ipq806x: add initial support for Netgear R7800

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This commit is contained in:
Pavel Kubelun 2016-06-21 11:55:00 +02:00 committed by John Crispin
parent 9bf3ddcb2a
commit 823242185b
10 changed files with 1597 additions and 12 deletions

View file

@ -19,13 +19,14 @@ c2600)
ucidef_set_led_default "general" "general" "ledgnr:blue" "1"
;;
d7800 |\
r7500)
ucidef_set_led_usbdev "usb1" "USB 1" "r7500:white:usb1" "1-1"
ucidef_set_led_usbdev "usb2" "USB 2" "r7500:white:usb3" "3-1"
ucidef_set_led_netdev "wan" "WAN" "r7500:white:wan" "eth0"
ucidef_set_led_ide "esata" "eSATA" "r7500:amber:esata"
ucidef_set_led_default "wps" "WPS" "r7500:white:wps" "0"
ucidef_set_led_default "rfkill" "rfkill" "r7500:white:rfkill" "0"
r7500 |\
r7800)
ucidef_set_led_usbdev "usb1" "USB 1" "${board}:white:usb1" "1-1"
ucidef_set_led_usbdev "usb2" "USB 2" "${board}:white:usb3" "3-1"
ucidef_set_led_netdev "wan" "WAN" "${board}:white:wan" "eth0"
ucidef_set_led_ide "esata" "eSATA" "${board}:amber:esata"
ucidef_set_led_default "wps" "WPS" "${board}:white:wps" "0"
ucidef_set_led_default "rfkill" "rfkill" "${board}:white:rfkill" "0"
;;
ea8500)
ucidef_set_led_wlan "wifi" "WIFI" "ea8500:green:wifi" "phy0radio"

View file

@ -16,7 +16,8 @@ case "$board" in
ap148 |\
c2600 |\
d7800 |\
r7500)
r7500 |\
r7800)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
;;

View file

@ -56,6 +56,9 @@ case "$FIRMWARE" in
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ath10kcal_extract "art" 4096 12064
;;
r7800)
ath10kcal_extract "art" 4096 12064
;;
esac
;;
"ath10k/cal-pci-0001:01:00.0.bin")
@ -68,6 +71,9 @@ case "$FIRMWARE" in
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ath10kcal_extract "art" 20480 12064
;;
r7800)
ath10kcal_extract "art" 20480 12064
;;
esac
;;
*)

View file

@ -32,6 +32,9 @@ ipq806x_board_detect() {
*"Linksys EA8500"*)
name="ea8500"
;;
*"R7800")
name="r7800"
;;
esac
[ -z "$name" ] && name="unknown"

View file

@ -9,7 +9,8 @@ platform_check_image() {
ap148 |\
d7800 |\
ea8500 |\
r7500)
r7500 |\
r7800)
nand_do_platform_check $board $1
return $?;
;;
@ -32,7 +33,8 @@ platform_pre_upgrade() {
case "$board" in
ap148 |\
d7800 |\
r7500)
r7500 |\
r7800)
nand_do_upgrade "$1"
;;
ea8500)

View file

@ -0,0 +1,372 @@
#include "qcom-ipq8065-v1.0.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "Netgear Nighthawk X4S R7800";
compatible = "netgear,r7800", "qcom,ipq8065";
memory@0 {
reg = <0x42000000 0x1e000000>;
device_type = "memory";
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
rsvd@41200000 {
reg = <0x41200000 0x300000>;
no-map;
};
};
aliases {
serial0 = &uart4;
mdio-gpio0 = &mdio0;
};
chosen {
bootargs = "rootfstype=squashfs noinitrd";
linux,stdout-path = "serial0:115200n8";
};
soc {
pinmux@800000 {
i2c4_pins: i2c4_pinmux {
pins = "gpio12", "gpio13";
function = "gsbi4";
bias-disable;
};
pcie0_pins: pcie0_pinmux {
mux {
pins = "gpio3";
function = "pcie1_rst";
drive-strength = <12>;
bias-disable;
};
};
pcie1_pins: pcie1_pinmux {
mux {
pins = "gpio48";
function = "pcie2_rst";
drive-strength = <12>;
bias-disable;
};
};
nand_pins: nand_pins {
mux {
pins = "gpio34", "gpio35", "gpio36",
"gpio37", "gpio38", "gpio39",
"gpio40", "gpio41", "gpio42",
"gpio43", "gpio44", "gpio45",
"gpio46", "gpio47";
function = "nand";
drive-strength = <10>;
bias-disable;
};
pullups {
pins = "gpio39";
bias-pull-up;
};
hold {
pins = "gpio40", "gpio41", "gpio42",
"gpio43", "gpio44", "gpio45",
"gpio46", "gpio47";
bias-bus-hold;
};
};
mdio0_pins: mdio0_pins {
mux {
pins = "gpio0", "gpio1";
function = "gpio";
drive-strength = <8>;
bias-disable;
};
};
rgmii2_pins: rgmii2_pins {
mux {
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
function = "rgmii2";
drive-strength = <8>;
bias-disable;
};
};
};
gsbi@16300000 {
qcom,mode = <GSBI_PROT_I2C_UART>;
status = "ok";
serial@16340000 {
status = "ok";
};
/*
* The i2c device on gsbi4 should not be enabled.
* On ipq806x designs gsbi4 i2c is meant for exclusive
* RPM usage. Turning this on in kernel manifests as
* i2c failure for the RPM.
*/
};
sata-phy@1b400000 {
status = "ok";
};
sata@29000000 {
status = "ok";
};
phy@100f8800 { /* USB3 port 1 HS phy */
status = "ok";
};
phy@100f8830 { /* USB3 port 1 SS phy */
status = "ok";
};
phy@110f8800 { /* USB3 port 0 HS phy */
status = "ok";
};
phy@110f8830 { /* USB3 port 0 SS phy */
status = "ok";
};
usb30@0 {
status = "ok";
};
usb30@1 {
status = "ok";
};
pcie0: pci@1b500000 {
status = "ok";
reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_pins>;
pinctrl-names = "default";
};
pcie1: pci@1b700000 {
status = "ok";
reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_pins>;
pinctrl-names = "default";
};
nand@1ac00000 {
status = "ok";
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
nand-ecc-strength = <4>;
nand-bus-width = <8>;
#address-cells = <1>;
#size-cells = <1>;
qcadata@0 {
label = "qcadata";
reg = <0x0000000 0x0c80000>;
read-only;
};
APPSBL@c80000 {
label = "APPSBL";
reg = <0x0c80000 0x0500000>;
read-only;
};
APPSBLENV@1180000 {
label = "APPSBLENV";
reg = <0x1180000 0x0080000>;
read-only;
};
art: art@1200000 {
label = "art";
reg = <0x1200000 0x0140000>;
read-only;
};
artbak: art@1340000 {
label = "artbak";
reg = <0x1340000 0x0140000>;
read-only;
};
kernel@1480000 {
label = "kernel";
reg = <0x1480000 0x0200000>;
};
ubi@1680000 {
label = "ubi";
reg = <0x1680000 0x1E00000>;
};
netgear@3480000 {
label = "netgear";
reg = <0x3480000 0x4480000>;
read-only;
};
reserve@7900000 {
label = "reserve";
reg = <0x7900000 0x0700000>;
read-only;
};
firmware@1480000 {
label = "firmware";
reg = <0x1480000 0x2000000>;
};
};
mdio0: mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
pinctrl-0 = <&mdio0_pins>;
pinctrl-names = "default";
phy0: ethernet-phy@0 {
device_type = "ethernet-phy";
reg = <0>;
qca,ar8327-initvals = <
0x00004 0x7600000 /* PAD0_MODE */
0x00008 0x1000000 /* PAD5_MODE */
0x0000c 0x80 /* PAD6_MODE */
0x000e4 0xaa545 /* MAC_POWER_SEL */
0x000e0 0xc74164de /* SGMII_CTRL */
0x0007c 0x4e /* PORT0_STATUS */
0x00094 0x4e /* PORT6_STATUS */
>;
};
phy4: ethernet-phy@4 {
device_type = "ethernet-phy";
reg = <4>;
};
};
gmac1: ethernet@37200000 {
status = "ok";
phy-mode = "rgmii";
qcom,id = <1>;
pinctrl-0 = <&rgmii2_pins>;
pinctrl-names = "default";
mtd-mac-address = <&art 6>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
gmac2: ethernet@37400000 {
status = "ok";
phy-mode = "sgmii";
qcom,id = <2>;
mtd-mac-address = <&art 0>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
gpio-keys {
compatible = "gpio-keys";
wifi {
label = "wifi";
gpios = <&qcom_pinmux 6 1>;
linux,code = <KEY_WLAN>;
};
reset {
label = "reset";
gpios = <&qcom_pinmux 54 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&qcom_pinmux 65 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
gpio-leds {
compatible = "gpio-leds";
usb1 {
label = "r7800:amber:usb1";
gpios = <&qcom_pinmux 7 0>;
};
usb3 {
label = "r7800:amber:usb3";
gpios = <&qcom_pinmux 8 0>;
};
status {
label = "r7800:amber:status";
gpios = <&qcom_pinmux 9 0>;
};
internet {
label = "r7800:white:internet";
gpios = <&qcom_pinmux 22 0>;
};
wan {
label = "r7800:white:wan";
gpios = <&qcom_pinmux 23 0>;
};
wps {
label = "r7800:white:wps";
gpios = <&qcom_pinmux 24 0>;
};
esata {
label = "r7800:white:esata";
gpios = <&qcom_pinmux 26 0>;
};
power {
label = "r7800:white:power";
gpios = <&qcom_pinmux 53 0>;
default-state = "on";
};
rfkill {
label = "r7800:white:rfkill";
gpios = <&qcom_pinmux 64 0>;
};
wifi {
label = "r7800:white:wifi";
gpios = <&qcom_pinmux 67 0>;
};
};
};
&adm_dma {
status = "ok";
};

View file

@ -0,0 +1 @@
#include "qcom-ipq8065.dtsi"

File diff suppressed because it is too large Load diff

View file

@ -185,6 +185,19 @@ define Device/R7500
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500
define Device/R7800
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8064-r7800
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := R7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade
BLOCKSIZE := 128KiB
PAGESIZE := 2048
BOARD_NAME := r7800
DEVICE_TITLE := Netgear Nighthawk X4S R7800
DEVICE_PACKAGES := ath10k-firmware-qca9984
endef
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7800
$(eval $(call BuildImage))

View file

@ -12,7 +12,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -506,7 +506,11 @@
@@ -506,7 +506,12 @@
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
qcom-ipq8064-ap148.dtb \
@ -21,6 +21,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
qcom-ipq8064-db149.dtb \
+ qcom-ipq8064-ea8500.dtb \
+ qcom-ipq8064-r7500.dtb \
+ qcom-ipq8064-r7800.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \
qcom-msm8974-sony-xperia-honami.dtb