The active_low flag was missing for the user LED. This LED is open drain
(confirmed in OEM source) and open drain only makes sense for active low
GPIOs.
The two wireless LEDs mentioned in the comments are also #defined for
future reference.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.
Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.
This patch fixes these issues and renames the corresponding #defines for
clarity
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The gpios that control power toggle for USB on the RouterBOARD devices
are active low _off_ switches.
When they are active (low), power is off. When they are inactive
(high), power is on.
Rename GPIO defines, set gpios to GPIOF_ACTIVE_LOW for consistency and
reflect their true action in the display name. This brings openwrt code
in line with OEM.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
convert the usb and both sata port power related gpio-hogs to
what they really are: fixed-regulators.
The ethernet phy-reset gpio-hog is replaced by a proper
upstream (4.15+) reset-gpios property in the mdio-node.
So this will work eventually.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
The MBL's rootfs.img.gz image is generated in much the same way.
Hence this patch preemptively splits the rootfs.img.gz image into
a sysupgrade and a factory image.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for squashfs as the root filesystem.
advantages:
- migrate from a existing -ext4 installation and back
with the sysupgrade utility
- existing partition layout will not be lost during switch
- slightly smaller image size as compared to the -ext4 image.
disadvantages:
- needs f2fs + tools. This is because fstools rootdisk.c decides based
on the partition size (currently root partitions > 100 MiB) f2fs is
used as the rootfs_data filesystem.
- rootfs_data is placed into the rootfs partition after the squashfs.
This makes it difficult for tools that expect a /dev/sda${X} device.
It also makes it difficult for data recovery tools as they might not
expect to find a embedded partition or will be slightly confused.
... or will not support f2fs.
For people with existing build configurations: make sure to include mkf2fs
and f2fsck packages into the image. Otherwise the new -squashfs image will
only boot from the ram-overlay.
Note:
All overlay data (configurations/all installed packages/...) will be
placed in inside the rootfs partition (i.e. /dev/sda2) just after the
squashfs image.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It was present as 4.4 compatibility, but since we now use 4.9 or later
with the new upstream solution, we don't need it anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This includes Linksys EA9500 support, BCM53573 timer fix and
upstream-ready partitions patch that replaces two downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
USB 3.0 PHY is attached to the MDIO bus and should be supported
(accessed) as a MDIO device. This wasn't known initially which resulted
in writing driver that was working with MDIO bus (using some magic
values) without knowing it.
This commit updates DT to properly describe MDIO & USB 3.0 PHY and
enables required kernel drivers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is a new & warm feature that allows nesting partiitons in DT and
mixing their types (e.g. static vs. dynamic). It's very useful for
boards that have most partitions static but some of them require extra
parsing (e.g. a "firmware" partition).
It's required to successfully backport support for new devices using
that new syntax in their DT files.
Since brcm63xx has a custom alternative patch the upstream one is being
reverted for it. The plan is to make brcm63xx use the upstream
implementation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The OCEDO Raccoon only has one ethernet port, but currently uci sections
for WAN and LAN are created.
Additionally, newer versions of the devices U-Boot (units with SteelWRT)
set the kernel-cmdline and therefore overwrite the partition-layout.
We fix this by overwriting the cmdline supplied by the bootloader.
Signed-off-by: David Bauer <mail@david-bauer.net>
The get_status_led() function was removed due to the convertion to dts
alias based status led.
Since we don't need the boardname any longer, the functions.sh include
isn't required any more.
Fixes: c9c4b2116c ("ramips: Use dts alias based status led")
Signed-off-by: Mathias Kresin <dev@kresin.me>
With a10a204aab ("kernel: make ubi auto-attach check for a tar file
magic") the check for the magic was added without considering a failing
mtd_read(). If the read fails, no check is done and the mount code is
called straight away.
Failing with an error message for such cases seems to me the cleaner way,
as it would allow to spot hidden/workaround issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The first block(s) of the ubi mtd device might be bad. We need to take
care on our own to skip the bad block(s) and read the next one(s).
Don't treat recoverable read errors as fatal and check for the UBI magic
if the data of a block could be recovered using ECC or similar.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the put_mtd_device() called on multiple error conditions to a goto
label to use it later for more error conditions.
The early return on failed open of the mtd device and mismatching mtd
type allows to get rid of one level of indentation. By jumping to the
cleanup code, a refcount bug is fixed for the wrong flash type condition.
While at it, make clear that we only check for the UBI magic if the read
from flash was successful.
Signed-off-by: Mathias Kresin <dev@kresin.me>
By takimata:
"Come to think of it, an MBL Single board boots up just fine on an
MBL Duo image, and the MBL Single board identifies completely
identical to the MBL Duo
(Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB).
I wonder if there is any downside to just using the MBL Duo firmware
on a MBL Single. I wonder if the two firmwares could even be unified."
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All these devices share the exact same image format.
The usb3 kmod is added for the rbm11g, as the rbm11g has a mini-pcie
slot like its bigger sibling. The usb kmod is necessary for
usb-over-pcie support, which is mandatory for a lot of LTE modules.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.
Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info
LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)
The Fon LED is labeled as internet in avm gpl sources.
Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)
Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC
PCIe
GPIO#21: reset (active low)
Installation:
To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
ftp> quote REBOOT
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Use of_mdiobus_register() to pass the ethernet phy node to the phy
drivers. This is needed for the at8030 phy driver which needs to know
the GPIO which is connected to the ar8030 reset pin.
This driver expects a child in gsw/etop node named "mdio-bus", which has
the ethernet phys defined:
&gsw {
phy-mode = "rmii";
phy-handle = <&phy0>;
mtd-mac-address = <&ath9k_cal 0xa91>;
mtd-mac-address-increment = <(-2)>;
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
};
};
};
Fallback to mdiobus_register() if no mdio-bus child node exists. This
way we don't need to touch all xway dts files, for which we don't know
the actual address on the mdio bus.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
The mac address for the 2.4 wireless need to be decremented by one.
Correct MAC adress increments for this board are:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Drop the parallel-unsafe custom Build/dtb macro and use the .dtb artifacts
produced by the generic image build code.
Also remove unused .dtb references in the mt7623 subtarget.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
F9K1115v2 has a kernel partition size of 1408 kB.
Since kernel 4.9.x+ the kernel image for this device compiled had exceeded
the kernel partition size limit and thus failing size check.
The kernel image generated for this device
under ar71xx tiny target is 1329.67 kB < 1408 kB.
Signed-off-by: Kin Chan <kcchan1@outlook.com>
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD
Specifications:
* SoC: Qualcomm QCA9533 (650MHz)
* RAM: 32MiB
* Storage: 16MiB SPI NOR flash
* Ethernet: 3x100M
* Wireless: QCA9533 built-in, dual-chain 802.11b/g/n
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its Internet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Now connect the board via either of its LAN ports (2 or 3).
6. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
7. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
8. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
SOC: BCM63168 (BMIPS4350 V8.0 @400MHz)
Flash size: 16 MiB
RAM size: 128 MiB
Heavily based on patch for OpenWRT Chaos Chalmer.
Original patch and more info can be found at:
https://openwrt.org/toh/sky/sr102
Known issues:
- Wireless and ADSL modem are not working.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" could very
well fix the freezes that have been reported on the forum by
@ticerex and @takimata.
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/46>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The code has some remaining issues that cause ethernet hangs, so
disable it for now until we can get it fixed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The line that produces factory image was accidentally left by me while
testing before inital commit.
I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).
I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.
So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Extend the small_flash feature to disable swap, core dumps, and
kernel debug info, and change the squashfs block size to 1024KiB.
Also change squashfs fragment cache to 2 for small_flash to ease memory
usage.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add a new config option to allow to select the default compile
optimization level for the kernel.
Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.
Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.
Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.
Exceptions to the above are:
- lantiq, where the optimization for size is only required for the
xway_legacy subtarget but was set for the whole target
- mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
plenty of space and an optimization for size doesn't make much sense
- rb532, which has 128MByte flash
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move boards to the tiny subtarget which break the build if the kernel is
set to "Optimize for performance".
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the latest version of u-boot (2018.05) there was a swith to
Hush shell for ARC AXS10x boards(arc770/archs38):
commit 9249d74781e1 ("ARC: AXS10x: Enable hush shell").
In Hush shell using "$()" to declare envitonment variables is forbidden,
instead of this "${}" need to be used.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
The changed applied to BananaPi R2 in upstream commit c0b0d540db1a,
which was backported to 4.14 in 4.14.53, is also required for the U7623.
Without updating the memory node, the board refuses to boot.
Fixes: d0839e020d ("kernel: bump 4.14 to 4.14.53")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align
Let the MTD core take care of both
Fixes messages like these:
[ 102.820541] Data buffer not 16 bytes aligned: 87daf08c
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Newer kernels have a patch that implements compatible functionality
directly. Adjust the attribute of our own patch in preparation for
dropping it later
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rereshed all patches
Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.
This fixes UBI support for devices that have kernel flashed on partition
with a bad block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit adds support for the OCEDO Raccoon
SOC: Atheros AR9344
RAM: 128MB
FLASH: 16MiB
WLAN1: AR9344 2.4 GHz 802.11bgn 2x2
WLAN2: AR9382 5 GHz 802.11an 2x2
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
NOTE: The U-Boot won't boot with the serial attached.
Boot the device without serial attached and attach it
after 3 seconds.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_USB_MTU3 is not visible for the mediatek target by default, but
only when CONFIG_USB_GADGET is set. This will config option will be
remove with when running "make kernel_oldconfig", move this option to
the generic config to prevent this.
This fixes the build of the mt7623 subtarget of the mediatek target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shrink the tiny kernel by moving all switch and ethernet phy drivers to
the generic kernel config instead of the target kernel config.
All boards in the tiny and nand target are either ar7240 or ar9331 based,
which don't support external xMII and therefore no external ethernet phy
can be connected. None of the boards uses a realtek switch either.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
Add a template for safeloader images and include it instead of
overwriting variables defined in the common tp-link build commands.
Split the existing tp-link templates to proper implement the safeloader
template.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop the LOADER_TYPE variables in case no loader is used at all or move
the variable to devices which are using a loader.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the provided image build variables to point the kernel-bin build
command to the kernel we are interested in.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the LOADER_TYPE variable to specify that we need the elf preloader
and append the loader via the corresponding build recipe. It allows to
enable initramfs images again for mikrotik NAND images, which caused a
build error before.
Add the minor header only to the kernel of the sysupgrade images, as it
is only required for the bootloader to find the kernel on flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Stock firmware:
In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.
(excerpt from dmesg):
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.
If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.
(example):
## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1 !!
## Booting image at bc060000 ...
Image Name: MIPS OpenWrt Linux-4.14.50
Image Type: MIPS Linux kernel Image (lzma compressed)
Data Size: 1865917 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!
Starting kernel ...
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
USB storage support is however SCSI Disk block device support isn't
meaning that connected devices wont enumerate.
Enable CONFIG_BLK_DEV_SD by default to fix it.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
BusyBox's `tar` command does not support the `--directory` directive, which
is essentially `-C` in short-form option.
BusyBox's `tar` command supports `-C`.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
These options are handled by generic configuration
Targets that need these options should select KERNEL_DEVMEM
and/or KERNEL_DEVKMEM options on OpenWRT's config
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC. However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines. If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.
This commit overrides the incorrect dt node definition in the included
file.
See also:
- https://bugs.openwrt.org/index.php?do=details&task_id=1262
- https://community.nxp.com/thread/338432#comment-474107
Signed-off-by: Tim Small <tim@seoss.co.uk>
Add two patches submitted for upstream review that significantly improve
the dwc2 driver on openwrt from kernel stability and performance
perspectives.
Fixes: FS#1367
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order,
i.e. in order to match actual user visible labels, usb1 should be usb2,
and vice versa.
This patch swaps LED and GPIO power control node names.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Due do a missing KCONFIG isn't selectable nor enabled in the target
kernel config. Drop it for now and enable/add the driver at the time it
is required.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Specification:
- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn
Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.
Flash instructions:
1) To flash the recovery image, start a TFTP server with IP address
192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
button and power it up. Keep pressing the WPS/Reset button for
10 seconds or until the lock LED is lighting up.
It will try to download the recovery image and flash it.
It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.
Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button
The device supports dual boot mode. So we use only first half of flash.
Flash instruction:
The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
This commit adds support for the MikroTik RouterBOARD RBM11g.
=Hardware=
The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.
==Switch==
The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.
==Flash==
The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.
==PCIe==
The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.
==USB==
There are no external USB ports.
==Power==
The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.
==Serial port==
The device does have an onboard UART on an unpopulated header next to the
flash chip:
GND: pin 2
TX: pin 7
RX: pin 6
Settings: 115200, 8N1
See below illustration for positioning of the header.
0 = screw hole
* = some pin
T = TX pin
R = RX pin
G = GND pin
Pinout:
+---------------
|O
| __
| / \
| \__/
|
|
|
| +---+
| |RAM|
| +--+ | |
| |**| <- unpopulated header with UART
| |*T| +---+
| |R*| +--------+
| |**| | |
| |G*| | CPU |
| +--+ | |
| +--+ | |
| | | +--------+
| +--+ <- flash chip
|O
| +-----+
| | |
|+--+ | |
|| | | |
+---------------------
=Installation=
To install an OpenWRT image to the device two components must be built:
1. A openwrt initramfs image
2. A openwrt sysupgrade image
===initramfs & sysupgrade image===
Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.
==Installing==
**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**
When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.
1. Set up a dhcp server that points the bootfile to tftp server serving
the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot
Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:
1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
to the device using scp.
2. Write openwrt to flash using "sysupgrade
openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.
Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.
Available flash space for rootfs+overlay increases from 48MB to 124MB.
Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.
Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.
Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.
Signed-off-by: Michael Kuron <m.kuron@gmx.de>
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.
Fixes: FS#1620
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't mask bit 4 of the AT8022 phy id. If bit 4 of the AT8022 phy id
(0x004dd023) is masked, it will match the phy id of the AR8327 switch
(0x004dd033) as well.
It results in applied at803x driver settings/callbacks, which will at
least limit the AR8327 phys to 100MBit operation instead of the possible
1000MBit.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport hot off the press upstream netlink patch. Fixes stats display
from CAKE qdisc on MIPS allowing us to bump CAKE to latest version.
The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.
However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.
Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
In some cases, recent builds fail to boot from flash with at least some
MT7621 based devices. The error message is:
"LZMA ERROR 1 - must RESET board to recover"
Booting the same kernel via TFTP works for some reason.
Through testing I figured out that limiting the LZMA dictionary size
seems to prevent these errors
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch ports the TP-Link TL-WR741ND v4 and TL-WR740ND v4 to the
ath79 target.
Because the two devices share the same hw layout, this patch adds a common
.dtsi which is included by the two .dts.
Signed-off-by: Rocco Folino <rocco@folino.io>
The order of the Ethernet ports were mixed up.
This commit fixes the order to be aligned with the physical layout.
Signed-off-by: Lev <leventelist@gmail.com>
The Unifi AC Mesh is equivalent to the Unifi AC Lite. However,
for setting certain parameters with the flashed device it is
helpful that the devices know their variant (e.g. automatically
setting antenna gain for the different antennas in Lite and Mesh).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- fix sysupgrade check
- move usb to v4 dts because v5 doesn't have it
- make wan mac address behave like ar71xx target
- add orange wan led support, it can be userspace activated like:
on:
echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger
off:
echo none > /sys/class/leds/tp-link\:orange\:wan/trigger
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
rework the dts to a common unifi-ac dtsi
pro network is connected via phy0 and has usb ports
lite network is connected via phy4 without usb ports
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
This target can automatically detect the correct memory size and we've
been using it for long in ar71xx.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The original device support patch configured the amber wlan LEDs (which
are meant as error indicator by the OEM) controlled by the SOC's GPIO
as wlan traffic indicators, as the correct white wlan LEDs are
connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were
not accessible. The recent addition of GPIO/ LED support to ath10k now
makes it possible to use the correct white LEDs instead - and
"mac80211: ath10k: use tpt LED trigger by default" also enables them by
default. While both LEDs are independent of each other (two separate
LEDs sharing one light tunnel), triggering both on wlan traffic is not
the intended behaviour (bright yellow light).
Tested on the ZyXEL NBG6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Move to i2c pins pinmux node to the pinctrl node.
Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")
Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the "firmware" partition definition from the DTS of R7800
to fix sysupgrade.
Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x
and that causes mtd to misbehave as additional kernel and ubi
partitions are detected from inside the "firmware" partition.
[ 1.111324] 0x000001480000-0x000001880000 : "kernel"
[ 1.121005] 0x000001880000-0x000007900000 : "ubi"
[ 1.283912] 0x000007900000-0x000008000000 : "reserve"
[ 1.296407] 0x000001480000-0x000007900000 : "firmware"
[ 1.468043] no rootfs found after FIT image in "firmware"
[ 2.426860] 2 uimage-fw partitions found on MTD device firmware
[ 2.426931] 0x000001480000-0x000001880000 : "kernel"
[ 2.440420] 0x000001880000-0x000007900000 : "ubi"
Both kernel and ubi are already defined in DTS, so this duplication
leads into errors in sysupgrade:
Writing from <stdin> to kernel ...
ubiattach: error!: strtoul: unable to parse the number '6 mtd10'
ubiattach: error!: bad MTD device number: "6 mtd10"
The partition is defined to same area as kernel+ubi, and is not
needed for sysupgrade anymore. Remove it to fix things.
Only tested for the R7800 but all of them should behave equal.
Fixes: FS#1617
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[squashed commits, add "tested on" note]
Signed-off-by: Mathias Kresin <dev@kresin.me>
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0
1-4: lan
0: wan
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Refresh patches.
Remove patch that can be reverse applied:
mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch
mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch
Update patch that no longer applied:
ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch
Compiled-tested-for: lantiq, ramips
Run-tested-on: lantiq BT hh5a, ramips MIR3g
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Michael Yartys <michael.yartys@protonmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Netgear WNR612 v2:
- cpu Atheros AR7240 (Python) @400MHz
- flash 4MB
- ram 32MB
- ethernet 10/100: 1xwan + 2xlan (only two)
- radio AR9285
As there is a rebranded WNR612v2 called ON Networks N150R, add
a dtsi which includes all device support, and add a separate dts
for the device only (with a separate one for the subsequent N150R).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Have mktplinkfw fill in the rootfs offset so the firmware splitter can
find it without aligning to erase blocks.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0
Preparing a TFTP recovery image for initial flashing:
Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!
Create a TFTP recovery image:
1) Download a stock TP-Link Firmware file here:
https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
#> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
#> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin
The resulting image can be flashed via TFTP recovery mode.
Flash instructions:
1) To flash the recovery image, start a TFTP server from IP address
192.168.0.66 and serve the recovery image named
ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
and power it up. Keep pressing the WPS/Reset button for 10 seconds.
It will try to download the recovery image and flash it.
It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.
Use the mii-bus property instead to manage the switch via a mdio bus.
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.
Code was written mostly by Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches
break the possibility for using an ip4ip6 tunnel interface as a fall
back interface accepting ip4-in-ip6 tunneled packets from any remote
address. This works out of the box with any normal (non-666-patched)
kernel and can be configured by setting up an 'ip -6 tunnel' with type
'any' or 'ip4ip6' and a remote address of '::'.
The misbehavior comes with line 290 the patch which discards all packets
that do not show the expected saddr, even if no single fmr rule was
defined and despite the validity of the saddr was already approved earlier.
Signed-off-by: Axel Neumann <neumann@cgws.de>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
This commit adds support for the MT7623A-based UniElec U7623-02 router,
with eMMC storage and 512MB RAM. The router can be delivered with NAND
Flash and more memory, but I only have access to the one configuration.
The DTS is structured in such a way that adding support for
more/different storage/memory should be straight forward.
The device has the following specifications:
* MT7623A (quad-core, 1.3 GHz)
* 512MB RAM (DDR3)
* 8GB storage (eMMC 4.5)
* 2x normal miniPCIe slots
* 1x miniPCIe slot that is connected via an internal USB OTG port
* 5x 1Gbps Ethernet (MT7530 switch)
* 1x UART header
* 1x USB 3.0 port
* 1x SATA 3.0
* 1x 40P*0.5mm FPC for MIPI LCD
* 1x SIM slot
* 12x LEDs (2 GPIO controlled)
* 1x reset button
* 1x DC jack for main power (12V)
The following has been tested and is working:
* Ethernet switch
* miniPCIe slots (tested with Wi-Fi cards)
* USB 3.0 port
* sysupgrade
* reset button
Not working:
* The miniPCIe connected via USB OTG. For the port to work, some MUSB
glue must be added. I am currently in the process of porting the glue
from the vendor SDK.
Not tested:
* SATA 3.0
* MIPI LCD
Installation:
The board ships with u-boot, and the first installation needs to be done
via the bootloader using tftp. Step number one is to update the MBR of
the eMMC, as the one that ships with the device is broken. Since the
device can ship with different storage sizes, I will not provide the
exact steps for creating a valid MBR. However, I have made some
assumptions about the disk layout - there must be one 8MB recovery
partition (FAT32) and a partition for the rootfs (Linux).
The board loads the kernel from block 0xA00 (2560) and I have reserved
32MB for the kernel (65536 blocks). I have aligned the partitions on the
erase block size (4096 byte), so the recovery partition must start on
block 69632 and end on 86016 (16385 sectors). The rootfs is assumed to
start on sector 90112.
In order to install the mbr, you run the following commands from the
u-boot command line:
* tftpboot ${loadaddr} <name of mbr file>
* mmc device 0
* mmc write ${loadaddr} 0x00 1
Run the following commands to install + boot OpenWRT:
* tftpboot ${loadaddr} openwrt-mediatek-mt7623-7623a-unielec-u7623-02-emmc-512m-squashfs-sysupgrade-emmc.bin.gz
* run boot_wr_img
* run boot_rd_img
* bootm
Recovery:
In order to recover the router, you need to follow the installation
steps above (no need to replace MBR).
Notes:
* F2FS is used as the overlay filesystem.
* The device does not ship with any valid MAC address, so a random
address has to be generated. As a work-around, I write the initial
random MAC to a file on the recovery partition. The MAC of the WAN
interface is set to the MAC-address contained in this file on each boot,
and the address of the LAN-interfaces are WAN + 1. The MAC file is kept
across sysupgrade/firstboot.
My approach is slightly different than what the stock image does. The
first fives bytes of the MAC addresses in the stock image are static,
and then the last byte is random. I believe it is better to create fully
random MAC addresses.
* In order to support the miniPCIe-slots, I needed to add missing
pcie-nodes to mt7623.dtsi. The nodes are just c&p from the upstream
dtsi.
* One of the USB3.0 phys (u3phy2) on the board can be used as either USB
or PCI, and one of the wifi-cards is connected to this phy. In order to
support switching the phy from USB to PCI, I needed to patch the
phy-driver. The patch is based on a rejected (at least last time I
checked) PCI-driver submitted to the linux-mediatek mailing list.
* The eMMC is configured to boot from the user area, and according to
the data sheet of the eMMC this value can't be changed.
* I tried to structure the MBR more nicely and use for example a
FAT32-parition for the kernel, so that we don't need to write/read from
some offset. The bootloader does not support reading from
FAT32-paritions. While the command (fatload) is there, it just throws an
error when I try to use it.
* I will submit and hope to get the DTS for the device accepted
upstream. If and when that happens, I will update the patches
accordingly.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
set device and tftp server IP address and input the firmware
file name. U-boot will then load the firmware and write it into
the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit adds support for the Mikrotik RouterBOARD RBM33g.
=Hardware=
The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.
==Switch==
The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:
port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU
==Flash==
The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.
==PCIe==
The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.
Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:
PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11
==USB==
The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:
open: USB on PCIe 1 is active
closed: USB on rear USB port is active
==Power==
The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.
=Installation=
==Prerequisites==
A USB -> RS-232 Adapter and a null modem cable are required for
installation.
To install an OpenWRT image to the device two components must be built:
1. A openwrt initramfs image
2. A openwrt sysupgrade image
===initramfs & sysupgrade image===
Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.
==Installing==
**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**
Serial settings: 115200 8N1
The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:
1. Set up a dhcp server that points the bootfile to tftp server serving
the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet
On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.
1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
using scp.
2. Write openwrt to flash using "sysupgrade
openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"
Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Arvid E. Picciani <aep@exys.org>
Apparently there are RPi1 devices with BRCM43430 wifi, such as the
Pi Zero W. Add the necessary packages for that to the image generated
for those boards as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the missing enable and disable function.
Remove dummy mask and unmask function and use the one provided by
irq_dummy_chip.
Allow interrupt status register being defined from dts.
Add ddr_wb_flush for ar934x/qca953x.
Rename controller name to qca,ar9340-intc because this design was
first introduced in AR934x.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 57600 bps
Flash instruction using factory image:
1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新（アップデート）")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
Specification:
- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
- RX, TX, NC, GND, Vcc from power connector side
- baudrate: 115200 bps
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
/dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
fw_setenv ipaddr "192.168.0.1"
fw_setenv serverip "192.168.0.2"
fw_setenv autostart "yes"
fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add wpad-mini if wireless drivers are included. Drop the mt76 package if
both of the provided drivers are included with their own packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Currently arc770 is no more "source-only".
Lets update Linux kernel version from 4.9 to 4.14 for arc770.
config-4.14 was simply regenerated with "make kernel_menuconfig".
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot
Installation:
1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
- Boot device: try ethernet once then NAND
- Boot protocol: DHCP
- Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image, e.g.
openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
"try ethernet once then NAND," press and hold the reset button while
powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
pressed from the previous step.
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.
Revert to RouterOS
Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: David Ehrmann <ehrmann@gmail.com>
GRO stores packets as fraglist. If they are routed back to the ethernet
device, they need to be re-segmented if the driver does not support
sending fraglists.
Add the missing support for that, along with a missing feature flag that
allows full routed GRO->TSO offload.
Considerably reduces CPU utilization for routing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit adds support for the AVM Fritz!WLAN Repeater 450E
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- Most LEDs
Not working:
- 2 RSSI LEDs
AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
While it is possible to implement this feature, it would require an
additional kernel patch for a minor functionality.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
The QCA9556 only has a SGMII interface. However the speed on the
ethernet link is set for the non-existant xMII interface.
This commit fixes this behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable the Hardware Random Number Generator Core infrastructure
in kernel.
Needed for hardware random number generator drivers like chaoskey
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as
dynamic ftrace depends on -mlong-calls.
See http://patchwork.linux-mips.org/patch/675/
Thus we always set -mlong-calls if the kernel is being
compiled with dynamic ftrace support.
Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
Marvell ahci hardware requires a workaround to prevent eSATA failures
on hotplug/reset when used with multi-bay external enclosures.
Errata Ref#226 - SATA Disk HOT swap issue when connected through Port
Multiplier in FIS-based Switching mode.
These patches backport the workaround from 4.17.
Signed-off-by: Jeremiah McConnell <miah@miah.com>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
ar71xx/ar913x series use the old pll registers and settings.
However started from ar7242, a new pll register is introduced and the
pll setting is much simpler.
This can be observed from dev-eth.c from the ar71xx target.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds dts for qca956x and also support for Phicomm K2T
The qca965x.dtsi adds nearly all the necessary components.
Both ath9k AHB and PCIe worked well.
The Phicomm K2T uses MTD partition 'config' to store the mac addresses in
JSON format. To extract these fields correctly, a script is introduced:
/lib/functions/k2t.sh
This script provides a helper function to extract mac addresses, and is used
in three places.
Hardware spec of Phicomm K2T:
CPU: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337
WiFi 5.8GHz: QCA9886
Flash instruction:
Apply sysupgrade.bin via serial console:
tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This fixup ip align in essedma driver rx path
see cat /proc/cpu/alignment
which reports alignment-fixups without this fix.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Backport a hot off the press upstream kernel ATM fix:
Preserve value of skb->truesize when accounting to vcc
"There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs. Ideally it would cover ATM too. It doesn't. Just
stashing the accounted value and using it in atm_raw_pop() is probably
the easiest way to cope."
The issue was exposed by upstream with:
commit 14afee4b6092fde451ee17604e5f5c89da33e71e
Author: Reshetova, Elena <elena.reshetova@intel.com>
Date: Fri Jun 30 13:08:00 2017 +0300
net: convert sock.sk_wmem_alloc from atomic_t to refcount_t
But an earlier commit left the ticking timebomb:
158f323b9868 ("net: adjust skb->truesize in pskb_expand_head()
Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging
assistance and to David Woodhouse <dwmw2@infradead.org> for further
guidance, cajoling & patience in interpreting the debug I was giving him
and producing a fix!
Fixes FS#1567
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77
we incorrectly updated our hack integration patch that updates atm/common.c
+++ b/net/atm/common.c
@@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc
write_unlock_irq(&vcc_sklist_lock);
}
+struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL;
+EXPORT_SYMBOL(ifx_atm_alloc_tx);
+
static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size)
{
struct sock *sk = sk_atm(vcc);
+ if (ifx_atm_alloc_tx != NULL)
+ return ifx_atm_alloc_tx(vcc, size)
The correct solution is to drop our ifx_atm_alloc_tx replacement hack
entirely and let the kernel do its thing.
In reality neither pppoatm or BR2684 interfaces actually hit this code,
so the incorrect integration would only be noticed with direct socket
calls which we are unaware of a use-case.
This is not the solution to pppoatm vc-mux failing to work which started
the whole investigation, but let's fix it up anyway.
With sincerest thanks to David Woodhouse <dwmw2@infradead.org> &
Mathias Kresin <dev@kresin.me>.
Tested-on: lantiq, BT HomeHub 5a
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Support for these devices isn't ready yet and it was only accidentally
pushed in the commit 0da9303e5b ("mac80211: backport "brcmfmac:
cleanup and some rework" from 4.17").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
For easier future kernel bumps replace spi patch with upstream version
slightly modified. The modification removes partition definitions which
has been diffrent for some U-Boot versions.
Also this removes unnecessary i2c definition which was in the old patch.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since the beginning there's been an issue with initializing the Atheros
based MiniPCIe wireless cards. Here's an example of kerenel log:
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit]
pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref]
[...]
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k 0000:00:00.0: enabling device (0000 -> 0002)
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40
ath9k 0000:00:00.0: request_irq failed
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k: probe of 0000:00:00.0 failed with error -22
The same happens for ath5k cards, while ath10k card didn't appear at
all (not detected):
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link never came up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
advk-pcie d0070000.pcie: config read/write timed out
Following the issue on esppressobin.net forum [1] the workaround seems
to be limiting the speed of PCIe bridge to 1st generation. This fixed
the initialisation of all tested Atheros wireless cards.
The change shouldn't affect the performance for wireless cards,
it could reduce the performance of storage controller cards but since
OpenWrt focuses on wireless connectivity, fixing compatibility with
wireless cards should be a priority.
For the record, the iwlwifi and mt76 cards were not affected by this
issue.
1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
zram.ko needs CONFIG_BLK_DEV activated and it is by default for all
other targets in OpenWrt.
This makes zram.ko compile again.
Compile tested only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Neon and vfpv4 are mandatory extensions in the ARM64 instruction set
now, do not activate them explicitly. GCC will make use of these
extension now by default.
This makes it possible to share the toolchain with other Cortex A53
SoCs.
Compile tested only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the get_status_led method to diag.sh, which sets the
boot-led as status-led for scripts using this method to get a
status-led.
This method is used platform-independent in downstream project gluon to
set the LED used to indicate the config-mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
This generates the "rd.gz" and "hddapp.tgz" that doesn't contain
anything of the sort but rather the OpenWRT rootfs. It works the
same way as how we generate the same layout for the NAS4220b.
For some reason the ImageInfo file is different for the SQ201.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The D-Link DIR-685 has a RealTek RT2880 mini-PCI card in a
slot. Activate the appropriate kernel module.
The Square One SQ201 has a Ralink RT61-based mini-PCI card.
Activate the appropriate kernel modules. This fixes the
previous error just activating the firmware: the kernel
module will bring in the firmware it needs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the Gemini build a WRGG-type firmware update
image for the DIR-685. This should hopefully install the
kernel from the web firmware upgrade API on the product
switching it permanently to use OpenWRT.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It was described by Arend as:
> This series is intended for 4.17 and includes following:
>
> * rework bus layer attach code.
> * remove duplicate variable declaration.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes missing rootfs on above device:
[ 2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
(...)
[ 2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Fixes: 05cb6aa69f ("bcm53xx: replace linux,part-probe with a proper partitions subnode")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1. Move all status led definitions out of diag.sh into device dt
as we use here a generic script hook.
2. Encode "phy0ptp" led trigger in dt of device for all ath79 devices.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Fixes for WNDR3800 DTS:
* fix bootcmd
* name art partition to reference it for MACs
* format firmware partition's address similarly as others
* make u-boot-env read-only like in ar71xx
* read wan and lan MACs from art
* fix LED and button gpio values to match ar71xx
(orange/green powerLED, reset button)
* enable power LED in dts by alias led-status
* define USB LED triggers and connect to USB port
* change wifi button to KEY_RFKILL like in ar71xx
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Add support for the common led property "linux,default-trigger". It
allows to set a default led trigger via devicetree.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Readd SoC compatible strings and correct model names mangled in
a51078f735, cleanup dts to remove
duplication, rename dtsi for clarity, use correct GPIO for TL-MR10U
USB power.
Tested only on TL-WR703N due to lack of a TL-MR10U.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch
Flash instruction:
The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
With this change, the LED trigger is independent from the (wireless)
netdev name. The (wireless) netdev name can be easiliy changed in
OpenWrt and would require an update of the netdev trigger settings each
time it is done.
This change is (for now) applied only to MT7628 devices from TP-Link, as
we only had the possibility to test this change against two of those
devices, namely a TL-WR841 v13 and a Archer C50 v3.
Signed-off-by: David Bauer <mail@david-bauer.net>
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.
Set the correct register address and size in the dtsi file to get the
watchdog working.
Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device
min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which
is [68, 1500] by default.
It's necessary to set a max_mtu if a mtu > 1500 is supported.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Recent Speedport firmware downloads only work over HTTPS, so the user
either needs to provide the already downloaded file or install
ustream-ssl-* as well as ca-certificates or ca-bundle.
So to get VDSL2 with vectoring on xRX200, simply run
vdsl_fw_install.sh
on the target and either provide the downloaded file as instructed or
make sure the device is connected to the Internet and can download that
HTTPS url itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ship EEPROM blobs for specific supported board only and don't have them
lurking around in our source tree but rather download them from
@github/RPi-Distro/firmware-nonfree upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This was caused by a race condition between offload teardown and
conntrack gc bumping the timeout of offloaded connections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some of the Marvell targets have functional SATA port multiplier
support, which is required for multi-bay eSATA enclosures. Enable
kernel support by setting CONFIG_SATA_PMP.
Closes: FS#1232 and FS#547
Signed-off-by: Jeremiah McConnell <miah@miah.com>
This device has only one ethernet port.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[add the existing eth0 as lan block, shorten commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The AVM package selection partially broke with the addition of the
FRITZ!Box 4020. This commit restores the intended behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
Just name buttons directly, rather than abstract and then also a label.
Likewise for leds. Avoids DTC warnings about unit address with no reg
parameter.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Make the unitname match the reg address. This fixes a DTC warning.
Tested that USB is still functional on an ar9331 device including this
dtsi.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Based on original ar71xx eg200 board files
Tested working:
* usb hub, storage and serial port
* ethernet
* wifi
* leds
* button
sysupgrade from self->self passes validity checks.
sysupgrade from old ar71xx->ath79 passes. (however this doesn't migrate
wireless driver configs)
Only unknown issue is the existance of a /sys/class/leds/ath9k-phy0,
which doesn't "exist"
Signed-off-by: Karl Palsson <karlp@etactica.com>
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.
Specification:
- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The ART partition of the Lima board stores exactly three mac addresses:
* 0x0: eth0
* 0x6: eth1
* 0x1002: wmac
The first two are correctly assigned in the mach file but the latter points
to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the
driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when
it doesn't find a valid mac address in the platform_data.
Remove this bogus offset to the ART partition to directly load the wmac via
the EEPROM data in the ART partition.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Node /cpus/cpu@0 has a unit name, but no reg property
Node /cpus/cpu@1 has a unit name, but no reg property
Node /cpuintc@0 has a unit name, but no reg property
Node /cpuclock@0 has a unit name, but no reg property
Node /sysclock@0 has a unit name, but no reg property
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This reverts commit 8a570921b5.
This seems to have been accidentally reverted. This fixes mt7620 and
mt7628.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.
The GPO is now controlled by the USB driver via the voltage regulator
definition. The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)
USB port power is enabled on driver load and disabled on driver unload.
Enable kernel support for fixed voltage regulator types on mt7621.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch fixes a dtc warning that shows up for every device
Warning (unit_address_vs_reg): Node /soc/ad-hoc-bus has a reg or ranges property, but no unit name
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
qcom-ipq4018-ex6100v2.dtb: Warning (reg_format): "reg" property in
/led_spi/led_gpio@0 has invalid length (4 bytes)
qcom-ipq4018-ex6100v2.dtb: Warning (avoid_default_addr_size):
Relying on default #size-cells value for /led_spi/led_gpio@0
Cc: Thomas Hebb <tommyhebb@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.
Toggling a gpio selects the output to which USB is connected.
Since kernel 4.9, gpio base is rounded up to a value of 32.
Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.
But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.
Switching the USB port to mPCIe now shows my modem is correctly discovered again:
[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11
Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.
Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.
In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.
Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit
Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52
Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The board_name was being tested for "xlnx,zynq-zybo",
but the .dts compatible string is "digilent,zynq-zybo"
Also, sorted the boards alphabetically, and added an
error message for unsupported boards
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This is no longer necessary since commit 57776e6
(base-files: remove default /etc/config/network,
generate it via board.d instead)
Run-tested: ZedBoard
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
After commit a1248da (zynq: convert to new image build code),
all boards, became unbootable, entering into a boot loop.
Replace the compressed kernel zImage by an uncompressed Image,
which is compressed after with gzip. Also, enable the creation
of an initramfs image by default.
Change images' filename to match the compatible string from the
respective .dts file (<vendor>_<model>). Also, use the shared
mkits.sh script and remove the target specific one.
Fixes: FS#1204
Run-tested: ZedBoard
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Some board vendors actually changed the loader to expect the chip
to come up in 4-address-mode and flipped the ADP bit in the flash
chip's configuration register which makes it come up in 4-address-mode.
Hence it doesn't make sense to avoid switching to 4-address-mode on
those boards but the opposite as otherwise reboot hangs eg. on the
WrtNode2 boards. Fix this by checking the ADP register and only using
SPI_NOR_4B_READ_OP on chips which have ADP==0 (come up in 3-byte mode).
See also datasheet section 7.1.11 Power Up Address Mode (ADP)
Fixes: 22d982ea0 ("ramips: add support for switching between 3-byte and 4-byte addressing on w25q256 flash")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.
While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.
Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.
Fixes: e39847ea2f ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Import all improvements made in the lzma-loader since development on the
ath79 target started.
This also reverts fe594bf90d ("ath79: fix loader-okli, lzma-loader"), as
is obsoleted by 2ad60168b6af ("ar71xx: lzma-loader: move padding workaround
to gzip step").
Likely, many of the changes should be ported to the ramips lzma-loader as
well, but I don't have a device to test this.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.
This approach had two issues:
- The padding was only working when .data was non-empty (otherwise the
section would become NOBITS, omitting it in the binary). .data was only
empty when no CMDLINE was set, leading to further workarounds like
fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
workaround was only effective because a missing "const" led to the kernel
argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
uncompressed .bin and .elf loaders. The prevented embedding the kernel
cmdline in the loader for non-gz loader types.
To fix both issues, move the creation of the padding from the linker script
to the gzip step.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
