------------------

=Installation=

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**

When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
   initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot

Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
   to the device using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"

Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-07-04 01:20:02 +02:00
Lev
3d6f57f3c6 ramips: fix wizfi630a swapped lan/wan port
The order of the Ethernet ports were mixed up.
This commit fixes the order to be aligned with the physical layout.

Signed-off-by: Lev <leventelist@gmail.com>
2018-07-02 06:59:31 +02:00
INAGAKI Hiroshi
0efd0308a0 ramips: add switch port index for I-O DATA WN-GX300GR
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0

1-4: lan
0: wan

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-27 08:42:54 +02:00
Franz Flasch
8375623a06 ramips: add support for TP-Link Archer C2
Specification:

- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0

Preparing a TFTP recovery image for initial flashing:

Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!

Create a TFTP recovery image:

1) Download a stock TP-Link Firmware file here:
     https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
     #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
     #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin

The resulting image can be flashed via TFTP recovery mode.

Flash instructions:

1) To flash the recovery image, start a TFTP server from IP address
   192.168.0.66 and serve the recovery image named
   ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
   and power it up. Keep pressing the WPS/Reset button for 10 seconds.
   It will try to download the recovery image and flash it.

It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Chuanhong Guo
ed40173dfc ramips: Add support for Phicomm K2G
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-21 22:00:02 +02:00
Tobias Schramm
5684d08741 ramips: Add support for Mikrotik RouterBOARD RBM33g
This commit adds support for the Mikrotik RouterBOARD RBM33g.

=Hardware=

The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.

==Switch==

The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:

port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU

==Flash==

The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.

==PCIe==

The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.

Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:

PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11

==USB==

The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:

open: USB on PCIe 1 is active
closed: USB on rear USB port is active

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.

=Installation=

==Prerequisites==

A USB -> RS-232 Adapter and a null modem cable are required for
installation.

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**

Serial settings: 115200 8N1

The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
   initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
   allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet

On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
   using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"

Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
INAGAKI Hiroshi
189815462c ramips: add support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
  - MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新(アップデート)")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:21 +02:00
Maxim Anisimov
8956eb502d ramips: add support for TP-Link TL-WR842N v5
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch

Flash instruction:

The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-06-16 10:08:51 +02:00
Matthias Badaire
6ea0807f18 ramips: fix network config for ravpower wd03
This device has only one ethernet port.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[add the existing eth0 as lan block, shorten commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-09 13:45:29 +02:00
INAGAKI Hiroshi
a32c06f44d ramips: add support for I-O DATA WN-GX300GR
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.

Specification:

- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Flash instruction using initramfs image:

1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-08 09:56:27 +02:00
Rosen Penev
9685f39787 ramips: Use generic board detect for GnuBee devices
This is a port of an old commit from mkresin's tree:

09260cdf3e9332978c2a474a58e93a6f2b55f4a8

This has the potential to break sysupgrade but it should be fine as
there is no stable release of LEDE or OpenWrt that support these devices.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:36:02 +02:00
YuheiOKAWA
d91953cb53 ramips: add support for YUKAI Engineering Inc. BOCCO
BOCCO is a communication robot provided by YUKAI Engineering Inc.

SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-05-18 11:19:00 +02:00
Davide Ammirata
004cc22e4e ramips: add support for mqmaker witi 512mb version
Splitted out the dts file and create the new dts for the 256 MByte RAM and
the 512 MB RAM version.

Migrate both versions to the common board detection.

The install the 512 MByte Version on a board running the 256 MByte image,
a forceful sysupgrade with the -F flag is required.

Signed-off-by: Davide Ammirata <list@davidea.it>
2018-05-07 18:54:23 +02:00
Matthias Badaire
5ef79af4f8 ramips: add support for Ravpower WD03
The RavPower WD03 is a battery powered SD card reader and a USB port.

Specifications:
SOC:     MediaTek MT7620N
BATTERY: 6000mah
WLAN:    802.11bgn
LAN:     1x 10/100 Mbps Ethernet
USB:     1x USB 2.0 (Type-A)
RAM:     PM Tech PMD708416CTR-5CN 32 MB
FLASH:   Holtek HT66F40 - 8 MB Flash
LED:     Power button and 4 leds to indicate power level of the
         battery (could not get control of that)
INPUT:   Power, reset button
OTHER:   USB SD-Card reader with card detect on GPIO#42

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - installation from tftp
 - OpenWRT sysupgrade (Preserving and non-preserving)
 - LEDs
 - Buttons

Installation:
 - Download the sysupgrade image
 - Place it in the root of a clean TFTP server running on your computer.
 - Rename the image to "kernel" — be sure there is no file extension.
 - Plug the WD03 into your computer via ethernet.
 - Set your computer to use 10.10.10.254 as its IP address.
 - With your WD03 shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The WD03 (10.10.10.128) will look for your computer at 10.10.10.254
   and install the kernel file. Once it has finished installation of the
   kernel file, it will search for a (nonexistent) rootfs file — when it
   begins searching for this file, shut down the WD03 by holding the
   power button normally.
 - Start up your WD03 normally.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-07 18:54:23 +02:00
Vianney le Clément de Saint-Marcq
bcf2125142 ramips: add support for Zorlik ZL5900V2
The Zorlik ZL5900V2 is an unbranded clone of HAME MPR-A1/2.  It is
marketed as "3G Wi-Fi Router".  Only the PCB has the model name
"ZL5900V2" printed on it.

Specifications:
- Ralink RT5350F (360 MHz)
- 32 MB RAM
- 8 MB Flash
- 802.11bgn 1T1R
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (Type-A)
- 5200 mAh battery

The ramdisk image (not the squashfs sysupgrade image) can be flashed
through the web interface (named "GoAhead") of the factory firmware.
However, as the factory firmware does not cleanly unmount the rootfs
before flashing, the device may hang instead of rebooting after
successful write.  Power cycling the device gets you in OpenWrt where
the squashfs image may be flashed through normal sysupgrade procedure.

Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
2018-04-08 09:53:50 +02:00
Zheng Qian
80a94aacaf ramips: add support for the YouHua WR1200JS
YouHua tech WR1200JS is an AC1200 router with 5 1Gb ports (4 Lan, 1 Wan)
and 1 USB 2.0 port.

Devices is base on MediaTek MT7621AT + MT7603E + MT7612E.

Specification:

- MT7612AT (880 MHz)
- 128 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 2T2R 2.4 GHz (MT7603E)
- 2T2R 5 GHz (MT7612E)
- 1x USB 2.0
- 10x LED (Power 2G 5G WPS Internet LAN4-1 USB)
- 3x button (reset wifi wps)
- DC jack for main power input (12V)

Installation:

1.) Press reset key 5 sec and restore the factory default
2.) Login webUI and change username to root and set a
    new password
3.) Visit http://192.168.2.254/adm/telnetd.shtml and
    turn on the telnet service
4.) Copy openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin
    to a usb pan
5.) Plug the usb pan to the router, telnet to the router
    and login by root
6.) cd /media/sda1 and check the initramfs file is there
7.) exec command:
    mtd_write write openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin Kernel
8.) reboot and visit 192.168.1.1

Signed-off-by: Zheng Qian <sotux82@gmail.com>
2018-04-08 09:52:48 +02:00
Giuseppe Lippolis
6525bffc0a ramips: add support for DLINK DWR-921-C1
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
    blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-04 08:42:35 +02:00
INAGAKI Hiroshi
e3bf92edf5 ramips: fix switch and MAC address for WHR-G300N
WHR-G300N has 5 ethernet ports (lan: 4, wan: 1), but there was no
correct configuration in 02_network script and 6 ports was configured
on the switch.
Also, since the MAC address was not acquired from factory partition,
incorrect values was set to LAN and WAN interfaces.

This commit fixes these issues.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-03-23 20:31:49 +01:00
Peter Lundkvist
d13b05741a ramips: add support for TP-Link TL-WR902AC v3
TP-Link TL-WR902AC v3 is a pocket-size dual-band (AC750) router
based on MediaTek MT7628N + MT7650E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet

* MT7650 ac chip isn't not supported by LEDE/OpenWrt at the moment.
  Therefore 5Ghz won' work.

Flash instruction:

The only way to flash LEDE image in TL-WR902AC v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr902ac-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[drop p2led_an pinmux, this pin isn't used as gpio, fix whitespace issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-18 22:22:38 +01:00
Pawel Dembicki
a5bd8de0bd ramips: add support for D-Link DWR-116-A1/2
The DWR-116-A1/2 Wireless Router is based on the MT7620N SoC.

Specification:

  MediaTek MT7620N (580 Mhz)
  32 MB of RAM
  8 MB of FLASH
  802.11bgn radio
  5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  2x external, non-detachable antennas
  UART (J1 in A1, JP1 in A2) header on PCB (57600 8n1)
  6x LED (GPIO-controlled), 2x button
  JBOOT bootloader

Known issues:
WAN LED is drived by uartl tx pin. I decide to use this pin as
uartlite tx pin.

Installation:
Apply factory image via http web-gui.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-03-18 22:22:38 +01:00
INAGAKI Hiroshi
dbdc26ba33 ramips: fix switch for Nexx devices
There are 2 ethernet ports on Nexx WT1520 and WT3020. These ethernet
ports are assigned as follows, and other ports cannot be used.

- WT1520:
  - port0 -> lan
  - port4 -> wan

- WT3020:
  - port0 -> wan
  - port4 -> lan

I dropped ports that cannot be used.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-03-17 08:09:04 +01:00
Roman Yeryomin
f5984e0a0c ramips: mt7621: add Mediatek AP-MT7621A-V60 EVB support
This board has:
- mt7621 SoC
- 8MB SPI flash
- 128MB RAM
- 5x ethernet ports from internal (SoC) switch
- 1x ethernet port sitting on gmac2 and IC+ phy (not yet supported)
- 3x PCIe slots
- 1x USB 2.0 and 1x USB 3.0
- sound based on wm8960
- SDXC card slot (full size)

First fw write from interactive u-boot menu, interrupt with 2.
After that sysupgrade.

Tested both with 4.9 and 4.14

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-02-24 16:05:28 +01:00
Piotr Dymacz
f1c193c27e ramips: add support for ALFA Network AWUSFREE1
ALFA Network AWUSFREE1 is an USB Wi-Fi N300 adapter based on MT7628.

Specification:

- MT7628AN (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (MT7628) with external FEM (RFFM4203)
- 2x detachable antennas (RP-SMA)
- ASIX AX88772 USB to Ethernet bridge (connected with MT7628 PHY0)
- 4x LED (2 driven by GPIO)
- 1x button (reset)
- 1x mini USB for host and main power input
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Power device with reset button pressed and release it after ~5 sec.
2. Setup static IP 192.168.1.2/4 on your PC.
3. Go to 192.168.1.1 in browser and upload "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 23:40:11 +01:00
INAGAKI Hiroshi
e1d4aa36b0 ramips: add support for Tama W06
Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek
MT7688AN.

Specification:

- MT7688AN (575 MHz)
- 64 MB of RAM (DDR2 SDRAM)
- 16 MB of Flash (SPI)
- 1T1R 2.4 GHz
- 1x 10/100/1000 Mbps Ethernet
- 4x LEDs (GPIO connected: 3), 1x button
- 1x USB 2.0 Type-A (host)
- UART header on PCB (GND, RX, TX, Vcc from RJ45 side)

Flash instruction using sysupgrade image:
1. Connect micro-USB cable for power supply into W06 and turn on the
router
2. Connect to wifi with SSID "tama-*" with password. Complete SSID and
password are listed on the back of the router
3. Access to 192.168.1.1 and login with user name "admin" and password
empty
4. In firmware update(ファームウェア更新) page, click "参照" button
and click "ブラウザー" button to open file browser, select the
sysupgrade image and press OK button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-02-20 19:25:17 +01:00
Mathias Kresin
cb741654e5 ramips: improve GnuBee Personal Cloud Two support
Use the generic board detection for the GnuBee Personal Cloud Two
instead of the target specific one as all recent additions are doing.

Fixup the pinmux to set all pins used as GPIO to the function GPIO.
Request pins where used.

Drop the i2c from the dts. There is nothing connected. While at it fix an
indentation issue and use references instead of duplicating the whole
node path.

Use the same switch config as for the GB-PC1 and drop the led trigger for
the not supported IP1001 phy connected to second rgmii.

Fixes: c60a21532b ("ramips: Add support for the GnuBee Personal Cloud Two")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
c330408ea9 ramips: use generic board detection for D-Link DAP-1522 A1
Use the generic board detection for the D-Link DAP-1522 A1 instead of the
target specific one as all recent additions are doing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
George Hopkins
13f9e40602 ramips: add support for D-Link DAP-1522 A1
D-Link DAP-1522 is a wireless bridge/access point with 4 LAN
ports and a dual-band wireless chipset.

Specifications:
- Ralink RT2880
- 32 MB of RAM
- 4 MB of Flash
- 4x 10/100/1000 Mbps Ethernet (RTL8366SR)
- 802.11abgn (RT2850)

Flash Instructions:
1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin
2. Open the web interface and upload the image

Signed-off-by: George Hopkins <george-hopkins@null.net>
2018-02-13 11:18:07 +01:00
Rosen Penev
c60a21532b ramips: Add support for the GnuBee Personal Cloud Two
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.

Specifications:

- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 3.5" Drives
- One SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: Three Ports
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Three GPIOs available on a pin header

Flash instructions:

The GnuBee Personal Cloud Two ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.

Das U-Boot has multiple options for recovery or updates including :

- USB
- http
- tftp

Errata:
- While there are three ethernet ports, the third requires support for
  the second GMAC. This will come in kernel 4.14.
- The first hard drive slot has a clearance issue with the two fan
  headers. Workaround is to pull the headers out and connect the pins to
  jumper wires.
- Using this device as a NAS is problematic with the 4.9 kernel as many
  /dev/sdX reads throw silent errors. The current theory behind this is
  some kind of unhandled DMA mapping error in the kernel. This is not an
  issue with kernel 4.4.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-13 10:01:52 +01:00
Henryk Heisig
14951e8f8e ramips: add support for TP-Link Archer C50 v3
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Flash instruction:

The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Daniel Golle
32f120b783 ramips: various fixes for zbt-we1226
Convert userspace code to use generic device-tree compatible board
detection method.  Users of the existing code will have to use
sysupgrade -F once to switch to the new generic board naming.
Properly setup pinctrl fixing the switch port LEDs.

Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226)
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-02-06 03:00:33 +01:00
Jackson Ming Hu
21d3643828 ramips: add support for Widora Neo 32MB flash revision
Widora has updated their Widora Neo board recently.

The new model uses 32MB WSON-8 factor SPI flash
instead of the original 16MB SOP-8 factor SPI flash.

All the other hardware components are the same as
the first revision.

Detailed hardware specs listed below:

CPU: MTK MT7688AN
RAM: 128MB DDR2
ROM: 32MB WSON-8 factor SPI Flash (Winbond)
WiFi: Built-in 802.11n 150Mbps?
Ethernet: 10/100Mbps x1
Audio codec: WM8960
Other IO: USB OTG;
	  USB Power+Serial (CP2104);
	  3x LEDs (Power, LAN, WiFi);
	  2x Keys (WPS, CPU Reset)
	  1x Audio In/Out
	  1x IPEX antenna port
	  1x Micro SD slot

Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-23 23:31:09 +01:00
Mathias Kresin
a411881a40 ramips: add flash size postfix to Widora neo
Rename the Widora neo by adding a flash size prefix. Move the common parts
into a dtsi to be prepare everything for upcomming support of the 32MB
version.

Migrate the Widora neo to the generic board detection as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-23 23:31:09 +01:00
Daniel Golle
9c4fe103cb ramips: add support for ZBT-WE1226
MT7628NN (580MHz), 8MB SPI NOR, 64MB DDR2 RAM

Everything except for the switch LEDs works great.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-01-23 02:56:57 +01:00
Maxim Anisimov
5bdd238b63 ramips: add support for TP-Link Archer C20 v4
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
  work.

Flash instruction:

The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
Maxim Anisimov
ff1e895530 ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1
This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
Piotr Dymacz
5352669c2c ramips: add support for ALFA Network AC1200RM
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.

Specification:

- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers

Flash instruction (do it under U-Boot, using UART and TFTP server):

Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Chuanhong Guo
a657978fe7 ramips: fix lenovo newifi-y1 switch and LED config
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.

Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.

This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-01-09 22:05:46 +01:00
Henryk Heisig
39e9bfb181 ramips: add support for TP-Link TL-MR3420 v5
TP-Link TL-MR3420 v5 are simple N300 router with
5-port FE switch and non-detachable antennas.
Its very similar to TP-Link TL-WR841N V13.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 8x LED, 2x button, power input switch

Flash instruction:

The only way to flash LEDE image in mr3420v5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-12-23 15:35:52 +01:00
Jackson Ming Hu
c0e131b436 ramips: add support for newifi d2
Previously Newifi D2 could only use PandoraBox M1's firmware.
It works fine, but LED GPIO is different.
As a result, a separated DTS file for this device should be implemented.

Hardware spec:

* CPU: MTK MT7621A
* RAM: 512MB
* ROM: 32MB SPI Flash
* WiFi: MTK MT7603+MT7612
* Button: 2 buttons (reset, wps)
* LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) &
       2 dual-color LEDs (Power, Internet)
* Ethernet: 5 ports, 4 LAN + 1 WAN

Installation method:

Same as Newifi D1, users may need to request unlock code from the device
manufacturer. Otherwise, a SPI flash programmer may be necessary to get
the firmware flashed. After the device is unlocked, press and hold reset
button before power cable plugs in. Then go to http://192.168.1.1 to
upload and flash the firmware package.

Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
2017-12-21 01:05:16 +01:00
Andrew Crawley
fe6f298b07 ramips: add support for Vonets VAR11N-300
The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet
cable, one extra Ethernet port, and an internal antenna, based on the
MediaTek MT7620n chipset.

Specs:
- MT7620n WiSoC @ 600MHz
- 32 MB SDRAM
- 4 MB SPI flash
- 2T2R 2.4GHz WiFi-N
- 1 attached 10/100 Ethernet cable (LAN)
- 1 10/100 Ethernet port (WAN)
- 1 attached USB / barrel 5vdc power cable
- 5 LEDs (see notes below)
- 1 reset button
- 1 UART (3 pads on board)

Installation:

The stock firmware does not support uploading new firmware directly,
only checking the manufacturer's site for updates.  This process may be
possible to spoof, but the update check uses some kind of homebrew
encryption that I didn't investigate.  Instead, you can install via a
backdoor:

1. Set up a TFTP server to serve the firmware binary
(lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin)
2. Factory reset the device by holding the reset button for a few
seconds.
3. Open the web interface (default IP: 192.168.253.254)
4. Log in with the "super admin" credentials: username `vonets`,
password `vonets26642519`.
5. On the "Operative Status" page, click the text "System Uptime", then
quickly click the uptime value.
6. If successful, an alert dialog will appear reading "Ated start", and
the device will now accept telnet connections.  If the alert does not
appear, repeat step 5 until it works (the timing is a bit tricky).
7. Telnet to the device using credentials "admin / admin"
8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin
-r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g
<tftp-server-ip>`
9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4`
10. Reboot

Tested:
- LAN / WAN ethernet
- WiFi
- LAN / WAN / status LED GPIOs (see notes below)
- Reset button
- Sysupgrade

Notes:

LEDs:

The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue
LED for WiFi, and a pair of "status" LEDs connected to the same GPIO
(the blue LED lights when the GPIO is low, and the green when it's
high).  I was unable to determine how to operate the WiFi LED, as it
does not appear to be controlled by a GPIO directly.

Recovery:

The default U-boot installation will only boot from flash due to a
missing environment block.  I generated a valid 4KB env block using
U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an
external programmer.  After this, it was possible to enter the U-boot
commandline interface and download a new image via TFTP (`tftpboot
81b00000 <image-filename>`), but while I could boot this image
sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted
the flash chip.  The sysupgrade file can be written to flash at 0x50000
using an external programmer.

Signed-off-by: Andrew Crawley <acrawley@gmail.com>
2017-12-21 01:05:16 +01:00
Mathias Kresin
7d3ec5f833 ramips: fallback to generic board detect
Fallback to the generic board detection if no case for the current
board exists.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-21 01:05:16 +01:00