This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
This patch refreshes the ipq806x kernel patches.
There was a large PR for ipq806x in the queue when the kernel patches
were refreshed for 4.4.32, so currently there is quite much fuzz for
ipq806x.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver
Also switching to ondemand frequency scaling as it is fixed now
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO
For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f
For debugging serial console is easily visible on board, no soldering needed.
Signed-off-by: André Valentin <avalentin@marcant.net>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
-add spi pins
-move mdio and rgmii pinctrl from gmac and mdio into pinmux node
-add i2c4 pinctrl into rpm node
-add pin details into several nodes
-update gmac1 and gmac2 parameters
-update mdio phy0 and phy4 registers by ddwrt devs findings
-fix i2c4 pin drive-strengh
-remove pcie pins as it's already present in ipq8065 DT
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The R7800 is an IPQ8065, so rename its dts file to reflect that fact.
Also fold the R7500v2 dts addition into the existing 800-devicetree.patch.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes instability/corruption on the ethernet interface connected to port0 on the switch on Netgear R7800 as well.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The ATB DTB mangle code will enter an infinite loop if it encounters a
word in the command line that contains an r in the middle of the word.
Fix this by increasing ptr everytime before invoking strchr, ot avoid
finding the same r again.
This fixes booting at least on Netgear R7500v1, which contains
"ubi.mtd=rootfs" in its commandline, triggering the misbehaviour.
Fixes: 0ddcbee261 ("ipq806x: activate ATAG DTB mangle and EA8500 rootblock in dts")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Calibration data for QCA99x0 in this device has bogus macaddress.
The data cannot be modified directly, as it breaks checksum control.
Instead change the macaddress from phy add hotplug event.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
The command-line arguments provided by the boot loader will be
appended to a new device tree property: bootloader-args.
If there is a property "append-rootblock" in DT under /chosen
and a root= option in bootloaders command line it will be parsed
and added to DT bootargs with the form: <append-rootblock>XX.
Only command line ATAG will be processed, the rest of the ATAGs
sent by bootloader will be ignored.
This is usefull in dual boot systems, to get the current root partition
without afecting the rest of the system.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
This reverts commit 53147c2237.
These config changes break booting on C2600 and probably other devices.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
In commit "regulator: qcom: Rework to single platform device" the smb208
regulator used in IPQ8064 was left out.
Add it to that new framework and update Docs and DT accordingly.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
1)Changes
- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime
2)Testing
Tested on IPQ AP148 Board:
a. NOR boot and NAND boot
b. ethernet network and ath10k wifi
c. ubi sysupgrade
UnTested
dwc3 usb has not been validated on IPQ board(AP148)
3)Known Issues:
Once we flash ubi image on AP148, and if we reset the board, uboot on
first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
and not what linux expects which causes errors when trying to mount rootfs.
In order to test this, we can use the below steps:
a. Flash the ubi image on board and don't reset the board
b. load the kernel fit image in RAM and boot from there.
Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
AP148 uses lowercase name as boardname, so we need to use this in
platform.sh as well.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48304
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
