This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)
Flash instruction:
Use sysupgrade in vendor firmare which is based on OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers
Default configuration:
- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.
Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB
AP143 platform, similar to tl-wr841n v10/v11, but with USB
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.
Signed-off-by: P.Wassi <p.wassi at gmx.at>
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 49157
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
This patch supersedes the v1 from September 17th.
Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.
The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).
Fixed items:
- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.
Compiles fine, has been confirmed working by owners on 15.05.
Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?
Thank you
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 47234
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47221
This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro.
Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com>
SVN-Revision: 46961
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45553
None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.
SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
SVN-Revision: 45328
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44620
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44426
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44359
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44255
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
the GPIO controlling the rf filter is not configured properly by this patch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44077
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42914
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 42897
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
This patch adds support for the Ubiquiti Networks airGateway.
Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41766
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
