This adds the default LED and network settings for the PC Engines APU2
when running under the x86 target.
[dwmw2: Change Ethernet port setup]
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Based on a patch from Chris Blake <chrisrblake93@gmail.com>, except let's
do it by using the LED configuration instead of hard-coding it for each
board type. And try using /bin/board_detect to do the default behaviour,
on the first boot where the config hasn't yet been generated.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This change moves the files in 657418d to the root of the x86 target.
This is done in preperation for adding more devices under other
subtargets.
CC: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The DWR-512 embeds the hw slic device si3210. This device have the IRQ line
attached to the gpio1. This patch export the gpio1 with proper name and
parameters to the sysfs.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
this caused
'mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory'
when running sysupgrade -n
Signed-off-by: John Crispin <john@phrozen.org>
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.
Available FLASH space, with LEDE trunk, is only 240 KB.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.
Configure LAN as eth0 instead.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The list of v2/v3 devices is getting longer and makes reading the names of
the profiles unnecessary hard.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Fixes the following issue:
root@LEDE:/# sysupgrade /tmp/lede-mvebu-armada-388-clearfog-sdcard.img.gz
Saving metaconfig...
Image metadata not found
Use sysupgrade -F to override this check when downgrading or flashing to vendor firmware
Image check 'fwtool_check_image' failed.
root@LEDE:/#
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.
The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Upstream linux commit 7523e4dc5057e "module: use a structure to
encapsulate layout." moves some of the struct module members into a
separate struct module_layout.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Do not put the probe function into the __init section, but use the normal
section. This fixes a section mismatch warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were dropped because they are already applied
upstream:
0012-pinctrl-lantiq-fix-up-pinmux.patch
0013-MTD-lantiq-xway-fix-invalid-operator.patch
0014-MTD-lantiq-xway-the-latched-command-should-be-persis.patch
0015-MTD-lantiq-xway-remove-endless-loop.patch
0016-MTD-lantiq-xway-add-missing-write_buf-and-read_buf-t.patch
0017-MTD-xway-fix-nand-locking.patch
0044-pinctrl-lantiq-introduce-new-dedicated-devicetree-bi.patch
0045-pinctrl-lantiq-Fix-GPIO-Setup-of-GPIO-Port3.patch
0046-pinctrl-lantiq-2-pins-have-the-wrong-mux-list.patch
0047-irq-fixes.patch
0047-mtd-plat-nand-pass-of-node.patch
0060-usb-dwc2-Add-support-for-Lantiq-ARX-and-XRX-SoCs.patch
0120-MIPS-lantiq-add-support-for-device-tree-file-from-bo.patch
0121-MIPS-lantiq-make-it-possible-to-build-in-no-device-t.patch
122-MIPS-store-the-appended-dtb-address-in-a-variable.patch
The PHY driver was reduced to the code adding the LED configuration,
the rest is already upstream:
0023-NET-PHY-adds-driver-for-lantiq-PHY11G.patch
The SPI driver was replaced with the version pending for upstream
inclusion:
New driver:
0090-spi-add-transfer_status-callback.patch
0091-spi-lantiq-ssc-add-support-for-Lantiq-SSC-SPI-controller.patch
Old driver:
0100-spi-add-support-for-Lantiq-SPI-controller.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch add ZyXEL NSA325 2-Bay Media Server
The ZyXEL NSA325 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1600Mhz
- SDRAM memory: 512MB DDR2 400Mhz
- Gigabit ethernet: Marvell Alaska
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II ports (internal)
- 2 USB 2.0 ports (back)
- 1 USB 3.0 port (front)
- Fan (fixed speed)
- hardware watchdog in a mcu
Basically a bigger, more powerful version of NSA310,
installation is the same as they share the same flash layout.
A notable difference is that there is a hardware watchdog
in a mcu on the board, which is disabled by default in the LEDE u-boot.
The watchdog is also disabled with a GPIO activation through
raw register change when kwbooting or it would reset the board before
the new uboot was transferred.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
switch nsa310b mac address reading to mtd_get_mac_ascii helper as
it seems the fw_env.config file is created way later than when
network is set up, when I tested I still had that file included
in the image through /files folder.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
When we merged all the Geode boards into one generic target, the default
network and LED configuration was lost. Put it back.
Fixes: 9e0759ea26 ("x86: merge all geode based subtargets into one")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adds preliminary kernel 4.9 support for this target.
- Refreshed/Updated all patches
Added 3 new patches:
- 093 --> Add virtual PCI MMIO mapping
- 230 --> Remove deprecated code
- 240 --> Rework AT24 eeprom code to use the new NVMEM API
Compiled & tested on cns3xxx (gw2388)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add support for the Observa Telecom VH4032N router.
This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.
The wifi chip is an onboard Broadcom BCM43222.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove CONFIG_VLAN_8021Q overrides for two targets
These features are built into the kernel image for all targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Probe the switch through DT instead of a platform device. This fixes
probe, as GPIO offsets are now properly accounted for.
Fixes the following issue:
[ 0.802953] 8021q: 802.1Q VLAN Support v1.8
[ 0.810518] rtl8366_smi: gpio_request failed for 18, err=-517
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.
Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This patch adds support for the ADB P.DG AV4202N aka Pirelli PRG AV4202N.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for mapping some GPIO lines to IRQs. GPIO to IRQ mappings
were found out through experimentation, helped by having the GPIO as
output still toggling the IRQ input.
Based-on: http://patchwork.ozlabs.org/patch/660534/
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Setting the clear bit for an interrupt seems to cause interrupts to be
deasserted again immediately. So unset the bit for BCM6318 to allow
subsequent interrupts to still work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Default CONSOLE value for ar71xx target is "ttyS0,115200", so there
is no need to specify the same value in device profiles.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit reverts 42f3c1f ("arc770: fix broken upstream change")
and simultaneously adds back-ported fix from Linus' tree:
a524c218bc94 ("ARC: [arcompact] brown paper bag bug in unaligned
access delay slot fixup").
Note mentioned patch will appear in stable trees soon as well so
IMHO there's not much sense in adding this separate patch in lede/master branch.
As well as we will get rid of it here in 17.01 once we bump 4.4 kernel here
later down the line.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Jo-Philipp Wich <jo@mein.io>
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.
Signed-off-by: Claudio Leite <leitec@gmail.com>
buildbot fails to build without regmap, which I couldn't reproduce locally.
Hopefully this fixes it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
64 bit support for Raspberry Pi 3 is experimental. However, bcm2709 subtarget
should serve as a stable and compatible 32 bit support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds support for Raspberry Pi 3 on the bcm2709 subtarget, in order to
keep 32 bit image support when 64 bit support is added on bcm2710 subtarget.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Initial idea was to use package with this PHY driver for devices that
need it. Unfortunately this can't work as bgmac is built-in and PHY
probing happens before loading modules - it results in PHY subsystem
picking default (generic) PHY driver.
There were two ways of solving this:
1) Making bcm53xx use bgmac as module
xor
2) Built-in Broadcom PHY driver
After some quick discussion it seems we can simply built-in the driver
as increased kenel size is relatively small (1805 B).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
These are patches queued for 4.11. It adds support for even more hw and
removes some annoying WARN_ONCE.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's needed for macaddr_add.
Fixes: 50efd403e6 ("bcm53xx: set WAN MAC address to don't share one with LAN interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.
Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It just makes code consistent. This trivial change may be a 17.01
candidate to provide simpler backporting experience.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In kernel 4.9 it's already present so we don't want to overwite it (with
older & API incompatible version).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.
Runtime-tested on ar71xx, octeon, ramips and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.
Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.
The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).
If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.
Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.
Fixes: FS#451
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
After analyzing numerous NVRAMs and vendor firmwares it seems the base
MAC address is used for LAN interface. WAN interface has different one
which sometimes is set directly in NVRAM and sometines needs to be
calculated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Added the missing audio pcm interface in the .dtsi file for the rt5350
device. The update has been verified from the data get from the datasheet
and is very similar to the mt7620a.dtsi
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Use a vendor prefix as it has to be for all not core driver. Update the
compatible string in the device tree files accordingly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The comptible string is neither added by any LEDE patch nor exists in
in the kernel. Drop the sound node which was obviously added
accidentally with 9195d8da ("ramips: DTS rework").
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.
Remove the linux,modalias property. It is obsolete since kernel 4.4.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The setting mmc-ddr-1_8v in the platform dts leads to read errors. The
device is unusable and system reboots in a loop. Because NBG6817 is the
only mmc device, I removed it in base dts.
The second change removes settings now present in base dts.
The third change references was a wrong conversion of constants in the switch settings.
Switch now initializes again.
Signed-off-by: André Valentin <avalentin@marcant.net>
Refreshed patches for all supported targets.
Compile-tested on ar71xx, cns3xxx, imx6, mt7621, oxnas and x86/64.
Run-tested on ar71xx, cns3xxx, imx6 and mt7621.
Tested-by: Stijn Segers <francesco.borromini@inventati.org>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This activates the CONFIG_MIPS_APPENDED_RAW_DTB kernel configuration and
configures the F5D8235 V1 target to use append-dtb for kernel creation
instead of OWRTDTB.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This commit introduces CONFIG_MIPS_APPENDED_RAW_DTB as an alternative to
OWRTDTB. Both solutions can be used concurrently until all board
configurations have been changed.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In order to prepare support for generating tagged switch configurations by
default, explicitely request untagged configs for boards which do not already
request tagging to retain default behaviour.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Uses upstream code to parse DT supported band/frequency information.
Update existing .dts files to the new format and remove unnecessary
overrides.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We override default Ethernet interface with eth0 which often uses random
MAC due to missing proper NVRAM entry. Fix this by manually assigning
MAC in the config.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
All mvebu boards have three USB LEDs. The first one is used for the
USB1 port.
There are two LEDs related to the second USB port. The top (bar) LED
gets bright in case any USB device is connected to the second USB port.
If the connected device is an USB 3 (SuperSpeed) device, the small dot
LED bellow the "bar" LED gets also bright.
While at it, use a name for the USB LEDs that matches the names printed
on the case.
Fixes: FS#423, FS#425
Signed-off-by: Kabuli Chana <newtownbuild@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a pure rename without any changes. It makes maintaining bgmac
simpler and will hopefully make adding new kernel a bit easier.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Buffalo WCR-1166DS is a small wireless router with
- MT7628AN + MT7612E
- 64MiB DDR2 SDRAM
- 16MiB SPI flash
- 2T2R 11ac/a/b/g/n Wi-Fi
- 2x 10/100M ethernet switch
- 8x programmable LED
- 3x button
- UART pad on PCB (J2: 3.3V, GND, TX, RX)
factory image can be installed via stock web UI.
due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
only factory images for DHP-EU and DHP2-JP (fw ver. 2.x) are built.
this will not work for DHP-JP/AP/TW (fw ver. 1.x) because they use
different buffalo_csum() formula.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes logic bug(in function netdev_trig_notify) introduced in
0b2991a8ed commit.
Events triggered by different interfaces were stopping work queue so it
wasn't working for tx/rx mode.
Signed-off-by: Sergey Sergeev <adron@yapic.net>
Commit 29443e2 (mxs: remove modules.mk, select drivers in the kernel config)
missed to remove these references, so cleanup it now.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The VGV7510KW22BRN and VGV7519BRN do not have the same brnImage
signature. It was accidentally changed with ba42c1d ("lantiq: un-macro
the image building code").
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit e79ecb4c26.
The commit was incomplete and the issue that should be fixed isn't
that easy fixable. The Archer C7 mach file is used for the Archer C5,
WDR4900 and WDR7500 as well. Where the WDRs in compare to the Archer
do have blue LEDs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64.
.44 has been run-tested on the 17.01 branch here on ar71xx and mt7621.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
The following changes enables GPIO sysfs as well as the LEDS_GPIO option
within the kernel. This is required to enable LEDs over a GPIO
interface.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The GPL licensed source code of Belkin contains an ASIC based "Green
Feature". This change adds support for this Green Feature that can be
activated with an DTS option or swconfig.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
Before this change only port 4 of F5D8235 V1 worked at 1000Mpbs.
Comparing the current driver with the GPL_BELKIN_F5D8235-4_v1000
v1.01.24 sources showed that additional steps are required to set-up
the rlt8366s switch correctly.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
This change provides the possibility to define per-device initvals in
the DTS file for a rlt8366s switch.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which
should be included by default.
Signed-off-by: Yo Abe <abe.geel@gmail.com>
[Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
On some EX2700 devices, the MAC address from the eeprom data differs
from the actual MAC address. Fix that, and cleanup the DTS file
while we're at it.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
This commit adds 4 patches, one per kernel version that was used for
picking updates. This adds support for few new PHYs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB
TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")
Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This device has 2 TRX partitions (main one and failsafe one) and Linux
may not detect them properly failing to run userspace.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Even when the disk uses 4k blocks, the partition table still uses units
of 512 byte sectors. Always use ibs=512 for the offsets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ZyXEL NSA310 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: Realtek (over pcie)
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II port (1 internal and 1 external)
- 2 USB 2.0 ports (1 front and 1 back)
- Smart fan
The stock u-boot cannot read ubi so it should be replaced with the
LEDE/OpenWRT's u-boot or with a u-boot from here
https://github.com/mibodhi/u-boot-kirkwood
This device's boot ROM supports "kwboot" tool
(in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared)
that sends an uboot image to the board over serial connection, it is very easy to unbrick.
The stock bootloader can use usb and read from FAT filesystems,
so the installation process is simple, place the uboot file on a USB flashdrive
formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL
to the board and write the following commands in the bootloader console:
usb reset
fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin
nand write 0x1000000 0x00000 0x100000
reset
Now you are rebooting in the new u-boot, write this in its console to install the firmware:
usb reset
fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin
nand erase.part ubi
nand write 0x2000000 ubi 0x600000
If your firmware file is bigger than 6 MiBs you should write its size in hex
instead of 0x600000 above, or remove that number entirely (it will take a while in this case).
If you are using another uboot that can read ubi, set mtdparts like this
mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)
And set your bootcmd to be like this
bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000
Then you can install the firmware as described above.
After you installed (or configured) the u-boot for booting the firmware,
write the device's mac address in the ethaddr u-boot env.
The MAC address is usually on a sticker under the device (one of the two codes is the serial),
it should begin with "107BEF" as it is assigned to ZyXEL.
write in the u-boot console (use your MAC address instead of the example)
setenv ethaddr 10:7B:EF:00:00:00
saveenv
to save the mac address in the u-boot.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Instead of referencing u-boot packages from device profiles and having a
-all metapackage, make the u-boot packages hidden (they don't install to
bin/ anyway), and name the files in KERNEL_BUILD_DIR appropriately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to some reports, -march=pentium-mmx is a better choice for
older Geode CPUs than -march=geode anyway.
Bump the minimum architecture of the legacy target from i486 to
pentium-mmx. Anything older is not worth supporting anyway.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The le64 and be64 subtargets do not share a package architecture with
any other targets, so they are pretty wasteful for a development-only
target.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
While rt288x only has a MIPS 4KEc processor, it implements the MIPS32r2
architecture just like the 24Kc, so the instruction set should be 100%
compatible.
Switching it to 24kc allows it to share the package architecture with a
lot of other targets instead of creating a special case, saving
buildbot resources.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support Abicom International Scorpion SC450 Board
QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Support Abicom International Scorpion SC300M Module
QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Changes the platform to use the Chipidea driver instead of the
generic USB host driver which has support for both host and
device modes (selected on boot).
The changes in 930-chipidea-pullup.patch are already in mainline.
I'll upstream 920-usb-chipidea-AR933x-platform-support.patch once I
can test the changes with a newer kernel.
Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
erlite mtdparts exposes boot0, boot1 and eeprom regions
as read/write.
this patch adds readonly flags, so these regions can't be
modified. same as it is already for ER profile.
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.
This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since the MIPS IRQ stack patches, lantiq devices were emitting a storm
of messages like this:
[ 567.872172] Spurious IRQ: CAUSE=0x1100c300
Fix this by reworking the IRQ dispatch code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The soft_config partition must be writeable for rbcfg to be able to
enact changes to the routerboot configuration.
The read-only flag was a mistake in the initial patch. Removing it
brings mach-rb941.c in line with all other RB platforms.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.
This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.
Signed-off-by: Zhang Jingye <934526987@qq.com>
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
This change adds the sp5100_tco driver as a kernel module for the x86
target. Specifically, this can be used by the PCEngines APU2/APU3. The
reason for having this as a kernel module is to allow users to
load/unload it on demand, as the I2C interface on the APU2/APU3 will not
work while this module is loaded. More info can be found on GitHub at
https://github.com/riptidewave93/LEDE-APU2/pull/5#issuecomment-255667736
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This adds the following patches to the x86 target:
sp5100_tco: Add AMD Mullins platform support
sp5100_tco: Add AMD Carrizo platform support
sp5100_tco: fix the device check for SB800 and later chipsets
watchdog: sp5100_tco: properly check for new register layouts
With these added, the sp5100_tco driver can then be used on newer AMD
platforms, such as the PCEngines APU2/APU3 boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Add full support for Mikrotik RB-941-2nD (hAP lite)
Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.
There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Running ar8327_get_arl_entry() early after boot leads to MDIO related system
lockups on several devices using this driver.
Since dumping the ARL table contens is an optional, uncritical feature, simply
disable the code for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes hangs in igb that happen if the update call interrupts an
already existing dev_get_stats call. In that case the calling CPU
deadlocks because it's trying to acquire the same spinlock recursively.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This specifies wireless limitations for Netgear R8000 making sure people
won't use channels incorrectly (limited performance). There are also 2
new DTS files not used by us yet.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
At the moment we have 2 seperate device tree sources: 1 for ipq8064 soc located
in kernel source and 1 custom in LEDE for ipq8065.
ipq8064 and ipq8065 SoCs are completely identical except ipq8065 has higher cpu
frequencies and adjusted corresponding power supply.
This commit makes ipq8065 DTS to contain only specific for ipq8065 DT entries while
pulling all the basic SoC stuff from ipq8064 DTS.
It makes easier to manage ipq806x device trees and instead of committing changes into
2 seperate equal DTS we are ending up with only 1.
It also enables ipq8065 devices to automatically receive changes made in upstream kernel.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
According to Qualcomm SDK usb3 phy suspend should be disabled for
ipq806x.
This may solve issue on some ipq806x devices that breaks usb3
storage peripherals during system boot.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)
Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
- RAM: 64MB DDR
- Storage: 16MB NOR SPI flash onboard
- Omega2+
- RAM: 128MB DDR
- Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
- All Docks Provide:
- Micro-USB port to provide power to the Omega
- On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
- USB 2.0 socket connected to Omega
- Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
- Omega GPIO breakout
- Allows for connection of Omega Expansions:
- Ethernet Expansion
- Relay Expansion
- PWM Expansion
- OLED Expansion
- Ethernet Expansion
- Proto Expansion
- Cellular Expansion
Signed-off-by: Lazar Demin <lazar@onion.io>
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify switch configuration on Linksys WRTxx00AC series.
LAN = eth0, WAN = eth1
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[Álvaro]: also change WAN LEDs
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This reduces the amount of hacks in the makefile code.
Remove the apm821xx code to do the same - it was broken and left both
compressed and uncompressed images in $(BIN_DIR)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It could cause crashes with some forms of virtualization, and it is
unlikely to work properly with most systems.
It's safer to just disable it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There's a GPIO that can switch between power to USB pins for the
internal MiniPCIe slot or the external USB port.
People are more likely to use the external one so enable it by default.
Existing configurations should be unaffected
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Is it used by VMware Fusion by default. This allows images to boot
without further config changes in VMware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Partition label "linux" prevents the root file system to be mounted at
boot time leading to a kernel panic. After changing it to "firmware",
the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data"
are correctly recognized.
The attached IP175C 10/100 MBit switch cannot connect to a link with
fixed 1000Mbit speed. The correct link speed is 100MBit. The switch
is detected and can be configured via mdio bus and should allow two
separable VLANs to be configured for the 4 available ports.
Signed-off-by: Yo Abe <abe.geel@gmail.com>
[picked from openwrt/PR#330]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.
Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
- USB 2.0 socket
- MicroSD socket
- 100Mbps Ethernet x1
- 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
DAC/ADC (support WIP)
- Micro USB for power and console (UART2)
Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
original firmware uses Ralink SDK Wi-Fi drivers and not
mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
Ethernet or the micro USB console to configure Wi-Fi again
Signed-off-by: Andrew Yong <me@ndoo.sg>
This patch adds support for serial console on Mikrotik RB411 and RB433
series devices.
Signed-off-by: David Varga <duvi@duvinet.hu>
[picked from FS#377]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The hardware queue scheduling is apparently configured with fixed
priorities, which creates a nasty fairness issue where traffic from one
CPU can starve traffic from all other CPUs.
Work around this issue by forcing all tx packets to go through one CPU,
until this issue is fixed properly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit af79fdbe4a changed the code to use tx_nbits for dual SPI tx
transfers, however the SPI stack only allows this when the device mode
includes the relevant bit as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This code was marked as incompatible to Linux 4.4 well over a year ago
and nobody cared, and now it's breaking builds.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This target has consistently failed builds for a long time and it does
not look like it has any users left, nor any maintainers.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Without this patch swconfig will only allow setting up a total of 16
VLANs, with VLAN ID range of 0-15.
Tested on ubnt-erx.
Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
Fixing pvs1 bin voltage as found in GPL tarball and Qualcomm SDK.
Also adjusting smb208_s2a/b minimum voltage to reflect lowest value in pvs table.
Current ipq8065 devices in LEDE choose (based on eFuse data) pvs bin n4, that has
correct values in DT, but in future a new device may choose n1 or n6.
Without this change n1 is semi-correct and n6 is not available, because OPP driver
disregards bins with voltage values that regulator cannot supply.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This adds USB initialization fixes for Danube, Amazon SE and xrx300 and
should fix the clock on at least Danube which hopefully closes FS#351.
The xrx200 usb driver now uses more memory for the dwc2 fifos, this was
increased in the chip compared to ar9.
This is based in part on the vendor documentation and the vendor code
base as a reference.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DMA controller used only local locks, which will not lock the
section against other CPUs, fix this by using spin locks.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we generate images with metadata attached, require it in order
to prevent accidentally flashing the wrong image to a board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for the integrated AC97 sound device on motherboards
with AMD CS5535/CS5536 chipsets.
Tested on Wyse Winterm S30.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
The boot loader of many boards provides a kernel boot argument with a
broken console parameter to the kernel. This will be taken before the
stdout-path defined in device tree and the serial will not work on this
board. Multiple boards are affected by this problem, so revert this
patch for all boards. Later we can remove the boot arguments from the
device tree again, after the individual board was checked to work.
This partly reverts this commit:
commit 4995c64857
Author: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Date: Sun Dec 11 21:55:00 2016 +0100
lantiq: specify console using stdout-path instead of cmdline argument
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To achieve this, device tree compatible string was used as boardname and
the value of it will be checked against supported_devices list.
It should be noted that we do not distinguish between
sun5i-a13-olimex-som and sun5i-a13-olinuxino as they share the same dts
file.
The other thing is that we need to gunzip the generated firmware to do
fwtool check.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Enalbe builtin support for FAT filesystem as we need to mount boot
partition to store sysupgrade.tgz there
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Two things that need to be noted
- There is no partition type id allocated for squashfs yet. In the
case of sunxi, any non-zero value should work and we keep it 83 (the
value for ext4)
- Remaining spare space within the rootfs partition, not the entire
sdcard space will be formated as either f2fs or ext4 and mounted as
overlay to serve the role of rootfs_data.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The new Device/xxx were transformed automatically from old profiles.
Most device names are now taken from basename of the corresponding
kernel device tree file. Device/sun5i-a13-olimex-som is an exception
because it is not explicitly supported in the kernel yet and shares the
same dts file with Device/sun5i-a13-olinuxino
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
To squash error messages at boot time
mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The kernel will detect if the host supports this, so we can just enable
it in the kernel config.
Tested on an APU2 with AES-NI support and a KVM VM on a Xeon E5520 host
without AES-NI support.
Throughput over an IPsec tunnel between these 2 hosts increased from
~63Mbps to ~140Mbps. Ciphers: AES_GCM_16_256/PRF_HMAC_SHA2_512/ECP_521.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
WL500GPv1 profile included ath5k which made it usable only for people
who decided to replace default BCM4318 card with Atheros one. We can't
have profile for every possible configuration. If someone adjusts hw in
such a way he can always install a proper package.
WRTSL54GS profile got extra packages for a specific USB usage. Our
standard profile provides basic USB and we should stick to this. We
can't make everyone happy by including packages for all common USB use
cases and all common filesystems.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The powerpc boot wrapper Makefile is not parallel build safe, causing fixdep
to fail reading dependency files of the addnote, hack-coff and mktree
utilities when concurrently building different image targets.
A typical failure looks like:
Building modules, stage 2.
HOSTCC arch/powerpc/boot/addnote
HOSTCC arch/powerpc/boot/hack-coff
DTC arch/powerpc/boot/taishan.dtb
HOSTCC arch/powerpc/boot/addnote
HOSTCC arch/powerpc/boot/hack-coff
MODPOST 800 modules
fixdep: error opening depfile: arch/powerpc/boot/.hack-coff.d: No such file or directory
scripts/Makefile.host:91: recipe for target 'arch/powerpc/boot/hack-coff' failed
make[5]: *** [arch/powerpc/boot/hack-coff] Error 2
make[5]: *** Waiting for unfinished jobs....
fixdep: error opening depfile: arch/powerpc/boot/.addnote.d: No such file or directory
scripts/Makefile.host:91: recipe for target 'arch/powerpc/boot/addnote' failed
make[5]: *** [arch/powerpc/boot/addnote] Error 2
rm arch/powerpc/boot/taishan.dtb
arch/powerpc/Makefile:263: recipe for target 'cuImage.taishan' failed
make[4]: *** [cuImage.taishan] Error 2
make[4]: *** Waiting for unfinished jobs....
Add a GNU make specific .NOTPARALLEL pseudo rule to enforce sequential building
of the addnote, hack-coff and mktree executables.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This allows more feature complete images. Of course it affect the size,
e.g. enabling b43 bumped rootfs from 1569618 to 2029122 for me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This chip has write protection enabled on power-up, so this flag is
necessary to support write operations.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
This flag was added to 4.9 with upstream commit
76a4707de5e18dc32d9cb4e990686140c5664a15.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
[refresh and adjust platform patches, fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
LS1088A is an ARMv8 implementation combining eight ARM A53 processor
cores. The LS1088ARDB is an evaluatoin platform that supports the
LS1088A family SoCs.
Features summary:
- Eight 64-bit ARM v8 Cortex-A53 CPUs
- Data path acceleration architecture 2.0 (DPAA2)
- Ethernet interfaces
- QUADSPI flash, 3 PCIe, 2 USB, 1 SD, 2 DUARTs etc
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
In case the soft reset in dwc2_core_reset() timeouts, the
hsotg->core_params are freed albeit it is owned by the core. This
results into a kernel panic as shown in FS#351.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the the dt-bindings macros and add the reset button.
Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.
Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit introduced a syntax error in ox820-akitio.dts which is
fixed now:
commit 5cde94d9ab
Author: Daniel Golle <daniel@makrotopia.org>
Date: Sat Sep 24 01:14:53 2016 +0200
oxnas: backport upstream NAND driver
This caused the folowing error message in the build bot:
Error: arch/arm/boot/dts/ox820-akitio.dts:146.3-147.1 syntax error
FATAL ERROR: Unable to parse input tree
scripts/Makefile.lib:293: recipe for target 'arch/arm/boot/dts/ox820-akitio.dtb' failed
make[5]: *** [arch/arm/boot/dts/ox820-akitio.dtb] Error 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have profile for this device thanks to DEVICE_PACKAGES now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Russell Senior <russell@personaltelco.net>
We don't use this driver since commit 741715331a ("bcm53xx: switch to
m25p80 and drop bcm53xxspiflash").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There was a typo in Makefile that prevented using these profiles.
Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
depending packages have been moved to kernel-config
- kmod-xen-kbddev in 9fde361
- kmod-xen-fs, kmod-xen-evtchn, kmod-xen-netdev in 018807d
this will also fix imagebuilder
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
crypto4xx_probe() is in the __init section and referenced by code form
other sections, which causes a build error. Backport a patch from
mainline kernel to fix this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following commit changed the build templates name but forgot to
update the TARGET_DEVICES variable properly.
commit f9226158be (lantiq: rename EASY98000 to EASY98000NOR)
Signed-off-by: John Crispin <john@phrozen.org>
The generic lzma-loader uses vmlinux.lzma as an input to compress so we
need to provide a lzma compressed version of the initramfs kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The power LED can not be used for indicating the xDSL line state and
the in system (boot) state at the same time in LEDE. As soon as the
xDSL Line goes down, the power LED is switched off.
During xDSL handshake the power led would blink with the same or a
similar pattern as during boot.
Both might confuse users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to a hardware bug of Atheros 8030 phys, the driver need to reset
the phys on link state change.
Use the correct compatible string for the at903x phys connected to
switch port 0 and 1.
Fix the pinmux of the gpio lines connected to the reset pin of the phys
and define the reset-pins to let the driver do the fixups.
Fixes FS#343
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.
Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.
Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.
To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove dt: it is implicitly enabled based on the kernel config
Remove tar.gz and jffs2_nand: Legacy build code has been removed,
NAND devices are only supported with UBI now.
Remove ubifs: deprecated, use squashfs images instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The priv->vlan_id member is of size AR8X16_MAX_VLANS, not AR8X16_MAX_PORTS,
so check for the proper maximum value in order to avoid capping valid VLAN IDs
to 7 (AR8X16_MAX_PORTS - 1).
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Enabled Hyper-V network interface card driver, display adapter driver,
storage driver, keyboard driver, mouse driver and Hyper-V utility and
EFI boot support in the kernel for subtarget x86/64.
Convert the img file to vhd by Ubuntu qemu-img, rather than by the buildroot's
built-in qemu-img.
Tested on Windows Server 2008 r2 and 2012 r2 Gen1 and Gen2 VMs.
Signed-off-by: Tedaz <tedaz99999@hotmail.com>
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.
The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)
The result factory image is flashable from the stock web ui.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
mktplinkfw ignores -j in combined mode, the EOF marker is added by
tplink-safeloader.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In the latest version of grub-mkimage, the prefix option is mandatory.
Not supplying it fails with:
```
Prefix not specified (use the -p option).
```
In grub-2.02-beta2 a DEFAULT_DIRECTORY was defined
in `include/grub/osdep/hostfile_unix.h` as:
```
#if defined (__NetBSD__)
/* NetBSD uses /boot for its boot block. */
# define DEFAULT_DIRECTORY "/"GRUB_DIR_NAME
#else
# define DEFAULT_DIRECTORY "/"GRUB_BOOT_DIR_NAME"/"GRUB_DIR_NAME
#endif
```
Where:
* GRUB_BOOT_DIR_NAME == boot
* GRUB_DIR_NAME == grub
This was used if the -p option was omitted.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This patch is part of a series adding support for 0x9200 and 0x9300. The
prior was merged into the upstream kernel while the latter was not due
to lack of testers. Drop the patch as it is untested and most likely
unused.
Signed-off-by: John Crispin <john@phrozen.org>
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
The si3210 is a SLIC device providing a complete analog telephone
interface and therefore frequently used in soho router.
The si3210 have a native spi interface to be controlled by the CPU
but currently there is no dedicated driver in lede.
Adding a registration for this device in spidev allow to control the
device in user space.
This way of patching is also in line with the rationale of the spidev
driver, see: http://marc.info/?t=148145791900001&r=1&w=2
The si3210 has been also added in the DWR-512 DT to properly describe
the HW.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
While researching for the armvirt target, I looked at the
existing arm platforms. It turns out that the mediatek target
with its sole MT7623N/A chip is sold as a "highly integrated
multimedia network router system-on-chip". To that end, it
lists support for the "NEON multimedia processing engine with
SIMDv2 / VFPv4 ISA support".
<http://topics.mediatek.com/en/products/connectivity/wifi/home-network/wifi-ap/mt7623na/>
So this patch enables the CPU_SUBTYPE to use this information.
This should have the nice side effect that LEDE's phase2 builders
no longer need to built a separate "cortex-a7" target, so this
should free up some resources.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Bump & refresh patches for all 4.4 targets.
Compile & run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the mtd partition layout and enable both radios in the dts
Tested-by Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
The TL-WR842N v2 has the following switch port layout with swconfig port 0
being connected to eth1:
Power LAN4 LAN3 LAN2 LAN1 WAN USB
(*) | [...] | [...] | [...] | [...] | [...] | [.]
swconfig port: 1 4 3 2 n/a
netdev: eth1 eth1 eth1 eth1 eth0
Adjust the board defaults to match this model specific layout.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The imagetag RSA signature field may not exceed 20 characters, so trim the
Git hash portion from the REVISION variable in order to ensure that the
resulting string fits within this field.
The current revision values may be longer than 20 chars, especially when
building within a dirty tree. In this case, the revision will look like
"r2435+75-b4aa3c8" which, combined with the "LEDE-" prefix, is 21 chars long.
Fixes the following error spotted by the buildbots:
Error: RSA Signature (rsa_signature,r) too long.
make[4]: *** [.../lede-brcm63xx-generic-NEUFBOX6-squashfs-cfe.bin] Error 1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch add the 3G modem DWM-158 to the usb-serial option driver.
The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem
supportet by lede. The patch has been submitted and merged in the upstream
linux-next repository.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
This patch adds supports for the WNR2000v1 board with 4MB flash, and
produces device-specific factory, rootfs, and sysupgrade files for the
WNR2000v1. This board is errorneously claimed as supported on the OpenWRT
wiki as AP81, but AP81 image would not work because of APT81 image
requiring having 8MB of flash, while WNR2000v1 has only 4MB.
The image requires the u-boot bootloader to be modified to fuhry's
bootloader first.
Short specification:
- CPU: Atheros AR9132
- 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps
- 4 MB of Flash
- 32 MB of RAM
- UART header (J1) on board
- 1x button
Factory/Initial flash instructions:
- Set up a TFTP server on your local machine.
- Download the uImage for ar71xx-generic and the rootfs image for
ar71xx-generic-wnr2000 and save in the tftp server root.
- Gain serial access to the router via the UART port (telnetenable over
the network only won't work!).
- Upgrade the u-boot bootloader to fuhry's version by running the
script: http://fuhry.com/b/wnr2000/install-repart.sh
- When the router restarts, interrupt u-boot and gain access to u-boot command line.
- Repartititon the board and flash initial uImage and rootfs as follow.
Commands to type in u-boot:
# tells u-boot that we have a tftp server on 192.168.1.10
setenv serverip 192.168.1.10
# tells u-boot that the router should take the address 192.168.1.1
setenv ipaddr 192.168.1.1
# erase the region from 0x050000-0x3f0000
erase 0xbf050000 +0x3A0000
# loads sqfs.bin on TFTP server, and put it to memory address 0x81000000
tftpboot 0x81000000 sqfs.bin
# it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ
# copy bit by bit 0xZZZZZZ bytes from offset 0x050000
cp.b 0x81000000 0xbf050000 0xZZZZZZ
# same to the uImage.bin, write it right next to sqfs.bin
# again, 0xYYYYYY is the length that tftpboot reports
tftpboot 0x81000000 uImage.bin
cp.b 0x81000000 0xbf2a0000 0xYYYYYY
# We need to tell the kernel what board it is booting into, and where to find the partitions
setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd"
# Tell u-boot where to find the uImage
setenv bootcmd "bootm 0xbf2a0000"
# Tell u-boot to save parameters to the u-boot-env partitions
saveenv
# Reset the board
reset
Tested on:
- WNR2000v1 board.
- Initial flash works.
Known bugs:
- I don't know why factory image doesn't work on initial flash on stock
firmware in u-boot recovery mode while it should.
- Sysupgrade does not yet work, if you do -f it will mess up your
installation (requiring a reinstall of sqfs and uImage).
Signed-off-by: Huan Truong <htruong@tnhh.net>
The xt_id match was used by the firewall3 package to track its own rules but
the approach has been changed to use xt_comment instead now, so we can drop
this nonstandard extension.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
These patches were queued for 4.10. For possible use cases see added:
[PATCH] ubifs: Use dirty_writeback_interval value for wbuf timer
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This also makes the detection more flexible, as it doesn't need to check
for each model explicitly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are many targets using user space scripts to generate firmware but
bcm53xx doesn't need this, so let's disable that kernel option.
This lets us avoid some scary-looking kernel warnings like:
brcmfmac 0001:04:00.0: Falling back to user helper
firmware brcm!brcmfmac43602-pcie.txt: firmware_loading_store: map pages failed
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
/etc/preinit has been the default init-script for a very long time (at
least since Linux 2.6.30 in OpenWrt). Remove the kernel command line
"init" parameter to get rid of duplicate and inconsistent definitions
of this parameter (some boards, like FRITZ3370 for example did not use
it at all, while it's just copy and paste on others).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use devicetree's /chosen/stdout-path instead of the kernel command line
(embedded in the .dts-files) to specify the serial console. Using the
chosen node is recommended on devicetree based platforms.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.
YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.
Common specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm
SR3200 specification:
- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB
XD3200 specification:
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB
LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.
Flash instruction under vendor firmware, using telnet/SSH:
1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
This attribute is not evaluated any more and the boot loader on these
reference boards does not provide a broken root= or console= parameter.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add an extra function to patch the mac and fixup the checksum
afterwards. Calculate the checksum position automatically. The offset
to the mac address is the same for all checksum protected EEPROMs.
No EEPROM requires a byte swapped mac address. The mac byte swap code
was required due to an bug in the script that is now fixed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).
The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)
Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Rob suggested I should use of_machine_is_compatible insteak of a new
property and updated patch has been sent.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is helpful for Orion-based NAS boxes that have the XOR engine enabled
since it provides faster software RAID.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The harddisk target is for NAS boxes, so set the DEVICE_TYPE accordingly so we
get a sensible default package selection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable support for this machine in the kernel and also produce valid image
files with the correct machine id.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW,
because ar71xx is not converted to device tree yet.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.
REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.
Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.
Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
sysupgrade command fails due to missing U-Boot environment-processing
binaries on sysupgrade ramdisk. The missing binaries result in the
following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
The name from the Device define will be used in the metadata. Due to
typo/different spelling, this name might not match the one exported in
/lib/mvebu.sh.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr
Signed-off-by: Andrew Yong <me@ndoo.sg>
Imported from https://source.codeaurora.org/quic/qsdk/system/openwrt/commit/?h=korg/linux-3.4.y/release/arugula_bb_cs&id=2be4f8a8b205ae1a37db44839864451ebe893e6e
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Enable flow control of LAN and WAN ports to
get better performance.
Setup pvid as 0 for all ports during initialisation
to avoid confusion during system or switch INIT.
Disable PORT MAC before config MAC to avoid it work abnormal.
This change is for IR-054144, IR-057315.
Change-Id: I345f3dffa59ad3f97150e09692723da12a7b1067
Signed-off-by: Zou Shunxiang <shunxian@codeaurora.org>
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Imported from e1aaf7ec00%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: net: ar8216: address security vulnerabilities in swconfig & ar8216
This patch does the following changes:
*address the security vulnerabilities in both swconfig framework and in
ar8216 driver (many bound check additions, and turned swconfig structure
signed element into unsigned when applicable)
*address a couple of whitespaces and indendation issues
BUG=chrome-os-partner:33096
TEST=none
Change-Id: I94ea78fcce8c1932cc584d1508c6e3b5dfb93ce9
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/236490
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Commit-Queue: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from fd7b89dd46%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: prevent device duplication in ar8xxx_dev_list
If probe is called twice, once for PHY0 and a second time for PHY4,
the same switch device will be added twice to ar8xxx_dev_list, while
supposedly this list should have one element per hardware switch present
in the system.
While no negative impact have been observed, it does happen if a
platform instanciates these two PHYs from device-tree, as an example.
Change-Id: Iddcbdf7d4adacb0af01975b73f8e56b4582e894e
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/234790
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from c3fd96a7b8%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: hold ar8xxx_dev_list_lock during use_count--
It is possible for the remove() callback to run twice in parallel, which
could result into --use_count returning only 1 in both cases and the
rest of the unregistration path to never be reached.
This case has never been observed in practice, but we will fix
preventively to make the code more robust.
BUG=chrome-os-partner:33096
TEST=none
Change-Id: If09abe27fdb2037f514f8674418bafaab3cbdef6
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/232870
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from c05af20272
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: sync mib_work cancellation
ar8xxx_mib_stop() is called from ar8xxx_phy_remove(), so we want to make
sure the work doesn't run after priv is freed / the device ceases to
exist.
BUG=chrome-os-partner:33096
TEST=none
Change-Id: Iafb44ce93a87433adc4576e5fea5fda58d1f43a9
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/232827
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
RPM clock controller driver had made its way upstream and previous
approach of directly redoing a driver to support ipq806x is a no go anymore.
Thus reverting mentioned patches to upstream state and renaming
in correct patch numbering accordance.
To make the driver work on ipq806x boards we introduce a custom patch.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
