Commit graph

19759 commits

Author SHA1 Message Date
Mathias Kresin
53624c1702 ramips: fix dtc warnings
Fix individual boards dtc warnings or obvious mistakes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
6384e0d16a ramips: fix hnat dtc warning
The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.

Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
f9b8328d79 ramips: fix pci/pcie related dtc warnings
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.

Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.

Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.

If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.

Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.

Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
d8e7a526a3 ramips: use ralink,nr-gpio instead of ralink,num-gpios
Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.

Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
1bad2b74ae ramips: fix cpu interrupt controller dtc warnings
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
b9dbf3f3c8 ramips: fix cpu related dtc warnings
We need a reg property if we are using a unit address.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
René van Dorst
0ae9396556 treewide: convert gpio-export to platform driver
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.

gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.

Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
1d18a14a90 ath79: really fix TP-Link Archer C7 v2 MAC address
Revert 290c54473e ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.

Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.

The correct MAC adress increments for this board are:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

Fixes: FS#408

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Koen Vandeputte
f960490fc8 kernel: bump 4.14 to 4.14.60
Refreshed all patches

Removed upstreamed patches:
- 500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-03 16:10:38 +02:00
Koen Vandeputte
4ec4dd2a11 kernel: bump 4.9 to 4.9.117
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-03 16:10:38 +02:00
Jo-Philipp Wich
4bb8a678e0 sdk: include arch/arm/ Linux includes along with arch/arm64/ ones
The Linux headers on arm64 architectures contain references to common
arch/arm/ headers which were not bundled by the SDK so far.

Check if we're packing the SDK for an arm64 target and if we do, also
include arch/arm headers as well.

Fixes FS#1725.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-03 13:47:29 +02:00
Jonas Gorski
2308b87204 brcm63xx: switch to 4.14
Kernel 4.14 support has been present for quite some time, so let's give
it wider testing.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:49:18 +02:00
Jonas Gorski
15cb65dad7 brcm63xx: drop b43 from devices with unsupported wifi
The internal wifi isn't supported, so drop b43 from devices that only
have it.

Fixes FS#1698
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Jonas Gorski
8cb8d70fea brcm63xx: copy SR102 support patch to 4.14 as well
It seems to have been missed when the patch was accepted.

Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Jonas Gorski
bc1c706bb3 brcm63xx: drop bogus SPROM section from SR102
The integrated SoC wifi will likely never be supported, and if,
it will go through DT with the sprom contents there.

Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Andrew Cameron
bae927c551 ar71xx: add support for TP-LINK CPE510 V2.0
Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2018-08-02 07:49:26 +02:00
Jo-Philipp Wich
b9bd3285c7 Revert "ar71xx: ag71xx: Prevent kernel oops for board def"
This reverts commit 7a3e133751.

This change reportedly breaks connectivity on some ar71xx devices, so
revert it for now.

Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:34:22 +02:00
Jo-Philipp Wich
33dbe2c55d Revert "ar71xx: ag71xx: Add connect message: fixed phy"
This reverts commit 0b9f4e8808.

This change reportedly breaks connectivity on some ar71xx devices, so
revert it for now.

Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:31:37 +02:00
Jo-Philipp Wich
9ebf596386 Revert "ar71xx: ag71xx_phy: Fix compilation for debug messages"
This reverts commit 2655fbe8ef.

The patch introduces syntax errors, revert it for now.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:31:14 +02:00
Daniel F. Dickinson
0b7a9688ce ar71xx: cr3000: cleanup board definition
1) Add comments so it's clear why we did things; this may prevent
   someone (e.g. me) from sinking time into fixing things that
   aren't broken and/or were done for reason.

2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0.

3) Cosmetic reording of some code (tested) that makes the defintion
   more clear.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
b6c8bc0981 ar71xx: cr3000: Use correct company name
It's 'PowerCloud Systems' not 'PowerCloud'.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
e38520cd50 ar71xx: cr3000: Drop support for defunct cloud
The CR3000 stock firmware is now irrelevant as it required a now defunct
cloud service.  Therefore only build images that use the entire flash
(overwriting stock firwmare-specific partitions that no longer matter),
previously called 'nocloud' images.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
60cf71ede7 ath79: Forward port support for CR3000
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering.  It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:

1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.

2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.

3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.

4) eth0 is wan and eth1 is lan (switch)

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:53 +02:00
Koen Vandeputte
fec8fe8069 kernel: bump 4.9 to 4.9.116
Refreshed all patches

Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch

Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.

Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9

Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-01 09:46:59 +02:00
Jo-Philipp Wich
d0e0b7049f sdk: bundle usbip userspace sources
Bundle the usbip utility sources shipped with the Linux kernel tree in
order to allow the usbip packages from the package feed to build within
the OpenWrt SDK.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 09:12:17 +02:00
Stijn Tintel
77e3e706ce kernel: add missing ARM64_SSBD symbol
In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for
ARM64. Add this symbol to all ARM64 targets using kernel 4.14.

This mitigates CVE-2018-3639 on ARM64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 12:22:11 +03:00
Daniel Golle
7dcdf16222 kernel: remove duplicate #define's in at803x Ethernet PHY driver
AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.

Fixes: f791fb4af4 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-07-31 05:28:48 +02:00
Daniel Golle
a497e47762 kernel: re-add patch for AT8032 Ethernet PHY
The patch was wrongly removed by a kernel version bump to 4.9.105 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.

Fixes: 7dca1bae82 (kernel: bump to 4.9.105)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-07-31 04:56:58 +02:00
Stijn Tintel
ef025e6417 kernel: add pending e1000e fixes
The previous round of fixes for the 82574 chip cause an issue with
emulated e1000e devices in VMware ESXi 6.5. It also contains changes
that are not strictly necessary. These patches fix the issues introduced
in the previous series, revert the unnecessary changes to avoid
unforeseen fallout, and avoid a case where interrupts can be missed.

The final two patches of this series are already in the kernel, so no
need to include them here.

Patchwork: https://patchwork.ozlabs.org/cover/881776/

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:34 +03:00
Stijn Tintel
22b9f99b87 kernel: bump 4.14 to 4.14.59
Drop patch that was superseded upstream:
ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch

Drop upstreamed patches:
- apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch
- apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch
- ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch
- generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch
- generic/pending/900-gen_stats-fix-netlink-stats-padding.patch

In 4.14.55, a patch was introduced that breaks ext4 images in some
cases. The newly introduced patch
backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
addresses this breakage.

Fixes the following CVEs:
- CVE-2018-10876
- CVE-2018-10877
- CVE-2018-10879
- CVE-2018-10880
- CVE-2018-10881
- CVE-2018-10882
- CVE-2018-10883

Compile-tested: ath79, octeon, x86/64
Runtime-tested: ath79, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:07 +03:00
Matt Merhar
a2eaaaaf4b kernel: switch compatible property for RedBoot DT binding
This changes the DT binding's compatible property to
"ecoscentric,redboot-fis-partitions", removing the existing reference to
Red Hat.

Per the documentation hosted at eCosCentric's website, eCosCentric is
RedBoot's sole commercial maintainer since 2002, and the project has
been under the stewardship of the Free Software Foundation since 2008.

This also updates the property in the Inventel Livebox 1 .dts, the
binding's only current user.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-07-30 23:49:49 +02:00
John Crispin
5f5d812881 brcm2708: fix w1 patch
this is now part of generic

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-30 20:51:56 +02:00
Sven Eckelmann
e3b8ae2b09 ipq40xx: Limit usable channels for OpenMesh A62 PHYs
The OpenMesh A62 is a tri-band device (1x 2.4GHz, 2x 5GHz) with special
filters in front of the RX+TX paths to the 5GHz PHYs. These filtered
channel can in theory still be used by the hardware but the signal strength
is reduced so much that it makes no sense.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-07-30 20:46:13 +02:00
Matt Merhar
af3b1756f0 ath79: fix irq assignment for pci-ar71xx driver
In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.

The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.

While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-07-30 20:22:44 +02:00
Thibaut VARÈNE
c6ee683d64 ar71xx: define switch for rb-952ui-5ac2nd
QCA9533 built-in switch can be configured

Tested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 18:14:30 +02:00
Mantas Pucka
3dd692cd6b ipq40xx: fix booting secondary CPU cores
95672e04 broke booting secondary cores by removing 'qcom,saw' property
from L2 cache node. kpssv2_release_secondary() requires it.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2018-07-30 17:55:04 +02:00
John Crispin
eddf4eae97 ar71xx: fix TL-WR1043N v5 port mapping
fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.")

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-30 17:47:06 +02:00
Tim Thorpe
5660c8fb20 ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.
Reversed the numbering of the LAN ports in Luci so as to match the port numbers on the housing.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2018-07-30 16:31:18 +02:00
Tim Thorpe
d834ad9ac3 ar71xx: TL-WR1043N v4/v5: add orange WAN LED support
Add missing definitions for the orange WAN LED on the
TL-WR1043N(D) v4 and v5.

Change the name of a MAC address offset constant to
make it consistent with the format of the
existing constants.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2018-07-30 16:30:34 +02:00
Lucian Cristian
accb67e582 ath79: add support for tl-wr841n-v9
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 16:14:49 +02:00
INAGAKI Hiroshi
ce93445cd6 ramips: add support for ELECOM WRC-2533GST
ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
  - MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-30 15:55:21 +02:00
Paul Spooren
869b0d11db imagebuilder: add function to show manifest
Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list

This PR is based on the work of @fewckert[1] with slight improvements.

Add function `manifest` to show the manifest of the produced image,
before actually building it. The manifest contains an orderd list of
package name and version.

This is usefull to check package dependencies but also determine a
unique and reproducible image name before building the package. The
sysupgrade server[2] builds images on request with individual package
selection. To distignish between created images which contain differnt
packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the
manifest's content. So far the image was renamed afterwards as the
manifests content was unknown, however this corrupts the signed
sha256sums. This patch allows a clean solution as to dtermine the
manifest in advance and set the EXTRA_IMAGE_NAME accordingly.

[1]: https://github.com/lede-project/source/pull/1591
[2]: https://github.com/aparcar/attendedsysupgrade-server

Signed-off-by: Paul Spooren <mail@aparcar.org>
2018-07-30 15:55:21 +02:00
Kjel Delaey
8492ad0cc1 x86: add support to set GRUB menu entry title
$ make menuconfig

        Target Images -> Title for the menu entry in GRUB

Signed-off-by: Kjel Delaey <kjel_delaey@hotmail.com>
2018-07-30 15:55:21 +02:00
Ademar Arvati Filho
27b2f0fc0f kirkwood: add support for Iomega Storcenter ix2-200
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
 Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
 flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console

Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.13
    tftpboot 0x00800000 factory.bin
    nand erase 0x100000 $(filesize)
    nand write 0x00800000 0x100000 $(filesize)
    run bootcmd
    ```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
    ```
    mkfs.ext2 -L ext2 /dev/sdh1
    mount -t ext2 /dev/sdh1 /mnt
    cp initramfs-uImage /mnt/initramfs.bin
    umount /mnt
    ```
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
    ```
3. log into openwrt and sysupgrade to install into flash
    ```
    sysupgrade -n /tmp/sysupgrade.bin
    ```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-30 15:21:00 +02:00
Jianhui Zhao
84c212da44 samsung/s5pv210: New target
Signed-off-by: Jianhui Zhao <jianhuizhao329@gmail.com>
2018-07-30 14:10:00 +02:00
Keith Maika
4caab80830 ar71xx: add support for TP-Link Archer C59 v2
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
2018-07-30 14:04:45 +02:00
Rafał Miłecki
a3d2448fae kernel: add missing include to redboot.c
This fixes:
drivers/mtd/redboot.c:299:34: error: array type has incomplete element type 'struct of_device_id'

Fixes: 5e8b4be531 ("kernel: add DT binding support to the mtd redboot parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-30 12:07:06 +02:00
Rafał Miłecki
23197e4580 brcm63xx: update DT RedBoot binding for the Inventel Livebox 1
linux,part-probe should be avoided as its only supported with OpenWrt
downstream patch that is going to be dropped eventually.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-07-30 11:16:42 +02:00
Jo-Philipp Wich
d7d10f2c1e brcm47xx: rework model detection
On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.

Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.

As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.

Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.

Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-07-30 11:10:47 +02:00
Lucian Cristian
569b6c8246 omap: disable ubifs
ubifs image are not working, until there is a fix, disable them

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Lucian Cristian
ca529e60d2 omap: add support for f2fs/ext4 overlay creation
add kernel support and include the tools for creating an overlay partition (f2fs or ext4)

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Lucian Cristian
6a095e8587 omap: add sysupgrade support
add sysupgrade missing script files

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Lucian Cristian
40f66f1431 omap: rename image for sysupgrade compatibility
for sysupgrade to work we need to change the image name based on dts target name

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Lucian Cristian
f9af9be8ab omap: fix squashfs image boot and creation
fixes FS#1034, squash fs images fails to boot because of missing ARM BCJ filter decoder
also activate squashf image creation

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Mathew McBride
08714738d2 layerscape: add Traverse LS1043-S support
The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.

Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.

This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.

Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Mathew McBride
481f870a02 layerscape: add multiple-configuration generator for FIT images
This is required for the Traverse LS1043 family, we generate a FIT image
that works on all boards across the family. This is done by creating
multiple configurations that select the right DTB for the board.

The bootloader on these boards is configured to boot like this:
bootm $kernel_load#ls1043s
bootm $kernel_load#ls1043v

This is based on earlier work by Jason Wu for Zynq:
https://lists.openwrt.org/pipermail/openwrt-devel/2016-March/040460.html

Modified to add FDT load addresses and multiple configurations with DTB.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Mathew McBride
2203815f05 layerscape: add support for fixed-link on RGMII interfaces
This is required on the Traverse LS1043 boards to support SFP
and xDSL plug-ins.

This will not be needed on kernel 4.14.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Mathew McBride
40120ca670 layerscape: enable QorIQ thermal driver
This provides access to the CPU die temperature sensor and
the thermal throttling integration

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Mathew McBride
efc1096ef0 layerscape: remove DEVICE_TYPE=developerboard
The Traverse LS1043 series are router boards and need the default router package
selection

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Pawel Dembicki
aa5838adb7 kernel: generic: fix problem with w1-gpio-custom
In boards with fdt is impossible to use kmod-w1-gpio-custom.
w1-gpio-custom create platform structure for w1-gpio module,
but if board use fdt, data is ignored in w1-gpio probe.

This workaround fix the problem.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-07-30 10:43:37 +02:00
Thibaut VARÈNE
3fd4db76b0 ramips: fix RBM11G name
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:43:37 +02:00
Thibaut VARÈNE
a9494bb425 ramips: fix RBM33G name
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:43:37 +02:00
LoveSy
974a2b1aa9 ramips: mmc: Add SD card support to HC5661A
Tested on HC5661A and it now fixes the issue that when enabling sd card
in HC5661A, the wan and 3 lan ports will down.

Known issue:
- When enabling SD card support, the led light of system will down and the rest 2 lights keep working.

Signed-off-by: LoveSy <shana@zju.edu.cn>
2018-07-30 10:43:37 +02:00
LoveSy
3a8efaef00 ramips: mmc: Fix init for MT7628AN
There is another thing about crc to do when initialize SD card on
MT7628.
This commit is to fix this init issue.

Signed-off-by: LoveSy <shana@zju.edu.cn>
2018-07-30 10:43:37 +02:00
张鹏
53a4502013 ar71xx:add support for E750G v8
Qxwlan E750G v8 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (PoE support)
 - 2x 10/100/1000 Mbps Ethernet
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
张鹏
ac03d51a3f ar71xx:add support for E750A v4
Qxwlan E750A v4 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 5G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (one port with PoE support)
 - 1x miniPCIe slot (USB 2.0 bus only)
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
张鹏
b74f63f81d ar71xx:add support for E558 v2
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.

Specification:

 - 720/600/200 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz (QCA9558)
 - 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
 - 4x miniPCIe slot (USB 2.0 bus only)
 - 1x microSIM slot
 - 5x LED (4 driven by GPIO)
 - 1x button (reset)
 - 1x 3-pos switch
 - 1x DC jack for main power input (9-48 V)
 - UART (JP5) and LEDs (J8) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
Daniel F. Dickinson
7a3e133751 ar71xx: ag71xx: Prevent kernel oops for board def
The driver is written in such a way that with a board defintion that
connects a fixed phy, mdio, and switch in a certain way, a kernel oops could
result because of lack of previously probed mdio bus.

This commit allows for easier debugging in this case by casting the
correct blame with serial console messages.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:36 +02:00
Daniel F. Dickinson
0b9f4e8808 ar71xx: ag71xx: Add connect message: fixed phy
It's a little noisier but makes it obvious when the ar7240 switch was
connected to the MDIO bus, and to which phy device (or the failure
to do so).

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:35 +02:00
Daniel F. Dickinson
2655fbe8ef ar71xx: ag71xx_phy: Fix compilation for debug messages
NB: Error only appears with ag71xx debug messages and dynamic printk
enabled.  This is probably why no one has caught it before.

Previously phy probe debug messages used old (now wrong) functions
to get the phy name for printing.  There was also the chance of
a NULL pointer in the event no phy_device was found.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
7a07b4cff0 ath79: Add switch reset definition in dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
f593020a28 ath79: ag71xx: assert a switch reset if defined in dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
a5fa6b3825 ath79: ar724x: Fix reset definition for gmac0/gmac1
reset bit 8 is for builtin switch and bit 12 is marked 'reserved' on datasheet.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
4e5ba50760 ath79: ar7240: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
f43e8f9004 ath79: ag71xx: Explicitly register mdio bus after ag71xx_hw_init() for ar7240
mdio bus isn't a standalone device on ar7240. (and maybe older SoCs?)
Use simple-mfd for ar7241 and later SoCs to get mdio1 ready before gmac0
For ar7240 and older chips, manually create platform device after
ag71xx_hw_init() in ag71xx_probe()to get mdio0 ready between
ag71xx_hw_init() and ag71xx_phy_connect().

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
85189e4c00 ath79: ag71xx: Rework mdio clock settings
Allow specifying desired mdio clock frequency in dts.
Use default frequency around 5MHz for builtin switch and 2MHz for other mdio bus.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
bb7fac4369 ath79: ar7242: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
113b4cf90f ath79: ar7241: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
b6c8e5deae ath79: Fix support for TP-LINK Archer C7 v2
Remove mdio1 and phy1 handle. AR8327N is controlled through mdio0.
Add gmac-config for Archer C7.
Remove ucidef_set_interfaces_lan_wan. They can be determined by config_generate automatically.

The following are for adding support for WDR4900 v2/Archer C7 v1 and other
devices that shared the same machine file in ar71xx:
Move mtd partitions to archer-c7-v2.dts. Only Archer C7 v2 has 16M flash.
Flash on Archer C7 v1/TL-WDR4900 v2 is 8M.
Add label for wlan leds. The default trigger for archer c7/wdr4900 is different.
Move wlan5g led to archer-c7-v2.dts. 5G led on WDR4900 is connected to ar9380.
Move rfkill definition to archer-c7-v2.dts. There is no such a button on wdr4900 v2.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
18db385eb7 ath79: qca955x: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
b7a10772d1 ath79: qca956x: Update dts for current ag71xx driver
enable mdio1 by default because mdio1 node is a subnode of eth1
and eth1 node is a "simple-mfd", which makes mdio1 disabled when
eth1 isn't enabled.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
fc1f55ebf4 ath79: qca953x: Add chosen node and specify console in bootargs
Most qca devices use 115200n8 as it's default uart baudrate.
Add 'chosen' node for qca953x like other SoCs in ath79 target.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
e8245c5b3f ath79: qca953x: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Lucian Cristian
e6417390e0 ath79: update qca9533 to new irq driver
Commit c7efc93 renamed controller name
to qca,ar9340-intc and added some functions but qca9533.dtsi was overlooked.
Correct the dtsi and adust it to the new format

Add gmac and correct reset for cascaded irq and build-in switch
Also add the reference clock to soc dtsi so we don't have to have it in every dts

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>

Remove switch reset definition
Fix gmac compatible string (We only need SW_PHY_SWAP and SW_PHY_ADDR_SWAP on qca953x so use ar9330-gmac instead of ar9340-gmac.)

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
c7c807cb8c ath79: ar933x: Update dts for current ag71xx driver
gmac0 is always connected to switch phy4 and mdio1 is always needed.
So add phy handle for eth0 and enable mdio1 by default.
Move fixed-link for gmac1 from device dts to ar9331.dtsi because gmac1 is always connected to builtin switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
f6c99241ba ath79: ar934x: Update dts for current ag71xx driver
Enable mdio1 by default because mdio1 is needed when eth1 is enabled.

PS: If a ar9341 device has only one port and you only want to use gmac0,
change compatible of gmac1 to "syscon", "simple-mfd" in dts.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
7ae9e63719 ath79: ag71xx: Make builtin switch driver a separated module
This patch did several things:
1. Probe the builtin switch as a separated mdio device.
2. Register a separated mdio bus for builtin switch.
3. Use generic mdio read/write function instead of calling ag71xx_mdio_mii_read/write directly.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
83d2dbc599 ath79: ag71xx: Split mdio driver into an independent platform device.
We need to have mdio1 belonging to gmac1 initialized before gmac0.
Split it into a separated mdio device to get both mdios ready before probing gmac.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
24cbe27bb7 ath79: ag71xx: Remove ar7240_set_addr and ag71xx_ar7240_start
The builtin switch has it's initial valid mac address(00:00:01:00:00:00).
Since the builtin switch is an independent device, setting mac address of gmac1 to builtin switch isn't a good idea and this makes it impossilbe to split builtin switch apart as an independent platform device.
Remove these functions and apply default VLAN during initialization as a preparation for further driver splitting.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
2d081addb5 ath79: ag71xx: Split gmac config into separated file and add support for ar934x/qca955x.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
b346c37588 ath79: Fix mac reset and gmac compatible in ar934x.dtsi
Also add phy-mode and fixed-link as gmac1 is always connected
to the builtin switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Daniel F. Dickinson
098267db4c ar71xx: cap324: Drop support for defunct cloud
Only build images for straight OpenWrt (using all flash; wipes out
partitions that contain information only important for accessing a
now defunct cloud service with the stock firmware) since the stock
firmware is now irrelevant.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:33 +02:00
Daniel F. Dickinson
37ab944ac5 ar71xx: cap324: Use correct company name
It's 'PowerCloud Systems' not just 'PowerCloud'

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
739eaae9ca ar71xx: cap324: Use correct MAC addresses
The wrong MAC addresses (from the point of view of the physical device
label) were being assigned to the wrong interfaces.  Fix that.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
d2f7dba309 ar71xx: cap324: Use standard eth as static lan
While the stock firmware and previous ar71xx versions of openwrt used the
single ethernet port as a DHCP client, for unmodified openwrt usage it
makes more sense to do the standard openwrt thing and make the ethernet
port a static lan with known address so that users can find the device on
the network more easily.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
fedc826c32 ar71xx: cr5000: use correct company name
It's 'PowerCloud Systems' not just 'PowerCloud'

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
50caf9d452 ar71xx: cr5000: Drop support for defunct cloud
The Skydog cloud service no longer exists hence supporting going back
to stock firmware with cloud support is no longer applicable.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
c666851ce7 ar71xx: cr5000: Tweak switch LED settings
This is basically cosmetic and sets the Port 1-4 LEDs to blink on
10/100/1000M.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
ffc71cd2d0 ar71xx: cr5000: Fix the reset button as KEY_RESTART
The reset button was incorrectly returning KEY_WPS_BUTTON as the key
code.  We want KEY_RESTART., so make that fix.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson
a208e07790 ar71xx: cr5000: board data: Use better macro name
The PCIe wireless MAC address address is better labelled as WMAC
than MAC to emphasize that it is for a wireless interface.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00