This fixes switch port mapping for: TL-WR841N/ND v8, TL-MR3420 v2 and
TL-WR941N/ND v5. All of them share the same Atheros ap123 reference
design.
The order of switch ports (shown in "swconfig dev eth1 show") is CPU,
LAN 4, LAN 1, LAN 2, LAN 3.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[included 2 more devices]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
these two devices have a Sata led for each sata port.
These leds must be controlled separately by a special
sata led trigger already used in oxnas target.
Both these devices have a single USB led, and to keep
consistent behaviour with the Sata leds that show
sata activity, this led uses usb-host trigger
to show usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Refer to LINUX_KARCH instead of ARCH when bundling DTS files in the image
builder tarball.
While we're at it, also dereference symbolic links when copying as some
kernel architectures contain symbolic links in their DTS directories.
This fixes aarch64 imagebuilders such as brcm2708/bcm2710 ones in particular
as the kernel refers to "aarch64" as "arm64" internally.
Ref: https://forum.lede-project.org/t/lede-image-builder-problem/3680
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Add device tree files for Solidrun ClearFog Base board.
We also need to backport some improvements for Armada
388 MicroSoM.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
The conventional model is now known as the "Clearfog Pro".
We keep the old armada-388-clearfog.dts file for compatibility reasons.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Add missing include of ramips.sh in order to import the missing
ramips_board_name() procedure.
Fixes FS#774.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Specification:
- SoC: MediaTek MT7620A (580 MHz)
- RAM: 64 MiB (Winbond W9751G6JB-25)
- Flash: 16 MiB (Spansion S25FL128SAIF00)
- LAN: x4 100M
- WAN: x1 100M
- Others: USB 2.0, reset button, wps button and 9 LEDs
Issues:
- 5 GHz band is not functional (missing driver support)
Installation:
Asus windows recovery tool:
- install the Asus firmware restoration utility
- unplug the router, hold the reset button while powering it on
- release when the power LED flashes slowly
- specify a static IP on your computer:
IP address: 192.168.1.75;
Subnet mask 255.255.255.0
- Start the Asus firmware restoration utility, specify the sysupgrade
image, and press upload
TFTP Recovery method:
- set computer to a static ip, 192.168.1.75
- connect computer to the LAN 1 port of the router
- hold the reset button while powering on the router for a few seconds
- send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
tftp> quit
Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
This device exactly same as NBG-419N but with USB port and USB Led.
Specification:
- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0
Installation via serial console (57600 8N1) from TFTP server
- rename the firmware to something shorter, for example
"sysupgrade.bin" (max. 32 chars)
- copy firmware TFTP server's directory
- when you power on device, and see U-Boot log, immediatly push "2"
once.
- You will see this message:
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?
- Push "y", and enter: device IP, then TFTP server's IP, and then
image firmware file name.
The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).
Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Build profile for Asmax AR 1004g refers to an invalid DTS "rg100a". The
correct DTS for this device is "ar1004g".
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
It has been shown that the Fritz boxes have the correct mac address set
in the wireless calibration data/eeeprom. Use this mac address as base
for the ethernet and xdsl interface increment/decrement the address to
match the values stored in the tffs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
commit 89878f60f4 x86: lift kernel minimum CPU requirement to Pentium MMX
caused kconfig havoc. Fix this and make sure PAE is enabled even on legacy
CPUs as the minimum required CPU has been Pentium MMX for a while now and
hence PAE is supported even on the x86_legacy target.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Anything older than that isn't supported since commit f4f8f4a180,
hence also switch to Pentium MMX when building the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
commit 4b4f739373 switched on HIGHMEM4G which implicitely disabled
PAE and hence also NX and other useful and security-relevant features.
Re-enable PAE by switching to HIGHMEM64G.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.
Hopefully fixes FS#758
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Module definitions for kmod-wdt-sunxi and kmod-eeprom-sunxi are removed
(wdt-sunxi was builtin anyways; nvmem-sunxi, which is the new name of
eeprom-sunxi is changed to builtin). As kmod-eeprom-sunxi was specified
in DEFAULT_PACKAGES, but not available on kernel 4.4, it was breaking the
image builder.
Support for kmod-sunxi-ir is added for kernel 4.4 (it is unclear why it
was disable before, it builds fine with with kernel 4.4).
Condtionals only relevant for pre-4.4 kernels are removed from modules.mk,
as sunxi does't support older kernels anymore.
Fixes FS#755.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It was originally only enabled for the "32" subtarget along with the
"usb" feature which is now also shared by the "64" target
This should fix the phase1 build of armvirt/64
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.
Ref: https://github.com/openwrt/luci/issues/1086
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
With update of ARC tools to arc-2016.09 based on GCC v6.x
we have to bump Linux kernel version so both toolchain and
the kernel use the same ARC ABIv4.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
With update of ARC tools to arc-2016.09 based on GCC v6.x
we have to bump Linux kernel version so both toolchain and
the kernel use the same ARC ABIv4.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.
In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.
On building all ends-up with:
---------------------->8------------------
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------
This was affecting Lede in case of CONFIG_ALL_KMODS=y.
The patch is already scheduled for v4.12 and once it is backported to
4.9.y it must be removed from here.
Note this patch makes sense not only for ARC instead it fixes
a generic issue which may affect more arches and platforms thus
putting it in "generic/" folder.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [patch rename]
Since commit:
7120438e5d
Seems that fsl_rstcr_restart() has been converted
to a reset handler and dropped as hook/callback.
Apply the same to the `tl_wdr4900_v1` target.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Re-applied patches:
001-powerpc-85xx-add-gpio-keys-to-of-match-table.patch
100-powerpc-85xx-tl-wdr4900-v1-support.patch
Dropped patch:
200-spi-fsl-espi-preallocate-local-buffer.patch
now part of kernel upstream hash
1423877b73
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Early SoC versions with an ECO of 1 required the gpio reset.
Mass production SoCs no longer need this work around.
Signed-off-by: John Crispin <john@phrozen.org>
Add the changes suggested by FS#716 to fix the switch driver initialization
on the ZTE Q7.
Also remove the `pinctrl-names` field obsoleted by the changes.
Reported-by: Harry Lau <harrylwc@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix a copy/paste error and include the ZBT-WE826 dtsi instead of the
ZBT-WG3526 one.
Fix the syntax error in the ZBT-WE826 dtsi to prevent an compile error.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The IMX6 PCIe host controller does not fire legacy interrupts if MSI is
enabled. A patch is being worked on to enable MSI at runtime only when
it is needed but meanwhile this patch will disable MSI for the imx6 kernel.
This fixes the no interrupt issue on cards/drivers that use legacy interrupts
such as ath9k.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Both of these boards share the same DTS, and hardware. The only
difference would be the PCI-E slot, and ath9k card found on the MX60W.
Due to the similarities, it would be more efficient to merge these
profiles.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This moves core router packages to the NAND target, to ensure they are
applied to all images. This change is being done due to an issue found
when flashing the MX60W image, which came without these when built as a
multi image.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The patch 523-MIPS-ath79-OTP-support only supports the OTP offsets for
AR933x chips, which has changed on newer platforms such as the AR934x.
The follwoing change is to add support for reading the OTP on the
AR934x. Tested on an Aerohive AP-121.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specification:
- SoC: MT7621AT, MT7603EN and MT7612EN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 512 MiB (EM6GE16EWXD-12H)
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Others: USB 2.0, micro SD slot, reset button and 8 x LEDs
Issues:
- Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs.
- The pwr LED is not GPIO controllable
How to install:
- The original firmware is OpenWrt, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.
Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
The wan port is connected to switch port 0. Fix the mediatek,portmap as
well as the default switch config.
Signed-off-by: Alexey Belyaev <spider@spider.vc>
Make switch port LEDs blink on activity as they do with stock firmware.
The u-boot loader sets suitable values in the LED control register that
unfortunately get blown away by the linux switch driver init. Restore
that value by using driver 'initvals'. 0x0431 is the led control
register, the value 0x0960. Each nybble represents each LED's mode
(LED3,2,1,0) in this case OFF, 1000LINK+Activity, 100/10LINK+Activity,
OFF. Only LED1&2 are physically present.
Enabling the blinkenlights exposed the fact that an RRCP packet was
being emitted by the switch on all ports every second. Further initvals
copied from stock firmware's u-boot driver disabled this 'feature'.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Allow per-device initvals in the DTS file for rlt8366rb
switches.
Shamelessly copies 30494598f8
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Migrate to new image generation and
introduce sdcard generation (based on sunxi).
Profile now generated via image/Makefile instead
of profiles/ directory.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
boardnames were changed with the recent target update. the sysupgrade board
detection was not updated properly.
Signed-off-by: John Crispin <john@phrozen.org>
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the Netgear R7500
dts file and backs off the previous attempt.
Now unloading and repeated module loading is working just fine.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading for Netgear R7500
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The patch follows the qualcomm code comments setting
SSUSB_CTRL_TEST_POWERDOWN to 0x1 and is testing and clearing the
bit during USB superspeed PHY init. According to Andy Gross it
needs to be BIT(26).
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes Ethernet<->WiFi bridge for Raspberry Pi and probably other devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Original armvirt target is now subtarget 32. Other than that the built
result should remain the same as before
Besides old features already available with arm64, the new armvirt/64
subtarget will also have those features originally enabled for
armvirt/32 with commit 44ecfc2 ("armvirt: new target")
- pl011, uart
- pl031, rtc
- pl061, gpio
- pci-host-generic
- virtio_{mmio,pci,net,blk,scsi,9p,console,balloon}
- smp with NR_CPUS=4
- cpu-hotplug
- ext4
- DEBUG_BUGVERBOSE for debug purposes
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Fix a '==' that should be a '=' in a test condition. Busybox fortunately
doesn't care.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add red:internet led on gpio 30 previously claimed as missing.
Wifi led was claimed as blue however there are no blue leds on the
board at all. Actually there are two wifi leds, green & amber so add
definitions for those. Make the newly discovered green wifi led gpio
14 the default.
There is no amber power led on this board. The mention of the amber
power led in the manual means power red and power green at the same
time.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[removed unnecessary aliases, add migration script]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
We need to keep the former used (unmodified) boardname in the metadata.
Otherwise an upgrade from an board using the old boardname will be
refused.
Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Mathias Kresin <dev@kresin.me>
PSG1218 got only 4 Ethernet ports and WAN on port 3 while
PSG1218K2C got 5 Ethernet ports and WAN on port 4
Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while
at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the stateless 4-byte op codes for this flash chip to fix reboot
hangs on SoCs expecting the flash chip in 3-byte mode.
Fixes: FS#179
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit 51397d7d95.
There are some unresolved random crashes on WRT1900AC v1 that still need
to be sorted out
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes:
Thermal sensors on bcm2835 SoC (BCM2835_THERMAL) [N/m/y/?] (NEW) aborted!
This symbol depends on ARCH_BCM2835 so it should be OK to disable it at
brcm2708 target only.
Fixes: 7d32caa61fb0 ("brcm2708: backport upstream sdhost controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Since 192f0a3db8 ("ath9k: unset the default LED pin if used by
platform leds") the default ath9k wireless LED is not set as soon as
any pin of the ath ath9k gpio controller is used.
All touched boards have leds defined which are using the gpio pins
exposed by the ath9k driver but rely on a default set wireless led
trigger.
Add the wireless leds were missing and setup the wireless phy trigger
in userspace.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Netgear R6220 requires the kmod-usb3 package and misses
kmod-usb-ledtrig-usbport package to setup the configured usb led
trigger.
Drop the already target selected kmod-mt76.
Fixes: FS#686
Fixes: 38bee61dab ("ramips: add support for Netgear R6220")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata.
Disable the 2.4GHz band as this band has no antennas attached but is
enabled in the eeprom/caldata.
Fixes: FS#691
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as
this board have a RT5592 and uses the rt2x00 driver. The mediathek
device tree bindings do not work here.
Fixes: FS#691
Fixes: d8dd207ea6 ("ramips: use the ralink,mtd-eeprom device tree property")
Signed-off-by: Mathias Kresin <dev@kresin.me>
The factory image has an uImage header covering the entire image and
not only the kernel. The original uImage header which covers only the
kernel is appended to the end of the image.
During LEDE boot the uImage rootfs splitter skips the whole filesystem,
can't find a valid filesystem magic and panics.
The last known working version was OpenWrt 14.07, which simply kept on
searching for an uImage header if the first found didn't resulted into
a working rootfs. This behaviour is kind of error prone since it could
produce false positives.
Since the sysupgrade image works fine in combination with the tftp
recovery for doing the initial installation of LEDE, simply drop the
factory image.
Related: FS#462
Signed-off-by: Mathias Kresin <dev@kresin.me>
The original implementation loaded the count register with (wrong) semi-
random values due to its implemenation nature.
If the wrongly calulated value was below the kickrate,
the WD was triggered and rebooted the system.
Rework this, partly based on upstream patches, to dynamically fetch the
current clockrate and calculate the proper offset for the WD countdown
register.
Before:
[ 143.800000] count val: 27219720
[ 148.820000] count val: 50623201
[ 153.830000] count val: 96425250
[ 158.830000] count val: 89735401
[ 163.840000] count val: 4756110
After:
[ 0.700000] MPCore WD init. clockrate: 299984500 prescaler: 256
countrate: 1171814 timeout: 60s
[ 358.530000] count val: 35154751
[ 363.540000] count val: 35154750
[ 368.540000] count val: 35154751
[ 373.550000] count val: 35154750
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
In preparation for bumping arm64 to 4.9, add a bunch of configuration
symbols that are available under arm64.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Drop sample command line to use against the ARM Foundation v8 model and
replace the path to something that matches LEDE's directory structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This required us to both download the Foundation emulator but also build
a boot wrapper. QEMU is now fully usable and is a much better
replacement.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Instead of renaming the default wireless led attached to the wireless
chip, add a new led using the platform leds with the phy0tpt trigger
set in userspace.
When switching ar71xx to device tree, the same can be done by using the
build in GPIO controller and without adding new bindings.
Drop the now unused platform code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With the fritz-tools a userspace parser for the Tiny Flash File System
is available and makes the tffs2 kernel patches obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.
Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.
Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix the list order instead of adjusting the controller scan order.
Revert the former required changes to the lantiq PCIe driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
* adds MT7530 DSA support
* backport latest ethernet driver
* add PMIC leds
* add auxadc support
* add efuse support
* add thermal sensor support
* add irq affinity support for ethernet
still todo
* DSA multi cpu support
Signed-off-by: John Crispin <john@phrozen.org>
Keeping it in base-files was resulting in adding it to the base-files
package. This file is meant to be included manually for initramfs
images only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There are currently several supported TP-Link devices without specified
version number in image name and/or DEVICE_TITLE (e.g. WBS210, WBS510,
TL-WR810N, TL-WA7510N, TL-WPA8630), but vendor website shows that there
are already more than one version of them on the market.
For devices like Archer C5, which second version is based on a total
different platform, missing version number in DEVICE_TITLE (used in
menuconfig) might be misleading for users.
To make it less confusing for users and easier to maintain in future,
include version number in image name and DEVICE_TITLE for all TP-Link
devices, even if there is only one version of device at the moment.
Also, keep DEVICE_TITLE in same format for all TP-Link devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Kernel/hardware support for this board has been implemented since
Chaos Calmer. This set of patches is to get the board identified in
userland. This will allow support for things like sysupgrade,
configuring initial LED state, configuring initial switch state, etc.
Signed-off-by: Ron Angeles <ronangeles@gmail.com>
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).
If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.
The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
On the more sophisticated (i.e. deeper FIFO) serial controllers,
flow-control might be needed to avoid dropping output.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G
Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer
Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000
Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize
Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
RGMII RX delay setting needs to be always specified for AR8337 to
avoid port 5 RX hang on high traffic / flood conditions.
Also, the HOL registers that set per-port and per-packet-priority
buffer sizes are updated with the reduced values suggested by the
QCA switch team.
Finally, AR8327 reserved register fixups are disabled for the AR8337.
This patch is adapted from the Code Aurora QSDK, but with magic
values mapped to proper defines.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the .dtsi
file. Most probably it went into openwrt here:
https://dev.openwrt.org/browser/trunk/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch?rev=45261
copied from Qualcomms attempt here: https://lkml.org/lkml/2015/11/20/116
Now unloading and repeated module loading is working just fine,
no matter if you'd remove dwc3-of-simple or dwc3.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Allow module unloading by fixing a mistake.
qcom_dwc3_phy_write_readback() is expecting (phy, offset, mask, value)
while the mistake was calling it with (phy, offset, value, mask)
The patch is swapping value and mask.
Without the patch unloading the dwc3 module was showing a
write to QSCRATCH failed and repeated module loading was
failing:
root@LEDE:/# rmmod dwc3
[ 19.167998] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.168084] usb usb4: USB disconnect, device number 1
[ 19.173371] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 19.177134] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.182960] usb usb3: USB disconnect, device number 1
[ 19.189023] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 19.192989] qcom-dwc3-usb-phy 110f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
[ 19.199064] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.205912] usb usb2: USB disconnect, device number 1
[ 19.211611] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 19.215905] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.221751] usb usb1: USB disconnect, device number 1
[ 19.227307] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 19.231795] qcom-dwc3-usb-phy 100f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
root@LEDE:/# modprobe dwc3
[ 29.583343] phy phy-100f8830.phy.4: phy init failed --> -110
[ 29.583399] dwc3 10000000.dwc3: failed to initialize core
[ 29.588169] dwc3: probe of 10000000.dwc3 failed with error -110
[ 29.652943] phy phy-110f8830.phy.2: phy init failed --> -110
[ 29.652988] dwc3 11000000.dwc3: failed to initialize core
[ 29.657735] dwc3: probe of 11000000.dwc3 failed with error -110
root@LEDE:/#
With patch repeated module unloading and loading is working good:
root@LEDE:/# rmmod dwc3
[ 22.622214] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.622298] usb usb4: USB disconnect, device number 1
[ 22.627401] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 22.631492] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.637054] usb usb3: USB disconnect, device number 1
[ 22.643721] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 22.647421] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.652910] usb usb2: USB disconnect, device number 1
[ 22.659219] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 22.662768] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.668604] usb usb1: USB disconnect, device number 1
[ 22.674803] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# modprobe dwc3
[ 25.404592] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.404694] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 25.409444] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.416589] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x10000000
[ 25.426509] hub 1-0:1.0: USB hub found
[ 25.431626] hub 1-0:1.0: 1 port detected
[ 25.435472] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.439206] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 25.444573] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.452926] hub 2-0:1.0: USB hub found
[ 25.460420] hub 2-0:1.0: 1 port detected
[ 25.525037] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.525099] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 25.529750] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.537002] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x11000000
[ 25.546583] hub 3-0:1.0: USB hub found
[ 25.551997] hub 3-0:1.0: 1 port detected
[ 25.555734] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.559621] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 25.564942] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.573063] hub 4-0:1.0: USB hub found
[ 25.580842] hub 4-0:1.0: 1 port detected
root@LEDE:/#
Fixes: dwc3 module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Many (most?) devices can't boot raw kernel using tftp and probably none
allows flashing it. It's way more usable to have TRX with kernel
containing initrams as such an image can be actually flashed.
An exception are Buffalo devices which have recovery mode with support
for booting kernels over TFTP. For them keep building default images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Makes use of the syscon tcsr and enables both USB ports. Cleans up
qcom-ipq8064.dtsi from previous attempts.
Fixes FS#497
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Current driver shows temp in full degrees while other apps await it
to be in millidegrees.
Initially the driver represents termal data in millidegrees but then
it gets divided by TSENS_FACTOR. So lets just set it to '1'.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Deactivate all the ARM64 erratums by default. The target code should
activate them if needed. This fixes a problem with a new erratum added
in kernel 4.9.17 breaking brcm2708.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This gets us in sync with dts from kernel 4.11. Two patches were already
backported earlier.
I decided to use 03x prefix as it's kind of similar to the 3xx prefix:
3xx - architecture specific patches
It isn't any documented or strict rule though. We don't need to stick to
it if we hit any problems.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
modify 0152-lantiq-VPE.patch from
commit e0229a16b0 ("lantiq: added support for VPE1")
- remove wdog function declarations from header (asm/vpe.h)
- remove wdog command line init functions (vpe.c)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
- remove patched header (vpe.h) because kernel
already provides one (asm/vpe.h)
- remove module softdog_vpe since watchdog functionality is unused
- remove module softdog_vpe from Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.
Fixes: FS#622
Signed-off-by: Mathias Kresin <dev@kresin.me>
