0b83a23560
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Stock firmware:
In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.
(excerpt from dmesg):
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.
If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.
(example):
## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1 !!
## Booting image at bc060000 ...
Image Name: MIPS OpenWrt Linux-4.14.50
Image Type: MIPS Linux kernel Image (lzma compressed)
Data Size: 1865917 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!
Starting kernel ...
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
594 lines
11 KiB
Bash
Executable file
594 lines
11 KiB
Bash
Executable file
#!/bin/sh
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ramips_setup_rt3x5x_vlans()
|
|
{
|
|
if [ ! -x /sbin/swconfig ]; then
|
|
# legacy default
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
return
|
|
fi
|
|
local wanports=""
|
|
local lanports=""
|
|
for port in 5 4 3 2 1 0; do
|
|
if [ `swconfig dev rt305x port $port get disable` = "1" ]; then
|
|
continue
|
|
fi
|
|
if [ `swconfig dev rt305x port $port get lan` = "0" ]; then
|
|
wanports="$port:wan $wanports"
|
|
else
|
|
lanports="$port:lan $lanports"
|
|
fi
|
|
done
|
|
ucidef_add_switch "rt305x" $lanports $wanports "6t@eth0"
|
|
}
|
|
|
|
ramips_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case $board in
|
|
11acnas|\
|
|
w2914nsv2|\
|
|
zbt-we2026)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6@eth0"
|
|
;;
|
|
3g150b|\
|
|
3g300m|\
|
|
a5-v11|\
|
|
all0256n-4M|\
|
|
all0256n-8M|\
|
|
all5002|\
|
|
all5003|\
|
|
bocco|\
|
|
broadway|\
|
|
dcs-930|\
|
|
dcs-930l-b1|\
|
|
ht-tm02|\
|
|
linkits7688 | \
|
|
m2m|\
|
|
microwrt|\
|
|
mikrotik,rbm11g|\
|
|
mpr-a2|\
|
|
ncs601w|\
|
|
omega2 | \
|
|
omega2p | \
|
|
timecloud|\
|
|
tplink,tl-wa801nd-v5|\
|
|
w150m|\
|
|
widora,neo-16m|\
|
|
widora,neo-32m|\
|
|
wnce2001|\
|
|
zbt-cpe102|\
|
|
zorlik,zl5900v2|\
|
|
zte-q7)
|
|
ucidef_add_switch "switch0"
|
|
ucidef_add_switch_attr "switch0" "enable" "false"
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
mlw221|\
|
|
mr-102n)
|
|
ucidef_set_interface_lan "eth0.2"
|
|
;;
|
|
3g-6200n|\
|
|
ai-br100|\
|
|
alfa-network,ac1200rm|\
|
|
mediatek,ap-mt7621a-v60|\
|
|
d240|\
|
|
db-wrt01|\
|
|
dir-300-b7|\
|
|
dir-320-b1|\
|
|
dir-610-a1|\
|
|
dir-615-h1|\
|
|
dlink,dwr-116-a1|\
|
|
dlink,dwr-921-c1|\
|
|
ew1200|\
|
|
firewrt|\
|
|
hc5661a|\
|
|
hc5962|\
|
|
hlk-rm04|\
|
|
k2p|\
|
|
kn|\
|
|
kn_rc|\
|
|
mac1200rv2|\
|
|
miwifi-mini|\
|
|
miwifi-nano|\
|
|
mt7621|\
|
|
mt7628|\
|
|
mzk-750dhp|\
|
|
mzk-w300nh2|\
|
|
d-team,newifi-d2|\
|
|
nixcore-x1-8M|\
|
|
nixcore-x1-16M|\
|
|
oy-0001|\
|
|
pbr-m1|\
|
|
psg1208|\
|
|
psg1218a|\
|
|
r6220|\
|
|
rt-n12p|\
|
|
sap-g3200u3|\
|
|
sk-wb8|\
|
|
u7621-06-256M-16M|\
|
|
vr500|\
|
|
wf-2881|\
|
|
whr-g300n|\
|
|
mqmaker,witi-256m|\
|
|
mqmaker,witi-512m|\
|
|
wl-wn575a3|\
|
|
wndr3700v5|\
|
|
youku-yk1|\
|
|
zbt-ape522ii|\
|
|
zbt-we1326|\
|
|
zbtlink,zbt-we3526|\
|
|
zbt-we826-16M|\
|
|
zbt-we826-32M|\
|
|
zbt-wg2626|\
|
|
zbt-wg3526-16M|\
|
|
zbt-wg3526-32M|\
|
|
zbt-wr8305rt)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
alfa-network,awusfree1|\
|
|
cs-qr10|\
|
|
d105|\
|
|
dlink,dap-1522-a1|\
|
|
dch-m225|\
|
|
ex2700|\
|
|
ex3700|\
|
|
hpm|\
|
|
mzk-ex300np|\
|
|
mzk-ex750np|\
|
|
na930|\
|
|
pbr-d1|\
|
|
ravpower,wd03|\
|
|
tama,w06|\
|
|
u25awf-h1|\
|
|
wli-tx4-ag300n|\
|
|
wmdr-143n|\
|
|
wmr-300|\
|
|
wn3000rpv3|\
|
|
wrh-300cr)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
mir3g)
|
|
ucidef_add_switch "switch0" \
|
|
"2:lan:2" "3:lan:1" "1:wan" "6t@eth0"
|
|
;;
|
|
psg1218b)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:3" "1:lan:2" "2:lan:1" "3:wan" "6@eth0"
|
|
;;
|
|
whr-300hp2|\
|
|
whr-600d|\
|
|
wsr-1166|\
|
|
wsr-600)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "4:wan:5" "6@eth0"
|
|
;;
|
|
ar670w|\
|
|
ar725w|\
|
|
rt-ac51u)
|
|
ucidef_add_switch "switch0" \
|
|
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
|
|
;;
|
|
rt-n15|\
|
|
wl-351)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
|
|
;;
|
|
asl26555-8M|\
|
|
asl26555-16M|\
|
|
rp-n53)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
|
|
;;
|
|
atp-52b|\
|
|
awm002-evb-4M|\
|
|
awm002-evb-8M|\
|
|
c20i|\
|
|
dir-645|\
|
|
f5d8235-v2|\
|
|
gl-mt300a|\
|
|
gl-mt300n|\
|
|
gl-mt750|\
|
|
hg255d|\
|
|
jhr-n805r|\
|
|
jhr-n825r|\
|
|
jhr-n926r|\
|
|
mikrotik,rbm33g|\
|
|
mzk-wdpr|\
|
|
rb750gr3|\
|
|
rt-n14u|\
|
|
tplink,c20-v4|\
|
|
tplink,c50-v3|\
|
|
tplink,tl-mr3420-v5|\
|
|
tplink,tl-wr842n-v5|\
|
|
tl-wr840n-v4|\
|
|
tl-wr840n-v5|\
|
|
tl-wr841n-v13|\
|
|
u7628-01-128M-16M|\
|
|
ubnt-erx|\
|
|
ubnt-erx-sfp|\
|
|
ur-326n4g|\
|
|
wrtnode|\
|
|
wrtnode2p | \
|
|
wrtnode2r | \
|
|
youhua,wr1200js|\
|
|
zbt-wa05|\
|
|
zyxel,keenetic-extra-ii)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
c50|\
|
|
tplink,c20-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0"
|
|
;;
|
|
dir-860l-b1|\
|
|
elecom,wrc-1167ghbk2-s|\
|
|
iodata,wn-ax1167gr|\
|
|
iodata,wn-gx300gr)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
|
|
;;
|
|
gnubee,gb-pc1|\
|
|
gnubee,gb-pc2)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "4:lan" "6@eth0"
|
|
;;
|
|
gl-mt300n-v2)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "0:wan" "6@eth0"
|
|
;;
|
|
awapn2403)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:wan" "6@eth0"
|
|
;;
|
|
b2c|\
|
|
nw718|\
|
|
psr-680w|\
|
|
sl-r7205|\
|
|
ur-336un|\
|
|
w502u|\
|
|
wr6202)
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
;;
|
|
br-6475nd)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
|
|
;;
|
|
c108|\
|
|
cf-wr800n)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "6t@eth0"
|
|
;;
|
|
cy-swr1100)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9@eth0"
|
|
;;
|
|
duzun-dm06)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "0:wan" "6@eth0"
|
|
;;
|
|
e1700|\
|
|
mt7620a_mt7530)
|
|
ucidef_add_switch "switch1" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
hc5*61|\
|
|
y1s)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0"
|
|
;;
|
|
kn_rf)
|
|
ucidef_add_switch "switch0" \
|
|
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"
|
|
;;
|
|
kng_rc)
|
|
ucidef_add_switch "switch1" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "7t@eth0"
|
|
;;
|
|
mlwg2|\
|
|
wizard8800|\
|
|
wl-330n)
|
|
ucidef_set_interface_lan "eth0.1"
|
|
;;
|
|
mr200)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0"
|
|
ucidef_set_interface_wan "usb0"
|
|
;;
|
|
mzk-dp150n|\
|
|
vocore-8M|\
|
|
vocore-16M)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "4:lan" "6t@eth0"
|
|
;;
|
|
newifi-d1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan:2" "2:lan:1" "4:wan" "6@eth0"
|
|
;;
|
|
phicomm,k2g)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5:wan" "6@eth0"
|
|
;;
|
|
re350-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "6@eth0"
|
|
;;
|
|
re6500)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "6@eth0"
|
|
;;
|
|
rt-n56u)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0"
|
|
;;
|
|
tew-638apb-v2)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "6@eth0"
|
|
;;
|
|
tew-691gr|\
|
|
tew-692gr|\
|
|
wlr-6000)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
|
|
;;
|
|
tplink,c2-v1)
|
|
ucidef_add_switch "switch1" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
tplink,tl-wr902ac-v3)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "6@eth0"
|
|
;;
|
|
vonets,var11n-300|\
|
|
wt1520-4M|\
|
|
wt1520-8M)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "4:wan" "6@eth0"
|
|
;;
|
|
vocore2|\
|
|
vocore2lite)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "2:lan" "6t@eth0"
|
|
;;
|
|
f5d8235-v1|\
|
|
tew-714tru|\
|
|
v11st-fe|\
|
|
wzr-agl300nh)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
|
|
;;
|
|
wcr-1166ds)
|
|
ucidef_add_switch "switch0" \
|
|
"3:lan" "4:wan" "6@eth0"
|
|
;;
|
|
wcr-150gn|\
|
|
we1026-5g-16m)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "6t@eth0"
|
|
;;
|
|
whr-1166d)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "5:wan" "6@eth0"
|
|
;;
|
|
wizfi630a)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:wan" "6@eth0"
|
|
;;
|
|
wt3020-4M|\
|
|
wt3020-8M)
|
|
ucidef_add_switch "switch0" \
|
|
"4:lan" "0:wan" "6@eth0"
|
|
;;
|
|
zbtlink,zbt-we1226|\
|
|
y1)
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:2" "1:lan:1" "4:wan" "6@eth0"
|
|
;;
|
|
*)
|
|
RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
|
|
if [ -n "${RT3X5X}" ]; then
|
|
ramips_setup_rt3x5x_vlans
|
|
else
|
|
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
|
|
fi
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ramips_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
|
|
case $board in
|
|
a5-v11|\
|
|
ht-tm02|\
|
|
wmdr-143n)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
;;
|
|
all0239-3g|\
|
|
carambola|\
|
|
freestation5|\
|
|
w502u|\
|
|
wnce2001)
|
|
wan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
bc2|\
|
|
broadway|\
|
|
d105|\
|
|
dir-300-b7|\
|
|
dir-320-b1|\
|
|
dir-620-a1|\
|
|
esr-9753|\
|
|
freestation5|\
|
|
hlk-rm04|\
|
|
mpr-a1|\
|
|
psr-680w|\
|
|
sl-r7205|\
|
|
y1|\
|
|
y1s)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_setbit_la "$lan_mac")
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
br-6475nd)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(mtd_get_mac_binary devdata 7)
|
|
;;
|
|
cy-swr1100|\
|
|
dch-m225)
|
|
lan_mac=$(mtd_get_mac_ascii factory lanmac)
|
|
;;
|
|
dir-645)
|
|
lan_mac=$(mtd_get_mac_ascii nvram lanmac)
|
|
wan_mac=$(mtd_get_mac_ascii nvram wanmac)
|
|
;;
|
|
dir-860l-b1)
|
|
lan_mac=$(mtd_get_mac_ascii factory lanmac)
|
|
wan_mac=$(mtd_get_mac_ascii factory wanmac)
|
|
;;
|
|
dlink,dwr-116-a1|\
|
|
dlink,dwr-921-c1)
|
|
wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
e1700)
|
|
wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
|
|
;;
|
|
elecom,wrc-1167ghbk2-s|\
|
|
sk-wb8)
|
|
wan_mac=$(mtd_get_mac_binary factory 57350)
|
|
;;
|
|
gl-mt300n-v2|\
|
|
whr-g300n)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
;;
|
|
hc5*61|\
|
|
hc5661a|\
|
|
hc5962)
|
|
lan_mac=`mtd_get_mac_ascii bdinfo "Vfac_mac "`
|
|
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
iodata,wn-ax1167gr|\
|
|
iodata,wn-gx300gr)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary Factory 4)" 1)
|
|
;;
|
|
kn_rc|\
|
|
kn_rf|\
|
|
kng_rc)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
linkits7688)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
mac1200rv2)
|
|
lan_mac=$(mtd_get_mac_binary factory_info 13)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
mir3g)
|
|
lan_mac=$(mtd_get_mac_binary Factory 0xe006)
|
|
;;
|
|
miwifi-mini)
|
|
wan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_setbit_la "$wan_mac")
|
|
;;
|
|
m3|\
|
|
m4-4M|\
|
|
m4-8M|\
|
|
x5|\
|
|
x8)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_add "$lan_mac" -2)
|
|
;;
|
|
newifi-d1)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_add "$lan_mac" 2)
|
|
;;
|
|
omega2|\
|
|
omega2p)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
oy-0001|\
|
|
phicomm,k2g)
|
|
lan_mac=$(mtd_get_mac_binary factory 40)
|
|
wan_mac=$(mtd_get_mac_binary factory 46)
|
|
;;
|
|
r6220)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
rt-n56u)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
lan_mac=$(macaddr_setbit_la "$lan_mac")
|
|
wan_mac=$(mtd_get_mac_binary factory 32772)
|
|
;;
|
|
tew-691gr)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3)
|
|
;;
|
|
tew-692gr)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 1)
|
|
;;
|
|
tiny-ac)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env LAN_MAC_ADDR)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env WAN_MAC_ADDR)
|
|
;;
|
|
vr500)
|
|
lan_mac=$(mtd_get_mac_binary factory 57344)
|
|
wan_mac=$(mtd_get_mac_binary factory 57350)
|
|
;;
|
|
w306r-v20)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 5)
|
|
;;
|
|
wcr-1166ds|\
|
|
wsr-1166)
|
|
local index="$(find_mtd_index "board_data")"
|
|
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
|
|
lan_mac=$wan_mac
|
|
;;
|
|
wcr-150gn)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
whr-1166d|\
|
|
whr-300hp2|\
|
|
whr-600d|\
|
|
wsr-600)
|
|
wan_mac=$(mtd_get_mac_binary factory 4)
|
|
lan_mac=$wan_mac
|
|
;;
|
|
wizfi630a)
|
|
lan_mac=$(mtd_get_mac_binary factory 4)
|
|
wan_mac=$(mtd_get_mac_binary factory 40)
|
|
;;
|
|
wlr-6000)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2)
|
|
;;
|
|
*)
|
|
lan_mac=$(cat /sys/class/net/eth0/address)
|
|
wan_mac=$(macaddr_add "$lan_mac" 1)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ramips_setup_interfaces $board
|
|
ramips_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|