Looks like the targets are Ubiquiti routers which don't come with any wireless cards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 42810
the driver did not handle all states correctly causing a deadlock of the i2c hw block.
Signed-off-by: Ing.Michele Mogioni <michele.mogioni@unimc.it>
SVN-Revision: 42807
This enables dedicated "rootfs" splitter by default. We still keep
CONFIG_MTD_SPLIT_SQUASHFS_ROOT, so the old (built-in) splitter will be
used as a fallback in case of problems.
Once we decide the dedicated partitioner works stable, we should remove
the old one completely.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42805
All TP-LINK machine names begin with "TP-LINK", so there's no need to check for
more specific model names. This also allows adding new models like the Archer
series more easily.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42795
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42782
Now that ucidef_set_interface_raw() has been updated to take a protocol
argument, use that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42666
This allows tagged and untagged traffic together on the same port on ar8327
switch devices.
I looked at the first attempt to do this in r40777 (ar71xx: Fix tagged+untagged
operation on AR8327N (#12181)). I also set the vlan and port egress policies
like that change. But I change vlan_tagged in an less intrusive way. The
tagged/untagged decision is now based on the following rules:
- if vid != pvid then traffic is always tagged
- if vid == pvid then vlan_tagged stores if the traffic should be tagged
Tested on TP-Link WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
SVN-Revision: 42653
This moves ingress, egress policy and pvid decisions to setup_port methods.
They arenow device type dependent.
This allows policy changes on only one device type which is needed to allow
tagged + untagged operation on ar8327.
Tested on TP-LINK WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
SVN-Revision: 42652
This makes TRX files more /compatible/ with firmware files (e.g. CHK).
This will allow us to put some TRX files in BIN_DIR if we need to.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42646
Without running fixtrx the image will not boot at the second time,
because the CRC the boot loader check is invalid at that time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42639
Upstream bcma patch:
bcma: use separated function to initialize bus on SoC
was backported incompletely. I missed arch code change.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42603
Kernel modules which are built using the SDK do not have access
to the .vermagic file in the Linux build dir, therefore the
generated .ipk metadata depends on kernel versions like
'3.10.49-1-unknown' which are not satisfiable by the kernel
meta package in the image.
Fix this problem by substituting 'unknown' with the current
version magic in include/kernel.mk when packing the SDK.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42590
fix inclusion of functions.sh in dsl_fs init script
without this, the following error is seen during build:
./etc/init.d/dsl_fs: line 4: /lib/functions.sh: No such file or directory
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
SVN-Revision: 42575
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
This device actually has a 8250 serial with a shift of 0.
Tested this on a BCM4708.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42538
We used separated patch for patches that were sent but not accepted yet.
It has changed now, so let's use the standard patch file for them.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42535
CONFIG_BLK_DEV does not activate any functionality, but many code, but
makes it possible to activate other options. Deactivating this breaks
the build of kmod-zram.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42528
This series of patches ports back some fixes of the ad799x driver, which were
commited between 3.10 and 3.15.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 42523
Convert gpiolib realization to platform driver and move to the
appropriate subdirectory. Misc GPIO interrupt acknowledgement placed
to the MISC IRQ handler since in fact we can detect only one GPIO state
change.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42512
Call generic_handle_irq() instead of do_IRQ() for chained interrupts,
remove XXX_NONE interrupts and call spurious_interrupt() when an interrupt
is unexpected.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42510
Rename config symbols to be consistent with other SoCs config symbols
supported by MIPS arch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42508
Tested with AR2315, AR2316 and AR2317 SoCs, not tested with AR2318 but
changes seems correct: revision is one more than AR2317.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42507
Convert the PCI controller support code to platform driver and move it to
appropriate subdirectory.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42506
It seems that the PCI controller does not support I/O ports, so remove
the ports range. Also correct the beginning of the memory range and its
size.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42503
Use __raw_{read,write}l accessors and use Abort interrupt to detect a
configuration space read/write errors. The second change improves errors
detection, what improves the device presence detection and helps us to
avoid following (and similar) errors:
pci 0000:00:00.2: ignoring class 0x7e0200 (doesn't match header type 02)
pci 0000:00:00.2: bridge configuration invalid ([bus 03-90]), reconfiguring
pci 0000:00:00.2: not setting up bridge for bus 0000:01
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42502
Add PCI IRQ controller to facilitate interrupt handling, move interrupts
initialization to the IRQ controller initialization from
pcibios_plat_dev_init() callback.
Also remove odd PCI dev configuration manipulation from pcibios_plat_dev_init()
callback.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42501
Explicitly configure PCI host controller, and do not expose it to PCI
subsystem. The PCI host controller acts as a usual PCI device connected
to the bus, but its configuration as a usual PCI device is senseless,
since the host controller provide access to _internal_ memory space for
_external_ device.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42500
- add comment, which briefly describes PCI controller features and
Fonera 2.0g schematics.
- rename several functions and structures, to make it clear that this
code only for AR2315 chips.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42499
Caller (generic PCI code) already do proper locking so no need to add
another one here.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42498
Remove options which already selected by ATHEROS_AR231X on which
ATHEROS_AR2315 depends.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42497
- remove odd flags and branching
- add __init mark
- make shorter variables names
- returns true or false from boolean functions
- unwrap short function declarations
- unwrap quoted string
- rename macroses with names in CamelCase
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42495
- use ether_foo() routines to work with addresses
- use ETH_ALEN inplace of magic '6'
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42494
Use mutex inplace of spinlock to make code simple, also call
mutex_{lock,unlock} explicitly to avoid sparse warning about context
imbalance.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42491
Remove FSF mailing address as suggested by checkpach and place license
URL.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 42487
