This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Add back support for the independent_clocks definition that has been
removed between kernel 4.4 and 4.9 by upstream commits
eb96924acddc709db58221c210ca05cd9effb1df and
e86eee6bc2aaa6b3637f6497b26beee09a91bde9
* extend the new cpufreq_dt_platform_data definition in cpufreq-dt.h
* revert the removal of its usage in cpufreq-dt.c
* use new cpufreq-dt.h in qcom-cpufreq.c
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
At the moment as a workaround definition for scm firmware in DT is used as if it is
apq8064 board. This leads to incomplete scm firmware initialization and as a result
cpuidle driver fails to configure.
By design unlike other qcom boards ipq do not use clocks to connect to scm.
Considering this we're removing from DT and scm driver clocks for ipq boards.
As a result cpuidle does not produce errors about failed configuration anymore.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The available amount of coherent DMA memory is very limited. On Linux
4.4 this issue was worked around by increasing the pool size.
It turns out that using coherent memory here is completely unnecessary.
This change reworks the driver code to use kzalloc+dma_map_single
instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not patch upstream files, overwrite them entirely. The upstream files
are buggy for a number of devices and this significantly simplifies the
patch structure
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
The more straight forward approach for generating the pure and unpadded
kernel file which then can be used for initramfs straight.
Build options for factory.img and sysupgrade.tar are handeled
seperately.
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.
Fixes: FS#542
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.
Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.
Runtime-tested on ar71xx, octeon, ramips and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.
Fixes: FS#451
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The setting mmc-ddr-1_8v in the platform dts leads to read errors. The
device is unusable and system reboots in a loop. Because NBG6817 is the
only mmc device, I removed it in base dts.
The second change removes settings now present in base dts.
The third change references was a wrong conversion of constants in the switch settings.
Switch now initializes again.
Signed-off-by: André Valentin <avalentin@marcant.net>
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.
This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.
Signed-off-by: Zhang Jingye <934526987@qq.com>
At the moment we have 2 seperate device tree sources: 1 for ipq8064 soc located
in kernel source and 1 custom in LEDE for ipq8065.
ipq8064 and ipq8065 SoCs are completely identical except ipq8065 has higher cpu
frequencies and adjusted corresponding power supply.
This commit makes ipq8065 DTS to contain only specific for ipq8065 DT entries while
pulling all the basic SoC stuff from ipq8064 DTS.
It makes easier to manage ipq806x device trees and instead of committing changes into
2 seperate equal DTS we are ending up with only 1.
It also enables ipq8065 devices to automatically receive changes made in upstream kernel.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
According to Qualcomm SDK usb3 phy suspend should be disabled for
ipq806x.
This may solve issue on some ipq806x devices that breaks usb3
storage peripherals during system boot.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Fixing pvs1 bin voltage as found in GPL tarball and Qualcomm SDK.
Also adjusting smb208_s2a/b minimum voltage to reflect lowest value in pvs table.
Current ipq8065 devices in LEDE choose (based on eFuse data) pvs bin n4, that has
correct values in DT, but in future a new device may choose n1 or n6.
Without this change n1 is semi-correct and n6 is not available, because OPP driver
disregards bins with voltage values that regulator cannot supply.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
RPM clock controller driver had made its way upstream and previous
approach of directly redoing a driver to support ipq806x is a no go anymore.
Thus reverting mentioned patches to upstream state and renaming
in correct patch numbering accordance.
To make the driver work on ipq806x boards we introduce a custom patch.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Refresh patches on all 4.4 supported platforms.
077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.
Compile & run tested: ar71xx - Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.
Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.
Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.
If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.
Use the usb pinmux settings from the nbg6817 gpl sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).
This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.
Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.
Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.
Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.
Change gpioexport to gpio pinmux.
Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.
Remove pcie pinmux from D7800.
Move pinctrl to correct place in NBG6817 and R7800.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
This patch refreshes the ipq806x kernel patches.
There was a large PR for ipq806x in the queue when the kernel patches
were refreshed for 4.4.32, so currently there is quite much fuzz for
ipq806x.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver
Also switching to ondemand frequency scaling as it is fixed now
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO
For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f
For debugging serial console is easily visible on board, no soldering needed.
Signed-off-by: André Valentin <avalentin@marcant.net>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
-add spi pins
-move mdio and rgmii pinctrl from gmac and mdio into pinmux node
-add i2c4 pinctrl into rpm node
-add pin details into several nodes
-update gmac1 and gmac2 parameters
-update mdio phy0 and phy4 registers by ddwrt devs findings
-fix i2c4 pin drive-strengh
-remove pcie pins as it's already present in ipq8065 DT
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The R7800 is an IPQ8065, so rename its dts file to reflect that fact.
Also fold the R7500v2 dts addition into the existing 800-devicetree.patch.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes instability/corruption on the ethernet interface connected to port0 on the switch on Netgear R7800 as well.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The ATB DTB mangle code will enter an infinite loop if it encounters a
word in the command line that contains an r in the middle of the word.
Fix this by increasing ptr everytime before invoking strchr, ot avoid
finding the same r again.
This fixes booting at least on Netgear R7500v1, which contains
"ubi.mtd=rootfs" in its commandline, triggering the misbehaviour.
Fixes: 0ddcbee261 ("ipq806x: activate ATAG DTB mangle and EA8500 rootblock in dts")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Calibration data for QCA99x0 in this device has bogus macaddress.
The data cannot be modified directly, as it breaks checksum control.
Instead change the macaddress from phy add hotplug event.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
The command-line arguments provided by the boot loader will be
appended to a new device tree property: bootloader-args.
If there is a property "append-rootblock" in DT under /chosen
and a root= option in bootloaders command line it will be parsed
and added to DT bootargs with the form: <append-rootblock>XX.
Only command line ATAG will be processed, the rest of the ATAGs
sent by bootloader will be ignored.
This is usefull in dual boot systems, to get the current root partition
without afecting the rest of the system.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
This reverts commit 53147c2237.
These config changes break booting on C2600 and probably other devices.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
In commit "regulator: qcom: Rework to single platform device" the smb208
regulator used in IPQ8064 was left out.
Add it to that new framework and update Docs and DT accordingly.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
1)Changes
- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime
2)Testing
Tested on IPQ AP148 Board:
a. NOR boot and NAND boot
b. ethernet network and ath10k wifi
c. ubi sysupgrade
UnTested
dwc3 usb has not been validated on IPQ board(AP148)
3)Known Issues:
Once we flash ubi image on AP148, and if we reset the board, uboot on
first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
and not what linux expects which causes errors when trying to mount rootfs.
In order to test this, we can use the below steps:
a. Flash the ubi image on board and don't reset the board
b. load the kernel fit image in RAM and boot from there.
Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
AP148 uses lowercase name as boardname, so we need to use this in
platform.sh as well.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48304
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Eth0 is attached to mac0 of the switch with a fixed link and and not to
phy4 in single phy mode, so configuring it to anything but 1000FD will
break the connection, which will happen if a only 100 Mbit capapble device
is plugged into the wan port.
Fix this by not taking the state from phy4 and just configuring a fixed link
for eth0.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47695
